summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2018-12-19dpaa2-eth: Add QBMAN related statsIoana Radulescu
Add statistics for pending frames in Rx/Tx conf FQs and number of buffers in pool. Available through ethtool -S. Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com> Signed-off-by: Ioana ciornei <ioana.ciornei@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-19net: phy: mscc: Fix the VSC 8531/41 Chip Init sequenceRaju Lakkaraju
- Turn on Broadcast writes - UNH 1.8.1 clear bias for UNH 1000BT distortion - UNH 1.8.7 optimize pre-emphasis for 100BasTx UNH 100W fix - Enable Token-ring during 'Coma Mode' Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-19Merge tag 'mac80211-next-for-davem-2018-12-19' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Johannes Berg says: ==================== This time we have too many changes to list, highlights: * virt_wifi - wireless control simulation on top of another network interface * hwsim configurability to test capabilities similar to real hardware * various mesh improvements * various radiotap vendor data fixes in mac80211 * finally the nl_set_extack_cookie_u64() we talked about previously, used for * peer measurement APIs, right now only with FTM (flight time measurement) for location * made nl80211 radio/interface announcements more complete * various new HE (802.11ax) things: updates, TWT support, ... ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-18net: ethernet: don't set phylib state CHANGELINK in driversHeiner Kallweit
After phy_start() phylib takes care of all needed actions, including aneg settings and checking link state. There's no need to set state PHY_CHANGELINK in drivers. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-18net: phy: remove unused code in phy_probeHeiner Kallweit
3c1bcc8614db ("net: ethernet: Convert phydev advertize and supported from u32 to link mode") left some unused code in phy_probe(), remove it. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-18Merge tag 'mlx5-uplink-rep-2018-12-15' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mahameed: ==================== mlx5-uplink-rep-2018-12-15 Or Gerlitz says: This series is essentially a cleanup to align with the rest of the NIC switchdev drivers and make us more robust and clear/n: currently the PF netdev serves as the mlx5 e-switch uplink netdev representor when going into switchdev mode and back as plain NIC netdev when going out. This causes some irregularities and misc troubles. Move to use dedicated uplink rep, as we have for the VF vports. The uplink rep netdev does has sysfs link and supports the sriov vf mac ndo, these two are in use by libvirt and other orchestrators, It also has richer ethtool support to allow controlling the port link & mtu along with supporting dcb and plugging into the mlx5 lag logic. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-18qlcnic: remove set but not used variables 'op, cmd_op'YueHaibing
Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:1070:5: warning: variable 'op' set but not used [-Wunused-but-set-variable] drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:1342:5: warning: variable 'cmd_op' set but not used [-Wunused-but-set-variable] 'op' never used since introduction in commit 7cb03b2347d5 ("qlcnic: Support VF-PF communication channel commands.") 'cmd_op' not used since commit 6226204bcf20 ("qlcnic: Fix operation type and command type.") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-18net: phy: print stack trace in phy_errorHeiner Kallweit
So far phy_error() silently stops the PHY state machine. If the network driver doesn't inform about a MDIO error then the user may wonder why his network is down. Let's print the stack trace to facilitate search for the root cause of the error. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-18net: phy: improve phy state checkingHeiner Kallweit
Add helpers phy_is_started() and __phy_is_started() to avoid open-coded checks whether PHY has been started. To make the check easier move PHY_HALTED before PHY_UP in enum phy_state. Further improvements: phy_start_aneg(): Return -EBUSY and print warning if function is called from a non-started state (DOWN, READY, HALTED). Better check because function is exported and drivers may use it incorrectly. phy_interrupt(): Return IRQ_NONE also if state is DOWN or READY. We should never receive an interrupt in one of these states, but better play safe. phy_stop(): Just return and print a warning if PHY is in a non-started state. This warning should help to identify drivers with unbalanced calls to phy_start() / phy_stop(). phy_state_machine(): Schedule state machine run only if PHY is in a started state. E.g. if state is READY we don't need the state machine, it will be started by phy_start(). v2: - don't use __func__ within phy_warn_state v3: - use WARN() instead of printing error message to facilitate debugging Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-18net: fec: remove workaround to restart phylib state machine on MDIO timeoutHeiner Kallweit
There's a workaround to restart the phylib state machine in case of a MDIO access timeout. Seems it was introduced to deal with the consequences of a too small MDIO timeout. See also commit message of c3b084c24c8a ("net: fec: Adjust ENET MDIO timeouts") which increased the timeout value later. Due to the later timeout value fix it seems to be safe to remove the workaround. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-18bonding: fix indentation issues, remove extra spacesColin Ian King
