| Age | Commit message (Collapse) | Author |
|---|
|
In the cited commit, if the routing device is ovs internal port, the
out device is set to uplink, and packets go out after encapsulation.
If filter device is uplink, it can trigger the following syndrome:
mlx5_core 0000:08:00.0: mlx5_cmd_out_err:803:(pid 3966): SET_FLOW_TABLE_ENTRY(0x936) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0xcdb051), err(-22)
Fix this issue by not offloading internal port if filter device is out
device. In this case, packets are not forwarded to the root table to
be processed, the termination table is used instead to forward them
from uplink to uplink.
Fixes: 100ad4e2d758 ("net/mlx5e: Offload internal port as encap route device")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Hold RTNL lock when calling xdp_set_features() with a registered netdev,
as the call triggers the netdev notifiers. This could happen when
switching from nic profile to uplink representor for example.
Similar logic which fixed a similar scenario was previously introduced in
the following commit:
commit 72cc65497065 net/mlx5e: Take RTNL lock when needed before calling
xdp_set_features().
This fixes the following assertion and warning call trace:
RTNL: assertion failed at net/core/dev.c (1961)
WARNING: CPU: 13 PID: 2529 at net/core/dev.c:1961
call_netdevice_notifiers_info+0x7c/0x80
Modules linked in: rpcrdma rdma_ucm ib_iser libiscsi
scsi_transport_iscsi ib_umad rdma_cm ib_ipoib iw_cm ib_cm mlx5_ib
ib_uverbs ib_core xt_conntrack xt_MASQUERADE nf_conntrack_netlink
nfnetlink xt_addrtype iptable_nat nf_nat br_netfilter rpcsec_gss_krb5
auth_rpcgss oid_registry overlay mlx5_core zram zsmalloc fuse
CPU: 13 PID: 2529 Comm: devlink Not tainted
6.5.0_for_upstream_min_debug_2023_09_07_20_04 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS
rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
RIP: 0010:call_netdevice_notifiers_info+0x7c/0x80
Code: 8f ff 80 3d 77 0d 16 01 00 75 c5 ba a9 07 00 00 48
c7 c6 c4 bb 0d 82 48 c7 c7 18 c8 06 82 c6 05 5b 0d 16 01 01 e8 44 f6 8c
ff <0f> 0b eb a2 0f 1f 44 00 00 55 48 89 e5 41 54 48 83 e4 f0 48 83 ec
RSP: 0018:ffff88819930f7f0 EFLAGS: 00010282
RAX: 0000000000000000 RBX: ffffffff8309f740 RCX: 0000000000000027
RDX: ffff88885fb5b5c8 RSI: 0000000000000001 RDI: ffff88885fb5b5c0
RBP: 0000000000000028 R08: ffff88887ffabaa8 R09: 0000000000000003
R10: ffff88887fecbac0 R11: ffff88887ff7bac0 R12: ffff88819930f810
R13: ffff88810b7fea40 R14: ffff8881154e8fd8 R15: ffff888107e881a0
FS: 00007f3ad248f800(0000) GS:ffff88885fb40000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000563b85f164e0 CR3: 0000000113b5c006 CR4: 0000000000370ea0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
? __warn+0x79/0x120
? call_netdevice_notifiers_info+0x7c/0x80
? report_bug+0x17c/0x190
? handle_bug+0x3c/0x60
? exc_invalid_op+0x14/0x70
? asm_exc_invalid_op+0x16/0x20
? call_netdevice_notifiers_info+0x7c/0x80
call_netdevice_notifiers+0x2e/0x50
mlx5e_set_xdp_feature+0x21/0x50 [mlx5_core]
mlx5e_build_rep_params+0x97/0x130 [mlx5_core]
mlx5e_init_ul_rep+0x9f/0x100 [mlx5_core]
mlx5e_netdev_init_profile+0x76/0x110 [mlx5_core]
mlx5e_netdev_attach_profile+0x1f/0x90 [mlx5_core]
mlx5e_netdev_change_profile+0x92/0x160 [mlx5_core]
mlx5e_vport_rep_load+0x329/0x4a0 [mlx5_core]
mlx5_esw_offloads_rep_load+0x9e/0xf0 [mlx5_core]
esw_offloads_enable+0x4bc/0xe90 [mlx5_core]
mlx5_eswitch_enable_locked+0x3c8/0x570 [mlx5_core]
? kmalloc_trace+0x25/0x80
mlx5_devlink_eswitch_mode_set+0x224/0x680 [mlx5_core]
? devlink_get_from_attrs_lock+0x9e/0x110
devlink_nl_cmd_eswitch_set_doit+0x60/0xe0
genl_family_rcv_msg_doit+0xd0/0x120
genl_rcv_msg+0x180/0x2b0
? devlink_get_from_attrs_lock+0x110/0x110
? devlink_nl_cmd_eswitch_get_doit+0x290/0x290
? devlink_pernet_pre_exit+0xf0/0xf0
? genl_family_rcv_msg_dumpit+0xf0/0xf0
netlink_rcv_skb+0x54/0x100
genl_rcv+0x24/0x40
netlink_unicast+0x1fc/0x2c0
netlink_sendmsg+0x232/0x4a0
sock_sendmsg+0x38/0x60
? _copy_from_user+0x2a/0x60
__sys_sendto+0x110/0x160
? handle_mm_fault+0x161/0x260
? do_user_addr_fault+0x276/0x620
__x64_sys_sendto+0x20/0x30
do_syscall_64+0x3d/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
RIP: 0033:0x7f3ad231340a
Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3
0f 1e fa 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f
05 <48> 3d 00 f0 ff ff 77 7e c3 0f 1f 44 00 00 41 54 48 83 ec 30 44 89
RSP: 002b:00007ffd70aad4b8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 0000000000c36b00 RCX:00007f3ad231340a
RDX: 0000000000000038 RSI: 0000000000c36b00 RDI: 0000000000000003
RBP: 0000000000c36910 R08: 00007f3ad2625200 R09: 000000000000000c
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000001
</TASK>
---[ end trace 0000000000000000 ]---
------------[ cut here ]------------
Fixes: 4d5ab0ad964d ("net/mlx5e: take into account device reconfiguration for xdp_features flag")
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When mlx5e_xdp_xmit is called without the XDP_XMIT_FLUSH set it is
possible that it leaves a mpwqe session open. That is ok during runtime:
the session will be closed on the next call to mlx5e_xdp_xmit. But
having a mpwqe session still open at XDP sq close time is problematic:
the pc counter is not updated before flushing the contents of the
xdpi_fifo. This results in leaking page fragments.
The fix is to always close the mpwqe session at the end of
mlx5e_xdp_xmit, regardless of the XDP_XMIT_FLUSH flag being set or not.
Fixes: 5e0d2eef771e ("net/mlx5e: XDP, Support Enhanced Multi-Packet TX WQE")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When a page allocation fails during refill in mlx5e_refill_rx_wqes, the
page will be released again on the next refill call. This triggers the
page_pool negative page fragment count warning below:
[ 338.326070] WARNING: CPU: 4 PID: 0 at include/net/page_pool/helpers.h:130 mlx5e_page_release_fragmented.isra.0+0x42/0x50 [mlx5_core]
...
