| Age | Commit message (Collapse) | Author |
|---|
|
As noted in commit 28c2d1a7a0bf ("net: bcmgenet: enable loopback
during UniMAC sw_reset") the UniMAC must be clocked at least 5
cycles while the sw_reset is asserted to ensure a clean reset.
That commit enabled local loopback to provide an Rx clock from the
GENET sourced Tx clk. However, when connected in MII mode the Tx
clk is sourced by the PHY so if an EPHY is not supplying clocks
(e.g. when the link is down) the UniMAC does not receive the
necessary clocks.
This commit extends the sw_reset window until the PHY reports that
the link is up thereby ensuring that the clocks are being provided
to the MAC to produce a clean reset.
One consequence is that if the system attempts to enter a Wake on
LAN suspend state when the PHY link has not been active the MAC
may not have had a chance to initialize cleanly. In this case, we
remove the sw_reset and enable the WoL reception path as normal
with the hope that the PHY will provide the necessary clocks to
drive the WoL blocks if the link becomes active after the system
has entered suspend.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 3a55402c93877d291b0a612d25edb03d1b4b93ac.
This is not a good solution when connecting to an external switch
that may not support the isolation of the TXC signal resulting in
output driver contention on the pin.
A different solution is necessary.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Per the dt-binding the interrupt is optional so use
platform_get_irq_optional() instead of platform_get_irq(). Since
commit 7723f4c5ecdb ("driver core: platform: Add an error message to
platform_get_irq*()") platform_get_irq() produces an error message
orion-mdio f1072004.mdio: IRQ index 0 not found
which is perfectly normal if one hasn't specified the optional property
in the device tree.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit e1f550dc44a4d535da4e25ada1b0eaf8f3417929.
platform_get_irq_optional() will still return -ENXIO when no interrupt
is provided so the additional error handling caused the driver prone to
fail when no interrupt was specified. Revert the change so we can apply
the correct minimal fix.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the case where the last mvneta_poll did not process all
RX packets, we need to xor the pp->cause_rx_tx or port->cause_rx_tx
before claculating the rx_queue.
Fixes: 2dcf75e2793c ("net: mvneta: Associate RX queues with each CPU")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
printk in macro vxge_debug_ll uses __VA_ARGS__ without "##" prefix,
it causes a build error when there is no variable
arguments(e.g. only fmt is specified.).
Signed-off-by: Zheng Wei <wei.zheng@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Treat all internal delay variants the same as RGMII.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: "David S . Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: "David S . Miller" <davem@davemloft.net>
Cc: Edward Cree <ecree@solarflare.com>
Cc: Martin Habets <mhabets@solarflare.com>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Cc: "David S . Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: oss-drivers@netronome.com
Cc: netdev@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Cc: "David S . Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: oss-drivers@netronome.com
To: netdev@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: "David S . Miller" <davem@davemloft.net>
Cc: Tariq Toukan <tariqt@mellanox.com>
To: netdev@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: "David S . Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cited commit set a value of 2^31-1 in order to "disable" the shaper
on a given a port. However, the length of the maximum shaper rate field
was not updated from 28 bits to 31 bits, which means ports are still
limited to ~268Gbps despite supporting speeds of 400Gbps.
Fix this by increasing the field's length.
Fixes: 92afbfedb77d ("mlxsw: reg: Increase MLXSW_REG_QEEC_MAS_DIS")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The debug check must be done after unregister_netdevice_many() call --
the list_del() for this is done inside .ndo_stop.
Fixes: 2843a25348f8 ("geneve: speedup geneve tunnels dismantle")
Reported-and-tested-by: <syzbot+68a8ed58e3d17c700de5@syzkaller.appspotmail.com>
Cc: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the hardware TID index is assumed to start from index 0.
However, with the following changeset,
commit c21939998802 ("cxgb4: add support for high priority filters")
hardware TID index can start after the high priority region, which
has introduced a regression resulting in remove filters entry
failure for cxgb4 unload path. This patch fix that.
