summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2021-08-19net: dpaa2-switch: disable the control interface on error pathVladimir Oltean
Currently dpaa2_switch_takedown has a funny name and does not do the opposite of dpaa2_switch_init, which makes probing fail when we need to handle an -EPROBE_DEFER. A sketch of what dpaa2_switch_init does: dpsw_open dpaa2_switch_detect_features dpsw_reset for (i = 0; i < ethsw->sw_attr.num_ifs; i++) { dpsw_if_disable dpsw_if_set_stp dpsw_vlan_remove_if_untagged dpsw_if_set_tci dpsw_vlan_remove_if } dpsw_vlan_remove alloc_ordered_workqueue dpsw_fdb_remove dpaa2_switch_ctrl_if_setup When dpaa2_switch_takedown is called from the error path of dpaa2_switch_probe(), the control interface, enabled by dpaa2_switch_ctrl_if_setup from dpaa2_switch_init, remains enabled, because dpaa2_switch_takedown does not call dpaa2_switch_ctrl_if_teardown. Since dpaa2_switch_probe might fail due to EPROBE_DEFER of a PHY, this means that a second probe of the driver will happen with the control interface directly enabled. This will trigger a second error: [ 93.273528] fsl_dpaa2_switch dpsw.0: dpsw_ctrl_if_set_pools() failed [ 93.281966] fsl_dpaa2_switch dpsw.0: fsl_mc_driver_probe failed: -13 [ 93.288323] fsl_dpaa2_switch: probe of dpsw.0 failed with error -13 Which if we investigate the /dev/dpaa2_mc_console log, we find out is caused by: [E, ctrl_if_set_pools:2211, DPMNG] ctrl_if must be disabled So make dpaa2_switch_takedown do the opposite of dpaa2_switch_init (in reasonable limits, no reason to change STP state, re-add VLANs etc), and rename it to something more conventional, like dpaa2_switch_teardown. Fixes: 613c0a5810b7 ("staging: dpaa2-switch: enable the control interface") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> Link: https://lore.kernel.org/r/20210819141755.1931423-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-19iavf: Fix ping is lost after untrusted VF had tried to change MACSylwester Dziedziuch
Make changes to MAC address dependent on the response of PF. Disallow changes to HW MAC address and MAC filter from untrusted VF, thanks to that ping is not lost if VF tries to change MAC. Add a new field in iavf_mac_filter, to indicate whether there was response from PF for given filter. Based on this field pass or discard the filter. If untrusted VF tried to change it's address, it's not changed. Still filter was changed, because of that ping couldn't go through. Fixes: c5c922b3e09b ("iavf: fix MAC address setting for VFs when filter is rejected") Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com> Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Gurucharan G <Gurucharanx.g@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-19i40e: Fix ATR queue selectionArkadiusz Kubalewski
Without this patch, ATR does not work. Receive/transmit uses queue selection based on SW DCB hashing method. If traffic classes are not configured for PF, then use netdev_pick_tx function for selecting queue for packet transmission. Instead of calling i40e_swdcb_skb_tx_hash, call netdev_pick_tx, which ensures that packet is transmitted/received from CPU that is running the application. Reproduction steps: 1. Load i40e driver 2. Map each MSI interrupt of i40e port for each CPU 3. Disable ntuple, enable ATR i.e.: ethtool -K $interface ntuple off ethtool --set-priv-flags $interface flow-director-atr 4. Run application that is generating traffic and is bound to a single CPU, i.e.: taskset -c 9 netperf -H 1.1.1.1 -t TCP_RR -l 10 5. Observe behavior: Application's traffic should be restricted to the CPU provided in taskset. Fixes: 89ec1f0886c1 ("i40e: Fix queue-to-TC mapping on Tx") Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com> Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Tested-by: Dave Switzer <david.switzer@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-19r8152: fix the maximum number of PLA bp for RTL8153CHayes Wang
The maximum PLA bp number of RTL8153C is 16, not 8. That is, the bp 0 ~ 15 are at 0xfc28 ~ 0xfc46, and the bp_en is at 0xfc48. Fixes: 195aae321c82 ("r8152: support new chips") Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-19r8152: fix writing USB_BP2_ENHayes Wang
The register of USB_BP2_EN is 16 bits, so we should use ocp_write_word(), not ocp_write_byte(). Fixes: 9370f2d05a2a ("support request_firmware for RTL8153") Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-18net: mscc: ocelot: allow forwarding from bridge ports to the tag_8021q CPU portVladimir Oltean
Currently we are unable to ping a bridge on top of a felix switch which uses the ocelot-8021q tagger. The packets are dropped on the ingress of the user port and the 'drop_local' counter increments (the counter which denotes drops due to no valid destinations). Dumping the PGID tables, it becomes clear that the PGID_SRC of the user port is zero, so it has no valid destinations. But looking at the code, the cpu_fwd_mask (the bit mask of DSA tag_8021q ports) is clearly missing from the forwarding mask of ports that are under a bridge. So this has always been broken. Looking at the version history of the patch, in v7 https://patchwork.kernel.org/project/netdevbpf/patch/20210125220333.1004365-12-olteanv@gmail.com/ the code looked like this: /* Standalone ports forward only to DSA tag_8021q CPU ports */ unsigned long mask = cpu_fwd_mask; (...) } else if (ocelot->bridge_fwd_mask & BIT(port)) { mask |= ocelot->bridge_fwd_mask & ~BIT(port); while in v8 (the merged version) https://patchwork.kernel.org/project/netdevbpf/patch/20210129010009.3959398-12-olteanv@gmail.com/ it looked like this: unsigned long mask; (...) } else if (ocelot->bridge_fwd_mask & BIT(port)) { mask = ocelot->bridge_fwd_mask & ~BIT(port); So the breakage was introduced between v7 and v8 of the patch. Fixes: e21268efbe26 ("net: dsa: felix: perform switch setup for tag_8021q") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20210817160425.3702809-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-18net: asix: fix uninit value bugsPavel Skripkin