[ 338.328993] RIP: 0010:mlx5e_page_release_fragmented.isra.0+0x42/0x50 [mlx5_core]
[ 338.329094] Call Trace:
[ 338.329097] <IRQ>
[ 338.329100] ? __warn+0x7d/0x120
[ 338.329105] ? mlx5e_page_release_fragmented.isra.0+0x42/0x50 [mlx5_core]
[ 338.329173] ? report_bug+0x155/0x180
[ 338.329179] ? handle_bug+0x3c/0x60
[ 338.329183] ? exc_invalid_op+0x13/0x60
[ 338.329187] ? asm_exc_invalid_op+0x16/0x20
[ 338.329192] ? mlx5e_page_release_fragmented.isra.0+0x42/0x50 [mlx5_core]
[ 338.329259] mlx5e_post_rx_wqes+0x210/0x5a0 [mlx5_core]
[ 338.329327] ? mlx5e_poll_rx_cq+0x88/0x6f0 [mlx5_core]
[ 338.329394] mlx5e_napi_poll+0x127/0x6b0 [mlx5_core]
[ 338.329461] __napi_poll+0x25/0x1a0
[ 338.329465] net_rx_action+0x28a/0x300
[ 338.329468] __do_softirq+0xcd/0x279
[ 338.329473] irq_exit_rcu+0x6a/0x90
[ 338.329477] common_interrupt+0x82/0xa0
[ 338.329482] </IRQ>
This patch fixes the legacy rq case by releasing all allocated fragments
and then setting the skip flag on all released fragments. It is
important to note that the number of released fragments will be higher
than the number of allocated fragments when an allocation error occurs.
Fixes: 3f93f82988bc ("net/mlx5e: RX, Defer page release in legacy rq for better recycling")
Tested-by: Chris Mason <clm@fb.com>
Reported-by: Chris Mason <clm@fb.com>
Closes: https://lore.kernel.org/netdev/117FF31A-7BE0-4050-B2BB-E41F224FF72F@meta.com
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When a page allocation fails during refill in mlx5e_post_rx_mpwqes, the
page will be released again on the next refill call. This triggers the
page_pool negative page fragment count warning below:
[ 2436.447717] WARNING: CPU: 1 PID: 2419 at include/net/page_pool/helpers.h:130 mlx5e_page_release_fragmented.isra.0+0x42/0x50 [mlx5_core]
...
[ 2436.447895] RIP: 0010:mlx5e_page_release_fragmented.isra.0+0x42/0x50 [mlx5_core]
[ 2436.447991] Call Trace:
[ 2436.447975] mlx5e_post_rx_mpwqes+0x1d5/0xcf0 [mlx5_core]
[ 2436.447994] <IRQ>
[ 2436.447996] ? __warn+0x7d/0x120
[ 2436.448009] ? mlx5e_handle_rx_cqe_mpwrq+0x109/0x1d0 [mlx5_core]
[ 2436.448002] ? mlx5e_page_release_fragmented.isra.0+0x42/0x50 [mlx5_core]
[ 2436.448044] ? mlx5e_poll_rx_cq+0x87/0x6e0 [mlx5_core]
[ 2436.448061] ? report_bug+0x155/0x180
[ 2436.448065] ? handle_bug+0x36/0x70
[ 2436.448067] ? exc_invalid_op+0x13/0x60
[ 2436.448070] ? asm_exc_invalid_op+0x16/0x20
[ 2436.448079] mlx5e_napi_poll+0x122/0x6b0 [mlx5_core]
[ 2436.448077] ? mlx5e_page_release_fragmented.isra.0+0x42/0x50 [mlx5_core]
[ 2436.448113] ? generic_exec_single+0x35/0x100
[ 2436.448117] __napi_poll+0x25/0x1a0
[ 2436.448120] net_rx_action+0x28a/0x300
[ 2436.448122] __do_softirq+0xcd/0x279
[ 2436.448126] irq_exit_rcu+0x6a/0x90
[ 2436.448128] sysvec_apic_timer_interrupt+0x6e/0x90
[ 2436.448130] </IRQ>
This patch fixes the striding rq case by setting the skip flag on all
the wqe pages that were expected to have new pages allocated.
Fixes: 4c2a13236807 ("net/mlx5e: RX, Defer page release in striding rq for better recycling")
Tested-by: Chris Mason <clm@fb.com>
Reported-by: Chris Mason <clm@fb.com>
Closes: https://lore.kernel.org/netdev/117FF31A-7BE0-4050-B2BB-E41F224FF72F@meta.com
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently, whenever fw issues a change ownership event, the PF that owns
the fw tracer drops its ownership directly and the other PFs try to pick
up the ownership via what MTRC register suggests.
In some cases, driver releases the ownership of the tracer and reacquires
it later on. Whenever the driver releases ownership of the tracer, fw
issues a change ownership event. This event can be delayed and come after
driver has reacquired ownership of the tracer. Thus the late event will
trigger the tracer owner PF to release the ownership again and lead to a
scenario where no PF is owning the tracer.
To prevent the scenario described above, when handling a change
ownership event, do not drop ownership of the tracer directly, instead
read the fw MTRC register to retrieve the up-to-date owner of the tracer
and set it accordingly in driver level.
Fixes: f53aaa31cce7 ("net/mlx5: FW tracer, implement tracer logic")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
With current implementation in single FDB LAG mode all packets are
processed by eswitch 0 rules. As such, 'peer' FDB entries receive the
packets for rules of other eswitches and are responsible for updating the
main entry by sending SWITCHDEV_FDB_ADD_TO_BRIDGE notification from their
background update wq task. However, this introduces a race condition when
non-zero eswitch instance decides to delete a FDB entry, sends
SWITCHDEV_FDB_DEL_TO_BRIDGE notification, but another eswitch's update task
refreshes the same entry concurrently while its async delete work is still
pending on the workque. In such case another SWITCHDEV_FDB_ADD_TO_BRIDGE
event may be generated and entry will remain stuck in FDB marked as
'offloaded' since no more SWITCHDEV_FDB_DEL_TO_BRIDGE notifications are
sent for deleting the peer entries.
Fix the issue by synchronously marking deleted entries with
MLX5_ESW_BRIDGE_FLAG_DELETED flag and skipping them in background update
job.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently, mlx5 is registering event handler for vport context change
event some time after arming the event. this can lead to missing an
event, which will result in wrong rules in the FDB.
Hence, register the event handler before arming the event.
This solution is valid since FW is sending vport context change event
only on vports which SW armed, and SW arming the vport when enabling
it, which is done after the FDB has been created.
Fixes: 6933a9379559 ("net/mlx5: E-Switch, Use async events chain")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The cited patch change mlx5 driver so that during probe DMA
operations were performed before pci_enable_device(), and during
teardown DMA operations were performed after pci_disable_device().
DMA operations require PCI to be enabled. Hence, The above leads to
the following oops in PPC systems[1].