Fixes: c21939998802 ("cxgb4: add support for high priority filters")
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not every stmmac based platform makes use of the eth_wake_irq or eth_lpi
interrupts. Use the platform_get_irq_byname_optional variant for these
interrupts, so no error message is displayed, if they can't be found.
Rather print an information to hint something might be wrong to assist
debugging on platforms which use these interrupts.
Signed-off-by: Markus Fuchs <mklntf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.6
Third, and hopefully last, set of fixes for v5.6.
iwlwifi
* fix a locking issue in time events handling
* a fix in rate-scaling
* fix for a potential NULL pointer deref
* enable antenna diversity in some devices that were erroneously not doing it
* allow FW dumps to continue when the FW is stuck
* a fix in the HE capabilities handling
* another fix for FW dumps where we were reading wrong addresses
* fix link in MAINTAINERS file
rtlwifi
* fix regression causing connect issues in v5.4
wlcore
* remove merge damage which luckily didn't have any impact on functionality
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the bounds check on index is off by one and can lead to
an out of bounds access on array priv->filters_loc when index is
RXCHK_BRCM_TAG_MAX.
Fixes: bb9051a2b230 ("net: systemport: Add support for WAKE_FILTER")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So far we have the unfortunate situation that mdio_bus_phy_may_suspend()
is called in suspend AND resume path, assuming that function result is
the same. After the original change this is no longer the case,
resulting in broken resume as reported by Geert.
To fix this call mdio_bus_phy_may_suspend() in the suspend path only,
and let the phy_device store the info whether it was suspended by
MDIO bus PM.
Fixes: 503ba7c69610 ("net: phy: Avoid multiple suspends")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, PF missed to clear the port base VLAN for VF when
unload. In this case, the VLAN id will remain in the VLAN
table. This patch fixes it.
Fixes: 92f11ea177cd ("net: hns3: fix set port based VLAN issue for VF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the user manual, the ingress and egress VLAN filter
are configured at the same time. Currently, hclge_init_vlan_config()
and hclge_set_vlan_spoofchk() will both change the VLAN filter
switch. So it's necessary to read the old configuration before
modifying it.
Fixes: 22044f95faa0 ("net: hns3: add support for spoof check setting")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, if VF is loaded on the host side, the host doesn't
clear the VF's VLAN table entries when VF removing. In this
case, when doing reset and disabling sriov at the same time the
VLAN device over VF will be removed, but the VLAN table entries
in hardware are remained.
This patch fixes it by asking PF to clear the VLAN table entries for
VF when VF is removing. It also clears the VLAN table full bit
after VF VLAN table entries being cleared.
Fixes: c6075b193462 ("net: hns3: Record VF vlan tables")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The HNS3 driver supports to configure TC numbers and TC to priority
map via "tc" tool. But when delete the rule, will fail, because
the HNS3 driver needs at least one TC, but the "tc" tool sets TC
number to zero when delete.
This patch makes sure that the TC number is at least one.
Fixes: 30d240dfa2e8 ("net: hns3: Add mqprio hardware offload support in hns3 driver")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit mentioned below added a stray plus sign, likely
due to some conflict resolution (i.e. as a leftover from a
unified diff), which was harmless since it was just used as
an integer constant modifier. Remove it anyway, now that I
stumbled across it.
Fixes: cf33a7728bf2 ("wlcore: mesh: Add support for RX Broadcast Key")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
For some unexplained reason, commit d1d1a96bdb44 ("rtlwifi: rtl8188ee:
Remove local configuration variable") broke at least one system. As
the only net effect of the change was to remove 2 bytes from the start
of struct phy_status_rpt, this patch adds 2 bytes of padding at the
beginning of the struct.
