summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2019-02-24net: phy: fix reading fixed phy statusHeiner Kallweit
With the switch to phy_resolve_aneg_linkmode() we don't read from the chip any longer what is advertised but use phydev->advertising directly. For a fixed phy however this bitmap is empty so far, what results in no common mode being found. This breaks DSA. Fix this by advertising everything that is supported. For a normal phy this done by phy_probe(). Fixes: 5502b218e001 ("net: phy: use phy_resolve_aneg_linkmode in genphy_read_status") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Tested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: phy: improve auto-neg emulation in swphyHeiner Kallweit
Auto-neg emulation currently doesn't set bit BMCR_ANENABLE in BMCR, add this. Users will ignore speed and duplex settings in BMCR because we're emulating auto-neg, therefore we can remove related code. See also following discussion [0]. [0] https://marc.info/?t=155041784900002&r=1&w=2 Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Tested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: dsa: mv88e6xxx: Release lock while requesting IRQAndrew Lunn
There is no need to hold the register lock while requesting the GPIO interrupt. By not holding it we can also avoid a false positive lockdep splat. Reported-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: dsa: mv88e6xxx: Add lockdep classes to fix false positive splatAndrew Lunn
The following false positive lockdep splat has been observed. ====================================================== WARNING: possible circular locking dependency detected 4.20.0+ #302 Not tainted ------------------------------------------------------ systemd-udevd/160 is trying to acquire lock: edea6080 (&chip->reg_lock){+.+.}, at: __setup_irq+0x640/0x704 but task is already holding lock: edff0340 (&desc->request_mutex){+.+.}, at: __setup_irq+0xa0/0x704 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (&desc->request_mutex){+.+.}: mutex_lock_nested+0x1c/0x24 __setup_irq+0xa0/0x704 request_threaded_irq+0xd0/0x150 mv88e6xxx_probe+0x41c/0x694 [mv88e6xxx] mdio_probe+0x2c/0x54 really_probe+0x200/0x2c4 driver_probe_device+0x5c/0x174 __driver_attach+0xd8/0xdc bus_for_each_dev+0x58/0x7c bus_add_driver+0xe4/0x1f0 driver_register+0x7c/0x110 mdio_driver_register+0x24/0x58 do_one_initcall+0x74/0x2e8 do_init_module+0x60/0x1d0 load_module+0x1968/0x1ff4 sys_finit_module+0x8c/0x98 ret_fast_syscall+0x0/0x28 0xbedf2ae8 -> #0 (&chip->reg_lock){+.+.}: __mutex_lock+0x50/0x8b8 mutex_lock_nested+0x1c/0x24 __setup_irq+0x640/0x704 request_threaded_irq+0xd0/0x150 mv88e6xxx_g2_irq_setup+0xcc/0x1b4 [mv88e6xxx] mv88e6xxx_probe+0x44c/0x694 [mv88e6xxx] mdio_probe+0x2c/0x54 really_probe+0x200/0x2c4 driver_probe_device+0x5c/0x174 __driver_attach+0xd8/0xdc bus_for_each_dev+0x58/0x7c bus_add_driver+0xe4/0x1f0 driver_register+0x7c/0x110 mdio_driver_register+0x24/0x58 do_one_initcall+0x74/0x2e8 do_init_module+0x60/0x1d0 load_module+0x1968/0x1ff4 sys_finit_module+0x8c/0x98 ret_fast_syscall+0x0/0x28 0xbedf2ae8 other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&desc->request_mutex); lock(&chip->reg_lock); lock(&desc->request_mutex); lock(&chip->reg_lock); &desc->request_mutex refer to two different mutex. #1 is the GPIO for the chip interrupt. #2 is the chained interrupt between global 1 and global 2. Add lockdep classes to the GPIO interrupt to avoid this. Reported-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: hns3: fix improper error handling for hns3_client_startHuazhong Tan
If hns3_client_start() failed in the hns3_client_init(), register_dev() should be undo in its error handling. Fixes: a6d818e31d08 ("net: hns3: Add vport alive state checking support") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: hns3: fix setting of the hns reset_type for rdma hw errorsShiju Jose
Presently the hns reset_type for the roce errors is set in the hclge_log_and_clear_rocee_ras_error function. This function is also called to detect and clear roce errors while enabling the rdma error interrupts. However there is no hns reset requested for this case. This can cause issue of wrong reset_type used with subsequent hns reset as the reset_type set in the above case was not cleared. This patch moves setting of hns reset_type for the roce errors from hclge_log_and_clear_rocee_ras_error function to hclge_handle_rocee_ras_error. Fixes: 630ba007f475 ("net: hns3: add handling of RDMA RAS errors") Reported-by: Huazhong Tan <tanhuazhong@huawei.com> Reported-by: Xiaofei Tan <tanxiaofei@huawei.com> Signed-off-by: Shiju Jose <shiju.jose@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: hns3: fix get VF RSS issueJian Shen
For revision 0x20, VF shares the same RSS config with PF. In original codes, it always return 0 when query RSS hash key for VF. This patch fixes it by return the hash key got from PF. Fixes: 374ad291762a ("net: hns3: net: hns3: Add RSS general configuration support for VF") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: hns3: enable VF VLAN filter for each VF when initializingJian Shen