Syzbot reported uninit-value in asix_mdio_read(). The problem was in missing error handling. asix_read_cmd() should initialize passed stack variable smsr, but it can fail in some cases. Then while condidition checks possibly uninit smsr variable. Since smsr is uninitialized stack variable, driver can misbehave, because smsr will be random in case of asix_read_cmd() failure. Fix it by adding error handling and just continue the loop instead of checking uninit value. Added helper function for checking Host_En bit, since wrong loop was used in 4 functions and there is no need in copy-pasting code parts. Cc: Robert Foss <robert.foss@collabora.com> Fixes: d9fe64e51114 ("net: asix: Add in_pm parameter") Reported-by: syzbot+a631ec9e717fb0423053@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-18net: mdio-mux: Handle -EPROBE_DEFER correctlySaravana Kannan
When registering mdiobus children, if we get an -EPROBE_DEFER, we shouldn't ignore it and continue registering the rest of the mdiobus children. This would permanently prevent the deferring child mdiobus from working instead of reattempting it in the future. So, if a child mdiobus needs to be reattempted in the future, defer the entire mdio-mux initialization. This fixes the issue where PHYs sitting under the mdio-mux aren't initialized correctly if the PHY's interrupt controller is not yet ready when the mdio-mux is being probed. Additional context in the link below. Fixes: 0ca2997d1452 ("netdev/of/phy: Add MDIO bus multiplexer support.") Link: https://lore.kernel.org/lkml/CAGETcx95kHrv8wA-O+-JtfH7H9biJEGJtijuPVN0V5dUKUAB3A@mail.gmail.com/#t Signed-off-by: Saravana Kannan <saravanak@google.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Marc Zyngier <maz@kernel.org> Tested-by: Marc Zyngier <maz@kernel.org> Acked-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-18net: mdio-mux: Don't ignore memory allocation errorsSaravana Kannan
If we are seeing memory allocation errors, don't try to continue registering child mdiobus devices. It's unlikely they'll succeed. Fixes: 342fa1964439 ("mdio: mux: make child bus walking more permissive and errors more verbose") Signed-off-by: Saravana Kannan <saravanak@google.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Marc Zyngier <maz@kernel.org> Tested-by: Marc Zyngier <maz@kernel.org> Acked-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-18net: mdio-mux: Delete unnecessary devm_kfreeSaravana Kannan
The whole point of devm_* APIs is that you don't have to undo them if you are returning an error that's going to get propagated out of a probe() function. So delete unnecessary devm_kfree() call in the error return path. Fixes: b60161668199 ("mdio: mux: Correct mdio_mux_init error path issues") Signed-off-by: Saravana Kannan <saravanak@google.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Marc Zyngier <maz@kernel.org> Tested-by: Marc Zyngier <maz@kernel.org> Acked-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-18net: dsa: sja1105: fix use-after-free after calling of_find_compatible_node, ↵Vladimir Oltean
or worse It seems that of_find_compatible_node has a weird calling convention in which it calls of_node_put() on the "from" node argument, instead of leaving that up to the caller. This comes from the fact that of_find_compatible_node with a non-NULL "from" argument it only supposed to be used as the iterator function of for_each_compatible_node(). OF iterator functions call of_node_get on the next OF node and of_node_put() on the previous one. When of_find_compatible_node calls of_node_put, it actually never expects the refcount to drop to zero, because the call is done under the atomic devtree_lock context, and when the refcount drops to zero it triggers a kobject and a sysfs file deletion, which assume blocking context. So any driver call to of_find_compatible_node is probably buggy because an unexpected of_node_put() takes place. What should be done is to use the of_get_compatible_child() function. Fixes: 5a8f09748ee7 ("net: dsa: sja1105: register the MDIO buses for 100base-T1 and 100base-TX") Link: https://lore.kernel.org/netdev/20210814010139.kzryimmp4rizlznt@skbuf/ Suggested-by: Frank Rowand <frowand.list@gmail.com> Suggested-by: Rob Herring <robh+dt@kernel.org> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-17ixgbe, xsk: clean up the resources in ixgbe_xsk_pool_enable error pathWang Hai