Fixes: d1d1a96bdb44 ("rtlwifi: rtl8188ee: Remove local configuration variable")
Cc: Stable <stable@vger.kernel.org> # V5.4+
Reported-by: Ashish <ashishkumar.yadav@students.iiserpune.ac.in>
Tested-by: Ashish <ashishkumar.yadav@students.iiserpune.ac.in>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Per the dt-binding the interrupt is optional so use
platform_get_irq_optional() instead of platform_get_irq(). Since
commit 7723f4c5ecdb ("driver core: platform: Add an error message to
platform_get_irq*()") platform_get_irq() produces an error message
orion-mdio f1072004.mdio: IRQ index 0 not found
which is perfectly normal if one hasn't specified the optional property
in the device tree.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only the bottom 12 bits contain the ATU bin occupancy statistics. The
upper bits need masking off.
Fixes: e0c69ca7dfbb ("net: dsa: mv88e6xxx: Add ATU occupancy via devlink resources")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes an off-by-one error in strncpy size argument in
drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c. The issue is that in:
strncmp(opt, "eee_timer:", 6)
the passed string literal: "eee_timer:" has 10 bytes (without the NULL
byte) and the passed size argument is 6. As a result, the logic will
also accept other, malformed strings, e.g. "eee_tiXXX:".
This bug doesn't seem to have any security impact since its present in
module's cmdline parsing code.
Signed-off-by: Dominik Czarnota <dominik.b.czarnota@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fec_enet_set_coalesce() validates the previously set params
and if they are within range proceeds to apply the new ones.
The new ones, however, are not validated. This seems backwards,
probably a copy-paste error?
Compile tested only.
Fixes: d851b47b22fc ("net: fec: add interrupt coalescence feature support")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clang warns:
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:2860:9: warning:
converting the result of '?:' with integer constants to a boolean always
evaluates to 'true' [-Wtautological-constant-compare]
return DPAA_FD_DATA_ALIGNMENT ? ALIGN(headroom,
^
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:131:34: note: expanded
from macro 'DPAA_FD_DATA_ALIGNMENT'
\#define DPAA_FD_DATA_ALIGNMENT (fman_has_errata_a050385() ? 64 : 16)
^
1 warning generated.
This was exposed by commit 3c68b8fffb48 ("dpaa_eth: FMan erratum A050385
workaround") even though it appears to have been an issue since the
introductory commit 9ad1a3749333 ("dpaa_eth: add support for DPAA
Ethernet") since DPAA_FD_DATA_ALIGNMENT has never been able to be zero.
Just replace the whole boolean expression with the true branch, as it is
always been true.
Link: https://github.com/ClangBuiltLinux/linux/issues/928
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Notify the offload engine about MAC address change to reconfigure it
accordingly.
Fixes: 3cf3227a21d1 ("net: macsec: hardware offloading infrastructure")
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SCI should be updated, because it contains MAC in its first 6 octets.
Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ibmvnic driver does not check the device state when the device
is removed. If the device is removed while a device reset is being
processed, the remove may free structures needed by the reset,
causing an oops.
Fix this by checking the device state before processing device remove.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
First batch of fixes intended for v5.6
* Fix a locking issue in time events handling;
* A fix in rate-scaling;
* Fix for a potential NULL pointer deref;
* Enable antenna diversity in some devices that were erroneously not
doing it;
* Allow FW dumps to continue when the FW is stuck;
* A fix in the HE capabilities handling;
* Another fix for FW dumps where we were reading wrong addresses.
|
|
What the driver writes into MAC_MAXLEN_CFG does not actually represent
VLAN_ETH_FRAME_LEN but instead ETH_FRAME_LEN + ETH_FCS_LEN. Yes they are
numerically equal, but the difference is important, as the switch treats
VLAN-tagged traffic specially and knows to increase the maximum accepted
frame size automatically. So it is always wrong to account for VLAN in
the MAC_MAXLEN_CFG register.
Unconditionally increase the maximum allowed frame size for
double-tagged traffic. Accounting for the additional length does not
mean that the other VLAN membership checks aren't performed, so there's
no harm done.
Also, stop abusing the MTU name for configuring the MRU. There is no
support for configuring the MRU on an interface at the moment.
