| Age | Commit message (Collapse) | Author |
|---|
|
Pull networking fixes from David Miller:
1) Fix type of bind option flag in af_xdp, from Baruch Siach.
2) Fix use after free in bpf_xdp_link_release(), from Xuan Zhao.
3) PM refcnt imbakance in r8152, from Takashi Iwai.
4) Sign extension ug in liquidio, from Colin Ian King.
5) Mising range check in s390 bpf jit, from Colin Ian King.
6) Uninit value in caif_seqpkt_sendmsg(), from Ziyong Xuan.
7) Fix skb page recycling race, from Ilias Apalodimas.
8) Fix memory leak in tcindex_partial_destroy_work, from Pave Skripkin.
9) netrom timer sk refcnt issues, from Nguyen Dinh Phi.
10) Fix data races aroun tcp's tfo_active_disable_stamp, from Eric
Dumazet.
11) act_skbmod should only operate on ethernet packets, from Peilin Ye.
12) Fix slab out-of-bpunds in fib6_nh_flush_exceptions(),, from Psolo
Abeni.
13) Fix sparx5 dependencies, from Yajun Deng.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (74 commits)
dpaa2-switch: seed the buffer pool after allocating the swp
net: sched: cls_api: Fix the the wrong parameter
net: sparx5: fix unmet dependencies warning
net: dsa: tag_ksz: dont let the hardware process the layer 4 checksum
net: dsa: ensure linearized SKBs in case of tail taggers
ravb: Remove extra TAB
ravb: Fix a typo in comment
net: dsa: sja1105: make VID 4095 a bridge VLAN too
tcp: disable TFO blackhole logic by default
sctp: do not update transport pathmtu if SPP_PMTUD_ENABLE is not set
net: ixp46x: fix ptp build failure
ibmvnic: Remove the proper scrq flush
selftests: net: add ESP-in-UDP PMTU test
udp: check encap socket in __udp_lib_err
sctp: update active_key for asoc when old key is being replaced
r8169: Avoid duplicate sysfs entry creation error
ixgbe: Fix packet corruption due to missing DMA sync
Revert "qed: fix possible unpaired spin_{un}lock_bh in _qed_mcp_cmd_and_union()"
ipv6: fix another slab-out-of-bounds in fib6_nh_flush_exceptions
fsl/fman: Add fibre support
...
|
|
Any interraction with the buffer pool (seeding a buffer, acquire one) is
made through a software portal (SWP, a DPIO object).
There are circumstances where the dpaa2-switch driver probes on a DPSW
before any DPIO devices have been probed. In this case, seeding of the
buffer pool will lead to a panic since no SWPs are initialized.
To fix this, seed the buffer pool after making sure that the software
portals have been probed and are ready to be used.
Fixes: 0b1b71370458 ("staging: dpaa2-switch: handle Rx path on control interface")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
WARNING: unmet direct dependencies detected for PHY_SPARX5_SERDES
Depends on [n]: (ARCH_SPARX5 || COMPILE_TEST [=n]) && OF [=y] && HAS_IOMEM [=y]
Selected by [y]:
- SPARX5_SWITCH [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_MICROCHIP [=y] && NET_SWITCHDEV [=y] && HAS_IOMEM [=y] && OF [=y]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Align the member description comments for struct ravb_desc by
removing the extra TAB.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the typo RX->TX in comment, as the code following the comment
process TX and not RX.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This simple series of commands:
ip link add br0 type bridge vlan_filtering 1
ip link set swp0 master br0
fails on sja1105 with the following error:
[ 33.439103] sja1105 spi0.1: vlan-lookup-table needs to have at least the default untagged VLAN
[ 33.447710] sja1105 spi0.1: Invalid config, cannot upload
Warning: sja1105: Failed to change VLAN Ethertype.
For context, sja1105 has 3 operating modes:
- SJA1105_VLAN_UNAWARE: the dsa_8021q_vlans are committed to hardware
- SJA1105_VLAN_FILTERING_FULL: the bridge_vlans are committed to hardware
- SJA1105_VLAN_FILTERING_BEST_EFFORT: both the dsa_8021q_vlans and the
bridge_vlans are committed to hardware
Swapping out a VLAN list and another in happens in
sja1105_build_vlan_table(), which performs a delta update procedure.
That function is called from a few places, notably from
sja1105_vlan_filtering() which is called from the
SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING handler.
The above set of 2 commands fails when run on a kernel pre-commit
8841f6e63f2c ("net: dsa: sja1105: make devlink property
best_effort_vlan_filtering true by default"). So the priv->vlan_state
transition that takes place is between VLAN-unaware and full VLAN
filtering. So the dsa_8021q_vlans are swapped out and the bridge_vlans
are swapped in.
So why does it fail?
Well, the bridge driver, through nbp_vlan_init(), first sets up the
SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING attribute, and only then
proceeds to call nbp_vlan_add for the default_pvid.