In ixgbe_xsk_pool_enable(), if ixgbe_xsk_wakeup() fails, We should restore the previous state and clean up the resources. Add the missing clear af_xdp_zc_qps and unmap dma to fix this bug. Fixes: d49e286d354e ("ixgbe: add tracking of AF_XDP zero-copy state for each queue pair") Fixes: 4a9b32f30f80 ("ixgbe: fix potential RX buffer starvation for AF_XDP") Signed-off-by: Wang Hai <wanghai38@huawei.com> Acked-by: Magnus Karlsson <magnus.karlsson@intel.com> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20210817203736.3529939-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-17Merge tag 'wireless-drivers-2021-08-17' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers Kalle Valo says: ==================== wireless-drivers fixes for v5.14 First set of fixes for v5.14 and nothing major this time. New devices for iwlwifi and one fix for a compiler warning. iwlwifi * support for new devices mt76 * fix compiler warning about MT_CIPHER_NONE * tag 'wireless-drivers-2021-08-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers: mt76: fix enum type mismatch iwlwifi: add new so-jf devices iwlwifi: add new SoF with JF devices iwlwifi: pnvm: accept multiple HW-type TLVs ==================== Link: https://lore.kernel.org/r/20210817171027.EC1E6C43460@smtp.codeaurora.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-17net: qlcnic: add missed unlock in qlcnic_83xx_flash_read32Dinghao Liu
qlcnic_83xx_unlock_flash() is called on all paths after we call qlcnic_83xx_lock_flash(), except for one error path on failure of QLCRD32(), which may cause a deadlock. This bug is suggested by a static analysis tool, please advise. Fixes: 81d0aeb0a4fff ("qlcnic: flash template based firmware reset recovery") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Link: https://lore.kernel.org/r/20210816131405.24024-1-dinghao.liu@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-17virtio-net: use NETIF_F_GRO_HW instead of NETIF_F_LROJason Wang
Commit a02e8964eaf92 ("virtio-net: ethtool configurable LRO") maps LRO to virtio guest offloading features and allows the administrator to enable and disable those features via ethtool. This leads to several issues: - For a device that doesn't support control guest offloads, the "LRO" can't be disabled triggering WARN in dev_disable_lro() when turning off LRO or when enabling forwarding bridging etc. - For a device that supports control guest offloads, the guest offloads are disabled in cases of bridging, forwarding etc slowing down the traffic. Fix this by using NETIF_F_GRO_HW instead. Though the spec does not guarantee packets to be re-segmented as the original ones, we can add that to the spec, possibly with a flag for devices to differentiate between GRO and LRO. Further, we never advertised LRO historically before a02e8964eaf92 ("virtio-net: ethtool configurable LRO") and so bridged/forwarded configs effectively always relied on virtio receive offloads behaving like GRO - thus even if this breaks any configs it is at least not a regression. Fixes: a02e8964eaf92 ("virtio-net: ethtool configurable LRO") Acked-by: Michael S. Tsirkin <mst@redhat.com> Reported-by: Ivan <ivan@prestigetransportation.com> Tested-by: Ivan <ivan@prestigetransportation.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-16vrf: Reset skb conntrack connection on VRF rcvLahav Schlesinger
To fix the "reverse-NAT" for replies. When a packet is sent over a VRF, the POST_ROUTING hooks are called twice: Once from the VRF interface, and once from the "actual" interface the packet will be sent from: 1) First SNAT: l3mdev_l3_out() -> vrf_l3_out() -> .. -> vrf_output_direct() This causes the POST_ROUTING hooks to run. 2) Second SNAT: 'ip_output()' calls POST_ROUTING hooks again. Similarly for replies, first ip_rcv() calls PRE_ROUTING hooks, and second vrf_l3_rcv() calls them again. As an example, consider the following SNAT rule: > iptables -t nat -A POSTROUTING -p udp -m udp --dport 53 -j SNAT --to-source 2.2.2.2 -o vrf_1 In this case sending over a VRF will create 2 conntrack entries. The first is from the VRF interface, which performs the IP SNAT. The second will run the SNAT, but since the "expected reply" will remain the same, conntrack randomizes the source port of the packet: e..g With a socket bound to 1.1.1.1:10000, sending to 3.3.3.3:53, the conntrack rules are: udp 17 29 src=2.2.2.2 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 [UNREPLIED] src=3.3.3.3 dst=2.2.2.2 sport=53 dport=61033 packets=0 bytes=0 mark=0 use=1 udp 17 29 src=1.1.1.1 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 [UNREPLIED] src=3.3.3.3 dst=2.2.2.2 sport=53 dport=10000 packets=0 bytes=0 mark=0 use=1 i.e. First SNAT IP from 1.1.1.1 --> 2.2.2.2, and second the src port is SNAT-ed from 10000 --> 61033. But when a reply is sent (3.3.3.3:53 -> 2.2.2.2:61033) only the later conntrack entry is matched: udp 17 29 src=2.2.2.2 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 src=3.3.3.3 dst=2.2.2.2 sport=53 dport=61033 packets=1 bytes=49 mark=0 use=1 udp 17 28 src=1.1.1.1 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 [UNREPLIED] src=3.3.3.3 dst=2.2.2.2 sport=53 dport=10000 packets=0 bytes=0 mark=0 use=1 And a "port 61033 unreachable" ICMP packet is sent back. The issue is that when PRE_ROUTING hooks are called from vrf_l3_rcv(), the skb already has a conntrack flow attached to it, which means nf_conntrack_in() will not resolve the flow again. This means only the dest port is "reverse-NATed" (61033 -> 10000) but the dest IP remains 