summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2015-06-10cxgb4: Add a debugfs entry to dump CIM MA logic analyzer logsHariprasad Shenai
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-10bna: remove obsolete use of EXTRA_CFLAGSJiri Slaby
EXTRA_CFLAGS should be used on the command line only. Since EXTRA_CFLAGS here add only a non-existant path to compiler include paths (by -I), remove EXTRA_CFLAGS completely. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-09can: mcp251x: use correct register address for acceptance filtersTomas Krcka
This patch corrects addresses of acceptance filters. These registers are not in use, but values should be correct. Tested with MCP2515 and am3352 and also checked datasheets for MCP2515 and MCP2510. Signed-off-by: Tomas Krcka <tomas.krcka@nkgroup.cz> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2015-06-08Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
2015-06-08net: phy: dp83867: Fix device tree entriesDan Murphy
Fix the device tree entries to modify the '_' to '-'. Also changes the names of the internal delay properties from -int- to -internal- as the -int- appeared as a keyword. Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-08net: phy: bcm7xxx: update workaround to fix 100BaseT corner casesFlorian Fainelli
Update the AFE_TX_CONFIG value to solve marginal rise/fall issues observed when the link is operating in 100BaseT. This workaround applies to GPHY revisions D0, E0 and newer. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-08net: bcmgenet: power on MII block for all MII modesFlorian Fainelli
The RGMII block is currently only powered on when using RGMII or RGMII_NO_ID, which is not correct when using the GENET interface in MII or Reverse MII modes. We always need to power on the RGMII interface for this block to properly work, regardless of the MII mode in which we operate. Fixes: aa09677cba423 ("net: bcmgenet: add MDIO routines") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-08net/phy: micrel: Center FLP timing at 16msJaeden Amero
Link failures have been observed when using the KSZ9031 with HP 1810-8G and HP 1910-8G network switches. Center the FLP timing at 16ms to help avoid intermittent link failures. >From the KSZ9031RNX and KSZ9031MNX data sheets revision 2.2, section "Auto-Negotiation Timing": The KSZ9031[RNX or MNX] Fast Link Pulse (FLP) burst-to-burst transmit timing for Auto-Negotiation defaults to 8ms. IEEE 802.3 Standard specifies this timing to be 16ms +/-8ms. Some PHY link partners need to receive the FLP with 16ms centered timing; otherwise, there can be intermittent link failures and long link-up times. The PHY data sheet recommends configuring the FLP burst registers after power-up/reset and immediately thereafter restarting auto-negotiation, so we center the FLP timing at 16ms and then restart auto-negotiation in the config_init for KSZ9031. Signed-off-by: Jaeden Amero <jaeden.amero@ni.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-08net/phy: micrel: Comment MMD address of extended registersJaeden Amero
There are some defines for a few pad skew related extended registers. Specify for which MMD Address (dev_addr) they are for. Signed-off-by: Jaeden Amero <jaeden.amero@ni.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-08net/phy: micrel: Be more const correctJaeden Amero
In a few places in this driver, we weren't using const where we could have. Use const more. In addition, change the arrays of strings in ksz9031_config_init() to be not only const, but also static. Signed-off-by: Jaeden Amero <jaeden.amero@ni.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-07wan: dscc4: use msecs_to_jiffies for conversionsNicholas Mc Guire
API compliance scanning with coccinelle flagged: ./drivers/net/wan/dscc4.c:1036:1-33: WARNING: timeout (10) seems HZ dependent ./drivers/net/wan/dscc4.c:554:2-34: WARNING: timeout (10) seems HZ dependent ./drivers/net/wan/dscc4.c:599:2-34: WARNING: timeout (10) seems HZ dependent Numeric constants passed to schedule_timeout_*() make the effective timeout HZ dependent which does not seem to be the intent here. Fixed up by converting the constant to jiffies with msecs_to_jiffies(), passing 100ms (assuming HZ==100 in the original code). Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-07cosa: use msecs_to_jiffies for conversionsNicholas Mc Guire