On s390x systems, as reported by Niklas Schnelle, this is a problem
because mlx5_pci_init() is where the DMA and coherent mask is set but
mlx5_cmd_init() already does a dma_alloc_coherent(). Thus a DMA
allocation is done during probe before the correct mask is set. This
causes probe to fail initialization of the cmdif SW structs on s390x
after that is converted to the common dma-iommu code. This is because on
s390x DMA addresses below 4 GiB are reserved on current machines and
unlike the old s390x specific DMA API implementation common code
enforces DMA masks.
Fix it by performing the DMA operations during probe after
pci_enable_device() and after the dma mask is set,
and during teardown before pci_disable_device().
[1]
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: xt_MASQUERADE nf_conntrack_netlink
nfnetlink xfrm_user iptable_nat xt_addrtype xt_conntrack nf_nat
nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 netconsole rpcsec_gss_krb5
auth_rpcgss oid_registry overlay rpcrdma rdma_ucm ib_iser ib_umad
rdma_cm ib_ipoib iw_cm libiscsi scsi_transport_iscsi ib_cm ib_uverbs
ib_core mlx5_core(-) ptp pps_core fuse vmx_crypto crc32c_vpmsum [last
unloaded: mlx5_ib]
CPU: 1 PID: 8937 Comm: modprobe Not tainted 6.5.0-rc3_for_upstream_min_debug_2023_07_31_16_02 #1
Hardware name: IBM pSeries (emulated by qemu) POWER9 (raw) 0x4e1202 0xf000005 of:SLOF,HEAD hv:linux,kvm pSeries
NIP: c000000000423388 LR: c0000000001e733c CTR: c0000000001e4720
REGS: c0000000055636d0 TRAP: 0380 Not tainted (6.5.0-rc3_for_upstream_min_debug_2023_07_31_16_02)
MSR: 8000000000009033 CR: 24008884 XER: 20040000
CFAR: c0000000001e7338 IRQMASK: 0
NIP [c000000000423388] __free_pages+0x28/0x160
LR [c0000000001e733c] dma_direct_free+0xac/0x190
Call Trace:
[c000000005563970] [5deadbeef0000100] 0x5deadbeef0000100 (unreliable)
[c0000000055639b0] [c0000000003d46cc] kfree+0x7c/0x150
[c000000005563a40] [c0000000001e47c8] dma_free_attrs+0xa8/0x1a0
[c000000005563aa0] [c008000000d0064c] mlx5_cmd_cleanup+0xa4/0x100 [mlx5_core]
[c000000005563ad0] [c008000000cf629c] mlx5_mdev_uninit+0xf4/0x140 [mlx5_core]
[c000000005563b00] [c008000000cf6448] remove_one+0x160/0x1d0 [mlx5_core]
[c000000005563b40] [c000000000958540] pci_device_remove+0x60/0x110
[c000000005563b80] [c000000000a35e80] device_remove+0x70/0xd0
[c000000005563bb0] [c000000000a37a38] device_release_driver_internal+0x2a8/0x330
[c000000005563c00] [c000000000a37b8c] driver_detach+0x8c/0x160
[c000000005563c40] [c000000000a35350] bus_remove_driver+0x90/0x110
[c000000005563c80] [c000000000a38948] driver_unregister+0x48/0x90
[c000000005563cf0] [c000000000957e38] pci_unregister_driver+0x38/0x150
[c000000005563d40] [c008000000eb6140] mlx5_cleanup+0x38/0x90 [mlx5_core]
Fixes: 06cd555f73ca ("net/mlx5: split mlx5_cmd_init() to probe and reload routines")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Tested-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The phy_power_off() should not be called if phy_power_on() failed.
So, add a condition .power_count before calls phy_power_off().
Fixes: 5cb630925b49 ("net: renesas: rswitch: Add phy_power_{on,off}() calling")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Fix functions calling order and a condition in renesas_eth_sw_remove().
Otherwise, kernel NULL pointer dereference happens from phy_stop() if
a net device opens.
Fixes: 3590918b5d07 ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Since page pool param's "order" is set to 0, will result
in below warn message if interface is configured with higher
rx buffer size.
Steps to reproduce the issue.
1. devlink dev param set pci/0002:04:00.0 name receive_buffer_size \
value 8196 cmode runtime
2. ifconfig eth0 up
[ 19.901356] ------------[ cut here ]------------
[ 19.901361] WARNING: CPU: 11 PID: 12331 at net/core/page_pool.c:567 page_pool_alloc_frag+0x3c/0x230
[ 19.901449] pstate: 82401009 (Nzcv daif +PAN -UAO +TCO -DIT +SSBS BTYPE=--)
[ 19.901451] pc : page_pool_alloc_frag+0x3c/0x230
[ 19.901453] lr : __otx2_alloc_rbuf+0x60/0xbc [rvu_nicpf]
[ 19.901460] sp : ffff80000f66b970
[ 19.901461] x29: ffff80000f66b970 x28: 0000000000000000 x27: 0000000000000000
[ 19.901464] x26: ffff800000d15b68 x25: ffff000195b5c080 x24: ffff0002a5a32dc0
[ 19.901467] x23: ffff0001063c0878 x22: 0000000000000100 x21: 0000000000000000
[ 19.901469] x20: 0000000000000000 x19: ffff00016f781000 x18: 0000000000000000
[ 19.901472] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000
[ 19.901474] x14: 0000000000000000 x13: ffff0005ffdc9c80 x12: 0000000000000000
[ 19.901477] x11: ffff800009119a38 x10: 4c6ef2e3ba300519 x9 : ffff800000d13844
[ 19.901479] x8 : ffff0002a5a33cc8 x7 : 0000000000000030 x6 : 0000000000000030
[ 19.901482] x5 : 0000000000000005 x4 : 0000000000000000 x3 : 0000000000000a20
[ 19.901484] x2 : 0000000000001080 x1 : ffff80000f66b9d4 x0 : 0000000000001000
[ 19.901487] Call trace:
[ 19.901488] page_pool_alloc_frag+0x3c/0x230
[ 19.901490] __otx2_alloc_rbuf+0x60/0xbc [rvu_nicpf]
[ 19.901494] otx2_rq_aura_pool_init+0x1c4/0x240 [rvu_nicpf]
[ 19.901498] otx2_open+0x228/0xa70 [rvu_nicpf]
[ 19.901501] otx2vf_open+0x20/0xd0 [rvu_nicvf]
[ 19.901504] __dev_open+0x114/0x1d0
[ 19.901507] __dev_change_flags+0x194/0x210
[ 19.901510] dev_change_flags+0x2c/0x70
[ 19.901512] devinet_ioctl+0x3a4/0x6c4
[ 19.901515] inet_ioctl+0x228/0x240
[ 19.901518] sock_ioctl+0x2ac/0x480
[ 19.901522] __arm64_sys_ioctl+0x564/0xe50
[ 19.901525] invoke_syscall.constprop.0+0x58/0xf0
[ 19.901529] do_el0_svc+0x58/0x150
[ 19.901531] el0_svc+0x30/0x140
[ 19.901533] el0t_64_sync_handler+0xe8/0x114
[ 19.901535] el0t_64_sync+0x1a0/0x1a4
[ 19.901537] ---[ end trace 678c0bf660ad8116 ]---
Fixes: b2e3406a38f0 ("octeontx2-pf: Add support for page pool")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Link: https://lore.kernel.org/r/20231010034842.3807816-1-rkannoth@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wpan/wpan
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2023-10-10
Just one small fix this time around.