There are two statements that are indented too much by one space each, fix these. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-18net: hns3: fix a SSU buffer checking bugYunsheng Lin
When caculating the SSU buffer, it first allocate tx and rx private buffer, then the remaining buffer is for rx shared buffer. The remaining buffer size should be at least bigger than or equal to the shared_std, which is the minimum shared buffer size required by the driver, but currently if the remaining buffer size is equal to the shared_std, it returns failure, which causes SSU buffer allocation failure problem. This patch fixes this problem by rounding up shared_std before checking the the remaining buffer size bigger than or equal to the shared_std. Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-18net: hns3: aligning buffer size in SSU to 256 bytesYunsheng Lin
The hardware expects the buffer size set to SSU is aligned to 256 bytes, this patch aligns the buffer size to 256 byte using roundup or rounddown function. Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-18net: hns3: getting tx and dv buffer size through firmwareYunsheng Lin
This patch adds support of getting tx and dv buffer size through firmware, because different version of hardware requires different size of tx and dv buffer. This patch also add dv_buf_size to tc' private buffer size even if pfc is not enable for the tc. Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-18net: hns3: synchronize speed and duplex from phy when phy link upPeng Li
Driver calls phy_connect_direct and registers hclge_mac_adjust_link to synchronize mac speed and duplex from phy. It is better to synchronize mac speed and duplex from phy when phy link up. Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-18net: hns3: remove 1000M/half support of phyFuyun Liang
Our phy does not support 1000M/half, this patch removes 1000M/half from PHY_SUPPORTED_FEATURES. Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-18net: hns3: update coalesce param per secondPeng Li
coalesce param updates every 100 napi times, it may update a little late if ping test after a high rate flow, may over napi poll is called 100 times as ping test sends packets every second. This patch updates coalesce param every second, instead with every 100 napi times. It can not update the param 100% in time, but the lag time is very short. Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-18net: hns3: fix incomplete uninitialization of IRQ in the ↵Huazhong Tan
hns3_nic_uninit_vector_data() In the hns3_nic_uninit_vector_data(), the procedure of uninitializing the tqp_vector's IRQ has not set affinity_notify to NULL and changes its init flag. This patch fixes it. And for simplificaton, local variable tqp_vector is used instead of priv->tqp_vector[i]. Fixes: 424eb834a9be ("net: hns3: Unified HNS3 {VF|PF} Ethernet Driver for hip08 SoC") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-18net: hns3: remove unnecessary configuration recapture while resettingHuazhong Tan
When doing reset, it is unnecessary to get the hardware's default configuration again, otherwise, the user's configuration will be overwritten. Fixes: 4ed340ab8f49 ("net: hns3: Add reset process in hclge_main") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-18net: hns3: update some variables while hclge_reset()/hclgevf_reset() doneHuazhong Tan
When hclge_reset() completes successfully, it should update the last_reset_time, set reset_fail_cnt to 0, and set reset_type of hnae3_ae_dev to HNAE3_NONE_RESET. Also when hclgevf_reset() completes successfully, it should update the last_reset_time, and set reset_type of hnae3_ae_dev to HNAE3_NONE_RESET. Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-18net: hns3: fix napi_disable not return problemHuazhong Tan
While doing DOWN, the calling of napi_disable() may not return, since the napi_complete() in the hns3_nic_common_poll() will never be called when HNS3_NIC_STATE_DOWN is set. So we need to call napi_complete() before checking HNS3_NIC_STETE_DOWN. Fixes: ff0699e04b97 ("net: hns3: stop napi polling when HNS3_NIC_STATE_DOWN is set") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-18net: hns3: uninitialize pci in the hclgevf_uninitHuazhong Tan
In the hclgevf_pci_reset(), it only uninitialize and initialize the msi, so if the initialization fails, hclgevf_uninit_hdev() does not need to uninitialize the msi, but needs to uninitialize the pci, otherwise it will cause pci resource not free. Fixes: 862d969a3a4d ("net: hns3: do VF's pci re-initialization while PF doing FLR") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-18net: hns3: fix error handling int the hns3_get_vector_ring_chainHuazhong Tan
When hns3_get_vector_ring_chain() failed in the hns3_nic_init_vector_data(), it should do the error handling instead of return directly. Also, cur_chain should be freed instead of chain and head->next should be set to NULL in error handling of hns3_get_vector_ring_chain. This patch fixes them. Fixes: 73b907a083b8 ("net: hns3: bugfix for buffer not free problem during resetting") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-18mac80211_hwsim: fix overwriting of if_combinationJames Prestwood
