| Age | Commit message (Collapse) | Author |
|---|
|
snd_una update should not be done when the same skb is being
sent out.chcr_short_record_handler() sends it again even
though SND_UNA update is already sent for the skb in
chcr_ktls_xmit(), which causes mismatch in un-acked
TCP seq number, later causes problem in sending out
complete record.
Fixes: 429765a149f1 ("chcr: handle partial end part of a record")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HW doesn't need marking TCB closed. This TCB state change
sometimes causes problem to the new connection which gets
the same tid.
Fixes: 34aba2c45024 ("cxgb4/chcr : Register to tls add and del callback")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When sge queue is full and chcr_ktls_xmit_wr_complete()
returns failure, skb is not freed if it is not the last tls record in
this skb, causes refcount never gets freed and tls_dev_del()
never gets called on this connection.
Fixes: 5a4b9fe7fece ("cxgb4/chcr: complete record tx handling")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Taking page refcount is not ideal and causes kernel panic
sometimes. It's better to take tx_ctx lock for the complete
skb transmit, to avoid page cleanup if ACK received in middle.
Fixes: 5a4b9fe7fece ("cxgb4/chcr: complete record tx handling")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2021-04-14
This series provides 3 small fixes to mlx5 driver.
Please pull and let me know if there is any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix this panic by adding more rules to calculate the value of @rss_size_max
which could be used in allocating the queues when bpf is loaded, which,
however, could cause the failure and then trigger the NULL pointer of
vsi->rx_rings. Prio to this fix, the machine doesn't care about how many
cpus are online and then allocates 256 queues on the machine with 32 cpus
online actually.
Once the load of bpf begins, the log will go like this "failed to get
tracking for 256 queues for VSI 0 err -12" and this "setup of MAIN VSI
failed".
Thus, I attach the key information of the crash-log here.
BUG: unable to handle kernel NULL pointer dereference at
0000000000000000
RIP: 0010:i40e_xdp+0xdd/0x1b0 [i40e]
Call Trace:
[2160294.717292] ? i40e_reconfig_rss_queues+0x170/0x170 [i40e]
[2160294.717666] dev_xdp_install+0x4f/0x70
[2160294.718036] dev_change_xdp_fd+0x11f/0x230
[2160294.718380] ? dev_disable_lro+0xe0/0xe0
[2160294.718705] do_setlink+0xac7/0xe70
[2160294.719035] ? __nla_parse+0xed/0x120
[2160294.719365] rtnl_newlink+0x73b/0x860
Fixes: 41c445ff0f48 ("i40e: main driver core")
Co-developed-by: Shujin Li <lishujin@kuaishou.com>
Signed-off-by: Shujin Li <lishujin@kuaishou.com>
Signed-off-by: Jason Xing <xingwanli@kuaishou.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the nft_offload there is the mate flow_dissector with no
ingress_ifindex but with ingress_iftype that only be used
in the software. So if the mask of ingress_ifindex in meta is
0, this meta check should be bypass.
Fixes: 6d65bc64e232 ("net/mlx5e: Add mlx5e_flower_parse_meta support")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Change register setting from bit number to bit mask.
Fixes: b5ede32d3329 ("net/mlx5e: Add support for FEC modes based on 50G per lane links")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Prevent setting of devlink traps on the uplink while in switchdev mode.
In this mode, it is the SW switch responsibility to handle both packets
with a mismatch in destination MAC or VLAN ID. Therefore, there are no
flow steering tables to trap undesirable packets and driver crashes upon
setting a trap.
Fixes: 241dc159391f ("net/mlx5: Notify on trap action by blocking event")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-04-14
This series contains updates to ixgbe and ice drivers.
Alex Duyck fixes a NULL pointer dereference for ixgbe.
Yongxin Liu fixes an unbalanced enable/disable which was causing a call
trace with suspend for ixgbe.
Colin King fixes a potential infinite loop for ice.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 9c63faaa931e443e7abbbee9de0169f1d4710546, which
introduces a suspend/resume regression on Jetson TX2 boards that can be
reproduced every time. Given that the issue that this was supposed to
fix only occurs very sporadically the safest course of action is to
revert before v5.12 and then we can have another go at fixing the more
rare issue in the next release (and perhaps backport it if necessary).
