summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/realtek
AgeCommit message (Collapse)Author
2025-06-16wifi: rtw89: mcc: update format of RF notify MCC H2C commandChih-Kang Chang
The RF notify MCC H2C command format of 8852C different from other chip, therefore add v0 format to update it. Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250610130034.14692-3-pkshih@realtek.com
2025-06-16wifi: rtw89: extend HW scan of WiFi 6 chips for extra OP chan when concurrencyZong-Zhe Yang
HW scan flow has considered the timing when to get back op for the scanning interface. But, when concurrency, there are two interfaces with connection. The OP channel of another one was not back originally. It then easily lead to connection loss when scanning during concurrency. So, HW scan flow is extended to deal with second OP channel. And, H2C command is also extended to fill second MAC ID. The changes mentioned above are done for WiFi 6 chips first. HW scan has different handling architectures including FW and driver on WiFi 7 chips. Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250610130034.14692-2-pkshih@realtek.com
2025-06-16wifi: rtlwifi: fix possible skb memory leak in _rtl_pci_init_one_rxdesc()Thomas Fourier
When `dma_mapping_error()` is true, if a new `skb` has been allocated, then it must be de-allocated. Compile tested only Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250613074014.69856-2-fourier.thomas@gmail.com
2025-06-16wifi: rtlwifi: rtl8821ae: make the read-only array params static constColin Ian King
Don't populate the read-only array params on the stack at run time, instead make it static const. Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250611135521.172521-1-colin.i.king@gmail.com
2025-06-16wifi: rtlwifi: avoid stack size warning for _read_eeprom_infoArnd Bergmann
txpower_info_{2g,5g} are too big to fit on the stack, but in most of the rtlwifi variants this stays below the warning limit for stack frames. In rtl8192ee and a few others, I see a case where clang decides to fully inline this into rtl92ee_read_eeprom_info, triggering this warning: drivers/net/wireless/realtek/rtlwifi/rtl8192ee/hw.c:2178:6: error: stack frame size (1312) exceeds limit (1280) in 'rtl92ee_read_eeprom_info' [-Werror,-Wframe-larger-than] Mark _rtl92ee_read_txpower_info_from_hwpg() as noinline_for_stack to and mark _rtl92ee_get_chnl_group() as __always_inline to make clang behave the same way as gcc. Inlining _rtl92ee_get_chnl_group helps let the compiler see that the index is always in range. The same change appears to be necessary in all rtlwifi variants. A more thorough approach would be to avoid the use of the two structures on the stack entirely and combine them with the struct rtl_efuse data that is dynamically allocated and holds the same information. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250610092240.2639751-1-arnd@kernel.org
2025-06-10wifi: rtw88: Enable AP and adhoc modes for SDIO againBitterblue Smith
AP mode can be enabled again for SDIO now that the problem was fixed in commit b2effcdc2379 ("wifi: rtw88: sdio: map mgmt frames to queue TX_DESC_QSEL_MGMT") and commit fc5f5a0ec463 ("wifi: rtw88: sdio: call rtw_sdio_indicate_tx_status unconditionally"). Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/5ac60c1c-9cc8-41b8-871c-a067e74f70ea@gmail.com
2025-06-10wifi: rtw88: Rename the RTW_WCPU_11{AC,N} enumsBitterblue Smith
The RTW_WCPU_11AC and RTW_WCPU_11N enums are used to identify two types of microcontrollers used in Realtek chips, but these names are misleading. The "11AC" type was also used in 11n devices (e.g. RTL8733BU, not supported by rtw88), and the "11N" type was also used in 11ac devices (RTL8821AU, RTL8812AU). Rename RTW_WCPU_11AC to RTW_WCPU_3081 and RTW_WCPU_11N to RTW_WCPU_8051. (8051 is well known. It's less clear what 3081 is, but the out of tree drivers use this name.) Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/bfb1099c-db52-4b25-b111-17ab712e9404@gmail.com
2025-06-10wifi: rtw89: 8922a: pass channel information when enter LPSKuan-Chung Chen
