| Age | Commit message (Collapse) | Author |
|---|
|
On TJA1120, the external trigger timestamp now has a VALID bit. This
changes the logic and we can't use the TJA1103 procedure.
For TJA1103, we can always read a valid timestamp from the registers,
compare the new timestamp with the old timestamp and, if they are not the
same, an event occurred. This logic cannot be applied for TJA1120 because
the timestamp is 0 if the VALID bit is not set.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Link: https://lore.kernel.org/r/20230731091619.77961-11-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For TJA1120, the enable bit for cable test is not writable if the PHY is
not in test mode.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230731091619.77961-10-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
TJA1120 and TJA1103 have a set of functional safety hardware tests
executed after every reset, and when the tests are done, the IRQ line is
asserted. For the moment, the purpose of these handlers is to acknowledge
the IRQ and not to check the FUSA tests status.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230731091619.77961-9-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The egress timestamp FIFO/circular buffer work different on TJA1120 than
TJA1103.
For TJA1103 the new timestamp should be manually moved from the FIFO to
the hardware buffer before checking if the timestamp is valid.
For TJA1120 the hardware will move automatically the new timestamp
from the FIFO to the buffer and the user should check the valid bit, read
the timestamp and unlock the buffer by writing any of the buffer
registers(which are read only).
Another change for the TJA1120 is the behaviour of the EGR TS IRQ bit.
This bit was a self-clear bit for TJA1103, but now should be cleared
before reading the timestamp.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Link: https://lore.kernel.org/r/20230731091619.77961-8-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The external trigger configuration for TJA1120 has changed. The PHY
supports sampling of the LTC on rising and on falling edge.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230731091619.77961-7-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add TJA1120 driver entry and its driver_data.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230731091619.77961-6-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
PHY_BASIC_T1_FEATURES are not the right features supported by TJA1103
anymore.
For example ethtool reports:
[root@alarm ~]# ethtool end0
Settings for end0:
Supported ports: [ TP ]
Supported link modes: 100baseT1/Full
10baseT1L/Full
10baseT1L/Full is not supported by TJA1103 and supported ports list is
not completed. The PHY also have a MII port.
genphy_c45_pma_read_abilities implementation can detect the PHY features
and they look like this.
[root@alarm ~]# ethtool end0
Settings for end0:
Supported ports: [ TP MII ]
Supported link modes: 100baseT1/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 100baseT1/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 100Mb/s
Duplex: Full
Auto-negotiation: off
master-slave cfg: forced master
master-slave status: master
Port: Twisted Pair
PHYAD: 1
Transceiver: external
MDI-X: Unknown
Supports Wake-on: g
Wake-on: d
Link detected: yes
SQI: 7/7
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230731091619.77961-5-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Between TJA1120 and TJA1103 the hardware was improved, but some register
addresses were changed and some bit fields were moved from one register
to another.
Introduce the nxp_c45_reg_field structure and its associated functions to
abstract the differences between the PHYs.
Remove the defined bits and register addresses that are not common
between TJA1103 and TJA1120 and replace them with reg_fields and
register addresses from phydev->drv->driver_data.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Link: https://lore.kernel.org/r/20230731091619.77961-4-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove RX BIST frame counters from the PHY statistics.
In production mode, these counters are always read as 0.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230731091619.77961-3-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove the custom implementation of master/save setup and read status
and use genphy_c45_config_aneg and genphy_c45_read_status since phylib
has support for master/slave setup and master/slave status.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230731091619.77961-2-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Enable per queue interrupt coalesce feature bit in driver and validate its
dependency with control queue.
Signed-off-by: Gavin Li <gavinl@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20230731070656.96411-4-gavinl@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add interrupt_coalesce config in send_queue and receive_queue to cache user
config.
Send per virtqueue interrupt moderation config to underlying device in
order to have more efficient interrupt moderation and cpu utilization of
guest VM.
Additionally, address all the VQs when updating the global configuration,
as now the individual VQs configuration can diverge from the global
configuration.
