summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ti
AgeCommit message (Collapse)Author
2020-01-26wlcore: mesh: Add support for RX Broadcast KeyMaital Hahn
In order to support authentication of equals peers, need to save RX Broadcast key per peer (on top of 1 TX broadcast key and unicast key per peer). Signed-off-by: Maital Hahn <maitalm@ti.com> Acked-by: Guy Mishol <guym@ti.com> Signed-off-by: Hari Nagalla <hnagalla@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-11-27Merge tag 'mmc-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmcLinus Torvalds
Pull MMC updates from Ulf Hansson: "These are the updates for MMC and MEMSTICK for v5.5. Note that this also contains quite some additional changes reaching beyond both the MMC and MEMSTICK subsystems. This is primarily because of fixing an old regression for a WiFi driver based on the SDIO interface on an OMAP openpandora board MMC core: - Add CMD13 polling for MMC IOCTLS with R1B response. - Add common DT properties for clk-phase-delays for various speed modes. - Fix size overflow for mmc gp-partitions. - Re-work HW reset for SDIO cards, which also includes a re-work for Marvell's WiFi mwifiex SDIO func driver. MMC host: - jz4740: Add support for X1000 and JZ4760. - jz4740: Add support for 8-bit bus and for low power mode. - mmci: Add support for HW busy timeout for the stm32_sdmmc variant. - owl-mmc: Add driver for Actions Semi Owl SoCs SD/MMC controller. - renesas_sdhi: Add support for r8a774b1. - sdhci_am654: Add support for Command Queuing Engine for J721E. - sdhci-milbeaut: Add driver for the Milbeaut SD controller. - sdhci-of-arasan: Add support for ZynqMP tap-delays. - sdhci-of-arasan: Add support for clk-phase-delays for SD cards. - sdhci-of-arasan: Add support for Intel LGM SDXC. - sdhci-of-aspeed: Allow inversion of the internal card detect signal. - sdhci-of-esdhc: Fixup workaround for erratum A-008171 for tunings. - sdhci-of-at91: Improve support for calibration. - sdhci-pci: Add support for Intel JSL. - sdhci-pci: Add quirk for AMD SDHC Device 0x7906. - tmio: Enable support for erase/discard/trim requests. MMC/OMAP/pandora/wl1251: The TI wl1251 WiFi driver for SDIO on the OMAP openpandora board has been broken since v4.7. To fix the problems, changes have been made cross subsystems, but also to OMAP2 machine code and to openpandora DTS files, as summarized below. Relevant changes have been tagged for stable. - mmc/wl1251: Re-introduce lost SDIO quirks and vendor-id for wl1251 - omap/omap_hsmmc: Remove redundant platform config for openpandora - omap_hsmmc: Initialize non-std SDIO card for wl1251 for pandora - omap/dts/pandora: Specify wl1251 through a child node of mmc3 - wl1251: Add devicetree support for TI wl1251 SDIO" * tag 'mmc-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (73 commits) dt-bindings: mmc: Correct the type of the clk phase properties Revert "mmc: tmio: remove workaround for NON_REMOVABLE" memstick: Fix Kconfig indentation mmc: sdhci-of-arasan: Add support for ZynqMP Platform Tap Delays Setup dt-bindings: mmc: arasan: Document 'xlnx,zynqmp-8.9a' controller firmware: xilinx: Add SDIO Tap Delay nodes mmc: sdhci-of-arasan: Add support to set clock phase delays for SD dt-bindings: mmc: Add optional generic properties for mmc mmc: sdhci-of-arasan: Add sampling clock for a phy to use dt-bindings: mmc: arasan: Update Documentation for the input clock mmc: sdhci-of-arasan: Separate out clk related data to another structure mmc: sdhci: Fix grammar in warning message mmc: sdhci-of-aspeed: add inversion signal presence mmc: sdhci-of-aspeed: enable CONFIG_MMC_SDHCI_IO_ACCESSORS mmc: sdhci_am654: Add Support for Command Queuing Engine to J721E mmc: core: Fix size overflow for mmc partitions mmc: tmio: Add MMC_CAP_ERASE to allow erase/discard/trim requests net: wireless: ti: remove local VENDOR_ID and DEVICE_ID definitions net: wireless: ti: wl1251 use new SDIO_VENDOR_ID_TI_WL1251 definition mmc: core: fix wl1251 sdio quirks ...