Newer firmware requires the driver to pass channel information when switching from normal mode to low power mode; otherwise it will result in poor RX beacon performance. Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250606020437.17160-1-pkshih@realtek.com
2025-06-10wifi: rtw89: add chip_ops::chan_to_rf18_val to get code of RF register valueKuan-Chung Chen
The RF 0x18 register stores radio frequency domain parameters, including band, center channel and bandwidth. This information is used in RF domain. Add a chip_ops to retrieve the RF 0x18 value, which allows driver to query for a specific channel. No logic is changed. Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250606020408.17035-1-pkshih@realtek.com
2025-06-10wifi: rtw89: mac: add dummy handler of MAC C2H event class 27Ping-Ke Shih
The newer firmware add new C2H event class 27, which is to report WiFi role status. Since rtw89 doesn't use the status yet, add a dummy handler to avoid warning: rtw89_8922ae 0000:03:00.0: MAC c2h class 27 func 0 not support Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250606020302.16873-5-pkshih@realtek.com
2025-06-10wifi: rtw89: rfk: support IQK firmware command v1Ping-Ke Shih
Add new IQK firmware command format v1 (with suffix), and rename original command format to v0 for older firmware. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250606020302.16873-4-pkshih@realtek.com
2025-06-10wifi: rtw89: fw: add RFE type to RF TSSI H2C commandZong-Zhe Yang
Append a new field for RFE (RF Front End) type to RF TSSI H2C command. FW has forward compatibility when handling this H2C command, so just need to consider backward cases in FW point of view. | old FW | new FW ------------------------------ old driver | O | X ------------------------------ new driver | O | O Currently only RTL8922A uses this RF TSSI H2C command. Increase its FW format max and will let new FW binary align with it. Then, old driver won't load new FW. Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250606020302.16873-3-pkshih@realtek.com
2025-06-10wifi: rtw89: 8852c: increase beacon loss to 6 secondsKuan-Chung Chen
Intermittent beacon loss from a specific AP causes the connection to be lost. Increasing the beacon loss count can make the connection more stable. Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250606020302.16873-2-pkshih@realtek.com
2025-06-10wifi: rtw89: fix EHT 20MHz TX rate for non-AP STAKuan-Chung Chen
The 4-octet EHT MCS/NSS subfield is only used for 20 MHz-only non-AP STA. Correct the interpretation of this subfield to prevent improper rate limitations. Fixes: f1dfcee2eae9 ("wifi: rtw89: Correct EHT TX rate on 20MHz connection") Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250605114207.12381-6-pkshih@realtek.com
2025-06-10wifi: rtw89: add EHT physts and adjust init flow accordinglyEric Huang
Adding EHT physts and adjust IE bitmap initialization. This setting is for PHY statistic gathering, won't effect functionality. Signed-off-by: Eric Huang <echuang@realtek.com> Signed-off-by: Po-Hao Huang <phhuang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250605114207.12381-5-pkshih@realtek.com
2025-06-10wifi: rtw89: implement channel switch supportZong-Zhe Yang
To support channel switch on STA mode, declare IEEE80211_HW_CHANCTX_STA_CSA and implement ieee80211_ops::switch_vif_chanctx. Handling of CSA procedure still relies on mac80211 SW flow, since FW doesn't support chanctx offload. To support channel switch on AP mode, declare WIPHY_FLAG_HAS_CHANNEL_SWITCH and implement ieee80211_ops::channel_switch_beacon additionally. Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250605114207.12381-4-pkshih@realtek.com
2025-06-10wifi: rtw89: chan: re-config default chandef only when none is registeredZong-Zhe Yang
Previously, default chandef is configured if no chanctx is active, i.e. no chanctx is assigned to some vif. For normal cases, it's fine. However, for impending CSA support, need to consider that one chanctx may be added, or called registered, ahead without being assigned immediately. Then, it will keep inactive, and might be covered by the default one when re-calculating chanctxs happens in certain sequences. So now, don't re-config the default chandef unless no chanctx is registered. Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250605114207.12381-3-pkshih@realtek.com