Signed-off-by: Gavin Li <gavinl@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20230731070656.96411-3-gavinl@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Extract interrupt coalescing settings to a structure so that it could be
reused in other data structures.
Signed-off-by: Gavin Li <gavinl@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230731070656.96411-2-gavinl@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The existing code does not allow the MTU to be set to the maximum even
after an XDP program supporting multiple buffers is attached. Fix it
to set the netdev->max_mtu to the maximum value if the attached XDP
program supports mutiple buffers, regardless of the current MTU value.
Also use a local variable dev instead of repeatedly using bp->dev.
Fixes: 1dc4c557bfed ("bnxt: adding bnxt_xdp_build_skb to build skb from multibuffer xdp_buff")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20230731142043.58855-3-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The RXBD length field on all bnxt chips is 16-bit and so we cannot
support a full page when the native page size is 64K or greater.
The non-XDP (non page pool) code path has logic to handle this but
the XDP page pool code path does not handle this. Add the missing
logic to use page_pool_dev_alloc_frag() to allocate 32K chunks if
the page size is 64K or greater.
Fixes: 9f4b28301ce6 ("bnxt: XDP multibuffer enablement")
Link: https://lore.kernel.org/netdev/20230728231829.235716-2-michael.chan@broadcom.com/
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20230731142043.58855-2-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As documented in acd7aaf51b20 ("netsec: ignore 'phy-mode' device
property on ACPI systems") the SocioNext SynQuacer platform ships with
firmware defining the PHY mode as RGMII even though the physical
configuration of the PHY is for TX and RX delays. Since bbc4d71d63549bc
("net: phy: realtek: fix rtl8211e rx/tx delay config") this has caused
misconfiguration of the PHY, rendering the network unusable.
This was worked around for ACPI by ignoring the phy-mode property but
the system is also used with DT. For DT instead if we're running on a
SynQuacer force a working PHY mode, as well as the standard EDK2
firmware with DT there are also some of these systems that use u-boot
and might not initialise the PHY if not netbooting. Newer firmware
imagaes for at least EDK2 are available from Linaro so print a warning
when doing this.
Fixes: 533dd11a12f6 ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230731-synquacer-net-v3-1-944be5f06428@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
in korina_probe(), the return value of clk_prepare_enable()
should be checked since it might fail. we can use
devm_clk_get_optional_enabled() instead of devm_clk_get_optional()
and clk_prepare_enable() to automatically handle the error.
Fixes: e4cd854ec487 ("net: korina: Get mdio input clock via common clock framework")
Signed-off-by: Yuanjun Gong <ruc_gongyuanjun@163.com>
Link: https://lore.kernel.org/r/20230731090535.21416-1-ruc_gongyuanjun@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since zero-length arrays are deprecated, we are replacing
them with C99 flexible-array members. As a result, instead
of declaring a zero-length array, use the new
DECLARE_FLEX_ARRAY() helper macro.
This fixes warnings such as:
./drivers/net/ethernet/apple/macmace.c:80:4-8: WARNING use flexible-array member instead (https://www.kernel.org/doc/html/latest/process/deprecated.html#zero-length-and-one-element-arrays)
Signed-off-by: Atul Raut <rauji.raut@gmail.com>
Link: https://lore.kernel.org/r/20230730231442.15003-1-rauji.raut@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The SL-A300, B500/5600, and C700 devices no longer auto-load because of
"usbnet: Remove over-broad module alias from zaurus."
This patch adds IDs for those 3 devices.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217632
Fixes: 16adf5d07987 ("usbnet: Remove over-broad module alias from zaurus.")
Signed-off-by: Ross Maynard <bids.7405@bigpond.com>
Cc: stable@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/69b5423b-2013-9fc9-9569-58e707d9bafb@bigpond.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Most kernel functions return negative error codes but some irq functions
return zero on error. In this code irq_of_parse_and_map(), returns zero
and platform_get_irq() returns negative error codes. We need to handle
both cases appropriately.