2019-11-21drivers: net: Fix Kconfig indentation, continuedKrzysztof Kozlowski
Adjust indentation from spaces to tab (+optional two spaces) as in coding style. This fixes various indentation mixups (seven spaces, tab+one space, etc). Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-15net: wireless: ti: remove local VENDOR_ID and DEVICE_ID definitionsH. Nikolaus Schaller
They are already included from mmc/sdio_ids.h and do not need a local definition. Fixes: 884f38607897 ("mmc: core: move some sdio IDs out of quirks file") Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Acked-by: Kalle Valo <kvalo@codeaurora.org> Cc: <stable@vger.kernel.org> # v4.11+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-11-15net: wireless: ti: wl1251 use new SDIO_VENDOR_ID_TI_WL1251 definitionH. Nikolaus Schaller
SDIO_VENDOR_ID_TI_WL1251 is now defined in mmc/sdio_ids.h separately from SDIO_VENDOR_ID_TI for wl1271. Fixes: 884f38607897 ("mmc: core: move some sdio IDs out of quirks file") Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Acked-by: Kalle Valo <kvalo@codeaurora.org> Cc: <stable@vger.kernel.org> # v4.11+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-11-15net: wireless: ti: wl1251 add device tree supportH. Nikolaus Schaller
We will have the wl1251 defined as a child node of the mmc interface and can read setup for gpios, interrupts and the ti,use-eeprom property from there instead of pdata to be provided by pdata-quirks. Fixes: 81eef6ca9201 ("mmc: omap_hsmmc: Use dma_request_chan() for requesting DMA channel") Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Acked-by: Kalle Valo <kvalo@codeaurora.org> Cc: <stable@vger.kernel.org> # v4.7+ [Ulf: Fixed up some complaints from checkpatch] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-11-05Merge tag 'wireless-drivers-next-2019-11-05' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for 5.5 First set of patches for 5.5. The most active driver here clearly is rtw88, lots of patches for it. More quiet on other drivers, smaller fixes and cleanups all over. This pull request also has a trivial conflict, the report and example resolution here: https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au Major changes: rtw88 * add deep power save support * add mac80211 software tx queue (wake_tx_queue) support * enable hardware rate control * add TX-AMSDU support * add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support * add power tracking support * add 802.11ac beamformee support * add set_bitrate_mask support * add phy_info debugfs to show Tx/Rx physical status * add RFE type 3 support for 8822b ath10k * add support for hardware rfkill on devices where firmware supports it rtl8xxxu * add bluetooth co-existence support for single antenna iwlwifi * Revamp the debugging infrastructure ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-28net: Fix misspellings of "configure" and "configuration"Geert Uytterhoeven
Fix various misspellings of "configuration" and "configure". Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-11wlcore: clean-up clearing of WL1271_FLAG_IRQ_RUNNINGTony Lindgren
We set WL1271_FLAG_IRQ_RUNNING in the beginning of wlcore_irq(), but clear it before interrupt handling is done in wlcore_irq_locked(). Let's move the clearing to the end of wlcore_irq() where it gets set, and remove the old comments about hardirq. That's no longer the case as we're using request_threaded_irq(). Note that the WL1271_FLAG_IRQ_RUNNING should never race between the interrupt handler and wlcore_runtime_resume() as because of autosuspend timeout we cannot enter idle between wlcore_irq_locked() and the end of wlcore_irq(). Cc: Anders Roxell <anders.roxell@linaro.org> Cc: Eyal Reizer <eyalr@ti.com> Cc: Guy Mishol <guym@ti.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-10-02net/wireless: Use kmemdup rather than duplicating its implementationFuqian Huang
kmemdup is introduced to duplicate a region of memory in a neat way. Rather than kmalloc/kzalloc + memcpy, which the programmer needs to write the size twice (sometimes lead to mistakes), kmemdup improves readability, leads to smaller code and also reduce the chances of mistakes. Suggestion to use kmemdup rather than using kmalloc/kzalloc + memcpy. Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-07-26mac80211: pass the vif to cancel_remain_on_channelEmmanuel Grumbach
This low level driver can find it useful to get the vif when a remain on channel session is cancelled. iwlwifi will need this soon. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Link: https://lore.kernel.org/r/20190723180001.5828-1-emmanuel.grumbach@intel.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-07-20wireless: fix nl80211 vendor commandsJohannes Berg
In my previous commit to validate a policy I neglected to actually add one to the few drivers using vendor commands, fix that now. Reported-by: Tony Lindgren <tony@atomide.com> Tested-by: Tony Lindgren <tony@atomide.com> Fixes: 901bb9891855 ("nl80211: require and validate vendor command policy") Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-07-11Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-nextLinus Torvalds