2.2.2.2, and since the socket is bound to 1.1.1.1 it's not received. This can be verified by logging the 4-tuple of the packet in '__udp4_lib_rcv()'. The fix is then to reset the flow when skb is received on a VRF, to let conntrack resolve the flow again (which now will hit the earlier flow). To reproduce: (Without the fix "Got pkt_to_nat_port" will not be printed by running 'bash ./repro'): $ cat run_in_A1.py import logging logging.getLogger("scapy.runtime").setLevel(logging.ERROR) from scapy.all import * import argparse def get_packet_to_send(udp_dst_port, msg_name): return Ether(src='11:22:33:44:55:66', dst=iface_mac)/ \ IP(src='3.3.3.3', dst='2.2.2.2')/ \ UDP(sport=53, dport=udp_dst_port)/ \ Raw(f'{msg_name}\x0012345678901234567890') parser = argparse.ArgumentParser() parser.add_argument('-iface_mac', dest="iface_mac", type=str, required=True, help="From run_in_A3.py") parser.add_argument('-socket_port', dest="socket_port", type=str, required=True, help="From run_in_A3.py") parser.add_argument('-v1_mac', dest="v1_mac", type=str, required=True, help="From script") args, _ = parser.parse_known_args() iface_mac = args.iface_mac socket_port = int(args.socket_port) v1_mac = args.v1_mac print(f'Source port before NAT: {socket_port}') while True: pkts = sniff(iface='_v0', store=True, count=1, timeout=10) if 0 == len(pkts): print('Something failed, rerun the script :(', flush=True) break pkt = pkts[0] if not pkt.haslayer('UDP'): continue pkt_sport = pkt.getlayer('UDP').sport print(f'Source port after NAT: {pkt_sport}', flush=True) pkt_to_send = get_packet_to_send(pkt_sport, 'pkt_to_nat_port') sendp(pkt_to_send, '_v0', verbose=False) # Will not be received pkt_to_send = get_packet_to_send(socket_port, 'pkt_to_socket_port') sendp(pkt_to_send, '_v0', verbose=False) break $ cat run_in_A2.py import socket import netifaces print(f"{netifaces.ifaddresses('e00000')[netifaces.AF_LINK][0]['addr']}", flush=True) s = socket.socket(socket.AF_INET, socket.SOCK_DGRAM) s.setsockopt(socket.SOL_SOCKET, socket.SO_BINDTODEVICE, str('vrf_1' + '\0').encode('utf-8')) s.connect(('3.3.3.3', 53)) print(f'{s. getsockname()[1]}', flush=True) s.settimeout(5) while True: try: # Periodically send in order to keep the conntrack entry alive. s.send(b'a'*40) resp = s.recvfrom(1024) msg_name = resp[0].decode('utf-8').split('\0')[0] print(f"Got {msg_name}", flush=True) except Exception as e: pass $ cat repro.sh ip netns del A1 2> /dev/null ip netns del A2 2> /dev/null ip netns add A1 ip netns add A2 ip -n A1 link add _v0 type veth peer name _v1 netns A2 ip -n A1 link set _v0 up ip -n A2 link add e00000 type bond ip -n A2 link add lo0 type dummy ip -n A2 link add vrf_1 type vrf table 10001 ip -n A2 link set vrf_1 up ip -n A2 link set e00000 master vrf_1 ip -n A2 addr add 1.1.1.1/24 dev e00000 ip -n A2 link set e00000 up ip -n A2 link set _v1 master e00000 ip -n A2 link set _v1 up ip -n A2 link set lo0 up ip -n A2 addr add 2.2.2.2/32 dev lo0 ip -n A2 neigh add 1.1.1.10 lladdr 77:77:77:77:77:77 dev e00000 ip -n A2 route add 3.3.3.3/32 via 1.1.1.10 dev e00000 table 10001 ip netns exec A2 iptables -t nat -A POSTROUTING -p udp -m udp --dport 53 -j \ SNAT --to-source 2.2.2.2 -o vrf_1 sleep 5 ip netns exec A2 python3 run_in_A2.py > x & XPID=$! sleep 5 IFACE_MAC=`sed -n 1p x` SOCKET_PORT=`sed -n 2p x` V1_MAC=`ip -n A2 link show _v1 | sed -n 2p | awk '{print $2'}` ip netns exec A1 python3 run_in_A1.py -iface_mac ${IFACE_MAC} -socket_port \ ${SOCKET_PORT} -v1_mac ${SOCKET_PORT} sleep 5 kill -9 $XPID wait $XPID 2> /dev/null ip netns del A1 ip netns del A2 tail x -n 2 rm x set +x Fixes: 73e20b761acf ("net: vrf: Add support for PREROUTING rules on vrf device") Signed-off-by: Lahav Schlesinger <lschlesinger@drivenets.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20210815120002.2787653-1-lschlesinger@drivenets.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-16net: iosm: Prevent underflow in ipc_chnl_cfg_get()Dan Carpenter
The bounds check on "index" doesn't catch negative values. Using ARRAY_SIZE() directly is more readable and more robust because it prevents negative values for "index". Fortunately we only pass valid values to ipc_chnl_cfg_get() so this patch does not affect runtime. Reported-by: Solomon Ucko <solly.ucko@gmail.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: M Chetan Kumar <m.chetan.kumar@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-16bnxt_en: Add missing DMA memory barriersMichael Chan
Each completion ring entry has a valid bit to indicate that the entry contains a valid completion event. The driver's main poll loop __bnxt_poll_work() has the proper dma_rmb() to make sure the valid bit of the next entry has been checked before proceeding further. But when we call bnxt_rx_pkt() to process the RX event, the RX completion event consists of two completion entries and only the first entry has been checked to be valid. We need the same barrier after checking the next completion entry. Add missing dma_rmb() barriers in bnxt_rx_pkt() and other similar locations. Fixes: 67a95e2022c7 ("bnxt_en: Need memory barrier when processing the completion ring.") Reported-by: Lance Richardson <lance.richardson@broadcom.com> Reviewed-by: Andy Gospodarek <gospo@broadcom.com> Reviewed-by: Lance Richardson <lance.richardson@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-16bnxt_en: Disable aRFS if running on 212 firmwareMichael Chan