Fixes: 8425c41d1ef7 ("net: ll_temac: Extend support to non-device-tree platforms")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Harini Katakam <harini.katakam@amd.com>
Link: https://lore.kernel.org/r/3d0aef75-06e0-45a5-a2a6-2cc4738d4143@moroto.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Prefer 'kstrtoX()' family of functions over 'sscanf()' to convert
strings to integers and always check results of the conversions.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230725060531.72968-6-dmantipov@yandex.ru
|
|
Check and handle (well, report at least, as it's done through the rest
of the module) possible 'spu_write_u16()' errors in 'if_spi_e2h()'.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230725060531.72968-5-dmantipov@yandex.ru
|
|
Embed SDIO reset worker in 'struct if_sdio_card' and so
drop 'reset_host' and 'card_reset_work' static variables,
adjust related code. Not sure whether it's possible to do
something useful on 'mmc_add_host()' error, so just add
'dev_err()' to emit an error message.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230725060531.72968-4-dmantipov@yandex.ru
|
|
Use 'list_for_each_entry_safe()' to simplify
list operations in 'free_if_spi_card()'.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230725060531.72968-3-dmantipov@yandex.ru
|
|
Use convenient lists to manage SDIO packets, adjust
'struct if_sdio_packet', 'struct if_sdio_card' and
related code accordingly.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230725060531.72968-2-dmantipov@yandex.ru
|
|
Add missing 'cancel_work_sync()' in 'if_sdio_remove()'
and on error handling path in 'if_sdio_probe()'.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Tested-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230725060531.72968-1-dmantipov@yandex.ru
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230724211914.805876-1-robh@kernel.org
|
|
In some situations like, chip wake-up with powersave enabled, SPI
commands are failing temporarily. Reissuing commands after reset helps
to overcome the failure. So, add the retry limit and reset command
sequence API for read/write SPI commands.
Signed-off-by: Amisha Patel <amisha.patel@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230724163955.4583-1-amisha.patel@microchip.com
|
|
Make sure mwifiex_process_mgmt_packet,
mwifiex_process_sta_rx_packet and mwifiex_process_uap_rx_packet,
mwifiex_uap_queue_bridged_pkt and mwifiex_process_rx_packet
not out-of-bounds access the skb->data buffer.
Fixes: 2dbaf751b1de ("mwifiex: report received management frames to cfg80211")
Signed-off-by: Polaris Pi <pinkperfect2021@gmail.com>
Reviewed-by: Matthew Wang <matthewmwang@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230723070741.1544662-1-pinkperfect2021@gmail.com
|
|
The 'enhance throughput flow' algorithm is used by default. So older
sections of the code are removed so as to always use this new algorithm.
Signed-off-by: Prasurjya Rohan Saikia <prasurjya.rohansaikia@microchip.com>
Acked-by: Ajay Kathat <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230710094401.235222-1-prasurjya.rohansaikia@microchip.com
|
|
The data rate from RX descriptor also uses hardware rate v1 for WiFi 7
chips. The rate code contains three parts -- mode, NSS and MCS. For
CCK/OFDM/HT rates, NSS/MCS parts are the same as before. VHT/HE/EHT rates
are changed and listed as below:
mode NSS MCS
V0 [8:7] [6:4] [3:0]
V1 [10:8] [7:5] [4:0]
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230728070252.66525-11-pkshih@realtek.com
|
|
The upcoming WiFi 7 chips support EHT rates, and hardware rate codes are
changed too, so modify to adapt the changes. (EHT counters are still zeros
in below example)
RX count:
Legacy: [0, 0, 0, 0]
OFDM: [0, 0, 0, 0, 0, 0, 0, 0]
HT 0: [0, 0, 0, 0, 0, 0, 0, 0]
HT 1: [0, 0, 0, 0, 0, 0, 0, 0]
VHT 1SS: [0, 0, 0, 0, 0, 0, 0, 0, 0, 0][0, 0]
VHT 2SS: [0, 0, 0, 0, 0, 0, 0, 0, 0, 0][0, 0]
HE 1SS: [0, 0, 42, 0, 43, 90, 75, 0, 26, 20, 260, 7]
HE 2SS: [0, 96, 232, 84, 125, 184, 52, 0, 0, 0, 0, 0]
EHT 1SS: [0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0][0, 0]
EHT 2SS: [0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0]
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230728070252.66525-10-pkshih@realtek.com
|
|
WiFi 7 chips have more rate mode (EHT), higher MCS and more bandwidth, so
define and use reserved bits to carry these information in C2H events.