Dinghao Liu fixed a potential use-after-free in the ca8210 driver probe
function.
* tag 'ieee802154-for-net-2023-10-10' of git://git.kernel.org/pub/scm/linux/kernel/git/wpan/wpan:
ieee802154: ca8210: Fix a potential UAF in ca8210_probe
====================
Link: https://lore.kernel.org/r/20231010200943.82225-1-stefan@datenfreihafen.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When there are CT table entries, and you rmmod nfp, the following
events can happen:
task1：
nfp_net_pci_remove
↓
nfp_flower_stop->(asynchronous)tcf_ct_flow_table_cleanup_work(3)
↓
nfp_zone_table_entry_destroy(1)
task2：
nfp_fl_ct_handle_nft_flow(2)
When the execution order is (1)->(2)->(3), it will crash. Therefore, in
the function nfp_fl_ct_del_flow, nf_flow_table_offload_del_cb needs to
be executed synchronously.
At the same time, in order to solve the deadlock problem and the problem
of rtnl_lock sometimes failing, replace rtnl_lock with the private
nfp_fl_lock.
Fixes: 7cc93d888df7 ("nfp: flower-ct: remove callback delete deadlock")
Cc: stable@vger.kernel.org
Signed-off-by: Yanguo Li <yanguo.li@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot has found an uninit-value bug triggered by the dm9601 driver [1].
This error happens because the variable res is not updated if the call
to dm_read_shared_word returns an error. In this particular case -EPROTO
was returned and res stayed uninitialized.
This can be avoided by checking the return value of dm_read_shared_word
and propagating the error if the read operation failed.
[1] https://syzkaller.appspot.com/bug?extid=1f53a30781af65d2c955
Cc: stable@vger.kernel.org
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reported-and-tested-by: syzbot+1f53a30781af65d2c955@syzkaller.appspotmail.com
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Fixes: d0374f4f9c35cdfbee0 ("USB: Davicom DM9601 usbnet driver")
Link: https://lore.kernel.org/r/20231009-topic-dm9601_uninit_mdio_read-v2-1-f2fe39739b6c@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2023-10-09
Lukas Magel's patch for the CAN ISO-TP protocol fixes the TX state
detection and wait behavior.
John Watts contributes a patch to only show the sun4i_can Kconfig
option on ARCH_SUNXI.
A patch by Miquel Raynal fixes the soft-reset workaround for Renesas
SoCs in the sja1000 driver.
Markus Schneider-Pargmann's patch for the tcan4x5x m_can glue driver
fixes the id2 register for the tcan4553.
2 patches by Haibo Chen fix the flexcan stop mode for the imx93 SoC.
* tag 'linux-can-fixes-for-6.6-20231009' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: tcan4x5x: Fix id2_register for tcan4553
can: flexcan: remove the auto stop mode for IMX93
can: sja1000: Always restart the Tx queue after an overrun
arm64: dts: imx93: add the Flex-CAN stop mode by GPR
can: sun4i_can: Only show Kconfig if ARCH_SUNXI is set
can: isotp: isotp_sendmsg(): fix TX state detection and wait behavior
====================
Link: https://lore.kernel.org/r/20231009085256.693378-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 1e66220948df8 ("net/mlx5e: Update rx ring hw mtu upon each rx-fcs
flag change") seems to have accidentally inverted the logic added in
commit 0bc73ad46a76 ("net/mlx5e: Mutually exclude RX-FCS and
RX-port-timestamp").
The impact of this is a little unclear since it seems the FCS scattered
with RX-FCS is (usually?) correct regardless.
Fixes: 1e66220948df8 ("net/mlx5e: Update rx ring hw mtu upon each rx-fcs flag change")
Tested-by: Charlotte Tan <charlotte@extrahop.com>
Reviewed-by: Charlotte Tan <charlotte@extrahop.com>
Cc: Adham Faris <afaris@nvidia.com>
Cc: Aya Levin <ayal@nvidia.com>
Cc: Tariq Toukan <tariqt@nvidia.com>
Cc: Moshe Shemesh <moshe@nvidia.com>
Cc: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Will Mortensen <will@extrahop.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20231006053706.514618-1-will@extrahop.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The adapter->vf_mvs.l list needs to be initialized even if the list is
empty. Otherwise it will lead to crashes.
Fixes: a1cbb15c1397 ("ixgbe: Add macvlan support for VF")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/ZSADNdIw8zFx1xw2@kadam
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When updating the SA, use the new update_pn flags instead of comparing the
new PN with the initial one.
Comparing the initial PN value with the new value will allow the user
to update the SA using the initial PN value as a parameter like this:
$ ip macsec add macsec0 tx sa 0 pn 1 on key 00 \
ead3664f508eb06c40ac7104cdae4ce5
$ ip macsec set macsec0 tx sa 0 pn 1 off
Fixes: 8ff0ac5be144 ("net/mlx5: Add MACsec offload Tx command support")
Fixes: aae3454e4d4c ("net/mlx5e: Add MACsec offload Rx command support")
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Updating the PN is not supported.
Return -EINVAL if update_pn is true.
The following command succeeded, but it should fail because the driver
does not update the PN:
ip macsec set macsec0 tx sa 0 pn 232 on
Fixes: 28c5107aa904 ("net: phy: mscc: macsec support")
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When updating SA, update the PN only when the update_pn flag is true.
Otherwise, the PN will be reset to its previous value using the
following command and this should not happen:
$ ip macsec set macsec0 tx sa 0 on
Fixes: c54ffc73601c ("octeontx2-pf: mcs: Introduce MACSEC hardware offloading")
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Indicate next PN update using update_pn flag in macsec_context.
Offloaded MACsec implementations does not know whether or not the
MACSEC_SA_ATTR_PN attribute was passed for an SA update and assume
that next PN should always updated, but this is not always true.
The PN can be reset to its initial value using the following command:
$ ip macsec set macsec0 tx sa 0 off #octeontx2-pf case
Or, the update PN command will succeed even if the driver does not support
PN updates.
$ ip macsec set macsec0 tx sa 0 pn 1 on #mscc phy driver case
Comparing the initial PN with the new PN value is not a solution. When
the user updates the PN using its initial value the command will
succeed, even if the driver does not support it. Like this:
$ ip macsec add macsec0 tx sa 0 pn 1 on key 00 \
ead3664f508eb06c40ac7104cdae4ce5
$ ip macsec set macsec0 tx sa 0 pn 1 on #mlx5 case
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When one of the LAG interfaces is in switchdev mode, setting default rule
can't be done.