212 firmware broke aRFS, so disable it. Traffic may stop after ntuple filters are inserted and deleted by the 212 firmware. Fixes: ae10ae740ad2 ("bnxt_en: Add new hardware RFS mode.") Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-16qed: Fix null-pointer dereference in qed_rdma_create_qp()Shai Malin
Fix a possible null-pointer dereference in qed_rdma_create_qp(). Changes from V2: - Revert checkpatch fixes. Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: Shai Malin <smalin@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-16qed: qed ll2 race condition fixesShai Malin
Avoiding qed ll2 race condition and NULL pointer dereference as part of the remove and recovery flows. Changes form V1: - Change (!p_rx->set_prod_addr). - qed_ll2.c checkpatch fixes. Change from V2: - Revert "qed_ll2.c checkpatch fixes". Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: Shai Malin <smalin@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-16net: 6pack: fix slab-out-of-bounds in decode_dataPavel Skripkin
Syzbot reported slab-out-of bounds write in decode_data(). The problem was in missing validation checks. Syzbot's reproducer generated malicious input, which caused decode_data() to be called a lot in sixpack_decode(). Since rx_count_cooked is only 400 bytes and noone reported before, that 400 bytes is not enough, let's just check if input is malicious and complain about buffer overrun. Fail log: ================================================================== BUG: KASAN: slab-out-of-bounds in drivers/net/hamradio/6pack.c:843 Write of size 1 at addr ffff888087c5544e by task kworker/u4:0/7 CPU: 0 PID: 7 Comm: kworker/u4:0 Not tainted 5.6.0-rc3-syzkaller #0 ... Workqueue: events_unbound flush_to_ldisc Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x197/0x210 lib/dump_stack.c:118 print_address_description.constprop.0.cold+0xd4/0x30b mm/kasan/report.c:374 __kasan_report.cold+0x1b/0x32 mm/kasan/report.c:506 kasan_report+0x12/0x20 mm/kasan/common.c:641 __asan_report_store1_noabort+0x17/0x20 mm/kasan/generic_report.c:137 decode_data.part.0+0x23b/0x270 drivers/net/hamradio/6pack.c:843 decode_data drivers/net/hamradio/6pack.c:965 [inline] sixpack_decode drivers/net/hamradio/6pack.c:968 [inline] Reported-and-tested-by: syzbot+fc8cd9a673d4577fb2e4@syzkaller.appspotmail.com Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-13ice: Fix perout start time roundingMaciej Machnikowski
Internal tests found out that the latest code doesn't bring up 1PPS out as expected. As a result of incorrect define used to round the time up the time was round down to the past second boundary. Fix define used for rounding to properly round up to the next Top of second in ice_ptp_cfg_clkout to fix it. Fixes: 172db5f91d5f ("ice: add support for auxiliary input/output pins") Signed-off-by: Maciej Machnikowski <maciej.machnikowski@intel.com> Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20210813165018.2196013-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-13bnxt: count Tx dropsJakub Kicinski
Drivers should count packets they are dropping. Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.") Reviewed-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-13bnxt: make sure xmit_more + errors does not miss doorbellsJakub Kicinski
skbs are freed on error and not put on the ring. We may, however, be in a situation where we're freeing the last skb of a batch, and there is a doorbell ring pending because of xmit_more() being true earlier. Make sure we ring the door bell in such situations. Since errors are rare don't pay attention to xmit_more() and just always flush the pending frames. The busy case should be safe to be left alone because it can only happen if start_xmit races with completions and they both enable the queue. In that case the kick can't be pending. Noticed while reading the code. Fixes: 4d172f21cefe ("bnxt_en: Implement xmit_more.") Reviewed-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-13bnxt: disable napi before canceling DIMJakub Kicinski
napi schedules DIM, napi has to be disabled first, then DIM canceled. Noticed while reading the code. Fixes: 0bc0b97fca73 ("bnxt_en: cleanup DIM work on device shutdown") Fixes: 6a8788f25625 ("bnxt_en: add support for software dynamic interrupt moderation") Reviewed-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-13bnxt: don't lock the tx queue from napi pollJakub Kicinski
We can't take the tx lock from the napi poll routine, because netpoll can poll napi at any moment, including with the tx lock already held. The tx lock is protecting against two paths - the disable path, and (as Michael points out) the NETDEV_TX_BUSY case which may occur if NAPI completions race with start_xmit and both decide to re-enable the queue. For the disable/ifdown path use synchronize_net() to make sure closing the device does not race we restarting the queues. Annotate accesses to dev_state against data races. For the NAPI cleanup vs start_xmit path - appropriate barriers are already in place in the main spot where Tx queue is stopped but we need to do the same careful dance in the TX_BUSY case. Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.") Reviewed-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-12Merge tag 'ieee802154-for-davem-2021-08-12' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan Stefan Schmidt says: ==================== ieee802154 for net 2021-08-12 Mostly fixes coming from bot reports. Dongliang Mu tackled some syzkaller reports in hwsim again and Takeshi Misawa a memory leak in ieee802154 raw. * tag 'ieee802154-for-davem-2021-08-12' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan: net: Fix memory leak in ieee802154_raw_deliver ieee802154: hwsim: fix GPF in hwsim_new_edge_nl ieee802154: hwsim: fix GPF in hwsim_set_edge_lqi ==================== Link: https://lore.kernel.org/r/20210812183912.1663996-1-stefan@datenfreihafen.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-12wwan: core: Avoid returning NULL from wwan_create_dev()Andy Shevchenko