Also, the SS/MCS encoded bits of VHT and HE are changed, so define V1 masks
for them.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230728070252.66525-9-pkshih@realtek.com
|
|
RA (rate adaptive), a mechanism to select proper rate, is implemented in
firmware, and this report is used to tell driver TX rate it is currently
using. Use struct to access this report, and doesn't change logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230728070252.66525-8-pkshih@realtek.com
|
|
Firmware C2H events contain two-word header which can indicate category,
class, function and length of received events. Use struct to access them,
and doesn't change logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230728070252.66525-7-pkshih@realtek.com
|
|
H2C RA V1 command adds two words to support WiFi 7 chips, which can
possibly support up to 4SS rates. Because current chips have only 2SS
rates, leave the fields blank for now. The main changes are to set
extended bits of EHT mode and bandwidth -- add a bit for EHT mode; add a
bit to enumerate 320MHz channel bandwidth.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230728070252.66525-6-pkshih@realtek.com
|
|
RA (rate adaptive) H2C command is used to tell firmware which rates can
be used for specified MAC ID. Basically, this commit doesn't change result.
Only change to set two 32-bit instead of continual 8-byte rate masks one
by one. Originally, we only set 5-byte masks, because existing WiFi 6
2SS chips only need 5-byte masks. Setting two 32-bit masks will be more
efficient and also can support coming WiFi 7 2SS chips containing more
rates.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230728070252.66525-5-pkshih@realtek.com
|
|
Rate pattern is controlled by 'iw bitrates' to fix rate as desired, and
we extend to support v1 rate.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230728070252.66525-4-pkshih@realtek.com
|
|
To support EHT rate, hardware rate v1 is introduced. The CCK and OFDM rates
are persistent. HT/VHT/HE rates use different rate code from original, and
add new code for EHT rates.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230728070252.66525-3-pkshih@realtek.com
|
|
The coming WiFi 7 chip is 8922AE which uses different hardware rate and
register naming rule. Adding a chip_info::chip_gen field can help to
do things by generations accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230728070252.66525-2-pkshih@realtek.com
|
|
When using compressed firmware, the early firmware load feature will fail.
In most cases, the only downside is that if a device has more than one
firmware version available, only the last one listed will be loaded.
In at least two cases, there is no firmware loaded, and the device fails
initialization. See https://github.com/lwfinger/rtw89/issues/259 and
https://bugzilla.opensuse.org/show_bug.cgi?id=1212808 for examples of
the failure.
When firmware_class.dyndbg=+p" added to the kernel boot parameters, the
following is found:
finger@localhost:~/rtw89>sudo dmesg -t | grep rtw89
firmware_class: __allocate_fw_priv: fw-rtw89/rtw8852b_fw-1.bin fw_priv=00000000638862fb
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/5.14.21-150500.53-default/rtw89/rtw8852b_fw-1.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/rtw89/rtw8852b_fw-1.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/5.14.21-150500.53-default/rtw89/rtw8852b_fw-1.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/rtw89/rtw8852b_fw-1.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: Direct firmware load for rtw89/rtw8852b_fw-1.bin failed with error -2
firmware_class: __free_fw_priv: fw-rtw89/rtw8852b_fw-1.bin fw_priv=00000000638862fb data=00000000307c30c7 size=0
firmware_class: __allocate_fw_priv: fw-rtw89/rtw8852b_fw.bin fw_priv=00000000638862fb
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/5.14.21-150500.53-default/rtw89/rtw8852b_fw.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/rtw89/rtw8852b_fw.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/5.14.21-150500.53-default/rtw89/rtw8852b_fw.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/rtw89/rtw8852b_fw.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: Direct firmware load for rtw89/rtw8852b_fw.bin failed with error -2
firmware_class: __free_fw_priv: fw-rtw89/rtw8852b_fw.bin fw_priv=00000000638862fb data=00000000307c30c7 size=0
rtw89_8852be 0000:02:00.0: failed to early request firmware: -2
firmware_class: __allocate_fw_priv: fw-rtw89/rtw8852b_fw.bin fw_priv=00000000638862fb
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/5.14.21-150500.53-default/rtw89/rtw8852b_fw.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/rtw89/rtw8852b_fw.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/5.14.21-150500.53-default/rtw89/rtw8852b_fw.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/rtw89/rtw8852b_fw.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/5.14.21-150500.53-default/rtw89/rtw8852b_fw.bin.xz failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/rtw89/rtw8852b_fw.bin.xz failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/5.14.21-150500.53-default/rtw89/rtw8852b_fw.bin.xz failed for no such file or directory.
