| Age | Commit message (Collapse) | Author |
|---|
|
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should not be manipulaging the DMA_CTRL registers directly by writing
0 to them to disable DMA. This is an operation that needs to be timed to
make sure the DMA engines have been properly stopped since their state
machine stops on a packet boundary, not immediately.
Make sure that tha bcmgenet_fini_dma() calls bcmgenet_dma_teardown() to
ensure a proper DMA engine state. As a result, we need to reorder the
function bodies to resolve the use dependency.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The GENET driver supports SKB fragments, and succeeds in transmitting
them properly, but when reclaiming these transmitted fragments, we will
only update the count of free buffer descriptors by 1, even for SKBs
with fragments. This leads to the networking stack thinking it has more
room than the hardware has when pushing new SKBs, and backing off
consequently because we return NETDEV_TX_BUSY.
Fix this by accounting for the SKB nr_frags plus one (itself) and update
ring->free_bds accordingly with that value for each iteration loop in
__bcmgenet_tx_reclaim().
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In one error condition dm9000_parse_dt() returns NULL, however the
return value is checked using IS_ERR() in dm9000_probe(), leading to the
error not being properly propagated if CONFIG_OF is not enabled or the
device tree data is not available. Fix this by also returning an
ERR_PTR() in this case.
Fixes: 0b8bf1baabe5 (net: dm9000: Allow instantiation using device tree)
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the slave is the curr_active_slave, no need to check
whether the slave is active or not, it is always active.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is an extra semi-colon so __rtl8169_set_features() is called every
time.
Fixes: 929a031dfd62 ('r8169: adjust __rtl8169_set_features')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Hayes Wang <hayeswang@realtek.com>--
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes alignment whereever it doesn't match the open parenthesis
alignment.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes multiple assignments on a single line as warned
by checkpatch.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes unnecessary spaces after typecasts as per checkpatch warnings.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes checkpatch warnings about blank lines after an open brace '{'.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch inserts a blank line after function/struct/union/enum definitions
as per checkpatch warnings.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes multiple blank lines in the driver as per checkpatch
warnings.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes checkpatch warnings in be2net by adding a blank line
between declaration and code blocks.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds speed reporting via ethtool for 20G KR2 interface on the
Skyhawk-R chip.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds speed reporting via ethtool for 40Gbps KR4 interface
on the Skyhawk-R chip.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a sprase warnings regarding endian declarations introduced
by the following commit:
fixes: e36edd9 ("be2net: add ethtool "-m" option support")
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a sparse warning about missing static declaration that was
introduced by the following commit:
fixes: 936767039cdf ("be2net: send a max of 8 EQs to be_cmd_modify_eqd() on Lancer")
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the hw is in ALDPS mode, the hw may have no response for accessing
the most registers. Therefore, the ALDPS should be disabled before
accessing the hw in rtl_ops.init(), rtl_ops.disable(), rtl_ops.up(),
and rtl_ops.down(). Regardless of rtl_ops.enable(), because the hw
wouldn't enter ALDPS mode when linking on. The hw would enter the
ALDPS mode after several seconds when link down occurs and the ALDPS
is enabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There have extra identation before .skb_copy_to_linear_data_offset(),
this patch just remove the identation.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order for Wake-on-LAN to work properly, we query the parent network
device Wake-on-LAN features and advertise those. Similarly, when
configuring Wake-on-LAN on a per-port network interface, we make sure
that we do not accept something the master network devices does not
support.
Finally, we need to maintain a bitmask of the ports enabled for
Wake-on-LAN to prevent the suspend() callback from disabling a port that
is used for waking up the system.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the suspend/resume callbacks for the Broadcom Starfighter 2
switch driver. Suspending the switch requires masking interrupts and
shutting down ports. Resuming the switch requires a software reset since
we do not know which power-sate we might be coming from, and re-enabling
the physical ports that are used.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the below warning message:
qlge_main.c:1754: warning: 'lbq_desc' may be used uninitialized in this function
Signed-off-by: Harish Patil <harish.patil@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Resolves compile warning about use of a deprecated function call:
drivers/net/ethernet/amd/nmclan_cs.c: In function ‘nmclan_config’:
drivers/net/ethernet/amd/nmclan_cs.c:624:3: warning: ‘pcmcia_request_exclusive_irq’ is deprecated (declared at include/pcmcia/ds.h:213) [-Wdeprecated-declarations]
ret = pcmcia_request_exclusive_irq(link, mace_interrupt);
Updates pcmcia_request_exclusive_irq() to pcmcia_request_irq().
CC: Roger Pao <rpao@paonet.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TG3 appears to have an issue performing TSO and checksum offloading
correclty when the frame has been vlan encapsulated (non-accelrated).
In these cases, tcp checksum is not correctly updated.
This patch attempts to work around this issue. After the patch,
802.1ad vlans start working correctly over tg3 devices.
CC: Prashant Sreedharan <prashant@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 412ca1550cbe ("macvlan: Move broadcasts into a work queue"), the
driver uses tx_queue_len of the master device as the limit of packets enqueuing.