Make wwan_create_dev() to return either valid or error pointer, In some cases it may return NULL. Prevent this by converting it to the respective error pointer. Fixes: 9a44c1cc6388 ("net: Add a WWAN subsystem") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Reviewed-by: Loic Poulain <loic.poulain@linaro.org> Link: https://lore.kernel.org/r/20210811124845.10955-1-andriy.shevchenko@linux.intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-12net: dsa: sja1105: unregister the MDIO buses during teardownVladimir Oltean
The call to sja1105_mdiobus_unregister is present in the error path but absent from the main driver unbind path. Fixes: 5a8f09748ee7 ("net: dsa: sja1105: register the MDIO buses for 100base-T1 and 100base-TX") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-12net: mscc: Fix non-GPL export of regmap APIsMark Brown
The ocelot driver makes use of regmap, wrapping it with driver specific operations that are thin wrappers around the core regmap APIs. These are exported with EXPORT_SYMBOL, dropping the _GPL from the core regmap exports which is frowned upon. Add _GPL suffixes to at least the APIs that are doing register I/O. Signed-off-by: Mark Brown <broonie@kernel.org> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-11net: pcs: xpcs: fix error handling on failed to allocate memoryWong Vee Khee
Drivers such as sja1105 and stmmac that call xpcs_create() expects an error returned by the pcs-xpcs module, but this was not the case on failed to allocate memory. Fixed this by returning an -ENOMEM instead of a NULL pointer. Fixes: 3ad1d171548e ("net: dsa: sja1105: migrate to xpcs for SGMII") Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20210810085812.1808466-1-vee.khee.wong@linux.intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-10net: switchdev: zero-initialize struct switchdev_notifier_fdb_info emitted ↵Vladimir Oltean
by drivers towards the bridge The blamed commit added a new field to struct switchdev_notifier_fdb_info, but did not make sure that all call paths set it to something valid. For example, a switchdev driver may emit a SWITCHDEV_FDB_ADD_TO_BRIDGE notifier, and since the 'is_local' flag is not set, it contains junk from the stack, so the bridge might interpret those notifications as being for local FDB entries when that was not intended. To avoid that now and in the future, zero-initialize all switchdev_notifier_fdb_info structures created by drivers such that all newly added fields to not need to touch drivers again. Fixes: 2c4eca3ef716 ("net: bridge: switchdev: include local flag in FDB notifications") Reported-by: Ido Schimmel <idosch@idosch.org> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Reviewed-by: Karsten Graul <kgraul@linux.ibm.com> Link: https://lore.kernel.org/r/20210810115024.1629983-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-10net: dsa: sja1105: fix broken backpressure in .port_fdb_dumpVladimir Oltean
rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into multiple netlink skbs if the buffer provided by user space is too small (one buffer will typically handle a few hundred FDB entries). When the current buffer becomes full, nlmsg_put() in dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that point, and then the dump resumes on the same port with a new skb, and FDB entries up to the saved index are simply skipped. Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to drivers, then drivers must check for the -EMSGSIZE error code returned by it. Otherwise, when a netlink skb becomes full, DSA will no longer save newly dumped FDB entries to it, but the driver will continue dumping. So FDB entries will be missing from the dump. Fix the broken backpressure by propagating the "cb" return code and allow rtnl_fdb_dump() to restart the FDB dump with a new skb. Fixes: 291d1e72b756 ("net: dsa: sja1105: Add support for FDB and MDB management") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-10net: dsa: lantiq: fix broken backpressure in .port_fdb_dumpVladimir Oltean
rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into multiple netlink skbs if the buffer provided by user space is too small (one buffer will typically handle a few hundred FDB entries). When the current buffer becomes full, nlmsg_put() in dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that point, and then the dump resumes on the same port with a new skb, and FDB entries up to the saved index are simply skipped. Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to drivers, then drivers must check for the -EMSGSIZE error code returned by it. Otherwise, when a netlink skb becomes full, DSA will no longer save newly dumped FDB entries to it, but the driver will continue dumping. So FDB entries will be missing from the dump. Fix the broken backpressure by propagating the "cb" return code and allow rtnl_fdb_dump() to restart the FDB dump with a new skb. Fixes: 58c59ef9e930 ("net: dsa: lantiq: Add Forwarding Database access") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-10net: dsa: lan9303: fix broken backpressure in .port_fdb_dumpVladimir Oltean
rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into multiple netlink skbs if the buffer provided by user space is too small (one buffer will typically handle a few hundred FDB entries). When the current buffer becomes full, nlmsg_put() in dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that point, and then the dump resumes on the same port with a new skb, and FDB entries up to the saved index are simply skipped. Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to drivers, then drivers must check for the -EMSGSIZE error code returned by it. Otherwise, when a netlink skb becomes full, DSA will no longer save newly dumped FDB entries to it, but the driver will continue dumping. So FDB entries will be missing from the dump. Fix the broken backpressure by propagating the "cb" return code and allow rtnl_fdb_dump() to restart the FDB dump with a new skb. Fixes: ab335349b852 ("net: dsa: lan9303: Add port_fast_age and port_fdb_dump methods") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-10net: dsa: hellcreek: fix broken backpressure in .port_fdb_dumpVladimir Oltean
rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into multiple netlink skbs if the buffer provided by user space is too small (one buffer will typically handle a few hundred FDB entries). When the current buffer becomes full, nlmsg_put() in dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that point, and then the dump resumes on the same port with a new skb, and FDB entries up to the saved index are simply skipped. Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to drivers, then drivers must check for the -EMSGSIZE error code returned by it. Otherwise, when a netlink skb becomes full, DSA will no longer save newly dumped FDB entries to it, but the driver will continue dumping. So FDB entries will be missing from the dump. Fix the broken backpressure by propagating the "cb" return code and allow rtnl_fdb_dump() to restart the FDB dump with a new skb. Fixes: e4b27ebc780f ("net: dsa: Add DSA driver for Hirschmann Hellcreek switches") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Kurt Kanzenbach <kurt@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-10net: dsa: microchip: ksz8795: Don't use phy_port_cnt in VLAN table lookupBen Hutchings
The magic number 4 in VLAN table lookup was the number of entries we can read and write at once. Using phy_port_cnt here doesn't make sense and presumably broke VLAN filtering for 3-port switches. Change it back to 4. Fixes: 4ce2a984abd8 ("net: dsa: microchip: ksz8795: use phy_port_cnt ...") Signed-off-by: Ben Hutchings <ben.hutchings@mind.be> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-10net: dsa: microchip: ksz8795: Fix VLAN filteringBen Hutchings
Currently ksz8_port_vlan_filtering() sets or clears the VLAN Enable hardware flag. That controls discarding of packets with a VID that has not been enabled for any port on the switch. Since it is a global flag, set the dsa_switch::vlan_filtering_is_global flag so that the DSA core understands this can't be controlled per port. When VLAN filtering is enabled, the switch should also discard packets with a VID that's not enabled on the ingress port. Set or clear each external port's VLAN Ingress Filter flag in ksz8_port_vlan_filtering() to make that happen. Fixes: e66f840c08a2 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver") Signed-off-by: Ben Hutchings <ben.hutchings@mind.be> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-10net: dsa: microchip: ksz8795: Use software untagging on CPU portBen Hutchings
On the CPU port, we can support both tagged and untagged VLANs at the same time by doing any necessary untagging in software rather than hardware. To enable that, keep the CPU port's Remove Tag flag cleared and set the dsa_switch::untag_bridge_pvid flag. Fixes: e66f840c08a2 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver") Signed-off-by: Ben Hutchings <ben.hutchings@mind.be> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-10net: dsa: microchip: ksz8795: Fix VLAN untagged flag change on deletionBen Hutchings
When a VLAN is deleted from a port, the flags in struct switchdev_obj_port_vlan are always 0. ksz8_port_vlan_del() copies the BRIDGE_VLAN_INFO_UNTAGGED flag to the port's Tag Removal flag, and therefore always clears it. In case there are multiple VLANs configured as untagged on this port - which seems useless, but is allowed - deleting one of them changes the remaining VLANs to be tagged. It's only ever necessary to change this flag when a VLAN is added to the port, so leave it unchanged in ksz8_port_vlan_del(). Fixes: e66f840c08a2 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver") Signed-off-by: Ben Hutchings <ben.hutchings@mind.be> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-10net: dsa: microchip: ksz8795: Reject unsupported VLAN configurationBen Hutchings