Pull networking updates from David Miller: "Some highlights from this development cycle: 1) Big refactoring of ipv6 route and neigh handling to support nexthop objects configurable as units from userspace. From David Ahern. 2) Convert explored_states in BPF verifier into a hash table, significantly decreased state held for programs with bpf2bpf calls, from Alexei Starovoitov. 3) Implement bpf_send_signal() helper, from Yonghong Song. 4) Various classifier enhancements to mvpp2 driver, from Maxime Chevallier. 5) Add aRFS support to hns3 driver, from Jian Shen. 6) Fix use after free in inet frags by allocating fqdirs dynamically and reworking how rhashtable dismantle occurs, from Eric Dumazet. 7) Add act_ctinfo packet classifier action, from Kevin Darbyshire-Bryant. 8) Add TFO key backup infrastructure, from Jason Baron. 9) Remove several old and unused ISDN drivers, from Arnd Bergmann. 10) Add devlink notifications for flash update status to mlxsw driver, from Jiri Pirko. 11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski. 12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes. 13) Various enhancements to ipv6 flow label handling, from Eric Dumazet and Willem de Bruijn. 14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van der Merwe, and others. 15) Various improvements to axienet driver including converting it to phylink, from Robert Hancock. 16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean. 17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana Radulescu. 18) Add devlink health reporting to mlx5, from Moshe Shemesh. 19) Convert stmmac over to phylink, from Jose Abreu. 20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from Shalom Toledo. 21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera. 22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel. 23) Track spill/fill of constants in BPF verifier, from Alexei Starovoitov. 24) Support bounded loops in BPF, from Alexei Starovoitov. 25) Various page_pool API fixes and improvements, from Jesper Dangaard Brouer. 26) Just like ipv4, support ref-countless ipv6 route handling. From Wei Wang. 27) Support VLAN offloading in aquantia driver, from Igor Russkikh. 28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy. 29) Add flower GRE encap/decap support to nfp driver, from Pieter Jansen van Vuuren. 30) Protect against stack overflow when using act_mirred, from John Hurley. 31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen. 32) Use page_pool API in netsec driver, Ilias Apalodimas. 33) Add Google gve network driver, from Catherine Sullivan. 34) More indirect call avoidance, from Paolo Abeni. 35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan. 36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek. 37) Add MPLS manipulation actions to TC, from John Hurley. 38) Add sending a packet to connection tracking from TC actions, and then allow flower classifier matching on conntrack state. From Paul Blakey. 39) Netfilter hw offload support, from Pablo Neira Ayuso" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits) net/mlx5e: Return in default case statement in tx_post_resync_params mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync(). net: dsa: add support for BRIDGE_MROUTER attribute pkt_sched: Include const.h net: netsec: remove static declaration for netsec_set_tx_de() net: netsec: remove superfluous if statement netfilter: nf_tables: add hardware offload support net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload net: flow_offload: add flow_block_cb_is_busy() and use it net: sched: remove tcf block API drivers: net: use flow block API net: sched: use flow block API net: flow_offload: add flow_block_cb_{priv, incref, decref}() net: flow_offload: add list handling functions net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free() net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_* net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND net: flow_offload: add flow_block_cb_setup_simple() net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC ...
2019-07-03Merge branch 'timers/vdso' into timers/coreThomas Gleixner
so the hyper-v clocksource update can be applied.
2019-06-24wl18xx: Fix Wunused-const-variableNathan Huckleberry
Clang produces the following warning drivers/net/wireless/ti/wl18xx/main.c:1850:43: warning: unused variable 'wl18xx_iface_ap_cl_limits' [-Wunused-const-variable] static const struct ieee80211_iface_limit wl18xx_iface_ap_cl_limits[] = { ^ drivers/net/wireless/ti/wl18xx/main.c:1869:43: warning: unused variable 'wl18xx_iface_ap_go_limits' [-Wunused-const-variable] static const struct ieee80211_iface_limit wl18xx_iface_ap_go_limits[] = { ^ The commit that added these variables never used them. Removing them. Cc: clang-built-linux@googlegroups.com Link: https://github.com/ClangBuiltLinux/linux/issues/530 Signed-off-by: Nathan Huckleberry <nhuck@google.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-06-22timekeeping: Use proper clock specifier names in functionsJason A. Donenfeld
This makes boot uniformly boottime and tai uniformly clocktai, to address the remaining oversights. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Link: https://lkml.kernel.org/r/20190621203249.3909-2-Jason@zx2c4.com
2019-06-19treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500Thomas Gleixner
Based on 2 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation # extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 4122 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Enrico Weigelt <info@metux.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-05treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 336Thomas Gleixner