Fixes: a556c76adc05 ("net: mscc: Add initial Ocelot switch support")
Fixes: fa914e9c4d94 ("net: mscc: ocelot: create a helper for changing the port MTU")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit e18b353f102e ("ipvlan: add cond_resched_rcu() while
processing muticast backlog") added a cond_resched_rcu() in a loop
using rcu protection to iterate over slaves.
This is breaking rcu rules, so lets instead use cond_resched()
at a point we can reschedule
Fixes: e18b353f102e ("ipvlan: add cond_resched_rcu() while processing muticast backlog")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Rx bound multicast packets are deferred to a workqueue and
macvlan can also suffer from the same attack that was discovered
by Syzbot for IPvlan. This solution is not as effective as in
IPvlan. IPvlan defers all (Tx and Rx) multicast packet processing
to a workqueue while macvlan does this way only for the Rx. This
fix should address the Rx codition to certain extent.
Tx is still suseptible. Tx multicast processing happens when
.ndo_start_xmit is called, hence we cannot add cond_resched().
However, it's not that severe since the user which is generating
/ flooding will be affected the most.
Fixes: 412ca1550cbe ("macvlan: Move broadcasts into a work queue")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If there are substantial number of slaves created as simulated by
Syzbot, the backlog processing could take much longer and result
into the issue found in the Syzbot report.
INFO: rcu_sched detected stalls on CPUs/tasks:
(detected by 1, t=10502 jiffies, g=5049, c=5048, q=752)
All QSes seen, last rcu_sched kthread activity 10502 (4294965563-4294955061), jiffies_till_next_fqs=1, root ->qsmask 0x0
syz-executor.1 R running task on cpu 1 10984 11210 3866 0x30020008 179034491270
Call Trace:
<IRQ>
[<ffffffff81497163>] _sched_show_task kernel/sched/core.c:8063 [inline]
[<ffffffff81497163>] _sched_show_task.cold+0x2fd/0x392 kernel/sched/core.c:8030
[<ffffffff8146a91b>] sched_show_task+0xb/0x10 kernel/sched/core.c:8073
[<ffffffff815c931b>] print_other_cpu_stall kernel/rcu/tree.c:1577 [inline]
[<ffffffff815c931b>] check_cpu_stall kernel/rcu/tree.c:1695 [inline]
[<ffffffff815c931b>] __rcu_pending kernel/rcu/tree.c:3478 [inline]
[<ffffffff815c931b>] rcu_pending kernel/rcu/tree.c:3540 [inline]
[<ffffffff815c931b>] rcu_check_callbacks.cold+0xbb4/0xc29 kernel/rcu/tree.c:2876
[<ffffffff815e3962>] update_process_times+0x32/0x80 kernel/time/timer.c:1635
[<ffffffff816164f0>] tick_sched_handle+0xa0/0x180 kernel/time/tick-sched.c:161
[<ffffffff81616ae4>] tick_sched_timer+0x44/0x130 kernel/time/tick-sched.c:1193
[<ffffffff815e75f7>] __run_hrtimer kernel/time/hrtimer.c:1393 [inline]
[<ffffffff815e75f7>] __hrtimer_run_queues+0x307/0xd90 kernel/time/hrtimer.c:1455
[<ffffffff815e90ea>] hrtimer_interrupt+0x2ea/0x730 kernel/time/hrtimer.c:1513
[<ffffffff844050f4>] local_apic_timer_interrupt arch/x86/kernel/apic/apic.c:1031 [inline]
[<ffffffff844050f4>] smp_apic_timer_interrupt+0x144/0x5e0 arch/x86/kernel/apic/apic.c:1056
[<ffffffff84401cbe>] apic_timer_interrupt+0x8e/0xa0 arch/x86/entry/entry_64.S:778
RIP: 0010:do_raw_read_lock+0x22/0x80 kernel/locking/spinlock_debug.c:153
RSP: 0018:ffff8801dad07ab8 EFLAGS: 00000a02 ORIG_RAX: ffffffffffffff12