The root cause of the observed problem seems to be that when the system
is suspended, some packets are still in transit. When the descriptors
for these buffers are cleared on resume, the descriptors become invalid
and cause a fatal bus error.
Link: https://lore.kernel.org/r/708edb92-a5df-ecc4-3126-5ab36707e275@nvidia.com/
Reported-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following coccicheck warning:
./drivers/net/ethernet/cavium/liquidio/cn66xx_regs.h:413:6-28:
duplicated argument to & or |
The CN6XXX_INTR_M1UPB0_ERR here is duplicate.
Here should be CN6XXX_INTR_M1UNB0_ERR.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit a14d273ba159 ("net: macb: restore cmp registers on resume path")
introduces the restore of CMP registers on resume path. In case the IP
doesn't support type 2 screeners (zero on DCFG8 register) the
struct macb::rx_fs_list::list is not initialized and thus the
list_for_each_entry(item, &bp->rx_fs_list.list, list) loop introduced in
commit a14d273ba159 ("net: macb: restore cmp registers on resume path")
will access an uninitialized list leading to crash. Thus, initialize
the struct macb::rx_fs_list::list without taking into account if the
IP supports type 2 screeners or not.
Fixes: a14d273ba159 ("net: macb: restore cmp registers on resume path")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a leftover of the below commit.
Fixes: 4f04256c983a ("net: vrf: Drop local rtable and rt6_info")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the unnecessary napi_schedule() call in __ibmvnic_open() since
interrupt_rx() calls napi_schedule_prep/__napi_schedule during every
receive interrupt.
Fixes: ed651a10875f ("ibmvnic: Updated reset handling")
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During adapter reset, do_reset/do_hard_reset calls ibmvnic_open(),
which will calls napi_schedule if previous state is VNIC_CLOSED
(i.e, the reset case, and "ifconfig down" case). So there is no need
for do_reset to call napi_schedule again at the end of the function
though napi_schedule will neglect the request if napi is already
scheduled.
Fixes: ed651a10875f ("ibmvnic: Updated reset handling")
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__ibmvnic_open calls napi_disable without checking whether NAPI polling
has already been disabled or not. This could cause napi_disable
being called twice, which could generate deadlock. For example,
the first napi_disable will spin until NAPI_STATE_SCHED is cleared
by napi_complete_done, then set it again.
When napi_disable is called the second time, it will loop infinitely
because no dev->poll will be running to clear NAPI_STATE_SCHED.
To prevent above scenario from happening, call ibmvnic_napi_disable()
which checks if napi is disabled or not before calling napi_disable.
Fixes: bfc32f297337 ("ibmvnic: Move resource initialization to its own routine")
Suggested-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It has been reported [0] that using pause frames in jumbo mode impacts
performance. There's no available chip documentation, but vendor
drivers r8168 and r8125 don't advertise pause in jumbo mode. So let's
do the same, according to Roman it fixes the issue.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=212617
Fixes: 9cf9b84cc701 ("r8169: make use of phy_set_asym_pause")
Reported-by: Roman Mamedov <rm+bko@romanrm.net>
Tested-by: Roman Mamedov <rm+bko@romanrm.net>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The logic in connect() is currently written with the assumption that
xenbus_watch_pathfmt() will return an error for a node that does not
exist. This assumption is incorrect: xenstore does allow a watch to
be registered for a nonexistent node (and will send notifications
should the node be subsequently created).
As of commit 1f2565780 ("xen-netback: remove 'hotplug-status' once it
has served its purpose"), this leads to a failure when a domU
transitions into XenbusStateConnected more than once. On the first
domU transition into Connected state, the "hotplug-status" node will
be deleted by the hotplug_status_changed() callback in dom0. On the
second or subsequent domU transition into Connected state, the
hotplug_status_changed() callback will therefore never be invoked, and
so the backend will remain stuck in InitWait.