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details you should have received a copy of the gnu general public license along with this program if not write to the free software foundation inc 51 franklin st fifth floor boston ma 02110 1301 usa extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 246 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Alexios Zavras <alexios.zavras@intel.com> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190530000436.674189849@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-21treewide: Add SPDX license identifier - Makefile/KconfigThomas Gleixner
Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-05Merge tag 'wireless-drivers-next-for-davem-2019-05-03' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for 5.2 Most likely the last patchset of new feature for 5.2, and this time we have quite a lot of new features. Most obvious being rtw88 from Realtek which supports RTL8822BE and RTL8822CE 802.11ac devices. We have also new hardware support for existing drivers and improvements. There's one conflict in iwlwifi, my example conflict resolution below. Major changes: iwlwifi * bump the 20000-series FW API version * work on new hardware continues * RTT confidence indication support for Fine Timing Measurement (FTM) * an improvement in HE (802.11ax) rate-scaling * add command version parsing from the fimware TLVs * add support for a new WoWLAN patterns firmware API rsi * add support for rs9116 mwifiex * add support for SD8987 brcmfmac * add quirk for ACEPC T8 and T11 mini PCs rt2x00 * add RT3883 support qtnfmac * fix debugfs interface to support multiple cards rtw88 * new driver mt76 * share more code across drivers * add support for MT7615 chipset * rework DMA API * tx/rx performance optimizations * use NAPI for tx cleanup on mt76x02 * AP mode support for USB devices * USB stability fixes * tx power handling fixes for 76x2 * endian fixes Conflicts: There's a trivial conflict in drivers/net/wireless/intel/iwlwifi/fw/file.h, just leave IWL_UCODE_TLV_FW_FSEQ_VERSION to the file. 'git diff' output should be just empty: diff --cc drivers/net/wireless/intel/iwlwifi/fw/file.h index cd622af90077,b0671e16e1ce..000000000000 --- a/drivers/net/wireless/intel/iwlwifi/fw/file.h +++ b/drivers/net/wireless/intel/iwlwifi/fw/file.h ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-27netlink: make validation more configurable for future strictnessJohannes Berg
We currently have two levels of strict validation: 1) liberal (default) - undefined (type >= max) & NLA_UNSPEC attributes accepted - attribute length >= expected accepted - garbage at end of message accepted 2) strict (opt-in) - NLA_UNSPEC attributes accepted - attribute length >= expected accepted Split out parsing strictness into four different options: * TRAILING - check that there's no trailing data after parsing attributes (in message or nested) * MAXTYPE - reject attrs > max known type * UNSPEC - reject attributes with NLA_UNSPEC policy entries * STRICT_ATTRS - strictly validate attribute size The default for future things should be *everything*. The current *_strict() is a combination of TRAILING and MAXTYPE, and is renamed to _deprecated_strict(). The current regular parsing has none of this, and is renamed to *_parse_deprecated(). Additionally it allows us to selectively set one of the new flags even on old policies. Notably, the UNSPEC flag could be useful in this case, since it can be arranged (by filling in the policy) to not be an incompatible userspace ABI change, but would then going forward prevent forgetting attribute entries. Similar can apply to the POLICY flag. We end up with the following renames: * nla_parse -> nla_parse_deprecated * nla_parse_strict -> nla_parse_deprecated_strict * nlmsg_parse -> nlmsg_parse_deprecated * nlmsg_parse_strict -> nlmsg_parse_deprecated_strict * nla_parse_nested -> nla_parse_nested_deprecated * nla_validate_nested -> nla_validate_nested_deprecated Using spatch, of course: @@ expression TB, MAX, HEAD, LEN, POL, EXT; @@ -nla_parse(TB, MAX, HEAD, LEN, POL, EXT) +nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT) @@ expression NLH, HDRLEN, TB, MAX, POL, EXT; @@ -nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT) +nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT) @@ expression NLH, HDRLEN, TB, MAX, POL, EXT; @@ -nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT) +nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT) @@ expression TB, MAX, NLA, POL, EXT; @@ -nla_parse_nested(TB, MAX, NLA, POL, EXT) +nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT) @@ expression START, MAX, POL, EXT; @@ -nla_validate_nested(START, MAX, POL, EXT) +nla_validate_nested_deprecated(START, MAX, POL, EXT) @@ expression NLH, HDRLEN, MAX, POL, EXT; @@ -nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT) +nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT) For this patch, don't actually add the strict, non-renamed versions yet so that it breaks compile if I get it wrong. Also, while at it, make nla_validate and nla_parse go down to a common __nla_validate_parse() function to avoid code duplication. Ultimately, this allows us to have very strict validation for every new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the next patch, while existing things will continue to work as is. In effect then, this adds fully strict validation for any new command. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-25wlcore: simplify/fix/optimize reg_ch_conf_pending operationsPaolo Bonzini