The interface on which switchdev is running has ice_set_rx_mode() blocked
to avoid default rule adding (and other rules). The other interfaces
(without switchdev running but connected via bond with interface that
runs switchdev) can't follow the same scheme, because rx filtering needs
to be disabled when failover happens. Notification for bridge to set
promisc mode seems like good place to do that.
Fixes: bb52f42acef6 ("ice: Add driver support for firmware changes for LAG")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do not set netback interfaces (vifs) default TX queue size to the ring size.
The TX queue size is not related to the ring size, and using the ring size (32)
as the queue size can lead to packet drops. Note the TX side of the vif
interface in the netback domain is the one receiving packets to be injected
to the guest.
Do not explicitly set the TX queue length to any value when creating the
interface, and instead use the system default. Note that the queue length can
also be adjusted at runtime.
Fixes: f942dc2552b8 ('xen network backend driver')
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mlxsw_sp2_nve_vxlan_learning_set() function is supposed to return
zero on success or negative error codes. So it needs to be type int
instead of bool.
Fixes: 4ee70efab68d ("mlxsw: spectrum_nve: Add support for VXLAN on Spectrum-2")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If of_clk_add_provider() fails in ca8210_register_ext_clock(),
it calls clk_unregister() to release priv->clk and returns an
error. However, the caller ca8210_probe() then calls ca8210_remove(),
where priv->clk is freed again in ca8210_unregister_ext_clock(). In
this case, a use-after-free may happen in the second time we call
clk_unregister().
Fix this by removing the first clk_unregister(). Also, priv->clk could
be an error code on failure of clk_register_fixed_rate(). Use
IS_ERR_OR_NULL to catch this case in ca8210_unregister_ext_clock().
Fixes: ded845a781a5 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Message-ID: <20231007033049.22353-1-dinghao.liu@zju.edu.cn>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
|
|
The ravb_stop() should call cancel_work_sync(). Otherwise,
ravb_tx_timeout_work() is possible to use the freed priv after
ravb_remove() was called like below:
CPU0 CPU1
ravb_tx_timeout()
ravb_remove()
unregister_netdev()
free_netdev(ndev)
// free priv
ravb_tx_timeout_work()
// use priv
unregister_netdev() will call .ndo_stop() so that ravb_stop() is
called. And, after phy_stop() is called, netif_carrier_off()
is also called. So that .ndo_tx_timeout() will not be called
after phy_stop().
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Reported-by: Zheng Wang <zyytlz.wz@163.com>
Closes: https://lore.kernel.org/netdev/20230725030026.1664873-1-zyytlz.wz@163.com/
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20231005011201.14368-3-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In ravb_remove(), dma_free_coherent() should be call after
unregister_netdev(). Otherwise, this controller is possible to use
the freed buffer.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20231005011201.14368-2-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
IMX93 A0 chip involve the internal q-channel handshake in LPCG and
CCM to automatically handle the Flex-CAN IPG STOP signal. Only after
FLEX-CAN enter stop mode then can support the self-wakeup feature.
But meet issue when do the continue system PM stress test. When config
the CAN as wakeup source, the first time after system suspend, any data
on CAN bus can wakeup the system, this is as expect. But the second time
when system suspend, data on CAN bus can't wakeup the system. If continue
this test, we find in odd time system enter suspend, CAN can wakeup the
system, but in even number system enter suspend, CAN can't wakeup the
system. IC find a bug in the auto stop mode logic, and can't fix it easily.
So for the new imx93 A1, IC drop the auto stop mode and involve the
GPR to support stop mode (used before). IC define a bit in GPR which can
trigger the IPG STOP signal to Flex-CAN, let it go into stop mode.
And NXP claim to drop IMX93 A0, and only support IMX93 A1. So this patch
remove the auto stop mode, and add flag FLEXCAN_QUIRK_SETUP_STOP_MODE_GPR
to imx93.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/all/20230726112458.3524165-2-haibo.chen@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Fix id2_register content for tcan4553. This slipped through my testing.
Reported-by: Sean Anderson <sean.anderson@seco.com>
Closes: https://lore.kernel.org/lkml/a94e6fc8-4f08-7877-2ba0-29b9c2780136@seco.com/
Fixes: 142c6dc6d9d7 ("can: tcan4x5x: Add support for tcan4552/4553")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/all/20230919095401.1312259-1-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Upstream commit 717c6ec241b5 ("can: sja1000: Prevent overrun stalls with
a soft reset on Renesas SoCs") fixes an issue with Renesas own SJA1000
CAN controller reception: the Rx buffer is only 5 messages long, so when
the bus loaded (eg. a message every 50us), overrun may easily
happen. Upon an overrun situation, due to a possible internal crosstalk
situation, the controller enters a frozen state which only can be
unlocked with a soft reset (experimentally). The solution was to offload
a call to sja1000_start() in a threaded handler. This needs to happen in
process context as this operation requires to sleep. sja1000_start()
basically enters "reset mode", performs a proper software reset and
returns back into "normal mode".
Since this fix was introduced, we no longer observe any stalls in
reception. However it was sporadically observed that the transmit path
would now freeze. Further investigation blamed the fix mentioned above,
and especially the reset operation. Reproducing the reset in a loop
helped identifying what could possibly go wrong. The sja1000 is a single
Tx queue device, which leverages the netdev helpers to process one Tx
message at a time. The logic is: the queue is stopped, the message sent
to the transceiver, once properly transmitted the controller sets a
status bit which triggers an interrupt, in the interrupt handler the
transmission status is checked and the queue woken up. Unfortunately, if
an overrun happens, we might perform the soft reset precisely between
the transmission of the buffer to the transceiver and the advent of the
transmission status bit. We would then stop the transmission operation
without re-enabling the queue, leading to all further transmissions to
be ignored.
The reset interrupt can only happen while the device is "open", and
after a reset we anyway want to resume normal operations, no matter if a
packet to transmit got dropped in the process, so we shall wake up the
queue. Restarting the device and waking-up the queue is exactly what
sja1000_set_mode(CAN_MODE_START) does. In order to be consistent about
the queue state, we must acquire a lock both in the reset handler and in
the transmit path to ensure serialization of both operations. It turns
out, a lock is already held when entering the transmit path, so we can
just acquire/release it as well with the regular net helpers inside the
threaded interrupt handler and this way we should be safe. As the
reset handler might still be called after the transmission of a frame to
the transceiver but before it actually gets transmitted, we must ensure
we don't leak the skb, so we free it (the behavior is consistent, no
matter if there was an skb on the stack or not).
Fixes: 717c6ec241b5 ("can: sja1000: Prevent overrun stalls with a soft reset on Renesas SoCs")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/all/20231002160206.190953-1-miquel.raynal@bootlin.com
[mkl: fixed call to can_free_echo_skb()]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When adding the RISCV option I didn't gate it behind ARCH_SUNXI.
As a result this option shows up with Allwinner support isn't enabled.
Fix that by requiring ARCH_SUNXI to be set if RISCV is set.