So when we swap out the dsa_8021q_vlans and swap in the bridge_vlans in
the SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING handler, there are no bridge
VLANs (yet). So we have wiped the VLAN table clean, and the low-level
static config checker complains of an invalid configuration. We _will_
add the bridge VLANs using the dynamic config interface, albeit later,
when nbp_vlan_add() calls us. So it is natural that it fails.
So why did it ever work?
Surprisingly, it looks like I only tested this configuration with 2
things set up in a particular way:
- a network manager that brings all ports up
- a kernel with CONFIG_VLAN_8021Q=y
It is widely known that commit ad1afb003939 ("vlan_dev: VLAN 0 should be
treated as "no vlan tag" (802.1p packet)") installs VID 0 to every net
device that comes up. DSA treats these VLANs as bridge VLANs, and
therefore, in my testing, the list of bridge_vlans was never empty.
However, if CONFIG_VLAN_8021Q is not enabled, or the port is not up when
it joins a VLAN-aware bridge, the bridge_vlans list will be temporarily
empty, and the sja1105_static_config_reload() call from
sja1105_vlan_filtering() will fail.
To fix this, the simplest thing is to keep VID 4095, the one used for
CPU-injected control packets since commit ed040abca4c1 ("net: dsa:
sja1105: use 4095 as the private VLAN for untagged traffic"), in the
list of bridge VLANs too, not just the list of tag_8021q VLANs. This
ensures that the list of bridge VLANs will never be empty.
Fixes: ec5ae61076d0 ("net: dsa: sja1105: save/restore VLANs using a delta commit method")
Reported-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The rework of the ixp46x cpu detection left the network driver in
a half broken state:
drivers/net/ethernet/xscale/ptp_ixp46x.c: In function 'ptp_ixp_init':
drivers/net/ethernet/xscale/ptp_ixp46x.c:290:51: error: 'IXP4XX_TIMESYNC_BASE_VIRT' undeclared (first use in this function)
290 | (struct ixp46x_ts_regs __iomem *) IXP4XX_TIMESYNC_BASE_VIRT;
| ^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/xscale/ptp_ixp46x.c:290:51: note: each undeclared identifier is reported only once for each function it appears in
drivers/net/ethernet/xscale/ptp_ixp46x.c: At top level:
drivers/net/ethernet/xscale/ptp_ixp46x.c:323:1: error: data definition has no type or storage class [-Werror]
323 | module_init(ptp_ixp_init);
I have patches to complete the transition for a future release, but
for the moment, add the missing include statements to get it to build
again.
Fixes: 09aa9aabdcc4 ("soc: ixp4xx: move cpu detection to linux/soc/ixp4xx/cpu.h")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 65d6470d139a ("ibmvnic: clean pending indirect buffs during reset")
intended to remove the call to ibmvnic_tx_scrq_flush() when the
->resetting flag is true and was tested that way. But during the final
rebase to net-next, the hunk got applied to a block few lines below
(which happened to have the same diff context) and the wrong call to
ibmvnic_tx_scrq_flush() got removed.
Fix that by removing the correct ibmvnic_tx_scrq_flush() and restoring
the one that was incorrectly removed.
Fixes: 65d6470d139a ("ibmvnic: clean pending indirect buffs during reset")
Reported-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When registering the MDIO bus for a r8169 device, we use the PCI
bus/device specifier as a (seemingly) unique device identifier.
However the very same BDF number can be used on another PCI segment,
which makes the driver fail probing:
[ 27.544136] r8169 0002:07:00.0: enabling device (0000 -> 0003)
[ 27.559734] sysfs: cannot create duplicate filename '/class/mdio_bus/r8169-700'
....
[ 27.684858] libphy: mii_bus r8169-700 failed to register
[ 27.695602] r8169: probe of 0002:07:00.0 failed with error -22
Add the segment number to the device name to make it more unique.
This fixes operation on ARM N1SDP boards, with two boards connected
together to form an SMP system, and all on-board devices showing up
twice, just on different PCI segments. A similar issue would occur on
large systems with many PCI slots and multiple RTL8169 NICs.
Fixes: f1e911d5d0dfd ("r8169: add basic phylib support")
Signed-off-by: Sayanta Pattanayak <sayanta.pattanayak@arm.com>
[Andre: expand commit message, use pci_domain_nr()]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When receiving a packet with multiple fragments, hardware may still
touch the first fragment until the entire packet has been received. The
driver therefore keeps the first fragment mapped for DMA until end of
packet has been asserted, and delays its dma_sync call until then.
The driver tries to fit multiple receive buffers on one page. When using
3K receive buffers (e.g. using Jumbo frames and legacy-rx is turned
off/build_skb is being used) on an architecture with 4K pages, the
driver allocates an order 1 compound page and uses one page per receive
buffer. To determine the correct offset for a delayed DMA sync of the
first fragment of a multi-fragment packet, the driver then cannot just
use PAGE_MASK on the DMA address but has to construct a mask based on
the actual size of the backing page.