RAX: 0000000000000000 RBX: ffff8801c4135680 RCX: 0000000000000000
RDX: 1ffff10038826afe RSI: ffff88019d816bb8 RDI: ffff8801c41357f0
RBP: ffff8801dad07ac0 R08: 0000000000004b15 R09: 0000000000310273
R10: ffff88019d816bb8 R11: 0000000000000001 R12: ffff8801c41357e8
R13: 0000000000000000 R14: ffff8801cfb19850 R15: ffff8801cfb198b0
[<ffffffff8101460e>] __raw_read_lock_bh include/linux/rwlock_api_smp.h:177 [inline]
[<ffffffff8101460e>] _raw_read_lock_bh+0x3e/0x50 kernel/locking/spinlock.c:240
[<ffffffff840d78ca>] ipv6_chk_mcast_addr+0x11a/0x6f0 net/ipv6/mcast.c:1006
[<ffffffff84023439>] ip6_mc_input+0x319/0x8e0 net/ipv6/ip6_input.c:482
[<ffffffff840211c8>] dst_input include/net/dst.h:449 [inline]
[<ffffffff840211c8>] ip6_rcv_finish+0x408/0x610 net/ipv6/ip6_input.c:78
[<ffffffff840214de>] NF_HOOK include/linux/netfilter.h:292 [inline]
[<ffffffff840214de>] NF_HOOK include/linux/netfilter.h:286 [inline]
[<ffffffff840214de>] ipv6_rcv+0x10e/0x420 net/ipv6/ip6_input.c:278
[<ffffffff83a29efa>] __netif_receive_skb_one_core+0x12a/0x1f0 net/core/dev.c:5303
[<ffffffff83a2a15c>] __netif_receive_skb+0x2c/0x1b0 net/core/dev.c:5417
[<ffffffff83a2f536>] process_backlog+0x216/0x6c0 net/core/dev.c:6243
[<ffffffff83a30d1b>] napi_poll net/core/dev.c:6680 [inline]
[<ffffffff83a30d1b>] net_rx_action+0x47b/0xfb0 net/core/dev.c:6748
[<ffffffff846002c8>] __do_softirq+0x2c8/0x99a kernel/softirq.c:317
[<ffffffff813e656a>] invoke_softirq kernel/softirq.c:399 [inline]
[<ffffffff813e656a>] irq_exit+0x16a/0x1a0 kernel/softirq.c:439
[<ffffffff84405115>] exiting_irq arch/x86/include/asm/apic.h:561 [inline]
[<ffffffff84405115>] smp_apic_timer_interrupt+0x165/0x5e0 arch/x86/kernel/apic/apic.c:1058
[<ffffffff84401cbe>] apic_timer_interrupt+0x8e/0xa0 arch/x86/entry/entry_64.S:778
</IRQ>
RIP: 0010:__sanitizer_cov_trace_pc+0x26/0x50 kernel/kcov.c:102
RSP: 0018:ffff880196033bd8 EFLAGS: 00000246 ORIG_RAX: ffffffffffffff12
RAX: ffff88019d8161c0 RBX: 00000000ffffffff RCX: ffffc90003501000
RDX: 0000000000000002 RSI: ffffffff816236d1 RDI: 0000000000000005
RBP: ffff880196033bd8 R08: ffff88019d8161c0 R09: 0000000000000000
R10: 1ffff10032c067f0 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000080 R14: 0000000000000000 R15: 0000000000000000
[<ffffffff816236d1>] do_futex+0x151/0x1d50 kernel/futex.c:3548
[<ffffffff816260f0>] C_SYSC_futex kernel/futex_compat.c:201 [inline]
[<ffffffff816260f0>] compat_SyS_futex+0x270/0x3b0 kernel/futex_compat.c:175
[<ffffffff8101da17>] do_syscall_32_irqs_on arch/x86/entry/common.c:353 [inline]
[<ffffffff8101da17>] do_fast_syscall_32+0x357/0xe1c arch/x86/entry/common.c:415
[<ffffffff84401a9b>] entry_SYSENTER_compat+0x8b/0x9d arch/x86/entry/entry_64_compat.S:139
RIP: 0023:0xf7f23c69
RSP: 002b:00000000f5d1f12c EFLAGS: 00000282 ORIG_RAX: 00000000000000f0
RAX: ffffffffffffffda RBX: 000000000816af88 RCX: 0000000000000080
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 000000000816af8c
RBP: 00000000f5d1f228 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
rcu_sched kthread starved for 10502 jiffies! g5049 c5048 f0x2 RCU_GP_WAIT_FQS(3) ->state=0x0 ->cpu=1
rcu_sched R running task on cpu 1 13048 8 2 0x90000000 179099587640
Call Trace:
[<ffffffff8147321f>] context_switch+0x60f/0xa60 kernel/sched/core.c:3209