Problem is that virtual drivers have this value set to 0, thus all broadcast
packets were rejected.
Because tx_queue_len was arbitrarily chosen, I replace it with a static limit
of 1000 (also arbitrarily chosen).
CC: Herbert Xu <herbert@gondor.apana.org.au>
Reported-by: Thibaut Collet <thibaut.collet@6wind.com>
Suggested-by: Thibaut Collet <thibaut.collet@6wind.com>
Tested-by: Thibaut Collet <thibaut.collet@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes the following randconfig build failure:
> drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c: In function
> ‘pch_ptp_match’:
> drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c:130:2: error:
> implicit declaration of function ‘ptp_classify_raw’
> [-Werror=implicit-function-declaration]
> if (ptp_classify_raw(skb) == PTP_CLASS_NONE)
> ^
> cc1: some warnings being treated as errors
> make[5]: *** [drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.o] Error 1
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-09-18
This series contains updates to ixgbe and ixgbevf.
Ethan Zhao cleans up ixgbe and ixgbevf by removing bd_number from the
adapter struct because it is not longer useful.
Mark fixes ixgbe where if a hardware transmit timestamp is requested,
an uninitialized workqueue entry may be scheduled. Added a check for
a PTP clock to avoid that.
Jacob provides a number of cleanups for ixgbe. Since we may call
ixgbe_acquire_msix_vectors() prior to registering our netdevice, we
should not use the netdevice specific printk and use e_dev_warn()
instead. Similar to how ixgbevf handles acquiring MSI-X vectors, we
can return an error code instead of relying on the flag being set.
This makes it more clear that we have failed to setup MSI-X mode and
will make it easier to consolidate MSI-X related code into a single
function. In the case of disabling DCB, it is not an error since we
still can function, we just have to let the user know. So use
e_dev_warn() instead of e_err(). Added warnings for other features
that are disabled when we are without MSI-X support. Cleanup flags
that are no longer used or needed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://gitorious.org/linux-can/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2014-09-18
this is a pull request of 8 patches for current net.
A patch by Roger Quadros for the c_can driver fixes the swapped parameters of
the c_can_hw_raminit_ti() function. Oliver Hartkopp adds the missing PCI ids to
the peak_pci driver to support the single channel PCAN ExpressCard 34 adapter.
David Dueck converts the at91_can driver to use proper clock handling
functions. Then there are 5 patches by David Jander and me which fix several
mailbox related problems in the flexcan driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function derives the base address of the CQE from the CQE size,
and calculates the real CQE context segment in it from the factor
(this is like before). Before this change the code used the factor to
calculate the base address of the CQE as well.
The factor indicates in which segment of the cqe stride the cqe information
is located. For 32-byte strides, the segment is 0, and for 64 byte strides,
the segment is 1 (bytes 32..63). Using the factor was ok as long as we had
only 32 and 64 byte strides. However, with larger strides, the factor is zero,
and so cannot be used to calculate the base of the CQE.
The helper uses the same method of CQE buffer pulling made by all other
components that reads the CQE buffer (mlx4_ib driver and libmlx4).
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable mlx4 interrupt handler to work with EQE stride feature,
The feature may be enabled when cache line is bigger than 64B.
The EQE size will then be the cache line size, and the context
segment resides in [0-31] offset.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This feature is intended for archs having cache line larger then 64B.
Since our CQE/EQEs are generally 64B in those systems, HW will write
twice to the same cache line consecutively, causing pipe locks due to
he hazard prevention mechanism. For elements in a cyclic buffer, writes
are consecutive, so entries smaller than a cache line should be
avoided, especially if they are written at a high rate.
Reduce consecutive writes to same cache line in CQs/EQs, by allowing the
driver to increase the distance between entries so that each will reside
in a different cache line. Until the introduction of this feature, there
were two types of CQE/EQE:
1. 32B stride and context in the [0-31] segment
2. 64B stride and context in the [32-63] segment
This feature introduces two additional types:
3. 128B stride and context in the [0-31] segment (128B cache line)
4. 256B stride and context in the [0-31] segment (256B cache line)
Modify the mlx4_core driver to query the device for the CQE/EQE cache
line stride capability and to enable that capability when the host
cache line size is larger than 64 bytes (supported cache lines are
128B and 256B).
The mlx4 IB driver and libmlx4 need not be aware of this change. The PF
context behaviour is changed to require this change in VF drivers
running on such archs.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I cannot move a macvlan interface created on top of a bonding interface
to a different namespace:
% ip netns add dummy0
% ip link add link bond0 mac0 type macvlan
% ip link set mac0 netns dummy0
RTNETLINK answers: Invalid argument
%
The problem seems to be that commit f9399814927a ("bonding: Don't allow
bond devices to change network namespaces.") sets NETIF_F_NETNS_LOCAL
on bonding interfaces, and commit 797f87f83b60 ("macvlan: fix netdev
feature propagation from lower device") causes macvlan interfaces
to inherit its features from the lower device.