The switches supported by ksz8795 only have a per-port flag for Tag Removal. This means it is not possible to support both tagged and untagged VLANs on the same port. Reject attempts to add a VLAN that requires the flag to be changed, unless there are no VLANs currently configured. VID 0 is excluded from this check since it is untagged regardless of the state of the flag. On the CPU port we could support tagged and untagged VLANs at the same time. This will be enabled by a later patch. Fixes: e66f840c08a2 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver") Signed-off-by: Ben Hutchings <ben.hutchings@mind.be> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-10net: dsa: microchip: ksz8795: Fix PVID tag insertionBen Hutchings
ksz8795 has never actually enabled PVID tag insertion, and it also programmed the PVID incorrectly. To fix this: * Allow tag insertion to be controlled per ingress port. On most chips, set bit 2 in Global Control 19. On KSZ88x3 this control flag doesn't exist. * When adding a PVID: - Set the appropriate register bits to enable tag insertion on egress at every other port if this was the packet's ingress port. - Mask *out* the VID from the default tag, before or-ing in the new PVID. * When removing a PVID: - Clear the same control bits to disable tag insertion. - Don't update the default tag. This wasn't doing anything useful. Fixes: e66f840c08a2 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver") Signed-off-by: Ben Hutchings <ben.hutchings@mind.be> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-10net: dsa: microchip: Fix ksz_read64()Ben Hutchings
ksz_read64() currently does some dubious byte-swapping on the two halves of a 64-bit register, and then only returns the high bits. Replace this with a straightforward expression. Fixes: e66f840c08a2 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver") Signed-off-by: Ben Hutchings <ben.hutchings@mind.be> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-10Merge tag 'linux-can-fixes-for-5.14-20210810' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can linux-can-fixes-for-5.14-20210810 Marc Kleine-Budde says: ==================== pull-request: can 2021-08-10 this is a pull request of 2 patches for net/master. Baruch Siach's patch fixes a typo for the Microchip CAN BUS Analyzer Tool entry in the MAINTAINERS file. Hussein Alasadi fixes the setting of the M_CAN_DBTP register in the m_can driver. The regression git mainline in v5.14-rc1, so no backport to stable is needed. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-10Merge tag 'mlx5-fixes-2021-08-09' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mahameed says: ==================== mlx5 fixes 2021-08-09 This series introduces fixes to mlx5 driver. Please pull and let me know if there is any problem. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-10Merge branch '100GbE' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2021-08-09 This series contains updates to ice and iavf drivers. Ani prevents the ice driver from accidentally being probed to a virtual function and stops processing of VF messages when VFs are being torn down. Brett prevents the ice driver from deleting is own MAC address. Fahad ensures the RSS LUT and key are always set following reset for iavf. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-10can: m_can: m_can_set_bittiming(): fix setting M_CAN_DBTP registerHussein Alasadi
This patch fixes the setting of the M_CAN_DBTP register contents: - use DBTP_ (the data bitrate macros) instead of NBTP_ which area used for the nominal bitrate - do not overwrite possibly-existing DBTP_TDC flag by ORing reg_btp instead of overwriting Link: https://lore.kernel.org/r/FRYP281MB06140984ABD9994C0AAF7433D1F69@FRYP281MB0614.DEUP281.PROD.OUTLOOK.COM Fixes: 20779943a080 ("can: m_can: use bits.h macros for all regmasks") Cc: Torin Cooper-Bennun <torin@maxiluxsystems.com> Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com> Signed-off-by: Hussein Alasadi <alasadi@arecs.eu> [mkl: update patch description, update indention] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2021-08-09net/mlx5: Fix return value from tracer initializationAya Levin
Check return value of mlx5_fw_tracer_start(), set error path and fix return value of mlx5_fw_tracer_init() accordingly. Fixes: c71ad41ccb0c ("net/mlx5: FW tracer, events handling") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-08-09net/mlx5: Synchronize correct IRQ when destroying CQShay Drory
The CQ destroy is performed based on the IRQ number that is stored in cq->irqn. That number wasn't set explicitly during CQ creation and as expected some of the API users of mlx5_core_create_cq() forgot to update it. This caused to wrong synchronization call of the wrong IRQ with a number 0 instead of the real one. As a fix, set the IRQ number directly in the mlx5_core_create_cq() and update all users accordingly. Fixes: 1a86b377aa21 ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices") Fixes: ef1659ade359 ("IB/mlx5: Add DEVX support for CQ events") Signed-off-by: Shay Drory <shayd@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
generated by cgit (git 2.34.1) at 2025-04-17 17:26:00 +0000