Bitmaps are defined on unsigned longs, so the usage of u32[2] in the wlcore driver is incorrect. As noted by Peter Zijlstra, casting arrays to a bitmap is incorrect for big-endian architectures. When looking at it I observed that: - operations on reg_ch_conf_pending is always under the wl_lock mutex, so set_bit is overkill - the only case where reg_ch_conf_pending is accessed a u32 at a time is unnecessary too. This patch cleans up everything in this area, and changes tmp_ch_bitmap to have the proper alignment. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Fenghua Yu <fenghua.yu@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-08Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
An ipvlan bug fix in 'net' conflicted with the abstraction away of the IPV6 specific support in 'net-next'. Similarly, a bug fix for mlx5 in 'net' conflicted with the flow action conversion in 'net-next'. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-01wl18xx: no need to check return value of debugfs_create functionsGreg Kroah-Hartman
When calling debugfs functions, there is no need to ever check the return value. The function can work or not, but the code logic should never do something different based on this. Cc: Kalle Valo <kvalo@codeaurora.org> Cc: Tony Lindgren <tony@atomide.com> Cc: linux-wireless@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-01wl12xx: no need to check return value of debugfs_create functionsGreg Kroah-Hartman
When calling debugfs functions, there is no need to ever check the return value. The function can work or not, but the code logic should never do something different based on this. Cc: Kalle Valo <kvalo@codeaurora.org> Cc: Tony Lindgren <tony@atomide.com> Cc: linux-wireless@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-01wl1251: no need to check return value of debugfs_create functionsGreg Kroah-Hartman
When calling debugfs functions, there is no need to ever check the return value. The function can work or not, but the code logic should never do something different based on this. Cc: Kalle Valo <kvalo@codeaurora.org> Cc: Tony Lindgren <tony@atomide.com> Cc: linux-wireless@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-01wlcore: no need to check return value of debugfs_create functionsGreg Kroah-Hartman
When calling debugfs functions, there is no need to ever check the return value. The function can work or not, but the code logic should never do something different based on this. Cc: Kalle Valo <kvalo@codeaurora.org> Cc: Tony Lindgren <tony@atomide.com> Cc: linux-wireless@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-01wlcore: clean up an indentation issueColin Ian King
There is a goto statement that is missing a tab for indentation. Fix this. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-01-22wlcore: sdio: Fixup power on/off sequenceUlf Hansson
During "wlan-up", we are programming the FW into the WiFi-chip. However, re-programming the FW doesn't work, unless a power cycle of the WiFi-chip is made in-between the programmings. To conform to this requirement and to fix the regression in a simple way, let's start by allowing that the SDIO card (WiFi-chip) may stay powered on (runtime resumed) when wl12xx_sdio_power_off() returns. The intent with the current code is to treat this scenario as an error, but unfortunate this doesn't work as expected, so let's fix this. The other part is to guarantee that a power cycle of the SDIO card has been completed when wl12xx_sdio_power_on() returns, as to allow the FW programming to succeed. However, relying solely on runtime PM to deal with this isn't sufficient. For example, userspace may prevent runtime suspend via sysfs for the device that represents the SDIO card, leading to that the mmc core also keeps it powered on. For this reason, let's instead do a brute force power cycle in wl12xx_sdio_power_on(). Fixes: 728a9dc61f13 ("wlcore: sdio: Fix flakey SDIO runtime PM handling") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Tony Lindgren <tony@atomide.com> Tested-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-01-10wlcore: Fix memory leak in case wl12xx_fetch_firmware failureZumeng Chen
Release fw_status, raw_fw_status, and tx_res_if when wl12xx_fetch_firmware failed instead of meaningless goto out to avoid the following memory leak reports(Only the last one listed): unreferenced object 0xc28a9a00 (size 512): comm "kworker/0:4", pid 31298, jiffies 2783204 (age 203.290s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<6624adab>] kmemleak_alloc+0x40/0x74 [<500ddb31>] kmem_cache_alloc_trace+0x1ac/0x270 [<db4d731d>] wl12xx_chip_wakeup+0xc4/0x1fc [wlcore] [<76c5db53>] wl1271_op_add_interface+0x4a4/0x8f4 [wlcore] [<cbf30777>] drv_add_interface+0xa4/0x1a0 [mac80211] [<65bac325>] ieee80211_reconfig+0x9c0/0x1644 [mac80211] [<2817c80e>] ieee80211_restart_work+0x90/0xc8 [mac80211] [<7e1d425a>] process_one_work+0x284/0x42c [<55f9432e>] worker_thread+0x2fc/0x48c [<abb582c6>] kthread+0x148/0x160 [<63144b13>] ret_from_fork+0x14/0x2c [< (null)>] (null) [<1f6e7715>] 0xffffffff Signed-off-by: Zumeng Chen <zumeng.chen@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-12-03Merge tag 'wireless-drivers-next-for-davem-2018-11-30' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for 4.21 First set of patches for 4.21. Most notable here is support for Quantenna's QSR1000/QSR2000 chipsets and more flexible ways to provide nvram files for brcmfmac. Major changes: brcmfmac * add support for first trying to get a board specific nvram file * add support for getting nvram contents from EFI variables qtnfmac * use single PCIe driver for all platforms and rename Kconfig option CONFIG_QTNFMAC_PEARL_PCIE to CONFIG_QTNFMAC_PCIE * add support for QSR1000/QSR2000 (Topaz) family of chipsets ath10k * add support for WCN3990 firmware crash recovery * add firmware memory dump support for QCA4019 wil6210 * add firmware error recovery while in AP mode ath9k * remove experimental notice from dynack feature iwlwifi * PCI IDs for some new 9000-series cards * improve antenna usage on connection problems * new firmware debugging infrastructure * some more work on 802.11ax * improve support for multiple RF modules with 22000 devices cordic * move cordic macros and defines to a public header file * convert brcmsmac and b43 to fully use cordic library ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-06wlcore: Fix the return value in case of error in ↵Christophe JAILLET