This failure prevents scenarios such as reloading the xen-netfront
module within a domU, or booting a domU via iPXE. There is
unfortunately no way for the domU to work around this dom0 bug.
Fix by explicitly checking for existence of the "hotplug-status" node,
thereby creating the behaviour that was previously assumed to exist.
Signed-off-by: Michael Brown <mbrown@fensystems.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is more correct to use dev_kfree_skb_irq when packets are dropped,
and to use dev_consume_skb_irq when packets are consumed.
Fixes: 0d973388185d ("ibmvnic: Introduce xmit_more support using batched subCRQ hcalls")
Suggested-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A for-loop is using a u8 loop counter that is being compared to
a u32 cmp_dcbcfg->numapp to check for the end of the loop. If
cmp_dcbcfg->numapp is larger than 255 then the counter j will wrap
around to zero and hence an infinite loop occurs. Fix this by making
counter j the same type as cmp_dcbcfg->numapp.
Addresses-Coverity: ("Infinite loop")
Fixes: aeac8ce864d9 ("ice: Recognize 860 as iSCSI port in CEE mode")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
pci_disable_device() called in __ixgbe_shutdown() decreases
dev->enable_cnt by 1. pci_enable_device_mem() which increases
dev->enable_cnt by 1, was removed from ixgbe_resume() in commit
6f82b2558735 ("ixgbe: use generic power management"). This caused
unbalanced increase/decrease. So add pci_enable_device_mem() back.
Fix the following call trace.
ixgbe 0000:17:00.1: disabling already-disabled device
Call Trace:
__ixgbe_shutdown+0x10a/0x1e0 [ixgbe]
ixgbe_suspend+0x32/0x70 [ixgbe]
pci_pm_suspend+0x87/0x160
? pci_pm_freeze+0xd0/0xd0
dpm_run_callback+0x42/0x170
__device_suspend+0x114/0x460
async_suspend+0x1f/0xa0
async_run_entry_fn+0x3c/0xf0
process_one_work+0x1dd/0x410
worker_thread+0x34/0x3f0
? cancel_delayed_work+0x90/0x90
kthread+0x14c/0x170
? kthread_park+0x90/0x90
ret_from_fork+0x1f/0x30
Fixes: 6f82b2558735 ("ixgbe: use generic power management")
Signed-off-by: Yongxin Liu <yongxin.liu@windriver.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ixgbe driver currently generates a NULL pointer dereference when
performing the ethtool loopback test. This is due to the fact that there
isn't a q_vector associated with the test ring when it is setup as
interrupts are not normally added to the test rings.
To address this I have added code that will check for a q_vector before
returning a napi_id value. If a q_vector is not present it will return a
value of 0.
Fixes: b02e5a0ebb17 ("xsk: Propagate napi_id to XDP socket Rx path")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Since commit fee2d546414d ("net: phy: marvell: mv88e6390 temperature
sensor reading"), Linux reports the temperature of Topaz hwmon as
constant -75°C.
This is because switches from the Topaz family (88E6141 / 88E6341) have
the address of the temperature sensor register different from Peridot.
This address is instead compatible with 88E1510 PHYs, as was used for
Topaz before the above mentioned commit.
Create a new mapping table between switch family and PHY ID for families
which don't have a model number. And define PHY IDs for Topaz and Peridot
families.
Create a new PHY ID and a new PHY driver for Topaz's internal PHY.
The only difference from Peridot's PHY driver is the HWMON probing
method.
Prior this change Topaz's internal PHY is detected by kernel as:
PHY [...] driver [Marvell 88E6390] (irq=63)
And afterwards as:
PHY [...] driver [Marvell 88E6341 Family] (irq=63)
Signed-off-by: Pali Rohár <pali@kernel.org>
BugLink: https://github.com/globalscaletechnologies/linux/issues/1
Fixes: fee2d546414d ("net: phy: marvell: mv88e6390 temperature sensor reading")
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check within geneve_xmit_skb/geneve6_xmit_skb that sk_buff structure
is large enough to include IPv4 or IPv6 header, and reject if not. The
geneve_xmit_skb portion and overall idea was contributed by Eric Dumazet.