For revision 0x21, the switch of VF VLAN filter is per function. It's necessary to enable VF VLAN filter for each VF when initializing. Otherwise, VF will be able to receive broadcast packets with unknown VLAN when PF enters promisc mode. Fixes: 64d114f0a750 ("net: hns3: Add egress/ingress vlan filter for revision 0x21") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: hns3: add support to config depth for tx|rx ring separatelyPeng Li
This patch adds support to config depth for tx|rx ring separately by ethtool command "-G". Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: hns3: remove hnae3_get_bit in data pathYunsheng Lin
The hnae3_get_bit uses hnae3_get_field, and hnae3_get_field masks the data, which is unnecessary in data path. Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: hns3: replace hnae3_set_bit and hnae3_set_field in data pathYunsheng Lin
hnae3_set_bit and hnae3_set_field masks the data before setting the field or bit, which is unnecessary because the data is already zero initialized. Suggested-by: John Garry <john.garry@huawei.com> Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: hns3: add unlikely for error handling in data pathYunsheng Lin
This patch adds unlikely hint for error handling in critical data path. Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: hns3: remove some ops in struct hns3_nic_opsYunsheng Lin
The fill_desc ops has only one implementation, and get_rxd_bnum has not been used, so this patch removes them. Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: hns3: limit some variable scope in critical data pathYunsheng Lin
This patch limits some variables' scope as much as possible in hns3_fill_desc. Also, only set l3_type and l4_type when necessary. Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Huazhong tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: hns3: avoid mult + div op in critical data pathYunsheng Lin
This patch uses shift offset to avoid doing mult and div operation. Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: hns3: add xps setting support for hns3 driverYunsheng Lin
This patch adds xps setting support for hns3 driver based on the interrupt affinity info. Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24mlxsw: spectrum_acl: Add vregion migration end tracepointJiri Pirko
Hit the new tracepoint once the vregion migration ends. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24mlxsw: spectrum_acl: Don't take mutex in mlxsw_sp_acl_tcam_vregion_rehash_work()Jiri Pirko
Other mutexes are taking care of proper locking for this, no longer needed to take RTNL mutex here. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24mlxsw: spectrum_acl: Remove RTNL lock assertions from ERP codeJiri Pirko
No longer require RTNL lock in this code. Newly introduced mutexes take care of guarding objagg and bloom filter. There is no need to guard gen_pool_alloc()/gen_pool_free() as they are fine to be called lockless. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24mlxsw: spectrum_acl: Don't take rtnl lock during vregion_rehash_intrvl_set()Jiri Pirko
Relax dependency on rtnl mutex during vregion_rehash_intrvl_set(). The vregion list is protected with newly introduced mutex. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24mlxsw: spectrum_acl: Introduce a mutex to guard objagg instance manipulationJiri Pirko
Protect objagg structures by adding a mutex to ERP code and take it during the structure manipulation. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24mlxsw: spectrum_acl: Enable vregion rehash per-profileJiri Pirko
For MR ACL profile is does not make sense to do periodical rehashes, as there is only one mask in use during the whole vregion lifetime. Therefore periodical work is scheduled but the rehash never happens. So allow to enable/disable rehash for the whole group, which is added per-profile. Disable rehashing for MR profile. Addition to the vregion list is done only in case the rehash is enable on the particular vregion. Also, the addition is moved after delayed work init to avoid schedule of uninitialized work from vregion_rehash_intrvl_set(). Symmetrically, deletion from the list is done before canceling the delayed work so it is not scheduled by vregion_rehash_intrvl_set() again. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24mlxsw: spectrum_acl: Introduce mutex to guard Bloom Filter updatesJiri Pirko
Bloom filter is shared within multiple regions. For updates, it needs to be guarded by a separate mutex. Do that in order to not rely on RTNL mutex. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24mlxsw: spectrum_acl: Introduce vregion mutexJiri Pirko
In order to remove dependency on RTNL, introduce a mutex to guard vregion structure, list of chunks and list of entries in chunks. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24mlxsw: spectrum_acl: Refactor vregion association codeJiri Pirko
Refactor existing _vchunk_assoc/_vchunk_deassoc() functions into _vregion_get()/_vregion_put() to make the code simpler and prepared for vregion locking. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24mlxsw: spectrum_acl: Introduce a mutex to guard region list updatesJiri Pirko
In order to remove RTNL lock dependency, it is needed to protect the regions list in a group. Introduce a mutex to do the job. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24mlxsw: spectrum_acl: Split TCAM group structure into twoJiri Pirko