Fixes: 8abb95250ae6 ("can: sun4i_can: Add support for the Allwinner D1")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/linux-sunxi/CAMuHMdV2m54UAH0X2dG7stEg=grFihrdsz4+o7=_DpBMhjTbkw@mail.gmail.com/
Signed-off-by: John Watts <contact@jookia.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/all/20230905231342.2042759-2-contact@jookia.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
PHYs via management frames
Besides the QCA8337 switch the Turris 1.x device has on it's MDIO bus
also Micron ethernet PHY (dedicated to the WAN port).
We've been experiencing a strange behavior of the WAN ethernet
interface, wherein the WAN PHY started timing out the MDIO accesses, for
example when the interface was brought down and then back up.
Bisecting led to commit 2cd548566384 ("net: dsa: qca8k: add support for
phy read/write with mgmt Ethernet"), which added support to access the
QCA8337 switch's internal PHYs via management ethernet frames.
Connecting the MDIO bus pins onto an oscilloscope, I was able to see
that the MDIO bus was active whenever a request to read/write an
internal PHY register was done via an management ethernet frame.
My theory is that when the switch core always communicates with the
internal PHYs via the MDIO bus, even when externally we request the
access via ethernet. This MDIO bus is the same one via which the switch
and internal PHYs are accessible to the board, and the board may have
other devices connected on this bus. An ASCII illustration may give more
insight:
+---------+
+----| |
| | WAN PHY |
| +--| |
| | +---------+
| |
| | +----------------------------------+
| | | QCA8337 |
MDC | | | +-------+ |
------o-+--|--------o------------o--| | |
MDIO | | | | | PHY 1 |-|--to RJ45
--------o--|---o----+---------o--+--| | |
| | | | | +-------+ |
| +-------------+ | o--| | |
| | MDIO MDC | | | | PHY 2 |-|--to RJ45
eth1 | | | o--+--| | |
-----------|-|port0 | | | +-------+ |
| | | | o--| | |
| | switch core | | | | PHY 3 |-|--to RJ45
| +-------------+ o--+--| | |
| | | +-------+ |
| | o--| ... | |
+----------------------------------+
When we send a request to read an internal PHY register via an ethernet
management frame via eth1, the switch core receives the ethernet frame
on port 0 and then communicates with the internal PHY via MDIO. At this
time, other potential devices, such as the WAN PHY on Turris 1.x, cannot
use the MDIO bus, since it may cause a bus conflict.
Fix this issue by locking the MDIO bus even when we are accessing the
PHY registers via ethernet management frames.
Fixes: 2cd548566384 ("net: dsa: qca8k: add support for phy read/write with mgmt Ethernet")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit c766e077d927 ("net: dsa: qca8k: convert to regmap read/write
API") introduced bulk read/write methods to qca8k's regmap.
The regmap bulk read/write methods get the register address in a buffer
passed as a void pointer parameter (the same buffer contains also the
read/written values). The register address occupies only as many bytes
as it requires at the beginning of this buffer. For example if the
.reg_bits member in regmap_config is 16 (as is the case for this
driver), the register address occupies only the first 2 bytes in this
buffer, so it can be cast to u16.
But the original commit implementing these bulk read/write methods cast
the buffer to u32:
u32 reg = *(u32 *)reg_buf & U16_MAX;
taking the first 4 bytes. This works on little endian systems where the
first 2 bytes of the buffer correspond to the low 16-bits, but it
obviously cannot work on big endian systems.
Fix this by casting the beginning of the buffer to u16 as
u32 reg = *(u16 *)reg_buf;
Fixes: c766e077d927 ("net: dsa: qca8k: convert to regmap read/write API")
Signed-off-by: Marek Behún <kabel@kernel.org>
Tested-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using netconsole netpoll_poll_dev could be called from interrupt
context, thus using disable_irq() would cause the following kernel
warning with CONFIG_DEBUG_ATOMIC_SLEEP enabled:
BUG: sleeping function called from invalid context at kernel/irq/manage.c:137
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 10, name: ksoftirqd/0
CPU: 0 PID: 10 Comm: ksoftirqd/0 Tainted: G W 5.15.42-00075-g816b502b2298-dirty #117
Hardware name: aml (r1) (DT)
Call trace:
dump_backtrace+0x0/0x270
show_stack+0x14/0x20
dump_stack_lvl+0x8c/0xac
dump_stack+0x18/0x30
___might_sleep+0x150/0x194
__might_sleep+0x64/0xbc
synchronize_irq+0x8c/0x150
disable_irq+0x2c/0x40
stmmac_poll_controller+0x140/0x1a0
netpoll_poll_dev+0x6c/0x220
netpoll_send_skb+0x308/0x390
netpoll_send_udp+0x418/0x760
write_msg+0x118/0x140 [netconsole]
console_unlock+0x404/0x500
vprintk_emit+0x118/0x250
dev_vprintk_emit+0x19c/0x1cc
dev_printk_emit+0x90/0xa8
__dev_printk+0x78/0x9c
_dev_warn+0xa4/0xbc
ath10k_warn+0xe8/0xf0 [ath10k_core]
ath10k_htt_txrx_compl_task+0x790/0x7fc [ath10k_core]
ath10k_pci_napi_poll+0x98/0x1f4 [ath10k_pci]
__napi_poll+0x58/0x1f4
net_rx_action+0x504/0x590
_stext+0x1b8/0x418
run_ksoftirqd+0x74/0xa4
smpboot_thread_fn+0x210/0x3c0
kthread+0x1fc/0x210
ret_from_fork+0x10/0x20
Since [0] .ndo_poll_controller is only needed if driver doesn't or
partially use NAPI. Because stmmac does so, stmmac_poll_controller
can be removed fixing the above warning.
[0] commit ac3d9dd034e5 ("netpoll: make ndo_poll_controller() optional")
Cc: <stable@vger.kernel.org> # 5.15.x
Fixes: 47dd7a540b8a ("net: add support for STMicroelectronics Ethernet controllers")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/1c156a6d8c9170bd6a17825f2277115525b4d50f.1696429960.git.repk@triplefau.lt
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since FIXED_PHY depends on PHYLIB, PHYLIB needs to be set to avoid
a kconfig warning:
WARNING: unmet direct dependencies detected for FIXED_PHY
Depends on [n]: NETDEVICES [=y] && PHYLIB [=n]
Selected by [y]:
- LAN743X [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_MICROCHIP [=y] && PCI [=y] && PTP_1588_CLOCK_OPTIONAL [=y]
Fixes: 73c4d1b307ae ("net: lan743x: select FIXED_PHY")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: lore.kernel.org/r/202309261802.JPbRHwti-lkp@intel.com
Cc: Bryan Whitehead <bryan.whitehead@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org> # build-tested
Link: https://lore.kernel.org/r/20231002193544.14529-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
While searching for possible refactor of napi_schedule_prep and
__napi_schedule it was notice that the mtk eth driver disable the
interrupt for rx and tx AFTER napi is scheduled.
While this is a very hard to repro case it might happen to have
situation where the interrupt is disabled and never enabled again as the
napi completes and the interrupt is enabled before.