Fixes a KMSAN-found uninit-value bug reported by syzbot at:
https://syzkaller.appspot.com/bug?id=abe95dc3e3e9667fc23b8d81f29ecad95c6f106f
Suggested-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot+2e406a9ac75bb71d4b7a@syzkaller.appspotmail.com
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the probe fails, we must disable the regulator that was previously
enabled.
This patch is a follow-up to commit ac88c531a5b3
("net: davicom: Fix regulator not turned off on failed probe") which missed
one case.
Fixes: 7994fe55a4a2 ("dm9000: Add regulator and reset support to dm9000")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some trivial spelling mistakes which caught my eye during the
review of the code.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Link: https://lore.kernel.org/r/20210409074223.32480-1-salil.mehta@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ethernet frame length is calculated incorrectly. Depending on
the value of RX_HEAD_PADDING, this may result in ethernet frames
that are too short (cut off at the end), or too long (garbage added
to the end).
Fix by calculating the ethernet frame length correctly. For added
clarity, use the ETH_FCS_LEN constant in the calculation.
Many thanks to Heiner Kallweit for suggesting this solution.
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: 3e21a10fdea3 ("lan743x: trim all 4 bytes of the FCS; not just 2")
Link: https://lore.kernel.org/lkml/20210408172353.21143-1-TheSven73@gmail.com/
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Link: https://lore.kernel.org/r/20210409003904.8957-1-TheSven73@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are a few more bits in the GSWIP_MII_CFG register for which we
did rely on the boot-loader (or the hardware defaults) to set them up
properly.
For some external RMII PHYs we need to select the GSWIP_MII_CFG_RMII_CLK
bit and also we should un-set it for non-RMII PHYs. The
GSWIP_MII_CFG_RMII_CLK bit is ignored for other PHY connection modes.
The GSWIP IP also supports in-band auto-negotiation for RGMII PHYs when
the GSWIP_MII_CFG_RGMII_IBS bit is set. Clear this bit always as there's
no known hardware which uses this (so it is not tested yet).
Clear the xMII isolation bit when set at initialization time if it was
previously set by the bootloader. Not doing so could lead to no traffic
(neither RX nor TX) on a port with this bit set.
While here, also add the GSWIP_MII_CFG_RESET bit. We don't need to
manage it because this bit is self-clearning when set. We still add it
here to get a better overview of the GSWIP_MII_CFG register.
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Cc: stable@vger.kernel.org
Suggested-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PHY auto polling on the GSWIP hardware can be used so link changes
(speed, link up/down, etc.) can be detected automatically. Internally
GSWIP reads the PHY's registers for this functionality. Based on this
automatic detection GSWIP can also automatically re-configure it's port
settings. Unfortunately this auto polling (and configuration) mechanism
seems to cause various issues observed by different people on different
devices:
- FritzBox 7360v2: the two Gbit/s ports (connected to the two internal
PHY11G instances) are working fine but the two Fast Ethernet ports
(using an AR8030 RMII PHY) are completely dead (neither RX nor TX are
received). It turns out that the AR8030 PHY sets the BMSR_ESTATEN bit
as well as the ESTATUS_1000_TFULL and ESTATUS_1000_XFULL bits. This
makes the PHY auto polling state machine (rightfully?) think that the
established link speed (when the other side is Gbit/s capable) is
1Gbit/s.
- None of the Ethernet ports on the Zyxel P-2812HNU-F1 (two are
connected to the internal PHY11G GPHYs while the other three are
external RGMII PHYs) are working. Neither RX nor TX traffic was
observed. It is not clear which part of the PHY auto polling state-
machine caused this.
- FritzBox 7412 (only one LAN port which is connected to one of the
internal GPHYs running in PHY22F / Fast Ethernet mode) was seeing
random disconnects (link down events could be seen). Sometimes all
traffic would stop after such disconnect. It is not clear which part
of the PHY auto polling state-machine cauased this.