[<ffffffff8100095a>] __schedule+0x5aa/0x1da0 kernel/sched/core.c:3934
[<ffffffff810021df>] schedule+0x8f/0x1b0 kernel/sched/core.c:4011
[<ffffffff8101116d>] schedule_timeout+0x50d/0xee0 kernel/time/timer.c:1803
[<ffffffff815c13f1>] rcu_gp_kthread+0xda1/0x3b50 kernel/rcu/tree.c:2327
[<ffffffff8144b318>] kthread+0x348/0x420 kernel/kthread.c:246
[<ffffffff84400266>] ret_from_fork+0x56/0x70 arch/x86/entry/entry_64.S:393
Fixes: ba35f8588f47 (“ipvlan: Defer multicast / broadcast processing to a work-queue”)
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPvlan in L3 mode discards outbound multicast packets but performs
the check before ensuring the ether-header is set or not. This is
an error that Eric found through code browsing.
Fixes: 2ad7bf363841 (“ipvlan: Initial check-in of the IPVLAN driver.”)
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's a resource, not a parameter, so we can't copy it into the new
channel's TX queues, otherwise aliasing will lead to resource-
management bugs if the channel is subsequently torn down without
being initialised.
Before the Fixes:-tagged commit there was a similar bug with
tsoh_page, but I'm not sure it's worth doing another fix for such
old kernels.
Fixes: e9117e5099ea ("sfc: Firmware-Assisted TSO version 2")
Suggested-by: Derek Shute <Derek.Shute@stratus.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ACS (auto PAD/FCS stripping) removes FCS off 802.3 packets (LLC) so that
there is no need to manually strip it for such packets. The enhanced DMA
descriptors allow to flag LLC packets so that the receiving callback can
use that to strip FCS manually or not. On the other hand, normal
descriptors do not support that.
Thus in order to not truncate LLC packet ACS should be disabled when
using normal DMA descriptors.
Fixes: 47dd7a540b8a0 ("net: add support for STMicroelectronics Ethernet controllers.")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a problem when ipvlan slaves are created on a master device that
is a vmxnet3 device (ipvlan in VMware guests). The vmxnet3 driver does not
support unicast address filtering. When an ipvlan device is brought up in
ipvlan_open(), the ipvlan driver calls dev_uc_add() to add the hardware
address of the vmxnet3 master device to the unicast address list of the
master device, phy_dev->uc. This inevitably leads to the vmxnet3 master
device being forced into promiscuous mode by __dev_set_rx_mode().
Promiscuous mode is switched on the master despite the fact that there is
still only one hardware address that the master device should use for
filtering in order for the ipvlan device to be able to receive packets.
The comment above struct net_device describes the uc_promisc member as a
"counter, that indicates, that promiscuous mode has been enabled due to
the need to listen to additional unicast addresses in a device that does
not implement ndo_set_rx_mode()". Moreover, the design of ipvlan
guarantees that only the hardware address of a master device,
phy_dev->dev_addr, will be used to transmit and receive all packets from
its ipvlan slaves. Thus, the unicast address list of the master device
should not be modified by ipvlan_open() and ipvlan_stop() in order to make
ipvlan a workable option on masters that do not support unicast address
filtering.