Make the existing group structure to contain fields needed for HW region list manipulations. Move the rest of the fields into new vgroup struct. This makes layering cleaner as the vgroup struct is on higher level than low-level group struct. Also, this makes it possible to introduce fine-grained locking. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24mlxsw: spectrum_acl: Remove unused ops field from group structureJiri Pirko
Never used, remove it. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: dsa: microchip: add port_cleanup functionTristram Ha
Add port_cleanup function to reset some device variables when the port is disabled. Add a mutex to make sure changing those variables is thread-safe. Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: dsa: microchip: remove unnecessary include headersTristram Ha
Remove unnecessary header include. Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: dsa: microchip: get port link statusTristram Ha
Get port link status to know whether to read MIB counters when the link is going down. Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: dsa: microchip: add MIB counter reading supportTristram Ha
Add background MIB counter reading support. Port MIB counters should only be read when there is link. Otherwise it is a waste of time as hardware never increases those counters. There are exceptions as some switches keep track of dropped counts no matter what. Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: dsa: microchip: prepare PHY for proper advertisementTristram Ha
Prepare PHY for proper advertisement as sometimes the PHY in the switch has its own problems even though it may share the PHY id from regular PHY but the fixes in the PHY driver do not apply. Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: phy: marvell10g: add support for the 88x2110 PHYMaxime Chevallier
This patch adds support for the 88x2110 PHY, which is similar to the already supported 88x3310 PHY without the SFP interface. It supports 10/100/1000BASET along with 2.5GBASET, 5GBASET and 10GBASET, with the same interface modes that are used by the 3310. This PHY don't have the same issue as the 88x3310 regarding 2.5/5G abilities, and correctly follows the 802.3bz standard to list the supported abilities. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Suggested-by: Antoine Tenart <antoine.tenart@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: mvpp2: Add 2.5GBaseT supportMaxime Chevallier
The PPv2 controller is able to support 2.5G speeds, allowing to use 2.5GBASET in conjunction with PHYs that use 2500BASEX as their MII interface when using this mode. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: phy: marvell10g: Force reading of 2.5/5GMaxime Chevallier
As per 802.3bz, if bit 14 of (1.11) "PMA Extended Abilities" indicates whether or not we should read register (1.21) "2.52/5G PMA Extended Abilities", which contains information on the support of 2.5GBASET and 5GBASET. After testing on several variants of PHYS of this family, it appears that bit 14 in (1.11) isn't always set when it should be. PHYs 88X3310 (on MacchiatoBin) and 88E2010 do support 2.5G and 5GBASET, but don't have 1.11.14 set. Their register 1.21 is filled with the correct values, indicating 2.5G and 5G support. PHYs 88E2110 do have their 1.11.14 bit set, as it should. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: phy: marvell10g: Use a #define for 88X3310 family idMaxime Chevallier
The PHY ID corresponding to the 88X3310 is also used for other PHYs in the same family, such as the 88E2010. Use a #define for the PHY id, that ignores the last nibble. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: phy: marvell10g: Use 2500BASEX when using 2.5GBASETMaxime Chevallier
The Marvell Alaska family of PHYs supports 2.5GBaseT and 5GBaseT modes, as defined in the 802.3bz specification. Upon establishing a 2.5GBASET link, the PHY will reconfigure it's MII interface to 2500BASEX. At 5G, the PHY will reconfigure it's interface to 5GBASE-R, but this mode isn't supported by any MAC for now. This was tested with : - The 88X3310, which is on the MacchiatoBin - The 88E2010, an Alaska PHY that has no fiber interfaces, and is limited to 5G maximum speed. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: phy: marvell10g: Use linkmode_set_bit helper instead of __set_bitMaxime Chevallier
Cosmetic patch making use of helpers dedicated to linkmodes handling. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: phy: marvell10g: Use get_features to get the PHY abilitiesMaxime Chevallier
The Alaska family of 10G PHYs has more abilities than the ones listed in PHY_10GBIT_FULL_FEATURES, the exact list depending on the model. Make use of the newly introduced .get_features call to build this list, using genphy_c45_pma_read_abilities to build the list of supported linkmodes, and adding autoneg ability based on what's reported by the AN MMD. .config_init is still used to validate the interface_mode. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: phy: check PMAPMD link status only in genphy_c45_read_linkHeiner Kallweit