2025-06-10wifi: rtw89: chan: concentrate the logic of setting/clearing chanctx bitmapZong-Zhe Yang
Originally, the logic for setting bits was wrapped inside the configuring function. However, raw clearing bits, clear_bit, was called directly. To be more paired and more understandable. Concentrate the logic of them into the same function. (don't change logic at all) Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250605114207.12381-2-pkshih@realtek.com
2025-06-10wifi: rtw89: sar: do not assert wiphy lock held until probing is doneFedor Pchelkin
rtw89_sar_set_src() may be called at driver early init phase when applying SAR configuration via ACPI. wiphy lock is not held there. Since the assertion was initially added for rtw89_apply_sar_common() call path and may be helpful for other places in future changes, keep it but move it under RTW89_FLAG_PROBE_DONE test. Found by Linux Verification Center (linuxtesting.org). Fixes: 88ca3107d2ce ("wifi: rtw89: sar: add skeleton for SAR configuration via ACPI") Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250604161339.119954-2-pchelkin@ispras.ru
2025-06-10wifi: rtw89: sar: drop lockdep assertion in rtw89_set_sar_from_acpiFedor Pchelkin
The following assertion is triggered on the rtw89 driver startup. It looks meaningless to hold wiphy lock on the early init stage so drop the assertion. WARNING: CPU: 7 PID: 629 at drivers/net/wireless/realtek/rtw89/sar.c:502 rtw89_set_sar_from_acpi+0x365/0x4d0 [rtw89_core] CPU: 7 UID: 0 PID: 629 Comm: (udev-worker) Not tainted 6.15.0+ #29 PREEMPT(lazy) Hardware name: LENOVO 21D0/LNVNB161216, BIOS J6CN50WW 09/27/2024 RIP: 0010:rtw89_set_sar_from_acpi+0x365/0x4d0 [rtw89_core] Call Trace: <TASK> rtw89_sar_init+0x68/0x2c0 [rtw89_core] rtw89_core_init+0x188e/0x1e50 [rtw89_core] rtw89_pci_probe+0x530/0xb50 [rtw89_pci] local_pci_probe+0xd9/0x190 pci_call_probe+0x183/0x540 pci_device_probe+0x171/0x2c0 really_probe+0x1e1/0x890 __driver_probe_device+0x18c/0x390 driver_probe_device+0x4a/0x120 __driver_attach+0x1a0/0x530 bus_for_each_dev+0x10b/0x190 bus_add_driver+0x2eb/0x540 driver_register+0x1a3/0x3a0 do_one_initcall+0xd5/0x450 do_init_module+0x2cc/0x8f0 init_module_from_file+0xe1/0x150 idempotent_init_module+0x226/0x760 __x64_sys_finit_module+0xcd/0x150 do_syscall_64+0x94/0x380 entry_SYSCALL_64_after_hwframe+0x76/0x7e Found by Linux Verification Center (linuxtesting.org). Fixes: 88ca3107d2ce ("wifi: rtw89: sar: add skeleton for SAR configuration via ACPI") Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250604161339.119954-1-pchelkin@ispras.ru
2025-06-10wifi: rtw89: fix spelling mistake of RTW89_FLAG_FORBIDDEN_TRACK_WORKFedor Pchelkin
Rename RTW89_FLAG_FORBIDDEN_TRACK_WROK -> RTW89_FLAG_FORBIDDEN_TRACK_WORK. Found by Linux Verification Center (linuxtesting.org). Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250603153124.188755-1-pchelkin@ispras.ru
2025-06-10wifi: rtw89: mcc: prevent shift wrapping in rtw89_core_mlsr_switch()Dan Carpenter
The "link_id" value comes from the user via debugfs. If it's larger than BITS_PER_LONG then that would result in shift wrapping and potentially an out of bounds access later. In fact, we can limit it to IEEE80211_MLD_MAX_NUM_LINKS (15). Fortunately, only root can write to debugfs files so the security impact is minimal. Fixes: 9dd85e739ce0 ("wifi: rtw89: debug: add mlo_mode dbgfs") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/aDbFFkX09K7FrL9h@stanley.mountain
2025-06-10wifi: rtw89: pci: add PCI Express error handlingChin-Yen Lee