Moved setting if_combination.num_different_channels/radar_detect_widths into an else after use_chanctx. In the case of use_chanctx, these two settings were getting overwritten. Signed-off-by: James Prestwood <james.prestwood@linux.intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-12-17nfp: flower: fix cb_ident duplicate in indirect block registerJohn Hurley
Previously the identifier used for indirect block callback registry and for block rule cb registry (when done via indirect blocks) was the pointer to the netdev we were interested in receiving updates on. This worked fine if a single app existed that registered one callback per netdev of interest. However, if multiple cards are in place and, in turn, multiple apps, then each app may register the same callback with the same identifier to both the netdev's indirect block cb list and to a block's cb list. This can lead to EEXIST errors and/or incorrect cb deletions. Prevent this conflict by using the app pointer as the identifier for netdev indirect block cb registry, allowing each app to register a unique callback per netdev. For block cb registry, the same app may register multiple cbs to the same block if using TC shared blocks. Instead of the app, use the pointer to the allocated cb_priv data as the identifier here. This means that there can be a unique block callback for each app/netdev combo. Fixes: 3166dd07a9cb ("nfp: flower: offload tunnel decap rules via indirect TC blocks") Reported-by: Edward Cree <ecree@solarflare.com> Signed-off-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-17mlxsw: spectrum: Update the supported firmware to version 13.1910.622Shalom Toledo
This new firmware contains: * New packet traps for discarded packets * Secure firmware flash bug fix * Fence mechanism bug fix * TCAM RMA bug fix Signed-off-by: Shalom Toledo <shalomt@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-17bnxt_en: query force speeds before disabling autoneg mode.Vasundhara Volam
With autoneg enabled, PHY loopback test fails. To disable autoneg, driver needs to send a valid forced speed to FW. FW is not sending async event for invalid speeds. To fix this, query forced speeds and send the correct speed when disabling autoneg mode. Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-17bnxt_en: Do not free port statistics buffer when device is down.Michael Chan
Port statistics which include RDMA counters are useful even when the netdevice is down. Do not free the port statistics DMA buffers when the netdevice is down. This is keep the snapshot of the port statistics and counters will just continue counting when the netdevice goes back up. Split the bnxt_free_stats() function into 2 functions. The port statistics buffers will only be freed when the netdevice is removed. Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-17bnxt_en: Save ring statistics before reset.Michael Chan
With the current driver, the statistics reported by .ndo_get_stats64() are reset when the device goes down. Store a snapshot of the rtnl_link_stats64 before shutdown. This snapshot is added to the current counters in .ndo_get_stats64() so that the counters will not get reset when the device is down. Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-17bnxt_en: Return linux standard errors in bnxt_ethtool.cVasundhara Volam
Currently firmware specific errors are returned directly in flash_device and reset ethtool hooks. Modify it to return linux standard errors to userspace when flashing operations fail. Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-17bnxt_en: Don't set ETS on unused TCs.Michael Chan
Currently, the code allows ETS bandwidth weight 0 to be set on unused TCs. We should not set any DCB parameters on unused TCs at all. Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-17bnxt_en: Add ethtool -S priority counters.Michael Chan
Display the CoS counters as additional priority counters by looking up the priority to CoS queue mapping. If the TX extended port statistics block size returned by firmware is big enough to cover the CoS counters, then we will display the new priority counters. We call firmware to get the up-to-date pri2cos mapping to convert the CoS counters to priority counters. Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-17bnxt_en: Add SR-IOV support for 57500 chips.Michael Chan
There are some minor differences when assigning VF resources on the new chips. The MSIX (NQ) resource has to be assigned and ring group is not needed on the new chips. Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-17bnxt_en: Disable MSIX before re-reserving NQs/CMPL rings.Michael Chan
When bringing up a device, the code checks to see if the number of MSIX has changed. pci_disable_msix() should be called first before changing the number of reserved NQs/CMPL rings. This ensures that the MSIX vectors associated with the NQs/CMPL rings are still properly mapped when pci_disable_msix() masks the vectors. This patch will prevent errors when RDMA support is added for the new 57500 chips. When the RDMA driver shuts down, the number of NQs is decreased and we must use the new sequence to prevent MSIX errors. Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-17bnxt_en: Reserve 1 stat_ctx for RDMA driver.Vasundhara Volam
bnxt_en requires same number of stat_ctxs as CP rings but RDMA requires only 1 stat_ctx. Also add a new parameter resv_stat_ctxs to better keep track of stat_ctxs reserved including resources used by RDMA. Add a stat_ctxs parameter to all the relevant resource reservation functions so we can reserve the correct number of stat_ctxs. Prior to this patch, we were not reserving the extra stat_ctx for RDMA and RDMA would not work on the new 57500 chips. Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-17bnxt_en: Do not modify max_stat_ctxs after RDMA driver requests/frees stat_ctxsVasundhara Volam