Fixes: 2ad7bf3638411 ("ipvlan: Initial check-in of the IPVLAN driver")
Reported-by: Per Sundstrom <per.sundstrom@redqube.se>
Signed-off-by: Jiri Wiesner <jwiesner@suse.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These are a couple of read locks that should be write locks.
Fixes: fbb39807e9ae ("ionic: support sr-iov operations")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to commit 38f88c454042 ("bonding/alb: properly access headers
in bond_alb_xmit()"), we need to make sure arp header was pulled
in skb->head before blindly accessing it in rlb_arp_xmit().
Remove arp_pkt() private helper, since it is more readable/obvious
to have the following construct back to back :
if (!pskb_network_may_pull(skb, sizeof(*arp)))
return NULL;
arp = (struct arp_pkt *)skb_network_header(skb);
syzbot reported :
BUG: KMSAN: uninit-value in bond_slave_has_mac_rx include/net/bonding.h:704 [inline]
BUG: KMSAN: uninit-value in rlb_arp_xmit drivers/net/bonding/bond_alb.c:662 [inline]
BUG: KMSAN: uninit-value in bond_alb_xmit+0x575/0x25e0 drivers/net/bonding/bond_alb.c:1477
CPU: 0 PID: 12743 Comm: syz-executor.4 Not tainted 5.6.0-rc2-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x220 lib/dump_stack.c:118
kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:118
__msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215
bond_slave_has_mac_rx include/net/bonding.h:704 [inline]
rlb_arp_xmit drivers/net/bonding/bond_alb.c:662 [inline]
bond_alb_xmit+0x575/0x25e0 drivers/net/bonding/bond_alb.c:1477
__bond_start_xmit drivers/net/bonding/bond_main.c:4257 [inline]
bond_start_xmit+0x85d/0x2f70 drivers/net/bonding/bond_main.c:4282
__netdev_start_xmit include/linux/netdevice.h:4524 [inline]
netdev_start_xmit include/linux/netdevice.h:4538 [inline]
xmit_one net/core/dev.c:3470 [inline]
dev_hard_start_xmit+0x531/0xab0 net/core/dev.c:3486
__dev_queue_xmit+0x37de/0x4220 net/core/dev.c:4063
dev_queue_xmit+0x4b/0x60 net/core/dev.c:4096
packet_snd net/packet/af_packet.c:2967 [inline]
packet_sendmsg+0x8347/0x93b0 net/packet/af_packet.c:2992
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg net/socket.c:672 [inline]
__sys_sendto+0xc1b/0xc50 net/socket.c:1998
__do_sys_sendto net/socket.c:2010 [inline]
__se_sys_sendto+0x107/0x130 net/socket.c:2006
__x64_sys_sendto+0x6e/0x90 net/socket.c:2006
do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x45c479
Code: ad b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fc77ffbbc78 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 00007fc77ffbc6d4 RCX: 000000000045c479
RDX: 000000000000000e RSI: 00000000200004c0 RDI: 0000000000000003
RBP: 000000000076bf20 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff
R13: 0000000000000a04 R14: 00000000004cc7b0 R15: 000000000076bf2c
Uninit was created at:
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:144 [inline]
kmsan_internal_poison_shadow+0x66/0xd0 mm/kmsan/kmsan.c:127
kmsan_slab_alloc+0x8a/0xe0 mm/kmsan/kmsan_hooks.c:82
slab_alloc_node mm/slub.c:2793 [inline]
__kmalloc_node_track_caller+0xb40/0x1200 mm/slub.c:4401
__kmalloc_reserve net/core/skbuff.c:142 [inline]
__alloc_skb+0x2fd/0xac0 net/core/skbuff.c:210
alloc_skb include/linux/skbuff.h:1051 [inline]
alloc_skb_with_frags+0x18c/0xa70 net/core/skbuff.c:5766
sock_alloc_send_pskb+0xada/0xc60 net/core/sock.c:2242
packet_alloc_skb net/packet/af_packet.c:2815 [inline]
packet_snd net/packet/af_packet.c:2910 [inline]
packet_sendmsg+0x66a0/0x93b0 net/packet/af_packet.c:2992
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg net/socket.c:672 [inline]
__sys_sendto+0xc1b/0xc50 net/socket.c:1998
__do_sys_sendto net/socket.c:2010 [inline]
__se_sys_sendto+0x107/0x130 net/socket.c:2006
__x64_sys_sendto+0x6e/0x90 net/socket.c:2006
do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Align buffers, data start, SG fragment length to avoid DMA splits.