- TP-Link TD-W9980 (two ports are connected to the internal GPHYs
running in PHY11G / Gbit/s mode, the other two are external RGMII
PHYs) was affected by similar issues as the FritzBox 7412 just without
the "link down" events
Switch to software based configuration instead of PHY auto polling (and
letting the GSWIP hardware configure the ports automatically) for the
following link parameters:
- link up/down
- link speed
- full/half duplex
- flow control (RX / TX pause)
After a big round of manual testing by various people (who helped test
this on OpenWrt) it turns out that this fixes all reported issues.
Additionally it can be considered more future proof because any
"quirk" which is implemented for a PHY on the driver side can now be
used with the GSWIP hardware as well because Linux is in control of the
link parameters.
As a nice side-effect this also solves a problem where fixed-links were
not supported previously because we were relying on the PHY auto polling
mechanism, which cannot work for fixed-links as there's no PHY from
where it can read the registers. Configuring the link settings on the
GSWIP ports means that we now use the settings from device-tree also for
ports with fixed-links.
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Fixes: 3e6fdeb28f4c33 ("net: dsa: lantiq_gswip: Let GSWIP automatically set the xMII clock")
Cc: stable@vger.kernel.org
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-04-08
This series contains updates to i40e and ice drivers.
Grzegorz fixes the ordering of parameters to i40e_aq_get_phy_register()
which is causing incorrect information to be reported.
Arkadiusz fixes various sparse issues reported on the i40e driver.
Yongxin Liu fixes a memory leak with aRFS following resume from suspend
for ice driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In ice_suspend(), ice_clear_interrupt_scheme() is called, and then
irq_free_descs() will be eventually called to free irq and its descriptor.
In ice_resume(), ice_init_interrupt_scheme() is called to allocate new
irqs. However, in ice_rebuild_arfs(), struct irq_glue and struct cpu_rmap
maybe cannot be freed, if the irqs that released in ice_suspend() were
reassigned to other devices, which makes irq descriptor's affinity_notify
lost.
So call ice_free_cpu_rx_rmap() before ice_clear_interrupt_scheme(), which
can make sure all irq_glue and cpu_rmap can be correctly released before
corresponding irq and descriptor are released.
Fix the following memory leak.
unreferenced object 0xffff95bd951afc00 (size 512):
comm "kworker/0:1", pid 134, jiffies 4294684283 (age 13051.958s)
hex dump (first 32 bytes):
18 00 00 00 18 00 18 00 70 fc 1a 95 bd 95 ff ff ........p.......
00 00 ff ff 01 00 ff ff 02 00 ff ff 03 00 ff ff ................
backtrace:
[<0000000072e4b914>] __kmalloc+0x336/0x540
[<0000000054642a87>] alloc_cpu_rmap+0x3b/0xb0
[<00000000f220deec>] ice_set_cpu_rx_rmap+0x6a/0x110 [ice]
[<000000002370a632>] ice_probe+0x941/0x1180 [ice]
[<00000000d692edba>] local_pci_probe+0x47/0xa0
[<00000000503934f0>] work_for_cpu_fn+0x1a/0x30
[<00000000555a9e4a>] process_one_work+0x1dd/0x410
[<000000002c4b414a>] worker_thread+0x221/0x3f0
[<00000000bb2b556b>] kthread+0x14c/0x170
[<00000000ad2cf1cd>] ret_from_fork+0x1f/0x30
unreferenced object 0xffff95bd81b0a2a0 (size 96):
comm "kworker/0:1", pid 134, jiffies 4294684283 (age 13051.958s)
hex dump (first 32 bytes):
38 00 00 00 01 00 00 00 e0 ff ff ff 0f 00 00 00 8...............
b0 a2 b0 81 bd 95 ff ff b0 a2 b0 81 bd 95 ff ff ................