Calling bnxt_set_max_func_stat_ctxs() to modify max stat_ctxs requested or freed by the RDMA driver is wrong. After introducing reservation of resources recently, the driver has to keep track of all stat_ctxs including the ones used by the RDMA driver. This will provide a better foundation for accurate accounting of the stat_ctxs. Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-17bnxt_en: get rid of num_stat_ctxs variableVasundhara Volam
For bnxt_en driver, stat_ctxs created will always be same as cp_nr_rings. Remove extra variable that duplicates the value. Also introduce bnxt_get_avail_stat_ctxs_for_en() helper to get available stat_ctxs and bnxt_get_ulp_stat_ctxs() helper to return number of stat_ctxs used by RDMA. Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-17bnxt_en: Add bnxt_get_avail_cp_rings_for_en() helper function.Michael Chan
The available CP rings are calculated differently on the new 57500 chips, so add this helper to do this calculation correctly. The VFs will be assigned these available CP rings. Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-17bnxt_en: Store the maximum NQs available on the PF.Michael Chan
The PF has a pool of NQs and MSIX vectors assigned to it based on NVRAM configurations. The number of usable MSIX vectors on the PF is the minimum of the NQs and MSIX vectors. Any excess NQs without associated MSIX may be used for the VFs, so we need to store this max_nqs value. max_nqs minus the NQs used by the PF will be the available NQs for the VFs. Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-17ucc_geth: Add change_carrier() for Fixed PHYsJoakim Tjernlund
This allows to control carrier from /sys/class/net/ethX/carrier for Fixed PHYs. Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-17gianfar: Add change_carrier() for Fixed PHYsJoakim Tjernlund
This allows to control carrier from /sys/class/net/ethX/carrier for Fixed PHYs. Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-17dpaa_eth: Add change_carrier() for Fixed PHYsJoakim Tjernlund
This allows to control carrier from /sys/class/net/ethX/carrier for Fixed PHYs. Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-17Fixed PHY: Add fixed_phy_change_carrier()Joakim Tjernlund
Drivers can use this as .ndo_change_carrier() to change carrier via /sys/class/net/ethX/carrier. Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-17net/mlx4_en: remove fallback after kzalloc_node()Eric Dumazet
kzalloc_node(..., GFP_KERNEL, node) will attempt to allocate memory as close as possible to the node. There is no need to fallback to kzalloc() if this has failed. Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-17net/mlx5e: Add some ethtool port control entries to the uplink rep netdevOr Gerlitz
Some of the ethtool entries to control the port should be supported by the uplink rep netdev in switchdev mode, add them. While here, add also the get/set coalesce entries for all reps. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-17net/mlx5e: Expose ethtool pause and link functions to mlx5e callersOr Gerlitz
Towards supporting set/get of global pause for the port and get of the port link ksetting from the uplink representor, expose the relevant entries to other mlx5 callers. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-17net/mlx5e: Add sriov and udp tunnel ndo support for the uplink repOr Gerlitz
Some of the sriov ndo calls are needed also on the switchdev mode - e.g setup VF mac and reading vport stats. Add them to the uplink rep netdev ops. Same for the UDP tunnel ones, need them there to identify offloaded udp tunnel ports. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-17net/mlx5e: Handle port mtu/link, dcb and lag for uplink repsOr Gerlitz
Take care of setup/teardown for the port link, dcb, lag as well as dealing with port mtu and carrier for e-switch uplink representors. This is achieved by adding a dedicated profile instance for uplink representors which includes the enable/disable and more profile routines which are invoked by the general mlx5e code for netdev attach/detach. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-17net/mlx5e: Uninstantiate esw manager vport netdev on switchdev modeOr Gerlitz
Now, when we have a dedicated uplink representor, the netdev instance set over the esw manager vport (PF) is of no-use. As such, remove it once we're on switchdev mode and get it back to life when off switchdev. This is done by reloading the Ethernet interface as well (we already do that for the IB interface) from the eswitch code while going in/out of switchdev mode. The Eth add/remove entries are modified to act differently when called in switchdev mode. In this case we only deal with registration of the eth vport representors. The rep netdevices are created from the eswitch call to load the registered eth representors. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-17net/mlx5e: Remove leftover code from the PF netdev being uplink repOr Gerlitz
Remove some last leftovers from using the PF netdev as the e-switch uplink representor. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
generated by cgit (git 2.34.1) at 2025-05-12 15:46:20 +0000