API compliance scanning with coccinelle flagged: ./drivers/net/wan/cosa.c:520:2-18: WARNING: timeout (30) seems HZ dependent Numeric constants passed to schedule_timeout() make the effective timeout HZ dependent which makes little sense in a device probe. Fixed up by converting the constant to jiffies with msecs_to_jiffies() Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-07net/mlx5_core: Fix static checker warnings around system guid query flowMajd Dibbiny
Fix static checker warnings in the flow of system guid query. Fixes: 707c4602cda6 ('net/mlx5_core: Add new query HCA vport commands') Signed-off-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-07b44: call netif_napi_del()Hauke Mehrtens
When the driver gets unregistered a call to netif_napi_del() was missing, this all was also missing in the error paths of b44_init_one(). Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-07ethernet: micrel: use time_is_before_eq_jiffiesAntonio Murdaca
use time_is_before_eq_jiffies macro for time comparison Signed-off-by: Antonio Murdaca <antonio.murdaca@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-07be2net: Replace dma/pci_alloc_coherent() calls with dma_zalloc_coherent()Sriharsha Basavapatna
There are several places in the driver (all in control paths) where coherent dma memory is being allocated using either dma_alloc_coherent() or the deprecated pci_alloc_consistent(). All these calls should be changed to use dma_zalloc_coherent() to avoid uninitialized fields in data structures backed by this memory. Reported-by: Joerg Roedel <jroedel@suse.de> Tested-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@avagotech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-07net: fec: ptp: correct the ENET_ATCOR valueFugang Duan
The current driver adjust freq formula is: fe * diff = ppb * pc Note: fe: ENET ref clock frequency in Hz diff = inc_corr - inc: difference between default increment and correction increment ppb: parts per billion adjustment from base pc: correction period (in number of fe clock cycles) The correction increment will be used after N cycles of regular increments, not every N cycles (with N being the correction period). For example, set ENET_ATCOR=4, INC=8, INC_CORR=9, there will be 4 increments of 8 (ENET_ATINC[INC]) , followed by 1 increment of 9 (ENET_ATINC[INC_CORR]). So, the correct formula is: fe * diff = ppb * (pc + 1) For ENET_ATCOR, a value 0 disables the correction counter and no corrections occur. So base on the origin formula, set pc = pc > 1 ? pc - 1 : pc. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-07net: ll_temac: Remove sparse warningsMichal Simek
Remove sparse warnings: drivers/net/ethernet/xilinx/ll_temac_main.c:65:16: warning: cast removes address space of expression drivers/net/ethernet/xilinx/ll_temac_main.c:70:9: warning: cast removes address space of expression drivers/net/ethernet/xilinx/ll_temac_main.c:127:16: warning: cast removes address space of expression drivers/net/ethernet/xilinx/ll_temac_main.c:137:9: warning: cast removes address space of expression drivers/net/ethernet/xilinx/ll_temac_main.c:409:3: warning: symbol 'temac_options' was not declared. Should it be static? drivers/net/ethernet/xilinx/ll_temac_main.c:590:6: warning: symbol 'temac_adjust_link' was not declared. Should it be static? Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-07net: bcmgenet: improve TX timeoutFlorian Fainelli
Dump useful ring statistics along with interrupt status, software maintained pointers and hardware registers to help troubleshoot TX queue stalls. When a timeout occurs, disable TX NAPI for the rings, dump their states while interrupts are disabled, re-enable interrupts, NAPI and queue flow control to help with the recovery. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-07net: dsa: mv88e6xxx: Fix deadlock by double lockAndrew Lunn
ethtool -S on a DSA interface can deadlock for some switches because the same lock is taken twice. Use the register read function which expects the lock to be already held. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Fixes: 31888234b736 ("net: dsa: mv88e6xxx: Replace stats mutex with SMI mutex") Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-07fddi: print an address with %p format specifier rather than %xColin Ian King