Using PAGE_MASK in the 3K RX buffer/4K page architecture configuration
will always sync the first page of a compound page. With the SWIOTLB
enabled this can lead to corrupted packets (zeroed out first fragment,
re-used garbage from another packet) and various consequences, such as
slow/stalling data transfers and connection resets. For example, testing
on a link with MTU exceeding 3058 bytes on a host with SWIOTLB enabled
(e.g. "iommu=soft swiotlb=262144,force") TCP transfers quickly fizzle
out without this patch.
Cc: stable@vger.kernel.org
Fixes: 0c5661ecc5dd7 ("ixgbe: fix crash in build_skb Rx code path")
Signed-off-by: Markus Boehme <markubo@amazon.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 6206b7981a36476f4695d661ae139f7db36a802d.
That patch added additional spin_{un}lock_bh(), which was harmless
but pointless. The orginal code path has guaranteed the pair of
spin_{un}lock_bh().
We'd better revert it before we find the exact root cause of the
bug_on mentioned in that patch.
Fixes: 6206b7981a36 ("qed: fix possible unpaired spin_{un}lock_bh in _qed_mcp_cmd_and_union()")
Cc: David S. Miller <davem@davemloft.net>
Cc: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Jia He <justin.he@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set SUPPORTED_FIBRE to mac_dev->if_support. It allows proper usage of
PHYs with optical/fiber support.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes my earlier patch which broke vlan unaware bridges.
The IVL bit now only gets set for vid's larger than 1.
Fixes: 11d8d98cbeef ("mt7530 fix mt7530_fdb_write vid missing ivl bit")
Signed-off-by: Eric Woudstra <ericwouds@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Subbaraya Sundeep says:
====================
octeontx2-af: Introduce DMAC based switching
With this patch set packets can be switched between
all CGX mapped PFs and VFs in the system based on
the DMAC addresses. To implement this:
AF allocates high priority rules from top entry(0) in MCAM.
Rules are allocated for all the CGX mapped PFs and VFs though
they are not active and with no NIXLFs attached.
Rules for a PF/VF will be enabled only after they are brought up.
Two rules one for TX and one for RX are allocated for each PF/VF.
A packet sent from a PF/VF with a destination mac of another
PF/VF will be hit by TX rule and sent to LBK channel 63. The
same returned packet will be hit by RX rule whose action is
to forward packet to PF/VF with that destination mac.
Implementation of this for 98xx is tricky since there are
two NIX blocks and till now a PF/VF can install rule for
an NIX0/1 interface only if it is mapped to corresponding NIX0/1 block.
Hence Tx rules are modified such that TX interface in MCAM
entry can be either NIX0-TX or NIX1-TX.
Testing:
1. Create two VFs over PF1(on NIX0) and assign two VFs to two VMs
2. Assign ip addresses to two VFs in VMs and PF2(on NIX1) in host.
3. Assign static arp entries in two VMs and PF2.
4. Ping between VMs and host PF2.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, VF doesn't enable rx VLAN offload when initializating,
and PF does it for VFs. If user disable the rx VLAN offload for
VF with ethtool -K, and reload the VF driver, it may cause the
rx VLAN offload state being inconsistent between hardware and
software.
Fixes it by enabling rx VLAN offload when VF initializing.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
control
For hardware limitation, port VLAN filter is port level, and
effective for all the functions of the port. So if not support
port VLAN bypass, it's necessary to disable the port VLAN filter,
in order to support function level VLAN filter control.
Fixes: 2ba306627f59 ("net: hns3: add support for modify VLAN filter state")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When VF need response from PF, VF will wait (1us - 1s) to receive
the response, or it will wait timeout and the VF action fails.
If VF do not receive response in 1st action because timeout,
the 2nd action may receive response for the 1st action, and get
incorrect response data.VF must reciveve the right response from
PF,or it will cause unexpected error.
This patch adds match_id to check mailbox response from PF to VF,
to make sure VF get the right response:
1. The message sent from VF was labelled with match_id which was a
unique 16-bit non-zero value.
2. The response sent from PF will label with match_id which got from
the request.
3. The VF uses the match_id to match request and response message.
This scheme depends on PF driver supports match_id, if PF driver doesn't
support then VF will uses the original scheme.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, the mailbox synchronous communication between VF and PF use
the following fields to maintain communication:
1. Origin_mbx_msg which was combined by message code and subcode, used
to match request and response.
2. Received_resp which means whether received response.
There may possible mismatches of the following situation:
1. VF sends message A with code=1 subcode=1.
2. PF was blocked about 500ms when processing the message A.
3. VF will detect message A timeout because it can't get the response
within 500ms.
4. VF sends message B with code=1 subcode=1 which equal message A.
5. PF processes the first message A and send the response message to
VF.
6. VF will identify the response matched the message B because the
code/subcode is the same. This will lead to mismatch of request and
response.
To fix the above bug, we use the following scheme:
1. The message sent from VF was labelled with match_id which was a
unique 16-bit non-zero value.
2. The response sent from PF will label with match_id which got from
the request.
3. The VF uses the match_id to match request and response message.
As for PF driver, it only needs to copy the match_id from request to
response.