'wlcore_vendor_cmd_smart_config_start()' We return 0 unconditionally at the end of 'wlcore_vendor_cmd_smart_config_start()'. However, 'ret' is set to some error codes in several error handling paths and we already return some error codes at the beginning of the function. Return 'ret' instead to propagate the error code. Fixes: 80ff8063e87c ("wlcore: handle smart config vendor commands") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-11-06wlcore: Fixup "Add support for optional wakeirq"John Stultz
After commit 3c83dd577c7f ("wlcore: Add support for optional wakeirq") landed upstream, I started seeing the following oops on my HiKey board: [ 1.870279] Unable to handle kernel read from unreadable memory at virtual address 0000000000000010 [ 1.870283] Mem abort info: [ 1.870287] ESR = 0x96000005 [ 1.870292] Exception class = DABT (current EL), IL = 32 bits [ 1.870296] SET = 0, FnV = 0 [ 1.870299] EA = 0, S1PTW = 0 [ 1.870302] Data abort info: [ 1.870306] ISV = 0, ISS = 0x00000005 [ 1.870309] CM = 0, WnR = 0 [ 1.870312] [0000000000000010] user address but active_mm is swapper [ 1.870318] Internal error: Oops: 96000005 [#1] PREEMPT SMP [ 1.870327] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 4.19.0-05129-gb3d1e8e #48 [ 1.870331] Hardware name: HiKey Development Board (DT) [ 1.870350] Workqueue: events_freezable mmc_rescan [ 1.870358] pstate: 60400005 (nZCv daif +PAN -UAO) [ 1.870366] pc : wl1271_probe+0x210/0x350 [ 1.870371] lr : wl1271_probe+0x210/0x350 [ 1.870374] sp : ffffff80080739b0 [ 1.870377] x29: ffffff80080739b0 x28: 0000000000000000 [ 1.870384] x27: 0000000000000000 x26: 0000000000000000 [ 1.870391] x25: 0000000000000036 x24: ffffffc074ecb598 [ 1.870398] x23: ffffffc07ffdce78 x22: ffffffc0744ed808 [ 1.870404] x21: ffffffc074ecbb98 x20: ffffff8008ff9000 [ 1.870411] x19: ffffffc0744ed800 x18: ffffff8008ff9a48 [ 1.870418] x17: 0000000000000000 x16: 0000000000000000 [ 1.870425] x15: ffffffc074ecb503 x14: ffffffffffffffff [ 1.870431] x13: ffffffc074ecb502 x12: 0000000000000030 [ 1.870438] x11: 0101010101010101 x10: 0000000000000040 [ 1.870444] x9 : ffffffc075400248 x8 : ffffffc075400270 [ 1.870451] x7 : 0000000000000000 x6 : 0000000000000000 [ 1.870457] x5 : 0000000000000000 x4 : 0000000000000000 [ 1.870463] x3 : 0000000000000000 x2 : 0000000000000000 [ 1.870469] x1 : 0000000000000028 x0 : 0000000000000000 [ 1.870477] Process kworker/0:0 (pid: 5, stack limit = 0x(____ptrval____)) [ 1.870480] Call trace: [ 1.870485] wl1271_probe+0x210/0x350 [ 1.870491] sdio_bus_probe+0x100/0x128 [ 1.870500] really_probe+0x1a8/0x2b8 [ 1.870506] driver_probe_device+0x58/0x100 [ 1.870511] __device_attach_driver+0x94/0xd8 [ 1.870517] bus_for_each_drv+0x70/0xc8 [ 1.870522] __device_attach+0xe0/0x140 [ 1.870527] device_initial_probe+0x10/0x18 [ 1.870532] bus_probe_device+0x94/0xa0 [ 1.870537] device_add+0x374/0x5b8 [ 1.870542] sdio_add_func+0x60/0x88 [ 1.870546] mmc_attach_sdio+0x1b0/0x358 [ 1.870551] mmc_rescan+0x2cc/0x390 [ 1.870558] process_one_work+0x12c/0x320 [ 1.870563] worker_thread+0x48/0x458 [ 1.870569] kthread+0xf8/0x128 [ 1.870575] ret_from_fork+0x10/0x18 [ 1.870583] Code: 92400c21 b2760021 a90687a2 97e95bf9 (f9400803) [ 1.870587] ---[ end trace 1e15f81d3c139ca9 ]--- It seems since we don't have a wakeirq value in the dts, the wakeirq value in wl1271_probe() is zero, which then causes trouble in irqd_get_trigger_type(irq_get_irq_data(wakeirq)). This patch tries to address this by checking if wakeirq is zero, and not trying to add it to the resources if that is the case. Fixes: 3c83dd577c7f ("wlcore: Add support for optional wakeirq") Cc: Tony Lindgren <tony@atomide.com> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: Eyal Reizer <eyalr@ti.com> Cc: Anders Roxell <anders.roxell@linaro.org> Cc: linux-wireless@vger.kernel.org Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: John Stultz <john.stultz@linaro.org> Tested-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-10-05wlcore: Add support for optional wakeirqTony Lindgren
Now with wlcore using PM runtime, we can also add support for Linux generic wakeirq handling for it if configured in the dts file. The wakeirq can be configured as the second interrupt in the dts file with interrupts-extended property where it is the padconf irq of the OOB GPIO pin used for wlcore interrupt. Note that eventually we should also allow configuring wlcore to use the SDIO dat1 IRQ for wake-up, and in that case the the wakeirq should be configured to be the padconf interrupt of the dat1 pin and not the padconf interrupt of the OOB GPIO pin. Cc: Eyal Reizer <eyalr@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-10-05wlcore: Fix BUG with clear completion on timeoutTony Lindgren