The debug is printing the struct smt_header * address using the %x format specifier. Fix it to use %p instead. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-07amd-xgbe: Use disable_irq_nosync from within timer functionLendacky, Thomas
Since the Tx timer function runs in softirq context the driver needs to call disable_irq_nosync instead of a disable_irq. Reported-by: Josh Stone <jistone@redhat.com> Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-07wan: dscc4: fix build warning Wunused-but-set-variableNicholas Mc Guire
Fix: drivers/net/wan/dscc4.c: In function 'dscc4_open': drivers/net/wan/dscc4.c:1049:25: warning: variable 'ppriv' set but not used [-Wunused-but-set-variable] This has been in there unused since 1da177e4c3f (Linux-2.6.12-rc2) simply remove it. Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-05cxgb4: Fix static checker warningHariprasad Shenai
The patch e85c9a7abfa4: ("cxgb4/cxgb4vf: Add code to calculate T5 BAR2 Offsets for SGE Queue Registers") from Dec 3, 2014, leads to the following static checker warning: drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:5358 t4_bar2_sge_qregs() warn: should '(qid >> qpp_shift) << page_shift' be a 64 bit type? This patch fixes it Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-05cxgb4: Use FW LDST cmd to access TP_PIO_{ADDR, DATA} register firstHariprasad Shenai
The TP_PIO_{ADDR,DATA} registers are are in conflict with the firmware's use of these registers. Added a routine to access it through FW LDST cmd. Access all TP_PIO_{ADDR,DATA} register access through new routine if FW is alive. If firmware is dead, than fall back to indirect access. Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-05cxgb4: program pci completion timeoutHariprasad Shenai
Set pci completion timeout to 0xd. Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-05cxgb4: Set mac addr from vpd, when we can't contact firmwareHariprasad Shenai
Grab the Adapter MAC Address out of the VPD and use it for the "debug" network interface when either we can't contact the firmware Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-05cxgb4: Rename t4_link_start() to t4_link_l1cfgHariprasad Shenai
t4_link_start() was completely misnamed. It does _not_ start up the link. It merely does the L1 Configuration for the link. The Link Up process is started automatically by the firmware when the number of enabled Virtual Interfaces on a port goes from 0 to 1. So renaming this routine to t4_link_l1cfg() for better documentation. Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-05cxgb4: Add sge ec context flush serviceHariprasad Shenai
Add function to flush the sge ec context cache, and utilize this new function in the driver Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-05cxgb4: Free Virtual Interfaces in remove routineHariprasad Shenai
Free VI interfaces in remove routine. If we don't do this then the firmware will never drop the physical link to the peer. Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-04i40e: Make sure to be in VEB mode if SRIOV is enabled at probeAnjali Singhai Jain
If SRIOV is enabled we need to be in VEB mode not VEPA mode at probe. This fixes an NPAR bug when SRIOV is enabled in the BIOS. Change-ID: Ibf006abafd9a0ca3698ec24848cd771cf345cbbc Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-06-04i40e: start up in VEPA mode by defaultAnjali Singhai Jain
The patch fixes a bug in the default configuration which prevented a software bridge loaded on the PF interface from working correctly because broadcast packets are incorrectly looped back. Fix the general case, by loading the driver in VEPA mode Until a VF or VMDq VSI is added. This way loopback on the Main VSI is turned off until needed and can resolve the issue of unnecessary reflection for users that do not have VF or VMDq VSIs setup. The driver must now coordinate the loopback setting for the Flow Director (FDIR) VSI to make sure it is in sync with the current VEB or VEPA mode setting. The user can still switch bridge modes from the bridge commands and choose to be in VEPA mode with VF VSIs. Because of hardware requirements, the call to switch to VEB mode when no VF/VMDqs are present will be rejected. NOTE: This patch uses BIT_ULL as that is preferred going forward, a followup patch in the lower priority queue to net-next will fix up the remaining 1 << usages. Change-ID: Ib121ddb18fe4b3c4f52e9deda6fcbeb9105683d1 Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-06-04i40e/i40evf: Fix mixed size frags and linearizationAnjali Singhai Jain