Fixes: dde1a86e93ca ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As of now any communication between CGXs PFs and
their VFs within the system is possible only by
external switches sending packets back to the
system. This patch adds internal switching support.
Broadcast packet replication is not covered here.
RVU admin function (AF) maintains MAC addresses
of all interfaces in the system. When switching is
enabled, MCAM entries are allocated to install rules
such that packets with DMAC matching any of the
internal interface MAC addresses is punted back
into the system via the loopback channel.
On the receive side the default unicast rules
are modified to not check for ingress channel.
So any packet with matching DMAC irrespective of
which interface it is coming from will be forwarded
to the respective PF/VF interface.
The transmit side rules and default unicast rules
are updated if user changes MAC address of an interface.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
AF till now only manages the allocation and freeing of
MCAM rules for other PF/VFs in system. To implement
L2 switching between all CGX mapped PF and VFs, AF
requires MCAM entries for DMAC rules for each PF and VF.
This patch modifies AF driver such that AF can also
allocate MCAM rules and install rules for other
PFs and VFs. All the checks like channel verification
for RX rules and PF_FUNC verification for TX rules are
relaxed in case AF is allocating or installing rules.
Also all the entry and counter to owner mappings are
set to NPC_MCAM_INVALID_MAP when they are free indicating
those are not allocated to AF nor PF/VFs.
This patch also ensures that AF allocated and installed
entries are displayed in debugfs.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For enabling VF-VF switching the packets egressing
out of CGX mapped VFs needed to be sent to LBK
so that same packets are received back to the system.
But the LBK link also needs to be enabled in addition
to a VF's mapped CGX_LMAC link otherwise hardware
raises send error interrupt indicating selected LBK
link is not enabled in NIX_AF_TL3_TL2X_LINKX_CFG register.
Hence this patch enables all LBK links in
TL3_TL2_LINKX_CFG registers.
Also to enable packet flow between PFs/VFs of NIX0
to PFs/VFs of NIX1(in 98xx silicon) the NPC TX DMAC
rules has to be installed such that rules must be hit
for any TX interface i.e., NIX0-TX or NIX1-TX provided
DMAC match creteria is met. Hence this patch changes the
behavior such that MCAM is programmed to match with any
NIX0/1-TX interface for TX rules.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Building on ARCH=arc causes a "redefined" warning, so rename this
driver's CACHE_LINE_MASK to avoid the warning.
../drivers/net/ethernet/hisilicon/hip04_eth.c:134: warning: "CACHE_LINE_MASK" redefined
134 | #define CACHE_LINE_MASK 0x3F
In file included from ../include/linux/cache.h:6,
from ../include/linux/printk.h:9,
from ../include/linux/kernel.h:19,
from ../include/linux/list.h:9,
from ../include/linux/module.h:12,
from ../drivers/net/ethernet/hisilicon/hip04_eth.c:7:
../arch/arc/include/asm/cache.h:17: note: this is the location of the previous definition
17 | #define CACHE_LINE_MASK (~(L1_CACHE_BYTES - 1))
Fixes: d413779cdd93 ("net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current PTP initialization logic does not account for firmware
reset that may cause PTP capability to change. The valid pointer
bp->ptp_cfg is used to indicate that the device is capable of PTP
and that it has been initialized. So we must clean up bp->ptp_cfg
and free it if the firmware after reset does not support PTP.
Fixes: 93cb62d98e9c ("bnxt_en: Enable hardware PTP support")
Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device needs to be in ifup state for PTP to function, so move
bnxt_ptp_init() to bnxt_open(). This means that the PHC will be
registered during bnxt_open().
This also makes firmware reset work correctly. PTP configurations
may change after firmware upgrade or downgrade. bnxt_open() will
be called after firmware reset, so it will work properly.
bnxt_ptp_start() is now incorporated into bnxt_ptp_init(). We now
also need to call bnxt_ptp_clear() in bnxt_close().
Fixes: 93cb62d98e9c ("bnxt_en: Enable hardware PTP support")
Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bnxt_half_open_nic() is called during during ethtool self test and is
protected by rtnl_lock. Firmware reset can be happening at the same
time. Only critical portions of the entire firmware reset sequence
are protected by the rtnl_lock. It is possible that bnxt_half_open_nic()
can be called when the firmware reset sequence is aborting. In that
case, bnxt_half_open_nic() needs to check if the ABORT_ERR flag is set
and abort if it is. The ethtool self test will fail but the NIC will be
brought to a consistent IF_DOWN state.
Without this patch, if bnxt_half_open_nic() were to continue in this
error state, it may crash like this:
bnxt_en 0000:82:00.1 enp130s0f1np1: FW reset in progress during close, FW reset will be aborted
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
...