backtrace:
[<00000000582dd5c5>] kmem_cache_alloc_trace+0x31f/0x4c0
[<000000002659850d>] irq_cpu_rmap_add+0x25/0xe0
[<00000000495a3055>] ice_set_cpu_rx_rmap+0xb4/0x110 [ice]
[<000000002370a632>] ice_probe+0x941/0x1180 [ice]
[<00000000d692edba>] local_pci_probe+0x47/0xa0
[<00000000503934f0>] work_for_cpu_fn+0x1a/0x30
[<00000000555a9e4a>] process_one_work+0x1dd/0x410
[<000000002c4b414a>] worker_thread+0x221/0x3f0
[<00000000bb2b556b>] kthread+0x14c/0x170
[<00000000ad2cf1cd>] ret_from_fork+0x1f/0x30
Fixes: 769c500dcc1e ("ice: Add advanced power mgmt for WoL")
Signed-off-by: Yongxin Liu <yongxin.liu@windriver.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Set proper return values inside error checking if-statements.
Previously following warning was produced when compiling against sparse.
i40e_main.c:15162 i40e_init_recovery_mode() warn: missing error code 'err'
Fixes: 4ff0ee1af0169 ("i40e: Introduce recovery mode support")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Remove vsi->netdev->name from the trace.
This is redundant information. With the devinfo trace, the adapter
is already identifiable.
Previously following error was produced when compiling against sparse.
i40e_main.c:2571 i40e_sync_vsi_filters() error:
we previously assumed 'vsi->netdev' could be null (see line 2323)
Fixes: b603f9dc20af ("i40e: Log info when PF is entering and leaving Allmulti mode.")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Init pointer with NULL in default switch case statement.
Previously the error was produced when compiling against sparse.
i40e_debugfs.c:582 i40e_dbg_dump_desc() error: uninitialized symbol 'ring'.
Fixes: 44ea803e2fa7 ("i40e: introduce new dump desc XDP command")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Remove error handling through pointers. Instead use plain int
to return value from i40e_run_xdp(...).
Previously:
- sparse errors were produced during compilation:
i40e_txrx.c:2338 i40e_run_xdp() error: (-2147483647) too low for ERR_PTR
i40e_txrx.c:2558 i40e_clean_rx_irq() error: 'skb' dereferencing possible ERR_PTR()
- sk_buff* was used to return value, but it has never had valid
pointer to sk_buff. Returned value was always int handled as
a pointer.
Fixes: 0c8493d90b6b ("i40e: add XDP support for pass and drop actions")
Fixes: 2e6893123830 ("i40e: split XDP_TX tail and XDP_REDIRECT map flushing")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Change parameters order in aq_get_phy_register() due to wrong
statistics in PHY reported by ethtool. Previously all PHY statistics were
exactly the same for all interfaces
Now statistics are reported correctly - different for different interfaces
Fixes: 0514db37dd78 ("i40e: Extend PHY access with page change flag")
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
cfg80211_inform_bss expects to receive a TSF value, but is given the
time since boot in nanoseconds. TSF values are expected to be at
microsecond scale rather than nanosecond scale.
Signed-off-by: A. Cody Schuffelen <schuffelen@google.com>
Link: https://lore.kernel.org/r/20210318200419.1421034-1-schuffelen@google.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Multiple ttys try to claim the same the minor number causing a double
unregistration of the same device. The first unregistration succeeds
but the next one results in a null-ptr-deref.
The get_free_serial_index() function returns an available minor number
but doesn't assign it immediately. The assignment is done by the caller
later. But before this assignment, calls to get_free_serial_index()
would return the same minor number.
Fix this by modifying get_free_serial_index to assign the minor number
immediately after one is found to be and rename it to obtain_minor()
to better reflect what it does. Similary, rename set_serial_by_index()
to release_minor() and modify it to free up the minor number of the
given hso_serial. Every obtain_minor() should have corresponding
release_minor() call.
Fixes: 72dc1c096c705 ("HSO: add option hso driver")
Reported-by: syzbot+c49fe6089f295a05e6f8@syzkaller.appspotmail.com
Tested-by: syzbot+c49fe6089f295a05e6f8@syzkaller.appspotmail.com
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.12
Third, and last, set of fixes for v5.12. Small fixes, iwlwifi having
most of them. brcmfmac regression caused by cfg80211 changes is the
most important here.
iwlwifi
* fix a lockdep warning
* fix regulatory feature detection in certain firmware versions
* new hardware support
* fix lockdep warning
* mvm: fix beacon protection checks
mt76
* mt7921: fix airtime reporting
brcmfmac
* fix a deadlock regression
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some drivers clear the 'ethtool_link_ksettings' struct in their
get_link_ksettings() callback, before populating it with actual values.