Sometimes PCIe Advanced Error Reporting(AER), like bad TLP or Data link protocol error, happens due to unstable pci signal or no response from PCI host. pcieport 0000:00:1c.0: AER: Uncorrected (Non-Fatal) error message received from 0000:01:00.0 rtw89_8852be 0000:01:00.0: PCIe Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, (Requester ID) rtw89_8852be 0000:01:00.0: device [10ec:b852] error status/mask=00004000/00400000 rtw89_8852be 0000:01:00.0: [14] CmpltTO (First) rtw89_8852be 0000:01:00.0: SER catches error: 0x4000 pcieport 0000:00:1c.0: AER: device recovery successful rtw89_8852be 0000:01:00.0: FW backtrace invalid key: 0xbb6c3214 ieee80211 phy0: Hardware restart was requested Setup callback function to call SER function to reset driver to recover from these states. Signed-off-by: Chin-Yen Lee <timlee@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250523062711.27213-3-pkshih@realtek.com
2025-06-10wifi: rtw88: pci: add PCI Express error handlingChin-Yen Lee
Sometimes PCIe Advanced Error Reporting(AER), like bad TLP or Data link protocol error, happens due to unstable pci signal or no response from PCI host. pcieport 0000:00:00.0: AER: Multiple Corrected error message received from 0000:00:00.0 pcieport 0000:00:00.0: AER: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID) pcieport 0000:00:00.0: AER: device [14c3:6786] error status/mask=000000c1/00006000 pcieport 0000:00:00.0: AER: [ 0] RxErr (First) pcieport 0000:00:00.0: AER: [ 6] BadTLP pcieport 0000:00:00.0: AER: [ 7] BadDLLP pcieport 0000:00:00.0: AER: Corrected error message received from 0000:00:00.0 pcieport 0000:00:00.0: AER: found no error details for 0000:00:00.0 pcieport 0000:00:00.0: AER: Multiple Corrected error message received from 0000:00:00.0 pcieport 0000:00:00.0: AER: found no error details for 0000:00:00.0 pcieport 0000:00:00.0: AER: Multiple Corrected error message received from 0000:00:00.0 pcieport 0000:00:00.0: AER: found no error details for 0000:00:00.0 Setup callback function to call SER function to reset driver to recover from these states Signed-off-by: Chin-Yen Lee <timlee@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250523062711.27213-2-pkshih@realtek.com
2025-06-10wifi: rtlwifi: Constify struct rtl_hal_ops and rtl_hal_cfgChristophe JAILLET
'struct rtl_hal_ops' and 'struct rtl_hal_cfg' are not modified in these drivers. Constifying this structure moves some data to a read-only section, so increase overall security, especially when the structure holds some function pointers. Constification of rtl_hal_cfg is only needed in rtl8192cu/sw.c On a x86_64, with allmodconfig, as an example: Before: ====== text data bss dec hex filename 10167 5512 128 15807 3dbf drivers/net/wireless/realtek/rtlwifi/rtl8188ee/sw.o After: ===== text data bss dec hex filename 10743 4936 128 15807 3dbf drivers/net/wireless/realtek/rtlwifi/rtl8188ee/sw.o Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/2c3f3d8d8b2f7dcb8cc64cebe89e55720d1d733d.1747500351.git.christophe.jaillet@wanadoo.fr
2025-06-08treewide, timers: Rename from_timer() to timer_container_of()Ingo Molnar
Move this API to the canonical timer_*() namespace. [ tglx: Redone against pre rc1 ] Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com
2025-05-16Merge tag 'rtw-next-2025-05-16' of https://github.com/pkshih/rtwJohannes Berg
Ping-Ke Shih says: ================== rtw-next patches for v6.16 Some fixes and refinements across drivers, and regular development of MLO and STA + P2P concurrency. Major changes are listed below. rtw88: * improve throughput for RTL8814AU rtw89: * support MLO * improve user experience for STA + P2P concurrency * dynamic antenna gain (DAG) with different power by antenna * load SAR tables from ACPI ================== Link: https://patch.msgid.link/17e74675-70cc-43d7-a797-afb937030d34@RTEXMBS04.realtek.com.tw/ Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2025-05-16wifi: rtw89: fix firmware scan delay unit for WiFi 6 chipsChin-Yen Lee
The scan delay unit of firmware command for WiFi 6 chips is microsecond, but is wrong set now and lead to abnormal work for net-detect. Correct the unit to avoid the error. Fixes: e99dd80c8a18 ("wifi: rtw89: wow: add delay option for net-detect") Signed-off-by: Chin-Yen Lee <timlee@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250513125203.6858-1-pkshih@realtek.com