Process ethtool (pid: 333327, stack limit = 0x0000000046476577)
Call trace:
bnxt_alloc_mem+0x444/0xef0 [bnxt_en]
bnxt_half_open_nic+0x24/0xb8 [bnxt_en]
bnxt_self_test+0x2dc/0x390 [bnxt_en]
ethtool_self_test+0xe0/0x1f8
dev_ethtool+0x1744/0x22d0
dev_ioctl+0x190/0x3e0
sock_ioctl+0x238/0x480
do_vfs_ioctl+0xc4/0x758
ksys_ioctl+0x84/0xb8
__arm64_sys_ioctl+0x28/0x38
el0_svc_handler+0xb0/0x180
el0_svc+0x8/0xc
Fixes: a1301f08c5ac ("bnxt_en: Check abort error state in bnxt_open_nic().")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only pass supported VLAN protocol IDs for stripped VLAN tags to the
stack. The stack will hit WARN() if the protocol ID is unsupported.
Existing firmware sets up the chip to strip 0x8100, 0x88a8, 0x9100.
Only the 1st two protocols are supported by the kernel.
Fixes: a196e96bb68f ("bnxt_en: clean up VLAN feature bit handling")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When bnxt_open() fails in the firmware reset path, the driver needs to
gracefully abort, but it is executing code that should be invoked only
in the success path. Define a function to abort FW reset and
consolidate all error paths to call this new function.
Fixes: dab62e7c2de7 ("bnxt_en: Implement faster recovery for firmware fatal error.")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the BNXT_FW_RESET_STATE_POLL_VF state in bnxt_fw_reset_task() after all
VFs have unregistered, we need to check for BNXT_STATE_ABORT_ERR after
we acquire the rtnl_lock. If the flag is set, we need to abort.
Fixes: 230d1f0de754 ("bnxt_en: Handle firmware reset.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The capabilities can change after firmware upgrade/downgrade, so we
should get the up-to-date RoCE capabilities everytime bnxt_ulp_probe()
is called.
Fixes: 2151fe0830fd ("bnxt_en: Handle RESET_NOTIFY async event from firmware.")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ETS proportions are presented to HWRM_QUEUE_COS2BW_CFG as minimum
bandwidth constraints. Thus, zero is a legal value for a given TC.
However, if all the other TCs sum up to 100%, then at least one
hardware queue will starve, resulting in guaranteed TX timeouts.
Reject such nonsensical configurations.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If device is already disabled in reset path and PCI io error is
detected before the device could be enabled, driver could
call pci_disable_device() for already disabled device. Fix this
problem by calling pci_disable_device() only if the device is already
enabled.
Fixes: 6316ea6db93d ("bnxt_en: Enable AER support.")
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit 9a5605505d9c (" bonding: Add struct bond_ipesc to manage SA") is causing
following build error when XFRM is not selected in kernel config.
lld: error: undefined symbol: xfrm_dev_state_flush
>>> referenced by bond_main.c:3453 (drivers/net/bonding/bond_main.c:3453)
>>> net/bonding/bond_main.o:(bond_netdev_event) in archive drivers/built-in.a
Fixes: 9a5605505d9c (" bonding: Add struct bond_ipesc to manage SA")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: Taehee Yoo <ap420073@gmail.com>
CC: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to reference guides mt7530 (mt7620) and mt7531:
NOTE: When IVL is reset, MAC[47:0] and FID[2:0] will be used to
read/write the address table. When IVL is set, MAC[47:0] and CVID[11:0]
will be used to read/write the address table.
Since the function only fills in CVID and no FID, we need to set the
IVL bit. The existing code does not set it.
This is a fix for the issue I dropped here earlier:
http://lists.infradead.org/pipermail/linux-mediatek/2021-June/025697.html
With this patch, it is now possible to delete the 'self' fdb entry
manually. However, wifi roaming still has the same issue, the entry
does not get deleted automatically. Wifi roaming also needs a fix
somewhere else to function correctly in combination with vlan.
Signed-off-by: Eric Woudstra <ericwouds@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull fallthrough fixes from Gustavo Silva:
"This fixes many fall-through warnings when building with Clang and
-Wimplicit-fallthrough, and also enables -Wimplicit-fallthrough for
Clang, globally.
It's also important to notice that since we have adopted the use of
the pseudo-keyword macro fallthrough, we also want to avoid having
more /* fall through */ comments being introduced. Contrary to GCC,
Clang doesn't recognize any comments as implicit fall-through markings
when the -Wimplicit-fallthrough option is enabled.
So, in order to avoid having more comments being introduced, we use
the option -Wimplicit-fallthrough=5 for GCC, which similar to Clang,
will cause a warning in case a code comment is intended to be used as
a fall-through marking. The patch for Makefile also enforces this.