This patch fixes a bug where the i40e Tx queue will hang if this skb is passed to the driver. With mixed size fragments while using TSO there was a corner case where we needed to linearize but we were not. This was seen with iSCSI traffic and could be reproduced with a frag list that looks like this: num_frags = 17, gso_segs = 17, hdr_len = 66, skb_shinfo(skb)->gso_size = 1448 size = 3002, j = 1, frag_size = 2936, num_frags = 17 size = 4268, j = 1, frag_size = 4096, num_frags = 16 size = 5534, j = 1, frag_size = 4096, num_frags = 15 size = 5352, j = 1, frag_size = 4096, num_frags = 14 size = 5170, j = 1, frag_size = 4096, num_frags = 13 size = 3468, j = 1, frag_size = 2576, num_frags = 12 size = 750, j = 1, frag_size = 112, num_frags = 11 size = 862, j = 2, frag_size = 112, num_frags = 10 size = 974, j = 3, frag_size = 112, num_frags = 9 size = 1126, j = 4, frag_size = 152, num_frags = 8 size = 1330, j = 5, frag_size = 204, num_frags = 7 size = 1534, j = 6, frag_size = 204, num_frags = 6 size = 356, j = 1, frag_size = 204, num_frags = 5 size = 560, j = 2, frag_size = 204, num_frags = 4 size = 764, j = 3, frag_size = 204, num_frags = 3 size = 968, j = 4, frag_size = 204, num_frags = 2 size = 1140, j = 5, frag_size = 172, num_frags = 1 result: linearize = 0, j = 6 Change-ID: I79bb1aeab0af255fe2ce28e93672a85d85bf47e8 Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-06-04mlx5: Enable mutual support for IB and EthernetHaggai Abramonvsky
Ethernet functionality is only available when working in ISSI > 0 mode. Previously, the IB driver wasn't ready to work on that mode, and hence building both the IB driver and the Ethernet functionality in the core driver were disallowed by Kconfigs. Now, once we have all the pre-steps in place, we can remove this limitation. The last steps in the IB driver for getting that setup to work are: create dummy SRQ for the driver's use (until now we could use XRC_SRQ as SRQ and XRC_SRQ, after moving to ISSI > 0, we separate XRC SRQs from basic SRQs) and adapt the create QP function to be compatible with ISSI > 0. Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-04net/mlx5_core: Add more query port helpersMajd Dibbiny
Add the following helpers: 1. mlx5_query_port_proto_oper -- queries the port speed port mask 2. mlx5_query_port_link_width_oper - queries the port link with bitmask 3. mlx5_query_port_vl_hw_cap - queries the Virtual Lanes supported on this port These helpers will be used from the IB driver when working in ISSI > 0 mode. Signed-off-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-04net/mlx5_core: Use port number when querying port ptysMajd Dibbiny
Until now, mlx5_query_port_ptys always queried port number one. Added new argument in the function's prototype so we can also query the second port. This will be needed when thr helper will be invoked from the IB driver on non FPP (Function-Per-Port) devices. Signed-off-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-04net/mlx5_core: Use port number in the query port mtu helpersMajd Dibbiny
Extend the function prototypes for max and operational mtu to take the local port number. In the Ethernet driver is this hard coded to one, since ConnectX4 Ethernet devices are always function-per-port. The IB driver also serves older devices (ConnectIB) which isn't such, and hence the part can vary. Signed-off-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-04net/mlx5_core: Get vendor-id using the query adapter commandMajd Dibbiny
Add two wrapper functions to the query adapter command: 1. mlx5_query_board_id -- replaces the old mlx5_cmd_query_adapter. 2. mlx5_core_query_vendor_id -- retrieves the vendor_id from the query_adapter command. Signed-off-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-04net/mlx5_core: Add new query HCA vport commandsMajd Dibbiny
Added the implementation for the following commands: 1. QUERY_HCA_VPORT_GID 2. QUERY_HCA_VPORT_PKEY 3. QUERY_HCA_VPORT_CONTEXT They will be needed when we move to work with ISSI > 0 in the IB driver too. Signed-off-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-04net/mlx5_core: Make the vport helpers available for the IB driver tooMajd Dibbiny