2025-05-16wifi: rtw88: fix the 'para' buffer size to avoid reading out of boundsAlexey Kodanev
Set the size to 6 instead of 2, since 'para' array is passed to 'rtw_fw_bt_wifi_control(rtwdev, para[0], &para[1])', which reads 5 bytes: void rtw_fw_bt_wifi_control(struct rtw_dev *rtwdev, u8 op_code, u8 *data) { ... SET_BT_WIFI_CONTROL_DATA1(h2c_pkt, *data); SET_BT_WIFI_CONTROL_DATA2(h2c_pkt, *(data + 1)); ... SET_BT_WIFI_CONTROL_DATA5(h2c_pkt, *(data + 4)); Detected using the static analysis tool - Svace. Fixes: 4136214f7c46 ("rtw88: add BT co-existence support") Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250513121304.124141-1-aleksei.kodanev@bell-sw.com
2025-05-16wifi: rtw89: mcc: avoid redundant recalculations if no chance to improveZong-Zhe Yang
MCC will track the changes of beacon offset, and trigger a recalculation when the difference is larger than the tolerance. It means that a better pattern is expected after recalculating. However, in the cases which get a worse beacon offset, there is no chance to improve the pattern even if recalculating. So, bypass them. Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250511035217.10410-7-pkshih@realtek.com
2025-05-16wifi: rtw89: mcc: deal with non-periodic NoAZong-Zhe Yang
Originally, MCC just took periodic NoA into account. When the connected GO announces non-periodic NoA and GC side is during MCC, sometimes GC cannot receive beacons well if the MCC scheduling conflicts with the non-periodic NoA planning. After the loss exceeds the tolerable amount, beacon filter will report connection loss. However, in this case, the loss is acceptable. So now, MCC will calculate the range of non-periodic NoA. And then, don't care beacon loss during the range. Besides, rtw89_mcc_fill_role_limit() only makes sense for GC. Remove the redundant check of GO. Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250511035217.10410-6-pkshih@realtek.com
2025-05-16wifi: rtw89: mcc: introduce calculation of anchor patternZong-Zhe Yang
In the cases that two MCC roles' TBTTs are too close or too far, original MCC pattern calculation logic will lead to a result that both roles might not cover its TBTT with sufficient time. Introduce a new calculation logic called anchor pattern for these corner cases. It allows to choose one role as anchor to put its TBTT in the middle of its duration directly. For now, a P2P role has a higher priority to be chosen as an anchor. Then, if able, another role might need to depend on courtesy mechanism to take time from anchor. Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250511035217.10410-5-pkshih@realtek.com
2025-05-16wifi: rtw89: mcc: add courtesy mechanism conditions to P2P rolesZong-Zhe Yang
In one enablement of courtesy mechanism, there is one provider and one receiver. And, receiver can use the provider's time in a given period. But, to make P2P NoA protocol work as expected as possible, GO should be present at the time it doesn't announce absent, and GC should not use the time when GO announces absent. So, don't enable courtesy mechanism if provider is GO or receiver is GC. Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250511035217.10410-4-pkshih@realtek.com
2025-05-16wifi: rtw89: mcc: drop queued chanctx changes when stoppingZong-Zhe Yang
When MCC is about to stop, there may be some chanctx changes which are queued for work but have not yet been run. To avoid these changes from being processed in a wrong state (e.g. next new MCC instance), cancel the queued work and drop queued changes. Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250511035217.10410-3-pkshih@realtek.com
2025-05-16wifi: rtw89: mcc: pass whom to stop at when pausing chanctxZong-Zhe Yang
When stopping MCC, FW can stop at a given MCC role following H2C command. When pausing chanctx during MCC, in general, the caller expects to process things with its chanctx. So, pass the caller as target and let FW stop MCC at it. Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250511035217.10410-2-pkshih@realtek.com