rtw89_8852be 0000:02:00.0: Loading firmware from /lib/firmware/rtw89/rtw8852b_fw.bin.xz
rtw89_8852be 0000:02:00.0: f/w decompressing rtw89/rtw8852b_fw.bin
firmware_class: fw_set_page_data: fw-rtw89/rtw8852b_fw.bin fw_priv=00000000638862fb data=000000004ed6c2f7 size=1035232
rtw89_8852be 0000:02:00.0: Firmware version 0.27.32.1, cmd version 0, type 1
rtw89_8852be 0000:02:00.0: Firmware version 0.27.32.1, cmd version 0, type 3
The key is that firmware version 0.27.32.1 is loaded.
With this patch, the following is obtained:
firmware_class: __free_fw_priv: fw-rtw89/rtw8852b_fw.bin fw_priv=000000000849addc data=00000000fd3cabe2 size=1035232
firmware_class: fw_name_devm_release: fw_name-rtw89/rtw8852b_fw.bin devm-000000002d8c3343 released
firmware_class: __allocate_fw_priv: fw-rtw89/rtw8852b_fw-1.bin fw_priv=000000009e1a6364
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/6.4.3-1-default/rtw89/rtw8852b_fw-1.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/rtw89/rtw8852b_fw-1.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/6.4.3-1-default/rtw89/rtw8852b_fw-1.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/rtw89/rtw8852b_fw-1.bin failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/6.4.3-1-default/rtw89/rtw8852b_fw-1.bin.zst failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/rtw89/rtw8852b_fw-1.bin.zst failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/6.4.3-1-default/rtw89/rtw8852b_fw-1.bin.zst failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/rtw89/rtw8852b_fw-1.bin.zst failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/6.4.3-1-default/rtw89/rtw8852b_fw-1.bin.xz failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/updates/rtw89/rtw8852b_fw-1.bin.xz failed for no such file or directory.
rtw89_8852be 0000:02:00.0: loading /lib/firmware/6.4.3-1-default/rtw89/rtw8852b_fw-1.bin.xz failed for no such file or directory.
rtw89_8852be 0000:02:00.0: Loading firmware from /lib/firmware/rtw89/rtw8852b_fw-1.bin.xz
rtw89_8852be 0000:02:00.0: f/w decompressing rtw89/rtw8852b_fw-1.bin
firmware_class: fw_set_page_data: fw-rtw89/rtw8852b_fw-1.bin fw_priv=000000009e1a6364 data=00000000fd3cabe2 size=1184992
rtw89_8852be 0000:02:00.0: Loaded FW: rtw89/rtw8852b_fw-1.bin, sha256: 8539efc75f513f4585cf0cd6e79e6507da47fce87225f2d0de391a03aefe9ac8
rtw89_8852be 0000:02:00.0: loaded firmware rtw89/rtw8852b_fw-1.bin
rtw89_8852be 0000:02:00.0: Firmware version 0.29.29.1, cmd version 0, type 5
rtw89_8852be 0000:02:00.0: Firmware version 0.29.29.1, cmd version 0, type 3
Now, version 0.29.29.1 is loaded.
