| Age | Commit message (Collapse) | Author |
|---|
|
9116 device id entry is added in both SDIO and USB interfaces.
New enumberation value taken for the device model. Based on the
device model detected run time, few device specific operations
needs to be performed.
adding rsi_dev_model to get device type in run time, as we can use
same driver for 9113 and 9116 except few firmware load changes.
Signed-off-by: Siva Rebbagondla <siva8118@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Removing redundant device id's from both usb and sdio idtables, as rsi
driver currently supporting only one module(RS9113). Also, replaced ids
with specific defines.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Firmware's watchdog timer should be disabled as a part of reset
sequence. This change fixes a firmware hang issue observed during
stress tests.
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Curretly, RX packet processing is done sequencially. To improve
the efficiency, RX skb queue is introduced.
Here, while preparing RX URB skb is allocated and used
for RX buffer. When rx done handler is called, enqueue the skb
to rx_q and set the thread event.
RX thread is modified to dequeue packets from skb queue and
process further.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
USB endpoint 1 is used for WLAN which is presently in use.
USB endpoint 2 is introduced for BT Rx traffic. Enumeration
of Rx BT endpoint and submitting Rx BT URB are added.
>From /sys/kernel/debug/usb/devices,
Ad=81(I) is for WLAN EP IN and Ad=01(O) is for Wlan EP OUT.
Ad=82(I) is for BT EP IN and Ad=02(O) is for BT EP OUT.
T: Bus=01 Lev=01 Prnt=01 Port=09 Cnt=03 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1618 ProdID=9113 Rev= 0.02
S: Manufacturer=Redpine Signals, Inc.
S: Product=Wireless USB Network Module
S: SerialNumber=000000000001
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 2mA
I:* If#= 0 Alt= 0 #EPs= 6 Cls=00(>ifc ) Sub=00 Prot=00 Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Rx bluetooth endpoint shall be added in further patches. Rx control
block is introduced here to handle Rx packets properly. Separate
function is written to initialize the RX control blocks.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
4 bytes is fixed size for reading or writing USB register. We
will use a macro instead of hardcoding this.
Fixes: b97e9b94ad75c ("rsi: Add new host interface operations")
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
These endpoints are for WLAN and BT protocols.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We need to reset the chip in teardown path so that it can work
next time when driver is loaded. This patch adds support for this
reset configuration for USB.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The older firmware loading method is not usable by any Redpine chipset.
Hence removing that part of the code. Older firmware image with
rsi_91x.fw name is deprecated
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
USB read and write registers maximum size is limited 2^16. More than
this size is not used in the driver.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
RSI_USB_BUF_SIZE macro is used instead of hardcoding a buffer
size to 4096.
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch adds the Redpine Signals' 91x wireless driver.
Signed-off-by: Fariya Fatima <fariyaf@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