The current code reports a link as up if all devices (except a few blacklisted ones) report the link as up. This breaks Aquantia AQCS109 for lower speeds because on this PHY the PCS link status reflects a 10G link only. For Marvell there's a similar issue, therefore PHYXS device isn't checked. There may be more PHYs where depending on the mode the link status of only selected devices is relevant. For now it seems to be sufficient to check the link status of the PMAPMD device only. Leave the loop in the code to be prepared in case we have to add functionality to check more than one device, depending on the mode. Successfully tested on a board with an AQCS109. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: Remove switchdev.h inclusion from team/bond/vlanFlorian Fainelli
This is no longer necessary after eca59f691566 ("net: Remove support for bridge bypass ndos from stacked devices") Suggested-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andy Gospodarek <andy@greyhouse.net> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24nfp: Remove switchdev.h inclusionFlorian Fainelli
This is no longer necessary after a5084bb71fa4 ("nfp: Implement ndo_get_port_parent_id()") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: lantiq: Do not use eth_change_mtu()Hauke Mehrtens
eth_change_mtu() is not needed any more, the networking subsystem will call it automatically when this callback is not implemented. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24vxlan: add ndo_change_proto_down supportAndy Roulin
Add ndo_change_proto_down support through dev_change_proto_down_generic for use by control protocols like VRRPD. Signed-off-by: Andy Roulin <aroulin@cumulusnetworks.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24macvlan: add ndo_change_proto_down supportAndy Roulin
Add ndo_change_proto_down support through dev_change_proto_down_generic for use by control protocols like VRRPD. Signed-off-by: Andy Roulin <aroulin@cumulusnetworks.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24net: phy: let genphy_c45_read_abilities also check aneg capabilityHeiner Kallweit
When using genphy_c45_read_abilities() as get_features callback we also have to set the autoneg capability in phydev->supported. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Three conflicts, one of which, for marvell10g.c is non-trivial and requires some follow-up from Heiner or someone else. The issue is that Heiner converted the marvell10g driver over to use the generic c45 code as much as possible. However, in 'net' a bug fix appeared which makes sure that a new local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0 is cleared. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds
Pull networking fixes from David Miller: "Hopefully the last pull request for this release. Fingers crossed: 1) Only refcount ESP stats on full sockets, from Martin Willi. 2) Missing barriers in AF_UNIX, from Al Viro. 3) RCU protection fixes in ipv6 route code, from Paolo Abeni. 4) Avoid false positives in untrusted GSO validation, from Willem de Bruijn. 5) Forwarded mesh packets in mac80211 need more tailroom allocated, from Felix Fietkau. 6) Use operstate consistently for linkup in team driver, from George Wilkie. 7) ThunderX bug fixes from Vadim Lomovtsev. Mostly races between VF and PF code paths. 8) Purge ipv6 exceptions during netdevice removal, from Paolo Abeni. 9) nfp eBPF code gen fixes from Jiong Wang. 10) bnxt_en firmware timeout fix from Michael Chan. 11) Use after free in udp/udpv6 error handlers, from Paolo Abeni. 12) Fix a race in x25_bind triggerable by syzbot, from Eric Dumazet" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits) net: phy: realtek: Dummy IRQ calls for RTL8366RB tcp: repaired skbs must init their tso_segs net/x25: fix a race in x25_bind() net: dsa: Remove documentation for port_fdb_prepare Revert "bridge: do not add port to router list when receives query with source 0.0.0.0" selftests: fib_tests: sleep after changing carrier. again. net: set static variable an initial value in atl2_probe() net: phy: marvell10g: Fix Multi-G advertisement to only advertise 10G bpf, doc: add bpf list as secondary entry to maintainers file udp: fix possible user after free in error handler udpv6: fix possible user after free in error handler fou6: fix proto error handler argument type udpv6: add the required annotation to mib type mdio_bus: Fix use-after-free on device_register fails net: Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255 bnxt_en: Wait longer for the firmware message response to complete. bnxt_en: Fix typo in firmware message timeout logic. nfp: bpf: fix ALU32 high bits clearance bug nfp: bpf: fix code-gen bug on BPF_ALU | BPF_XOR | BPF_K Documentation: networking: switchdev: Update port parent ID section ...
2019-02-23net: phy: realtek: Dummy IRQ calls for RTL8366RBLinus Walleij
This fixes a regression introduced by commit 0d2e778e38e0ddffab4bb2b0e9ed2ad5165c4bf7 "net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt". This assumes that a PHY cannot trigger interrupt unless it has .config_intr() or .ack_interrupt() implemented. A later patch makes the code assume both need to be implemented for interrupts to be present. But this PHY (which is inside a DSA) will happily fire interrupts without either callback. Implement dummy callbacks for .config_intr() and .ack_interrupt() in the phy header to fix this. Tested on the RTL8366RB on D-Link DIR-685. Fixes: 0d2e778e38e0 ("net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt") Cc: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit (git 2.34.1) at 2025-04-22 15:07:42 +0000