This is caused by the fact that a napi driven by interrupt expect a
logic with:
1. interrupt received. napi prepared -> interrupt disabled -> napi
scheduled
2. napi triggered. ring cleared -> interrupt enabled -> wait for new
interrupt
To prevent this case, disable the interrupt BEFORE the napi is
scheduled.
Fixes: 656e705243fd ("net-next: mediatek: add support for MT7623 ethernet")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20231002140805.568-1-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Handle the case when GSO SKB linear length is too large.
MANA NIC requires GSO packets to put only the header part to SGE0,
otherwise the TX queue may stop at the HW level.
So, use 2 SGEs for the skb linear part which contains more than the
packet header.
Fixes: ca9c54d2d6a5 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
sizeof(struct hop_jumbo_hdr) is not part of tso_bytes, so remove
the subtraction from header size.
Cc: stable@vger.kernel.org
Fixes: bd7fc6e1957c ("net: mana: Add new MANA VF performance counters for easier troubleshooting")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
For an unknown TX CQE error type (probably from a newer hardware),
still free the SKB, update the queue tail, etc., otherwise the
accounting will be wrong.
Also, TX errors can be triggered by injecting corrupted packets, so
replace the WARN_ONCE to ratelimited error logging.
Cc: stable@vger.kernel.org
Fixes: ca9c54d2d6a5 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The STM32MP1 keeps clk_rx enabled during suspend, and therefore the
driver does not enable the clock in stm32_dwmac_init() if the device was
suspended. The problem is that this same code runs on STM32 MCUs, which
do disable clk_rx during suspend, causing the clock to never be
re-enabled on resume.
This patch adds a variant flag to indicate that clk_rx remains enabled
during suspend, and uses this to decide whether to enable the clock in
stm32_dwmac_init() if the device was suspended.
This approach fixes this specific bug with limited opportunity for
unintended side-effects, but I have a follow up patch that will refactor
the clock configuration and hopefully make it less error prone.
Fixes: 6528e02cc9ff ("net: ethernet: stmmac: add adaptation for stm32mp157c.")
Signed-off-by: Ben Wolsieffer <ben.wolsieffer@hefring.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230927175749.1419774-1-ben.wolsieffer@hefring.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
Quite a collection of fixes this time, really too many
to list individually. Many stack fixes, even rfkill
(found by simulation and the new eevdf scheduler)!
Also a bigger maintainers file cleanup, to remove old
and redundant information.
* tag 'wireless-2023-09-27' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless: (32 commits)
wifi: iwlwifi: mvm: Fix incorrect usage of scan API
wifi: mac80211: Create resources for disabled links
wifi: cfg80211: avoid leaking stack data into trace
wifi: mac80211: allow transmitting EAPOL frames with tainted key
wifi: mac80211: work around Cisco AP 9115 VHT MPDU length
wifi: cfg80211: Fix 6GHz scan configuration
wifi: mac80211: fix potential key leak
wifi: mac80211: fix potential key use-after-free
wifi: mt76: mt76x02: fix MT76x0 external LNA gain handling
wifi: brcmfmac: Replace 1-element arrays with flexible arrays
wifi: mwifiex: Fix oob check condition in mwifiex_process_rx_packet
wifi: rtw88: rtw8723d: Fix MAC address offset in EEPROM
rfkill: sync before userspace visibility/changes
wifi: mac80211: fix mesh id corruption on 32 bit systems
wifi: cfg80211: add missing kernel-doc for cqm_rssi_work
wifi: cfg80211: fix cqm_config access race
wifi: iwlwifi: mvm: Fix a memory corruption issue
wifi: iwlwifi: Ensure ack flag is properly cleared.
wifi: iwlwifi: dbg_ini: fix structure packing
iwlwifi: mvm: handle PS changes in vif_cfg_changed
...
====================
Link: https://lore.kernel.org/r/20230927095835.25803-2-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In some OVS environments the TCP pseudo header checksum may need to be
recomputed. Currently this is only done when the interface instance is
configured for "Trunk Mode". We found the issue also occurs in some
Kubernetes environments, these environments do not use "Trunk Mode",
therefor the condition is removed.
Performance tests with this change show only a fractional decrease in
throughput (< 0.2%).
Fixes: 7525de2516fb ("ibmveth: Set CHECKSUM_PARTIAL if NULL TCP CSUM.")
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Reviewed-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The k3_udma_glue_tx_get_irq() function currently returns negative error
codes on error, zero on error and positive values for success. This
complicates life for the callers who need to propagate the error code.
Also GCC will not warn about unsigned comparisons when you check:
if (unsigned_irq <= 0)
All the callers have been fixed now but let's just make this easy going
forward.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "tx_chn->irq" variable is unsigned so the error checking does not
work correctly.
Fixes: 128d5874c082 ("net: ti: icssg-prueth: Add ICSSG ethernet driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This accidentally returns success, but it should return a negative error
code.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the MPIC.PSMCS value following the programming example in the
section 6.4.2 Management Data Clock (MDC) Setting, Ethernet MAC IP,
S4 Hardware User Manual Rev.1.00.
The value is calculated by
MPIC.PSMCS = clk[MHz] / (MDC frequency[MHz] * 2) - 1
with the input clock frequency from clk_get_rate() and MDC frequency
of 2.5MHz. Otherwise, this driver cannot communicate PHYs on the R-Car
S4 Starter Kit board.
Fixes: 3590918b5d07 ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Reported-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230926123054.3976752-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The flexible structure (a structure that contains a flexible-array member
at the end) `qed_ll2_tx_packet` is nested within the second layer of
`struct qed_ll2_info`:
struct qed_ll2_tx_packet {
...
/* Flexible Array of bds_set determined by max_bds_per_packet */
struct {
struct core_tx_bd *txq_bd;
dma_addr_t tx_frag;
u16 frag_len;
} bds_set[];
};
struct qed_ll2_tx_queue {
...
struct qed_ll2_tx_packet cur_completing_packet;
};
struct qed_ll2_info {
...
struct qed_ll2_tx_queue tx_queue;
struct qed_ll2_cbs cbs;
};
The problem is that member `cbs` in `struct qed_ll2_info` is placed just
after an object of type `struct qed_ll2_tx_queue`, which is in itself
an implicit flexible structure, which by definition ends in a flexible
array member, in this case `bds_set`. This causes an undefined behavior
bug at run-time when dynamic memory is allocated for `bds_set`, which
could lead to a serious issue if `cbs` in `struct qed_ll2_info` is
overwritten by the contents of `bds_set`. Notice that the type of `cbs`
is a structure full of function pointers (and a cookie :) ):
include/linux/qed/qed_ll2_if.h:
107 typedef
108 void (*qed_ll2_complete_rx_packet_cb)(void *cxt,
109 struct qed_ll2_comp_rx_data *data);
110
111 typedef
112 void (*qed_ll2_release_rx_packet_cb)(void *cxt,
113 u8 connection_handle,
114 void *cookie,
115 dma_addr_t rx_buf_addr,
116 bool b_last_packet);
117
118 typedef
119 void (*qed_ll2_complete_tx_packet_cb)(void *cxt,
120 u8 connection_handle,
121 void *cookie,
122 dma_addr_t first_frag_addr,
123 bool b_last_fragment,
124 bool b_last_packet);
125
126 typedef
127 void (*qed_ll2_release_tx_packet_cb)(void *cxt,
128 u8 connection_handle,
129 void *cookie,
130 dma_addr_t first_frag_addr,
131 bool b_last_fragment, bool b_last_packet);
132
133 typedef
134 void (*qed_ll2_slowpath_cb)(void *cxt, u8 connection_handle,
135 u32 opaque_data_0, u32 opaque_data_1);
136
137 struct qed_ll2_cbs {
138 qed_ll2_complete_rx_packet_cb rx_comp_cb;
139 qed_ll2_release_rx_packet_cb rx_release_cb;
140 qed_ll2_complete_tx_packet_cb tx_comp_cb;
141 qed_ll2_release_tx_packet_cb tx_release_cb;
142 qed_ll2_slowpath_cb slowpath_cb;
143 void *cookie;
144 };
Fix this by moving the declaration of `cbs` to the middle of its
containing structure `qed_ll2_info`, preventing it from being
overwritten by the contents of `bds_set` at run-time.