These changes prevent the A050385 erratum to manifest itself:
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak; thus stopping further packet processing.
The FMAN internal queue can overflow when FMAN splits single
read or write transactions into multiple smaller transactions
such that more than 17 AXI transactions are in flight from FMAN
to interconnect. When the FMAN internal queue overflows, it can
stall further packet processing. The issue can occur with any one
of the following three conditions:
1. FMAN AXI transaction crosses 4K address boundary (Errata
A010022)
2. FMAN DMA address for an AXI transaction is not 16 byte
aligned, i.e. the last 4 bits of an address are non-zero
3. Scatter Gather (SG) frames have more than one SG buffer in
the SG list and any one of the buffers, except the last
buffer in the SG list has data size that is not a multiple
of 16 bytes, i.e., other than 16, 32, 48, 64, etc.
With any one of the above three conditions present, there is
likelihood of stalled FMAN packet processing, especially under
stress with multiple ports injecting line-rate traffic.
To avoid situations that stall FMAN packet processing, all of the
above three conditions must be avoided; therefore, configure the
system with the following rules:
1. Frame buffers must not span a 4KB address boundary, unless
the frame start address is 256 byte aligned
2. All FMAN DMA start addresses (for example, BMAN buffer
address, FD[address] + FD[offset]) are 16B aligned
3. SG table and buffer addresses are 16B aligned and the size
of SG buffers are multiple of 16 bytes, except for the last
SG buffer that can be of any size.
Additional workaround notes:
- Address alignment of 64 bytes is recommended for maximally
efficient system bus transactions (although 16 byte alignment is
sufficient to avoid the stall condition)
- To support frame sizes that are larger than 4K bytes, there are
two options:
1. Large single buffer frames that span a 4KB page boundary can
be converted into SG frames to avoid transaction splits at
the 4KB boundary,
2. Align the large single buffer to 256B address boundaries,
ensure that the frame address plus offset is 256B aligned.
- If software generated SG frames have buffers that are unaligned
and with random non-multiple of 16 byte lengths, before
transmitting such frames via FMAN, frames will need to be copied
into a new single buffer or multiple buffer SG frame that is
compliant with the three rules listed above.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Detect the presence of the A050385 erratum.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We were erroneously only setting the tx_with_siso_diversity flag in
the Qu B-step configurations for AX101 devices, though we should do
it on all configurations. Add the flag to the other two
configurations, namely Qu C-step and QuZ.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200306151129.1cd986ef467c.Idc0b111475ae3d38b68ae062613c080b574e33e1@changeid
|
|
The TLC configuration did not take into consideration the station's
SMPS configuration, and thus configured rates for 2 NSS even if
static SMPS was reported by the station. Fix this.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200306151129.b4f940d13eca.Ieebfa889d08205a3a961ae0138fb5832e8a0f9c1@changeid
|
|
If the firmware is in a bad state or not initialized fully, sending
the DBGC_SUSPEND_RESUME command fails but we can still collect logs.
Instead of aborting the entire dump process, simply ignore the error.
By removing the last callpoint that was checking the return value, we
can also convert the function to return void.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: 576058330f2d ("iwlwifi: dbg: support debug recording suspend resume command")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200306151129.dcec37b2efd4.I8dcd190431d110a6a0e88095ce93591ccfb3d78d@changeid
|