2025-05-16wifi: rtw88: Fix the random "error beacon valid" messages for USBBitterblue Smith
All the USB devices have a problem in AP mode: uploading the updated beacon to the chip's reserved page can randomly fail: [34996.474304] rtw88_8723du 1-2:1.2: error beacon valid [34996.474788] rtw88_8723du 1-2:1.2: failed to download drv rsvd page [34999.956369] rtw88_8723du 1-2:1.2: error beacon valid [34999.956846] rtw88_8723du 1-2:1.2: failed to download drv rsvd page [34999.956855] rtw88_8723du 1-2:1.2: failed to download beacon [35017.978296] rtw88_8723du 1-2:1.2: error beacon valid [35017.978805] rtw88_8723du 1-2:1.2: failed to download drv rsvd page [35017.978823] rtw88_8723du 1-2:1.2: failed to download beacon [35023.200395] rtw88_8723du 1-2:1.2: error beacon valid [35023.200869] rtw88_8723du 1-2:1.2: failed to download drv rsvd page [35023.200875] rtw88_8723du 1-2:1.2: failed to download beacon [35478.680547] rtw88_8723du 1-2:1.2: error beacon valid [35478.681023] rtw88_8723du 1-2:1.2: failed to download drv rsvd page Disable some beacon-related hardware functions before uploading the beacon and enable them again after. Tested with RTL8723DU, RTL8812BU, RTL8822CE. Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/c248c40a-d432-47ed-90e0-d81ee6c32464@gmail.com
2025-05-16wifi: rtw88: usb: Upload the firmware in bigger chunksBitterblue Smith
RTL8811AU stops responding during the firmware download on some systems: [ 809.256440] rtw_8821au 5-2.1:1.0: Firmware version 42.4.0, H2C version 0 [ 812.759142] rtw_8821au 5-2.1:1.0 wlp48s0f4u2u1: renamed from wlan0 [ 837.315388] rtw_8821au 1-4:1.0: write register 0x1ef4 failed with -110 [ 867.524259] rtw_8821au 1-4:1.0: write register 0x1ef8 failed with -110 [ 868.930976] rtw_8821au 5-2.1:1.0 wlp48s0f4u2u1: entered promiscuous mode [ 897.730952] rtw_8821au 1-4:1.0: write register 0x1efc failed with -110 Maybe it takes too long when writing the firmware 4 bytes at a time. Write 196 bytes at a time for RTL8821AU, RTL8811AU, and RTL8812AU, and 254 bytes at a time for RTL8723DU. These are the sizes used in their official drivers. Tested with all these chips. Cc: stable@vger.kernel.org Link: https://github.com/lwfinger/rtw88/issues/344 Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com> Acked-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/43f1daad-3ec0-4a3b-a50c-9cd9eb2c2f52@gmail.com
2025-05-16wifi: rtw88: usb: Reduce control message timeout to 500 msBitterblue Smith
RTL8811AU stops responding during the firmware download on some systems: [ 809.256440] rtw_8821au 5-2.1:1.0: Firmware version 42.4.0, H2C version 0 [ 812.759142] rtw_8821au 5-2.1:1.0 wlp48s0f4u2u1: renamed from wlan0 [ 837.315388] rtw_8821au 1-4:1.0: write register 0x1ef4 failed with -110 [ 867.524259] rtw_8821au 1-4:1.0: write register 0x1ef8 failed with -110 [ 868.930976] rtw_8821au 5-2.1:1.0 wlp48s0f4u2u1: entered promiscuous mode [ 897.730952] rtw_8821au 1-4:1.0: write register 0x1efc failed with -110 Each write takes 30 seconds to fail because that's the timeout currently used for control messages in rtw_usb_write(). In this scenario the firmware download takes at least 2000 seconds. Because this is done from the USB probe function, the long delay makes other things in the system hang. Reduce the timeout to 500 ms. This is the value used by the official USB wifi drivers from Realtek. Of course this only makes things hang for ~30 seconds instead of ~30 minutes. It doesn't fix the firmware download. Tested with RTL8822CU, RTL8812BU, RTL8811CU, RTL8814AU, RTL8811AU, RTL8812AU, RTL8821AU, RTL8723DU. Cc: stable@vger.kernel.org Fixes: a82dfd33d123 ("wifi: rtw88: Add common USB chip support") Link: https://github.com/lwfinger/rtw88/issues/344 Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com> Acked-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/1e35dd26-3f10-40b1-b2b4-f72184a26611@gmail.com
2025-05-16wifi: rtw89: pci: enlarge retry times of RX tag to 1000Ping-Ke Shih