Fixes: ffde7f3476a6 ("wifi: rtw89: add firmware format version to backward compatible with older drivers")
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230724183927.28553-1-Larry.Finger@lwfinger.net
|
|
The trailing array member of struct tx_buf was defined as a 1-element
array, but used as a flexible array. This was resulting in build warnings:
In function 'fortify_memset_chk',
inlined from 'memset_io' at /kisskb/src/arch/mips/include/asm/io.h:486:2,
inlined from 'build_auth_frame' at /kisskb/src/drivers/net/wireless/legacy/ray_cs.c:2697:2:
/kisskb/src/include/linux/fortify-string.h:493:25: error: call to '__write_overflow_field' declared with attribute warning:
detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
493 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Replace it with an actual flexible array. Binary difference comparison
shows a single change in output:
│ drivers/net/wireless/legacy/ray_cs.c:883
│ lea 0x1c(%rbp),%r13d
│ - cmp $0x7c3,%r13d
│ + cmp $0x7c4,%r13d
This is from:
if (len + TX_HEADER_LENGTH > TX_BUF_SIZE) {
specifically:
#define TX_BUF_SIZE (2048 - sizeof(struct tx_msg))
This appears to have been originally buggy, so the change is correct.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/all/88f83d73-781d-bdc-126-aa629cb368c@linux-m68k.org
Cc: Kalle Valo <kvalo@kernel.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230728231245.never.309-kees@kernel.org
|
|
Convert for loop to dsa_for_each macro to save some redundant write on
unconnected/unused port and tidy things up.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230730074113.21889-5-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Move qca8xxx hol fixup to separate function to tidy things up and to
permit using a more efficent loop in future patch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230730074113.21889-4-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In preparation for multi-CPU support, set CPU port LOOKUP MEMBER outside
the port loop and setup the LOOKUP MEMBER mask for user ports only to
the first CPU port.
This is to handle flooding condition where every CPU port is set as
target and prevent packet duplication for unknown frames from user ports.
Secondary CPU port LOOKUP MEMBER mask will be setup later when
port_change_master will be implemented.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230730074113.21889-3-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Address learning should initially be turned off by the driver for port
operation in standalone mode, then the DSA core handles changes to it
via ds->ops->port_bridge_flags().
Currently this is not the case for qca8k where learning is enabled
unconditionally in qca8k_setup for every user port.
Handle ports configured in standalone mode by making the learning
configurable and not enabling it by default.
Implement .port_pre_bridge_flags and .port_bridge_flags dsa ops to
enable learning for bridge that request it and tweak
.port_stp_state_set to correctly disable learning when port is
configured in standalone mode.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230730074113.21889-2-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There is no need to spam the kernel log with such an indication, remove
this message.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230728183945.760531-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Replace uses of i40e_status to as equivalent as possible error codes.
Remove enum i40e_status as it is no longer needed
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230728171336.2446156-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The two mbox-related mutexes are destroyed in octep_ctrl_mbox_uninit(),
but the corresponding mutex_init calls were missing.
A "DEBUG_LOCKS_WARN_ON(lock->magic != lock)" warning was emitted with
CONFIG_DEBUG_MUTEXES on.
Initialize the two mutexes in octep_ctrl_mbox_init().
Fixes: 577f0d1b1c5f ("octeon_ep: add separate mailbox command and response queues")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230729151516.24153-1-mschmidt@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Similarly to other recently fixed drivers make sure we don't
try to access XDP or page pool APIs when NAPI budget is 0.
NAPI budget of 0 may mean that we are in netpoll.
This may result in running software IRQs in hard IRQ context,
leading to deadlocks or crashes.
To make sure bnapi->tx_pkts don't get wiped without handling
the events, move clearing the field into the handler itself.
Remember to clear tx_pkts after reset (bnxt_enable_napi())
as it's technically possible that netpoll will accumulate
some tx_pkts and then a reset will happen, leaving tx_pkts
out of sync with reality.
Fixes: 322b87ca55f2 ("bnxt_en: add page_pool support")
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20230728205020.2784844-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