Such drivers will set the new 'link_mode' field to zero, resulting in
user space receiving wrong link mode information given that zero is a
valid value for the field.
Another problem is that some drivers (notably tun) can report random
values in the 'link_mode' field. This can result in a general protection
fault when the field is used as an index to the 'link_mode_params' array
[1].
This happens because such drivers implement their set_link_ksettings()
callback by simply overwriting their private copy of
'ethtool_link_ksettings' struct with the one they get from the stack,
which is not always properly initialized.
Fix these problems by removing 'link_mode' from 'ethtool_link_ksettings'
and instead have drivers call ethtool_params_from_link_mode() with the
current link mode. The function will derive the link parameters (e.g.,
speed) from the link mode and fill them in the 'ethtool_link_ksettings'
struct.
v3:
* Remove link_mode parameter and derive the link parameters in
the driver instead of passing link_mode parameter to ethtool
and derive it there.
v2:
* Introduce 'cap_link_mode_supported' instead of adding a
validity field to 'ethtool_link_ksettings' struct.
[1]
general protection fault, probably for non-canonical address 0xdffffc00f14cc32c: 0000 [#1] PREEMPT SMP KASAN
KASAN: probably user-memory-access in range [0x000000078a661960-0x000000078a661967]
CPU: 0 PID: 8452 Comm: syz-executor360 Not tainted 5.11.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:__ethtool_get_link_ksettings+0x1a3/0x3a0 net/ethtool/ioctl.c:446
Code: b7 3e fa 83 fd ff 0f 84 30 01 00 00 e8 16 b0 3e fa 48 8d 3c ed 60 d5 69 8a 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <0f> b6 14 02 48 89 f8 83 e0 07 83 c0 03
+38 d0 7c 08 84 d2 0f 85 b9
RSP: 0018:ffffc900019df7a0 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: ffff888026136008 RCX: 0000000000000000
RDX: 00000000f14cc32c RSI: ffffffff873439ca RDI: 000000078a661960
RBP: 00000000ffff8880 R08: 00000000ffffffff R09: ffff88802613606f
R10: ffffffff873439bc R11: 0000000000000000 R12: 0000000000000000
R13: ffff88802613606c R14: ffff888011d0c210 R15: ffff888011d0c210
FS: 0000000000749300(0000) GS:ffff8880b9c00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000004b60f0 CR3: 00000000185c2000 CR4: 00000000001506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
linkinfo_prepare_data+0xfd/0x280 net/ethtool/linkinfo.c:37
ethnl_default_notify+0x1dc/0x630 net/ethtool/netlink.c:586
ethtool_notify+0xbd/0x1f0 net/ethtool/netlink.c:656
ethtool_set_link_ksettings+0x277/0x330 net/ethtool/ioctl.c:620
dev_ethtool+0x2b35/0x45d0 net/ethtool/ioctl.c:2842
dev_ioctl+0x463/0xb70 net/core/dev_ioctl.c:440
sock_do_ioctl+0x148/0x2d0 net/socket.c:1060
sock_ioctl+0x477/0x6a0 net/socket.c:1177
vfs_ioctl fs/ioctl.c:48 [inline]
__do_sys_ioctl fs/ioctl.c:753 [inline]
__se_sys_ioctl fs/ioctl.c:739 [inline]
__x64_sys_ioctl+0x193/0x200 fs/ioctl.c:739
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: c8907043c6ac9 ("ethtool: Get link mode in use instead of speed and duplex parameters")
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Memory allocated by kvzalloc() should be freed by kvfree().
Fixes: 34ca65352ddf2 ("net/mlx5: E-Switch, Indirect table infrastructur")
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Make sure to modify uplink port to follow only if the uplink_follow
capability is set as required by the HW spec. Failure to do so causes
traffic to the uplink representor net device to cease after switching to
switchdev mode.