NETIF_F_NETNS_LOCAL should not be inherited from the lower device
by a macvlan.
Patch tested on 3.16.
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
pull request: wireless 2014-09-17
Please pull this batch of fixes intended for the 3.17 stream...
Arend van Spriel sends a trio of minor brcmfmac fixes, including a
fix for a Kconfig/build issue, a fix for a crash (null reference),
and a regression fix related to event handling on a P2P interface.
Hante Meuleman follows-up with a brcmfmac fix for a memory leak.
Johannes Stezenbach brings an ath9k_htc fix for a regression related
to hardware decryption offload.
Marcel Holtmann delivers a one-liner to properly mark a device ID
table in rfkill-gpio.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using new Multi-function modes it's possible that due to incompatible
configuration management FW will fallback into an existing mode.
Notice that at the moment this fallback is exactly the same as the already
existing switch-independent multi-function mode, but we still use existing
infrastructure to hold this information [in case some small differences will
arise in the future].
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for a new multi-function mode based on the Unified Fabric Port
system specifications.
Support includes configuration of:
1. Outer vlan tags.
2. Bandwidth settings.
3. Virtual link enable/disable.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rearrange macros to query for storage-only modes in different MF environment.
Improves the readibility and maintainability of the code. E.g.:
- if (IS_MF_STORAGE_SD(bp) || IS_MF_FCOE_AFEX(bp))
+ if (IS_MF_STORAGE_ONLY(bp))
In addition, this removes the need for bnx2x_is_valid_ether_addr().
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recently aded the use of skb_frag_dma_map to 3c59x, but didn't realize it
automatically included the frag_offset internally, as well as provided an option
to specify an extra offset in the parameter list. We need to specify an offset
of 0 in the parameter list to avoid skb corruption that results in lost
connections.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Linux Kernel list <linux-kernel@vger.kernel.org>
CC: "David S. Miller" <davem@davemloft.net>
CC: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
|
|
Noted that 3c59x has no checks on transmit for failed DMA mappings, and no
ability to unmap fragments when a single map fails in the middle of a transmit.
This patch provides error checking to ensure that dma mappings work properly,
and unrolls an skb mapping if a fragmented skb transmission has a mapping
failure to prevent leaks.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Linux Kernel list <linux-kernel@vger.kernel.org>
CC: "David S. Miller" <davem@davemloft.net>
CC: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
|
|
Now that the GENET and SF2 drivers have been updated to communicate us
what is the revision of the BCM7xxx integrated PHY, utilize that
information in the config_init() callback to call into the appropriate
workaround function based on our revision.
While at it, we also print the revision and patch level to help debug
new chips.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The integrated BCM7xxx PHY contains no useful revision information
in its MII_PHYSID2 bits 3:0, that information is instead contained in
the SWITCH_REG_PHY_REVISION register.
Read this register, store its value, and return it by implementing the
dsa_switch::get_phy_flags() callback accordingly. The register layout is
already matching what the BCM7xxx PHY driver is expecting to find.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The integrated BCM7xxx PHY contains no useful revision information in
its MII_PHYSID2 bits 3:0, that information is instead contained in the
GENET hardware block.
We already read the GENET 32-bit revision register, so store the
integrated PHY revision in the driver private structure, and then
communicate this revision value to the PHY driver by overriding the
phy_flags value.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have removed the need for the PHY_BRCM_100MBPS_WAR flag, we
can remove it from the GENET driver and the broadcom shared header file.
The PHY driver checks the PHY supported bitmask instead.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need for the PHY driver to check PHY_BRCM_100MBPS_WAR since
that is redundant with checking the PHY device supported features. Get
rid of that workaround flag.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify vxlan implementation using common UDP tunnel APIs.
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When enable three queues on imx6sx enet, and then do tx performance
test with iperf tool, after some time running, tx hang.
Found that:
If uDMA is running, software set TDAR may cause tx hang.
If uDMA is in idle, software set TDAR don't cause tx hang.
There is a TDAR race condition for mutliQ when the software sets TDAR
and the UDMA clears TDAR simultaneously or in a small window (2-4 cycles).
This will cause the udma_tx and udma_tx_arbiter state machines to hang.
The issue exist at i.MX6SX enet IP.
So, the Workaround is checking TDAR status four time, if TDAR cleared by
hardware and then write TDAR, otherwise don't set TDAR.
The patch is only one Workaround for the issue ERR007885.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when enable interrupt coalesce, 8 BD is not enough.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
i.MX6 SX support interrupt coalescence feature
By default, init the interrupt coalescing frame count threshold and
timer threshold.
Supply the ethtool interfaces as below for user tuning to improve
enet performance:
rx_max_coalesced_frames
rx_coalesce_usecs
tx_max_coalesced_frames
tx_coalesce_usecs
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
check tx and rx queue seperately.
fix typo, "Invalidate" and "fail".
change pr_err to pr_warn.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