We had almost 4,000 of these issues for Clang in the beginning, and
there might be a couple more out there when building some
architectures with certain configurations. However, with the recent
fixes I think we are in good shape and it is now possible to enable
the warning for Clang"
* tag 'Wimplicit-fallthrough-clang-5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux: (27 commits)
Makefile: Enable -Wimplicit-fallthrough for Clang
powerpc/smp: Fix fall-through warning for Clang
dmaengine: mpc512x: Fix fall-through warning for Clang
usb: gadget: fsl_qe_udc: Fix fall-through warning for Clang
powerpc/powernv: Fix fall-through warning for Clang
MIPS: Fix unreachable code issue
MIPS: Fix fall-through warnings for Clang
ASoC: Mediatek: MT8183: Fix fall-through warning for Clang
power: supply: Fix fall-through warnings for Clang
dmaengine: ti: k3-udma: Fix fall-through warning for Clang
s390: Fix fall-through warnings for Clang
dmaengine: ipu: Fix fall-through warning for Clang
iommu/arm-smmu-v3: Fix fall-through warning for Clang
mmc: jz4740: Fix fall-through warning for Clang
PCI: Fix fall-through warning for Clang
scsi: libsas: Fix fall-through warning for Clang
video: fbdev: Fix fall-through warning for Clang
math-emu: Fix fall-through warning
cpufreq: Fix fall-through warning for Clang
drm/msm: Fix fall-through warning in msm_gem_new_impl()
...
|
|
The current error handling code of hso_create_net_device is
hso_free_net_device, no matter which errors lead to. For example,
WARNING in hso_free_net_device [1].
Fix this by refactoring the error handling code of
hso_create_net_device by handling different errors by different code.
[1] https://syzkaller.appspot.com/bug?id=66eff8d49af1b28370ad342787413e35bbe76efe
Reported-by: syzbot+44d53c7255bb1aea22d2@syzkaller.appspotmail.com
Fixes: 5fcfb6d0bfcd ("hso: fix bailout in error case of probe")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Liajian reported a bug_on hit on a ThunderX2 arm64 server with FastLinQ
QL41000 ethernet controller:
BUG: scheduling while atomic: kworker/0:4/531/0x00000200
[qed_probe:488()]hw prepare failed
kernel BUG at mm/vmalloc.c:2355!
Internal error: Oops - BUG: 0 [#1] SMP
CPU: 0 PID: 531 Comm: kworker/0:4 Tainted: G W 5.4.0-77-generic #86-Ubuntu
pstate: 00400009 (nzcv daif +PAN -UAO)
Call trace:
vunmap+0x4c/0x50
iounmap+0x48/0x58
qed_free_pci+0x60/0x80 [qed]
qed_probe+0x35c/0x688 [qed]
__qede_probe+0x88/0x5c8 [qede]
qede_probe+0x60/0xe0 [qede]
local_pci_probe+0x48/0xa0
work_for_cpu_fn+0x24/0x38
process_one_work+0x1d0/0x468
worker_thread+0x238/0x4e0
kthread+0xf0/0x118
ret_from_fork+0x10/0x18
In this case, qed_hw_prepare() returns error due to hw/fw error, but in
theory work queue should be in process context instead of interrupt.
The root cause might be the unpaired spin_{un}lock_bh() in
_qed_mcp_cmd_and_union(), which causes botton half is disabled incorrectly.
Reported-by: Lijian Zhang <Lijian.Zhang@arm.com>
Signed-off-by: Jia He <justin.he@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Shifting the u16 integer oct->pcie_port by CN23XX_PKT_INPUT_CTL_MAC_NUM_POS
(29) bits will be promoted to a 32 bit signed int and then sign-extended
to a u64. In the cases where oct->pcie_port where bit 2 is set (e.g. 3..7)
the shifted value will be sign extended and the top 32 bits of the result
will be set.
Fix this by casting the u16 values to a u64 before the 29 bit left shift.
Addresses-Coverity: ("Unintended sign extension")
Fixes: 3451b97cce2d ("liquidio: CN23XX register setup")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Making global2 support mandatory removed the Kconfig symbol
NET_DSA_MV88E6XXX_GLOBAL2. This symbol also served as an intermediate
symbol to make NET_DSA_MV88E6XXX_PTP depend on NET_DSA_MV88E6XXX. With
the symbol removed, the user is always asked about PTP support for
Marvell 88E6xxx switches, even if the latter support is not enabled.
Fix this by reinstating the dependency.
Fixes: 63368a7416df144b ("net: dsa: mv88e6xxx: Make global2 support mandatory")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
r8152 driver sets up the MAC address at reset-resume, while
rtl8152_set_mac_address() has the temporary autopm get/put. This may
lead to a deadlock as the PM lock has been already taken for the
execution of the runtime PM callback.
This patch adds the workaround to avoid the superfluous autpm when
called from rtl8152_reset_resume().
Link: https://bugzilla.suse.com/show_bug.cgi?id=1186194
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rtl8152_close() takes the refcount via usb_autopm_get_interface() but
it doesn't release when RTL8152_UNPLUG test hits. This may lead to
the imbalance of PM refcount. This patch addresses it.
Link: https://bugzilla.suse.com/show_bug.cgi?id=1186194
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski.
"Including fixes from bpf and netfilter.