RX tag is sequence number to ensure RX DMA is complete. On platform Gigabyte X870 AORUS ELITE WIFI7, sometimes it needs longer retry times to complete RX DMA, or driver throws warnings and connection drops: rtw89_8922ae 0000:07:00.0: failed to update 162 RXBD info: -11 rtw89_8922ae 0000:07:00.0: failed to update 163 RXBD info: -11 rtw89_8922ae 0000:07:00.0: failed to update 32 RXBD info: -11 rtw89_8922ae 0000:07:00.0: failed to release TX skbs Fixes: 0bc7d1d4e63c ("wifi: rtw89: pci: validate RX tag for RXQ and RPQ") Reported-by: Samuel Reyes <zohrlaffz@gmail.com> Closes: https://lore.kernel.org/linux-wireless/f4355539f3ac46bbaf9c586d059a8cbb@realtek.com/T/#t Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250509013433.7573-1-pkshih@realtek.com
2025-05-16wifi: rtw89: leave idle mode when setting WEP encryption for AP modeDian-Syuan Yang
Due to mac80211 triggering the hardware to enter idle mode, it fails to install WEP key causing connected station can't ping successfully. Currently, it forces the hardware to leave idle mode before driver adding WEP keys. Signed-off-by: Dian-Syuan Yang <dian_syuan0116@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250507031203.8256-1-pkshih@realtek.com
2025-05-16wifi: rtw89: pci: configure manual DAC mode via PCI config API onlyPing-Ke Shih
To support 36-bit DMA, configure chip proprietary bit via PCI config API or chip DBI interface. However, the PCI device mmap isn't set yet and the DBI is also inaccessible via mmap, so only if the bit can be accessible via PCI config API, chip can support 36-bit DMA. Otherwise, fallback to 32-bit DMA. With NULL mmap address, kernel throws trace: BUG: unable to handle page fault for address: 0000000000001090 #PF: supervisor write access in kernel mode #PF: error_code(0x0002) - not-present page PGD 0 P4D 0 Oops: Oops: 0002 [#1] PREEMPT SMP PTI CPU: 1 UID: 0 PID: 71 Comm: irq/26-pciehp Tainted: G OE 6.14.2-061402-generic #202504101348 Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODULE RIP: 0010:rtw89_pci_ops_write16+0x12/0x30 [rtw89_pci] RSP: 0018:ffffb0ffc0acf9d8 EFLAGS: 00010206 RAX: ffffffffc158f9c0 RBX: ffff94865e702020 RCX: 0000000000000000 RDX: 0000000000000718 RSI: 0000000000001090 RDI: ffff94865e702020 RBP: ffffb0ffc0acf9d8 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000015 R13: 0000000000000719 R14: ffffb0ffc0acfa1f R15: ffffffffc1813060 FS: 0000000000000000(0000) GS:ffff9486f3480000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000001090 CR3: 0000000090440001 CR4: 00000000000626f0 Call Trace: <TASK> rtw89_pci_read_config_byte+0x6d/0x120 [rtw89_pci] rtw89_pci_cfg_dac+0x5b/0xb0 [rtw89_pci] rtw89_pci_probe+0xa96/0xbd0 [rtw89_pci] ? __pfx___device_attach_driver+0x10/0x10 ? __pfx___device_attach_driver+0x10/0x10 local_pci_probe+0x47/0xa0 pci_call_probe+0x5d/0x190 pci_device_probe+0xa7/0x160 really_probe+0xf9/0x370 ? pm_runtime_barrier+0x55/0xa0 __driver_probe_device+0x8c/0x140 driver_probe_device+0x24/0xd0 __device_attach_driver+0xcd/0x170 bus_for_each_drv+0x99/0x100 __device_attach+0xb4/0x1d0 device_attach+0x10/0x20 pci_bus_add_device+0x59/0x90 pci_bus_add_devices+0x31/0x80 pciehp_configure_device+0xaa/0x170 pciehp_enable_slot+0xd6/0x240 pciehp_handle_presence_or_link_change+0xf1/0x180 pciehp_ist+0x162/0x1c0 irq_thread_fn+0x24/0x70 irq_thread+0xef/0x1c0 ? __pfx_irq_thread_fn+0x10/0x10 ? __pfx_irq_thread_dtor+0x10/0x10 ? __pfx_irq_thread+0x10/0x10 kthread+0xfc/0x230 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x47/0x70 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK> Fixes: 1fd4b3fe52ef ("wifi: rtw89: pci: support 36-bit PCI DMA address") Reported-by: Bitterblue Smith <rtl8821cerfe2@gmail.com> Closes: https://lore.kernel.org/linux-wireless/ccaf49b6-ff41-4917-90f1-f53cadaaa0da@gmail.com/T/#u Closes: https://github.com/openwrt/openwrt/issues/17025 Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250506015356.7995-1-pkshih@realtek.com
2025-05-10wifi: rtw89: declare MLO support if prerequisites are metZong-Zhe Yang
When the following prerequisites are met, driver will enable support_mlo. It means that driver will declare WIPHY_FLAG_SUPPORTS_MLO, and then deal with MLO related things. The main prerequisites are as below. 1. all prerequisites for running with chanctx 2. FW feature NOTIFY_AP_INFO Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250505072440.45113-12-pkshih@realtek.com