We do not currently clear wl->elp_compl on ELP timeout and we have bogus lingering pointer that wlcore_irq then will try to access after recovery is done: BUG: spinlock bad magic on CPU#1, irq/255-wl12xx/580 ... (spin_dump) from [<c01b9344>] (do_raw_spin_lock+0xc8/0x124) (do_raw_spin_lock) from [<c09b3970>] (_raw_spin_lock_irqsave+0x68/0x74) (_raw_spin_lock_irqsave) from [<c01a02f0>] (complete+0x24/0x58) (complete) from [<bf572610>] (wlcore_irq+0x48/0x17c [wlcore]) (wlcore_irq [wlcore]) from [<c01c5efc>] (irq_thread_fn+0x2c/0x64) (irq_thread_fn) from [<c01c623c>] (irq_thread+0x148/0x290) (irq_thread) from [<c016b4b0>] (kthread+0x160/0x17c) (kthread) from [<c01010b4>] (ret_from_fork+0x14/0x20) ... After that the system will hang. Let's fix this by adding a flag for recovery and moving the recovery work call to to the error handling section. And we want to set WL1271_FLAG_INTENDED_FW_RECOVERY and actually clear it too in wl1271_recovery_work() and just downgrade the error to a warning to prevent overly verbose output. Cc: Eyal Reizer <eyalr@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-08-18Merge tag 'char-misc-4.19-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc driver updates from Greg KH: "Here is the bit set of char/misc drivers for 4.19-rc1 There is a lot here, much more than normal, seems like everyone is writing new driver subsystems these days... Anyway, major things here are: - new FSI driver subsystem, yet-another-powerpc low-level hardware bus - gnss, finally an in-kernel GPS subsystem to try to tame all of the crazy out-of-tree drivers that have been floating around for years, combined with some really hacky userspace implementations. This is only for GNSS receivers, but you have to start somewhere, and this is great to see. Other than that, there are new slimbus drivers, new coresight drivers, new fpga drivers, and loads of DT bindings for all of these and existing drivers. All of these have been in linux-next for a while with no reported issues" * tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits) android: binder: Rate-limit debug and userspace triggered err msgs fsi: sbefifo: Bump max command length fsi: scom: Fix NULL dereference misc: mic: SCIF Fix scif_get_new_port() error handling misc: cxl: changed asterisk position genwqe: card_base: Use true and false for boolean values misc: eeprom: assignment outside the if statement uio: potential double frees if __uio_register_device() fails eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency misc: ti-st: Fix memory leak in the error path of probe() android: binder: Show extra_buffers_size in trace firmware: vpd: Fix section enabled flag on vpd_section_destroy platform: goldfish: Retire pdev_bus goldfish: Use dedicated macros instead of manual bit shifting goldfish: Add missing includes to goldfish.h mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux dt-bindings: mux: add adi,adgs1408 Drivers: hv: vmbus: Cleanup synic memory free path Drivers: hv: vmbus: Remove use of slow_virt_to_phys() Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind() ...
2018-07-31wlcore: Set rx_status boottime_ns field on rxLoic Poulain
When receiving a beacon or probe response, we should update the boottime_ns field which is the timestamp the frame was received at. (cf mac80211.h) This fixes a scanning issue with Android since it relies on this timestamp to determine when the AP has been seen for the last time (via the nl80211 BSS_LAST_SEEN_BOOTTIME parameter). Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-07-31wlcore: remove duplicate \n for some warningsH. Nikolaus Schaller
wl1271_warning() already appends a \n to the format, so adding one to the warning string gives empty lines in the log. Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-07-07headers: separate linux/mod_devicetable.h from linux/platform_device.hRandy Dunlap
At over 4000 #includes, <linux/platform_device.h> is the 9th most #included header file in the Linux kernel. It does not need <linux/mod_devicetable.h>, so drop that header and explicitly add <linux/mod_devicetable.h> to source files that need it. 4146 #include <linux/platform_device.h> After this patch, there are 225 files that use <linux/mod_devicetable.h>, for a reduction of around 3900 times that <linux/mod_devicetable.h> does not have to be read & parsed. 225 #include <linux/mod_devicetable.h> This patch was build-tested on 20 different arch-es. It also makes these drivers SubmitChecklist#1 compliant. Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/ Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-04wlcore: Fix memory leak in wlcore_cmd_wait_for_event_or_timeoutGustavo A. R. Silva
In case memory resources for *events_vector* were allocated, release them before return. Addresses-Coverity-ID: 1470194 ("Resource leak") Fixes: 4ec7cece87b3 ("wlcore: Add missing PM call for wlcore_cmd_wait_for_event_or_timeout()") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-06-27wireless-drivers: use BIT_ULL for NL80211_STA_INFO_ attribute typesOmer Efrat
The BIT macro uses unsigned long which some architectures handle as 32 bit and therefore might cause macro's shift to overflow when used on a value equals or larger than 32 (NL80211_STA_INFO_RX_DURATION and afterwards). Since 'filled' member in station_info changed to u64, BIT_ULL macro should be used with all NL80211_STA_INFO_* attribute types instead of BIT to prevent future possible bugs when one will use BIT macro for higher attributes by mistake. This commit cleans up all usages of BIT macro with the above field in wireless-drivers by changing it to BIT_ULL instead. In addition, there are some places which don't use BIT nor BIT_ULL macros so align those as well. Signed-off-by: Omer Efrat <omer.efrat@tandemg.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-06-27wlcore: Enable runtime PM autosuspend supportTony Lindgren