This bug was introduced in 2017, when `bds_set` was converted to a
one-element array, and started to be used as a Variable Length Object
(VLO) at run-time.
Fixes: f5823fe6897c ("qed: Add ll2 option to limit the number of bds per packet")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/ZQ+Nz8DfPg56pIzr@work
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
syzbot reported the following uninit-value access issue:
=====================================================
BUG: KMSAN: uninit-value in smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:975 [inline]
BUG: KMSAN: uninit-value in smsc75xx_bind+0x5c9/0x11e0 drivers/net/usb/smsc75xx.c:1482
CPU: 0 PID: 8696 Comm: kworker/0:3 Not tainted 5.8.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x21c/0x280 lib/dump_stack.c:118
kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:121
__msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215
smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:975 [inline]
smsc75xx_bind+0x5c9/0x11e0 drivers/net/usb/smsc75xx.c:1482
usbnet_probe+0x1152/0x3f90 drivers/net/usb/usbnet.c:1737
usb_probe_interface+0xece/0x1550 drivers/usb/core/driver.c:374
really_probe+0xf20/0x20b0 drivers/base/dd.c:529
driver_probe_device+0x293/0x390 drivers/base/dd.c:701
__device_attach_driver+0x63f/0x830 drivers/base/dd.c:807
bus_for_each_drv+0x2ca/0x3f0 drivers/base/bus.c:431
__device_attach+0x4e2/0x7f0 drivers/base/dd.c:873
device_initial_probe+0x4a/0x60 drivers/base/dd.c:920
bus_probe_device+0x177/0x3d0 drivers/base/bus.c:491
device_add+0x3b0e/0x40d0 drivers/base/core.c:2680
usb_set_configuration+0x380f/0x3f10 drivers/usb/core/message.c:2032
usb_generic_driver_probe+0x138/0x300 drivers/usb/core/generic.c:241
usb_probe_device+0x311/0x490 drivers/usb/core/driver.c:272
really_probe+0xf20/0x20b0 drivers/base/dd.c:529
driver_probe_device+0x293/0x390 drivers/base/dd.c:701
__device_attach_driver+0x63f/0x830 drivers/base/dd.c:807
bus_for_each_drv+0x2ca/0x3f0 drivers/base/bus.c:431
__device_attach+0x4e2/0x7f0 drivers/base/dd.c:873
device_initial_probe+0x4a/0x60 drivers/base/dd.c:920
bus_probe_device+0x177/0x3d0 drivers/base/bus.c:491
device_add+0x3b0e/0x40d0 drivers/base/core.c:2680
usb_new_device+0x1bd4/0x2a30 drivers/usb/core/hub.c:2554
hub_port_connect drivers/usb/core/hub.c:5208 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5348 [inline]
port_event drivers/usb/core/hub.c:5494 [inline]
hub_event+0x5e7b/0x8a70 drivers/usb/core/hub.c:5576
process_one_work+0x1688/0x2140 kernel/workqueue.c:2269
worker_thread+0x10bc/0x2730 kernel/workqueue.c:2415
kthread+0x551/0x590 kernel/kthread.c:292
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:293
Local variable ----buf.i87@smsc75xx_bind created at:
__smsc75xx_read_reg drivers/net/usb/smsc75xx.c:83 [inline]
smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:968 [inline]
smsc75xx_bind+0x485/0x11e0 drivers/net/usb/smsc75xx.c:1482
__smsc75xx_read_reg drivers/net/usb/smsc75xx.c:83 [inline]
smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:968 [inline]
smsc75xx_bind+0x485/0x11e0 drivers/net/usb/smsc75xx.c:1482
This issue is caused because usbnet_read_cmd() reads less bytes than requested
(zero byte in the reproducer). In this case, 'buf' is not properly filled.
This patch fixes the issue by returning -ENODATA if usbnet_read_cmd() reads
less bytes than requested.
Fixes: d0cad871703b ("smsc75xx: SMSC LAN75xx USB gigabit ethernet adapter driver")
Reported-and-tested-by: syzbot+6966546b78d050bb0b5d@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=6966546b78d050bb0b5d
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230923173549.3284502-1-syoshida@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In the pathological case of building sky2 with 16k PAGE_SIZE, the
frag_addr[] array would never be used, so the original code was correct
that size should be 0. But the compiler now gets upset with 0 size arrays
in places where it hasn't eliminated the code that might access such an
array (it can't figure out that in this case an rx skb with fragments
would never be created). To keep the compiler happy, make sure there is
at least 1 frag_addr in struct rx_ring_info:
In file included from include/linux/skbuff.h:28,
from include/net/net_namespace.h:43,
from include/linux/netdevice.h:38,
from drivers/net/ethernet/marvell/sky2.c:18:
drivers/net/ethernet/marvell/sky2.c: In function 'sky2_rx_unmap_skb':
include/linux/dma-mapping.h:416:36: warning: array subscript i is outside array bounds of 'dma_addr_t[0]' {aka 'long long unsigned int[]'} [-Warray-bounds=]
416 | #define dma_unmap_page(d, a, s, r) dma_unmap_page_attrs(d, a, s, r, 0)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/marvell/sky2.c:1257:17: note: in expansion of macro 'dma_unmap_page'
1257 | dma_unmap_page(&pdev->dev, re->frag_addr[i],
| ^~~~~~~~~~~~~~
In file included from drivers/net/ethernet/marvell/sky2.c:41:
drivers/net/ethernet/marvell/sky2.h:2198:25: note: while referencing 'frag_addr'
2198 | dma_addr_t frag_addr[ETH_JUMBO_MTU >> PAGE_SHIFT];
| ^~~~~~~~~
With CONFIG_PAGE_SIZE_16KB=y, PAGE_SHIFT == 14, so:
#define ETH_JUMBO_MTU 9000
causes "ETH_JUMBO_MTU >> PAGE_SHIFT" to be 0. Use "?: 1" to solve this build warning.
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202309191958.UBw1cjXk-lkp@intel.com/
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