2025-05-10wifi: rtw89: debug: add mlo_mode dbgfsZong-Zhe Yang
Add an dbgfs mlo_mode to get/set MLO mode. And, support to trigger MLSR switching. Setting it will automatically disable MLO Dynamic Mechanism (DM). Then MLO things can follow commands via dbgfs mlo_mode instead of MLO DM. The disabled DM(s) can be checked/cleared via dbgfs disable_dm. The following is an use example. Read it to show current MLD status. $ cat mlo_mode MLD(s) status: (MLO DM: enable) #0: MLO mode 0, valid 0x6, active 0x2 Write it to switch to MLSR on link id 2. $ echo 0 2 > mlo_mode $ cat mlo_mode MLD(s) status: (MLO DM: disable) #0: MLO mode 0, valid 0x6, active 0x4 Besides, to be safer, add RWLOCK attribute to dbgfs disable_dm. Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250505072440.45113-11-pkshih@realtek.com
2025-05-10wifi: rtw89: debug: add FW log component for MLOPo-Hao Huang
This allows showing MLO related logs when FW debug mode is on. Signed-off-by: Po-Hao Huang <phhuang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250505072440.45113-10-pkshih@realtek.com
2025-05-10wifi: rtw89: debug: add MLD table dumpPo-Hao Huang
Add definition for MLD table dump, this is for debug purpose only. Signed-off-by: Po-Hao Huang <phhuang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250505072440.45113-9-pkshih@realtek.com
2025-05-10wifi: rtw89: debug: extend dbgfs for MLOPo-Hao Huang
Extend dbgfs vif/sta info to show current designated link. Signed-off-by: Po-Hao Huang <phhuang@realtek.com> Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250505072440.45113-8-pkshih@realtek.com
2025-05-10wifi: rtw89: add MLO track for MLSR switch decisionPo-Hao Huang
Add MLSR switch mechanism based on tracking RSSI. Switch to a 2 GHz link (if any) when average RSSI is lower than threshold -53. And, switch out from a 2 GHz link when average RSSI is larger than threshold -38. The sequence of MLSR switch handling is like the following. 1. initialize target link and configure to PS mode 2. configure current designated link to PS mode 3. configure target link to non-PS mode 4. deinitialize currently active links except target link The above flow also implies that target link becomes new designated link. Signed-off-by: Po-Hao Huang <phhuang@realtek.com> Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250505072440.45113-7-pkshih@realtek.com
2025-05-10wifi: rtw89: add handling of mlo_link_cfg H2C command and C2H eventZong-Zhe Yang
The mlo_link_cfg H2C command is used to tell FW to enter/leave PS mode on a given link. And, need to wait for status of C2H event to ensure if FW deals with it successfully. Signed-off-by: Po-Hao Huang <phhuang@realtek.com> Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250505072440.45113-6-pkshih@realtek.com
2025-05-10wifi: rtw89: chan: re-calculate MLO DBCC mode during setting channelZong-Zhe Yang
Wi-Fi 7 chips have dual HW bands. After impending MLO support, they can work with HW-[0] / HW-[1] / HW-[0,1] according to active links. So, during setting channel, also re-calculate the MLO DBCC mode flag. Then, leaf chip functions of setting channel can configure with HWs based on current case. Besides, tweak the initial and idle MLO DBCC mode of Wi-Fi 7 chips to MLO_1_PLUS_1_1RF to work with dual HW bands. And, after disconnecting, due to no active links, MLO DBCC mode will re-calculate to idle case, i.e. MLO_1_PLUS_1_1RF. Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250505072440.45113-5-pkshih@realtek.com
2025-05-10wifi: rtw89: send nullfunc based on the given linkPo-Hao Huang
The nullfunc sender function is link specific. Use core_tx_write_link with sw_mld flag to TX the nullfunc via the given link. Signed-off-by: Po-Hao Huang <phhuang@realtek.com> Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://patch.msgid.link/20250505072440.45113-4-pkshih@realtek.com
generated by cgit (git 2.34.1) at 2025-09-18 04:19:33 +0000