Current release - regressions:
- sock: fix parameter order in sock_setsockopt()
Current release - new code bugs:
- netfilter: nft_last:
- fix incorrect arithmetic when restoring last used
- honor NFTA_LAST_SET on restoration
Previous releases - regressions:
- udp: properly flush normal packet at GRO time
- sfc: ensure correct number of XDP queues; don't allow enabling the
feature if there isn't sufficient resources to Tx from any CPU
- dsa: sja1105: fix address learning getting disabled on the CPU port
- mptcp: addresses a rmem accounting issue that could keep packets in
subflow receive buffers longer than necessary, delaying MPTCP-level
ACKs
- ip_tunnel: fix mtu calculation for ETHER tunnel devices
- do not reuse skbs allocated from skbuff_fclone_cache in the napi
skb cache, we'd try to return them to the wrong slab cache
- tcp: consistently disable header prediction for mptcp
Previous releases - always broken:
- bpf: fix subprog poke descriptor tracking use-after-free
- ipv6:
- allocate enough headroom in ip6_finish_output2() in case
iptables TEE is used
- tcp: drop silly ICMPv6 packet too big messages to avoid
expensive and pointless lookups (which may serve as a DDOS
vector)
- make sure fwmark is copied in SYNACK packets
- fix 'disable_policy' for forwarded packets (align with IPv4)
- netfilter: conntrack:
- do not renew entry stuck in tcp SYN_SENT state
- do not mark RST in the reply direction coming after SYN packet
for an out-of-sync entry
- mptcp: cleanly handle error conditions with MP_JOIN and syncookies
- mptcp: fix double free when rejecting a join due to port mismatch
- validate lwtstate->data before returning from skb_tunnel_info()
- tcp: call sk_wmem_schedule before sk_mem_charge in zerocopy path
- mt76: mt7921: continue to probe driver when fw already downloaded
- bonding: fix multiple issues with offloading IPsec to (thru?) bond
- stmmac: ptp: fix issues around Qbv support and setting time back
- bcmgenet: always clear wake-up based on energy detection
Misc:
- sctp: move 198 addresses from unusable to private scope
- ptp: support virtual clocks and timestamping
- openvswitch: optimize operation for key comparison"
* tag 'net-5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (158 commits)
net: dsa: properly check for the bridge_leave methods in dsa_switch_bridge_leave()
sfc: add logs explaining XDP_TX/REDIRECT is not available
sfc: ensure correct number of XDP queues
sfc: fix lack of XDP TX queues - error XDP TX failed (-22)
net: fddi: fix UAF in fza_probe
net: dsa: sja1105: fix address learning getting disabled on the CPU port
net: ocelot: fix switchdev objects synced for wrong netdev with LAG offload
net: Use nlmsg_unicast() instead of netlink_unicast()
octeontx2-pf: Fix uninitialized boolean variable pps
ipv6: allocate enough headroom in ip6_finish_output2()
net: hdlc: rename 'mod_init' & 'mod_exit' functions to be module-specific
net: bridge: multicast: fix MRD advertisement router port marking race
net: bridge: multicast: fix PIM hello router port marking race
net: phy: marvell10g: fix differentiation of 88X3310 from 88X3340
dsa: fix for_each_child.cocci warnings
virtio_net: check virtqueue_add_sgs() return value
mptcp: properly account bulk freed memory
selftests: mptcp: fix case multiple subflows limited by server
mptcp: avoid processing packet if a subflow reset
mptcp: fix syncookie process if mptcp can not_accept new subflow
...
|
|
If it's not possible to allocate enough channels for XDP, XDP_TX and
XDP_REDIRECT don't work. However, only a message saying that not enough
channels were available was shown, but not saying what are the
consequences in that case. The user didn't know if he/she can use XDP
or not, if the performance is reduced, or what.
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 99ba0ea616aa ("sfc: adjust efx->xdp_tx_queue_count with the real
number of initialized queues") intended to fix a problem caused by a
round up when calculating the number of XDP channels and queues.
However, this was not the real problem. The real problem was that the
number of XDP TX queues had been reduced to half in
commit e26ca4b53582 ("sfc: reduce the number of requested xdp ev queues"),
but the variable xdp_tx_queue_count had remained the same.
Once the correct number of XDP TX queues is created again in the
previous patch of this series, this also can be reverted since the error
doesn't actually exist.
Only in the case that there is a bug in the code we can have different
values in xdp_queue_number and efx->xdp_tx_queue_count. Because of this,
and per Edward Cree's suggestion, I add instead a WARN_ON to catch if it
happens again in the future.
Note that the number of allocated queues can be higher than the number
of used ones due to the round up, as explained in the existing comment
in the code. That's why we also have to stop increasing xdp_queue_number
beyond efx->xdp_tx_queue_count.
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes: e26ca4b53582 sfc: reduce the number of requested xdp ev queues
The buggy commit intended to allocate less channels for XDP in order to
be more unlikely to reach the limit of 32 channels of the driver.
The idea was to use each IRQ/eventqeue for more XDP TX queues than
before, calculating which is the maximum number of TX queues that one
event queue can handle. For example, in EF10 each event queue could
handle up to 8 queues, better than the 4 they were handling before the
change. This way, it would have to allocate half of channels than before
for XDP TX.