Move the vport header file to be under include/linux/mlx5, such that the mlx5 IB can use it as well. Also add nic_ prefix to the vport NIC commands to differeniate between HCA vport commands and NIC vport commands. Signed-off-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-04net/mlx5_core: Check the return bitmask when querying ISSIHaggai Abramonvsky
The determination of the supported ISSI versions should be conditioned on the returned mask, and not only on the return status of the query ISSI command, fix that. Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com> Signed-off-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-04net/mlx5_core: Enable XRCs and SRQs when using ISSI > 0Haggai Abramonvsky
When working in ISSI > 0 mode, the model exposed by the device for XRCs and SRQs is different. XRCs use XRC SRQs and plain SRQs are based on RPM (Receive Memory Pool). Add helper functions to create, modify, query, and arm XRC SRQs and RMPs. Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-04net/mlx5_core: Apply proper name convention to helpersHaggai Abramonvsky
Some core helper functions were named with mlx5_ only prefix, fix that to mlx5_core_ so we're aligned with the overall scheme used for core services. Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-04net/mlx5_en: Add missing check for memory allocation failureAmir Vadai
The patch afb736e9330a: "net/mlx5: Ethernet resource handling files" from May 28, 2015, leads to the following static checker warning: drivers/net/ethernet/mellanox/mlx5/core/en_flow_table.c:726 mlx5e_create_main_flow_table() error: potential null dereference 'g'. (kcalloc returns null) Fixes: afb736e9330a ("net/mlx5: Ethernet resource handling files") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-04net: Add full IPv6 addresses to flow_keysTom Herbert
This patch adds full IPv6 addresses into flow_keys and uses them as input to the flow hash function. The implementation supports either IPv4 or IPv6 addresses in a union, and selector is used to determine how may words to input to jhash2. We also add flow_get_u32_dst and flow_get_u32_src functions which are used to get a u32 representation of the source and destination addresses. For IPv6, ipv6_addr_hash is called. These functions retain getting the legacy values of src and dst in flow_keys. With this patch, Ethertype and IP protocol are now included in the flow hash input. Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-03Merge tag 'wireless-drivers-next-for-davem-2015-06-03' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== new driver mt7601u for MediaTek Wi-Fi devices MT7601U ath10k: * qca6174 power consumption improvements, enable ASPM etc (Michal) wil6210: * support Wi-Fi Simple Configuration in STA mode iwlwifi: * a few fixes (re-enablement of interrupts for certain new platforms that have special power states) * Rework completely the RBD allocation model towards new multi RX hardware. * cleanups * scan reworks continuation (Luca) mwifiex: * improve firmware debug functionality rtlwifi: * update regulatory database brcmfmac: * cleanup and new feature support in PCIe code * alternative nvram loading for router support ==================== Conflicts: drivers/net/wireless/iwlwifi/Kconfig Trivial conflict in iwlwifi Kconfig, two commits adding the same two chip numbers to the help text, but order transposed. Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-03cxgb4: Remove WOL get/set ethtool supportHariprasad Shenai
Remove ethtool get/set support for wake on lan, adapter doesn't support it. Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-03cxgb4: Add support to dump loopback port statsHariprasad Shenai
Add support in ethtool to dump loopback port statistics Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-03cxgb4: Add support in ethtool to dump channel statsHariprasad Shenai
Add support in ethtool to dump adapter channel stats Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-03cxgb4: Add ethtool support to get adapter statsHariprasad Shenai
Add ethtool support to get adapter specific hardware statistics Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit (git 2.34.1) at 2025-06-05 07:34:10 +0000