With runtime PM tested working for wlcore with no autosuspend, we can now enable autosuspend to cut down on enable/disable for interrupts. Basically we just replace pm_runtime_put() with the autosuspend variants. Let's use autosuspend delay of 50ms that MMC drivers typically use. Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-06-27wlcore: Make sure firmware is initialized in wl1271_op_add_interface()Tony Lindgren
We have wl12xx_boot() call wl12xx_enable_interrupts() and if we have wl1271_op_add_interface() call pm_runtime_get_sync() before the interrupts are enabled. And then we get the following error during boot: wlcore: ERROR ELP wakeup timeout! Let's fix this by first checking if we need to boot the firmware. And only after that call pm_runtime_get_sync() when interrupts are enabled. And only after that do the check for wl12xx_need_fw_change(). Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-06-27wlcore: Use generic runtime pm calls for wowlan elp configurationEyal Reizer
With runtime PM enabled, we can now use calls to pm_runtime_force_suspend and pm_runtime_force_resume for enabling elp during suspend when wowlan is enabled and waking the chip from elp on resume. Remove the custom API that was used to ensure that the command that is used to allow ELP during suspend is completed before the system suspend. Signed-off-by: Eyal Reizer <eyalr@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-06-27wlcore: Fix timout errors after recoveryTony Lindgren
After enabling runtime PM, if we force hardware reset multiple times with: # echo 1 > /sys/kernel/debug/ieee80211/phy0/wlcore/start_recovery We will after few tries get the following error: wlcore: ERROR timeout waiting for the hardware to complete initialization And then wlcore is unable to reconnect until after the wlcore related modules are reloaded. Let's fix this by moving pm_runtime_put() earlier before we restart the hardware. And let's use the sync version to make sure we're done before we restart. Note that we still will get -EBUSY warning from wl12xx_sdio_set_power() but let's fix that separately once we know exactly why we get the warning. Reported-by: Eyal Reizer <eyalr@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-06-27wlcore: Fix misplaced PM call for scan_complete_work()Tony Lindgren
With runtime PM enabled, we now need to have wlcore enabled longer until after we're done calling wlcore_cmd_regdomain_config_locked(): scan_complete_work() wlcore_cmd_regdomain_config_locked() wlcore_cmd_send_failsafe() wl12xx_sdio_raw_read() Note that this is not needed before runtime PM support as the custom PM code had it's own timer. We have not yet enabled runtime PM autosuspend for wlcore and this is why this issue now shows up. Let's fix the issues first before we enable runtime PM autosuspend. Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-06-27wlcore: Add support for runtime PMTony Lindgren
We can update wlcore to use PM runtime by adding functions for wlcore_runtime_suspend() and wlcore_runtime_resume() and replacing calls to wl1271_ps_elp_wakeup() and wl1271_ps_elp_sleep() with calls to pm_runtime_get_sync() and pm_runtime_put(). Note that the new wlcore_runtime_suspend() and wlcore_runtime_resume() functions are based on simplified versions of wl1271_ps_elp_sleep() and wl1271_ps_elp_wakeup(). We don't want to use the old functions as we can now take advantage of the runtime PM usage count. And we don't need the old elp_work at all. And we can also remove WL1271_FLAG_ELP_REQUESTED that is no longer needed. Pretty much the only place where we are not just converting the existing functions is wl1271_op_suspend() where we add pm_runtime_put_noidle() to keep the calls paired. As the next step is to implement runtime PM autosuspend, let's not add wrapper functions for the generic runtime PM calls. We would be getting rid of any wrapper functions anyways. After autoidle we should be able to start using Linux generic wakeirqs for the padconf interrupt. Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-06-27wlcore: Make sure PM calls are pairedTony Lindgren
The call to wl1271_ps_elp_wakeup() in wl12xx_queue_recovery_work() is unpaired. Let's remove it and add paired calls to wl1271_recovery_work() instead in preparation for changing things to use runtime PM. Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-06-27wlcore: Add missing PM call for wlcore_cmd_wait_for_event_or_timeout()Tony Lindgren
Otherwise we can get: WARNING: CPU: 0 PID: 55 at drivers/net/wireless/ti/wlcore/io.h:84 I've only seen this few times with the runtime PM patches enabled so this one is probably not needed before that. This seems to work currently based on the current PM implementation timer. Let's apply this separately though in case others are hitting this issue. Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-29wlcore: sdio: check for valid platform device data before suspendEyal Reizer
the wl pointer can be null In case only wlcore_sdio is probed while no WiLink module is successfully probed, as in the case of mounting a wl12xx module while using a device tree file configured with wl18xx related settings. In this case the system was crashing in wl1271_suspend() as platform device data is not set. Make sure wl the pointer is valid before using it. Signed-off-by: Eyal Reizer <eyalr@ti.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
generated by cgit (git 2.34.1) at 2024-05-28 16:34:42 +0000