The problem is that the TX queues are also contained inside the channel
structs, and there are only 4 queues per channel. Reducing the number of
channels means also reducing the number of queues, resulting in not
having the desired number of 1 queue per CPU.
This leads to getting errors on XDP_TX and XDP_REDIRECT if they're
executed from a high numbered CPU, because there only exist queues for
the low half of CPUs, actually. If XDP_TX/REDIRECT is executed in a low
numbered CPU, the error doesn't happen. This is the error in the logs
(repeated many times, even rate limited):
sfc 0000:5e:00.0 ens3f0np0: XDP TX failed (-22)
This errors happens in function efx_xdp_tx_buffers, where it expects to
have a dedicated XDP TX queue per CPU.
Reverting the change makes again more likely to reach the limit of 32
channels in machines with many CPUs. If this happen, no XDP_TX/REDIRECT
will be possible at all, and we will have this log error messages:
At interface probe:
sfc 0000:5e:00.0: Insufficient resources for 12 XDP event queues (24 other channels, max 32)
At every subsequent XDP_TX/REDIRECT failure, rate limited:
sfc 0000:5e:00.0 ens3f0np0: XDP TX failed (-22)
However, without reverting the change, it makes the user to think that
everything is OK at probe time, but later it fails in an unpredictable
way, depending on the CPU that handles the packet.
It is better to restore the predictable behaviour. If the user sees the
error message at probe time, he/she can try to configure the best way it
fits his/her needs. At least, he/she will have 2 options:
- Accept that XDP_TX/REDIRECT is not available (he/she may not need it)
- Load sfc module with modparam 'rss_cpus' with a lower number, thus
creating less normal RX queues/channels, letting more free resources
for XDP, with some performance penalty.
Anyway, let the calculation of maximum TX queues that can be handled by
a single event queue, and use it only if it's less than the number of TX
queues per channel. This doesn't happen in practice, but could happen if
some constant values are tweaked in the future, such us
EFX_MAX_TXQ_PER_CHANNEL, EFX_MAX_EVQ_SIZE or EFX_MAX_DMAQ_SIZE.
Related mailing list thread:
https://lore.kernel.org/bpf/20201215104327.2be76156@carbon/
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fp is netdev private data and it cannot be
used after free_netdev() call. Using fp after free_netdev()
can cause UAF bug. Fix it by moving free_netdev() after error message.
Fixes: 61414f5ec983 ("FDDI: defza: Add support for DEC FDDIcontroller 700
TURBOchannel adapter")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In May 2019 when commit 640f763f98c2 ("net: dsa: sja1105: Add support
for Spanning Tree Protocol") was introduced, the comment that "STP does
not get called for the CPU port" was true. This changed after commit
0394a63acfe2 ("net: dsa: enable and disable all ports") in August 2019
and went largely unnoticed, because the sja1105_bridge_stp_state_set()
method did nothing different compared to the static setup done by
sja1105_init_mac_settings().
With the ability to turn address learning off introduced by the blamed
commit, there is a new priv->learn_ena port mask in the driver. When
sja1105_bridge_stp_state_set() gets called and we are in
BR_STATE_LEARNING or later, address learning is enabled or not depending
on priv->learn_ena & BIT(port).
So what happens is that priv->learn_ena is not being set from anywhere
for the CPU port, and the static configuration done by
sja1105_init_mac_settings() is being overwritten.
To solve this, acknowledge that the static configuration of STP state is
no longer necessary because the STP state is being set by the DSA core
now, but what is necessary is to set priv->learn_ena for the CPU port.
Fixes: 4d9423549501 ("net: dsa: sja1105: offload bridge port flags to device")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The point with a *dev and a *brport_dev is that when we have a LAG net
device that is a bridge port, *dev is an ocelot net device and
*brport_dev is the bonding/team net device. The ocelot net device
beneath the LAG does not exist from the bridge's perspective, so we need
to sync the switchdev objects belonging to the brport_dev and not to the
dev.
Fixes: e4bd44e89dcf ("net: ocelot: replay switchdev events when joining bridge")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the case where act->id is FLOW_ACTION_POLICE and also
act->police.rate_bytes_ps > 0 or act->police.rate_pkt_ps is not > 0
the boolean variable pps contains an uninitialized value when
function otx2_tc_act_set_police is called. Fix this by initializing
pps to false.
Addresses-Coverity: ("Uninitialized scalar variable)"
Fixes: 68fbff68dbea ("octeontx2-pf: Add police action for TC flower")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename module_init & module_exit functions that are named
"mod_init" and "mod_exit" so that they are unique in both the
System.map file and in initcall_debug output instead of showing
up as almost anonymous "mod_init".
This is helpful for debugging and in determining how long certain
module_init calls take to execute.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: netdev@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Martin Schiller <ms@dev.tdt.de>
Cc: linux-x25@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation to enable -Wimplicit-fallthrough for Clang, fix the
following warning by explicitly adding a break statement:
drivers/net/ethernet/netronome/nfp/flower/conntrack.c:1175:2: warning: unannotated fall-through between switch labels [-Wimplicit-fallthrough]
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