Fixes: 7d0314b11cdd ("net/mlx5e: Modify uplink state on interface up/down")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When changing type with TUNSETLINK ioctl command, set tun->dev->addr_len
to match the appropriate type, using new tun_get_addr_len utility function
which returns appropriate address length for given type. Fixes a
KMSAN-found uninit-value bug reported by syzbot at:
https://syzkaller.appspot.com/bug?id=0766d38c656abeace60621896d705743aeefed51
Reported-by: syzbot+001516d86dbe88862cec@syzkaller.appspotmail.com
Diagnosed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the VF down state bit is cleared after VF sending
link status request command. There is problem that when VF gets
link status replied from PF, the down state bit may still set
as 1. In this case, the link status replied from PF will be
ignored and always set VF link status to down.
To fix this problem, clear VF down state bit before VF requests
link status.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2021-04-06
this is a pull request of 1 patch for net/master.
The patch is by me and fixes the SPI half duplex support in the
mcp251x CAN driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
pci_resource_start() is not a good indicator to determine if a PCI
resource exists or not, since the resource may start at address 0.
This is seen when trying to instantiate the driver in qemu for riscv32
or riscv64.
pci 0000:00:01.0: reg 0x10: [io 0x0000-0x001f]
pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000001f]
...
pcnet32: card has no PCI IO resources, aborting
Use pci_resouce_len() instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Xuan Zhuo reported that commit 3226b158e67c ("net: avoid 32 x truesize
under-estimation for tiny skbs") brought a ~10% performance drop.
The reason for the performance drop was that GRO was forced
to chain sk_buff (using skb_shinfo(skb)->frag_list), which
uses more memory but also cause packet consumers to go over
a lot of overhead handling all the tiny skbs.
It turns out that virtio_net page_to_skb() has a wrong strategy :
It allocates skbs with GOOD_COPY_LEN (128) bytes in skb->head, then
copies 128 bytes from the page, before feeding the packet to GRO stack.
This was suboptimal before commit 3226b158e67c ("net: avoid 32 x truesize
under-estimation for tiny skbs") because GRO was using 2 frags per MSS,
meaning we were not packing MSS with 100% efficiency.
Fix is to pull only the ethernet header in page_to_skb()
Then, we change virtio_net_hdr_to_skb() to pull the missing
headers, instead of assuming they were already pulled by callers.
This fixes the performance regression, but could also allow virtio_net
to accept packets with more than 128bytes of headers.
Many thanks to Xuan Zhuo for his report, and his tests/help.
Fixes: 3226b158e67c ("net: avoid 32 x truesize under-estimation for tiny skbs")
Reported-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Link: https://www.spinics.net/lists/netdev/msg731397.html
Co-Developed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: virtualization@lists.linux-foundation.org
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In bcm4908_enet_dma_alloc, if callee bcm4908_dma_alloc_buf_descs() failed,
it will free the ring->cpu_addr by dma_free_coherent() and return error.
Then bcm4908_enet_dma_free() will be called, and free the same cpu_addr
by dma_free_coherent() again.
My patch set ring->cpu_addr to NULL after it is freed in
bcm4908_dma_alloc_buf_descs() to avoid the double free.
Fixes: 4feffeadbcb2e ("net: broadcom: bcm4908enet: add BCM4908 controller driver")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some SPI host controllers do not support full-duplex SPI transfers.
The function mcp251x_spi_trans() does a full duplex transfer. It is
used in several places in the driver, where a TX half duplex transfer
is sufficient.
To fix support for half duplex SPI host controllers, this patch
introduces a new function mcp251x_spi_write() and changes all callers
that do a TX half duplex transfer to use mcp251x_spi_write().
Fixes: e0e25001d088 ("can: mcp251x: add support for half duplex controllers")
Link: https://lore.kernel.org/r/20210330100246.1074375-1-mkl@pengutronix.de
Cc: Tim Harvey <tharvey@gateworks.com>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Reported-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
