| Age | Commit message (Collapse) | Author |
|---|
|
Register a struct led_classdev with the kernel's LED subsystem and
create a throughput-based trigger for it. Then mac80211 makes the LED
blink.
Tested with Tenda U12 (RTL8812AU), Tenda U9 (RTL8811CU), TP-Link Archer
T2U Nano (RTL8811AU), TP-Link Archer T3U Plus (RTL8812BU), Edimax
EW-7611UCB (RTL8821AU), LM842 (RTL8822CU).
Also tested with devices which don't have LEDs: the laptop's internal
RTL8822CE and a no-name RTL8723DU.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/6c43451f-ab2f-4e76-ac6e-ff5a18dd981d@gmail.com
|
|
This is the equivalent of commit 28818b4d871b ("wifi: rtw88: usb: Fix
disconnection after beacon loss") for SDIO chips.
Tested on Pinephone (RTL8723CS), random disconnections became rare,
instead of a frequent nuisance.
Cc: stable@vger.kernel.org
Signed-off-by: Fiona Klute <fiona.klute@gmx.de>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com> # Tested on Pinebook
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250106135434.35936-1-fiona.klute@gmx.de
|
|
Fix 3 typos in 8703b driver. 2 typos in calibration routines are not
fatal and do not seem to have any impact, just fix them to match vendor
driver.
However the last one in rtw8703b_set_channel_bb() clears too many bits
in REG_OFDM0_TX_PSD_NOISE, causing TX and RX issues (neither rate goes
above MCS0-MCS1). Vendor driver clears only 2 most significant bits.
With the last typo fixed, the driver is able to reach MCS7 on Pinebook
Cc: stable@vger.kernel.org
Fixes: 9bb762b3a957 ("wifi: rtw88: Add definitions for 8703b chip")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Fiona Klute <fiona.klute@gmx.de>
Tested-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250103075107.1337533-1-anarsoul@gmail.com
|
|
It's not used for anything.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/b80f7904-c6b4-4d12-a5f9-69ab9b965732@gmail.com
|
|
Add some extra configuration for USB devices. Currently only RTL8822BU
version (cut) D needs this. The new code makes use of the existing
usb3_param_8822b array from rtw8822b.c.
A user reported that TP-Link Archer T3U in USB 3 mode was randomly
disconnecting from USB:
[ 26.036502] usb 2-2: new SuperSpeed USB device number 3 using xhci_hcd
...
[ 27.576491] usb 2-2: USB disconnect, device number 3
[ 28.621528] usb 2-2: new SuperSpeed USB device number 4 using xhci_hcd
...
[ 45.984521] usb 2-2: USB disconnect, device number 4
...
[ 46.845585] usb 2-2: new SuperSpeed USB device number 5 using xhci_hcd
...
[ 94.400380] usb 2-2: USB disconnect, device number 5
...
[ 95.590421] usb 2-2: new SuperSpeed USB device number 6 using xhci_hcd
This patch fixes that.
Link: https://github.com/lwfinger/rtw88/issues/262
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/9d312b14-0146-4be8-9c50-ef432234db50@gmail.com
|
|
RTL8922AE-VS is a variant of RTL8922AE, which is supported by firmware
version after 0.35.54.0 and only can support up to MCS11. Add a variant
struct to describe these requirements accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250108020955.14668-3-pkshih@realtek.com
|
|
Firmware after version 0.35.51.0 defines and exports more hardware
capabilities, which driver will consider reported QAM field as
EHT MCS capability to register hardware.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250108020955.14668-2-pkshih@realtek.com
|
|
The rtwdev->scanning flag isn't protected by mutex originally, so
cancel_hw_scan can pass the condition, but suddenly hw_scan completion
unset the flag and calls ieee80211_scan_completed() that will free
local->hw_scan_req. Then, cancel_hw_scan raises null-ptr-deref and
use-after-free. Fix it by moving the check condition to where
protected by mutex.
KASAN: null-ptr-deref in range [0x0000000000000088-0x000000000000008f]
CPU: 2 PID: 6922 Comm: kworker/2:2 Tainted: G OE
Hardware name: LENOVO 2356AD1/2356AD1, BIOS G7ETB6WW (2.76 ) 09/10/2019
Workqueue: events cfg80211_conn_work [cfg80211]
RIP: 0010:rtw89_fw_h2c_scan_offload_be+0xc33/0x13c3 [rtw89_core]
Code: 00 45 89 6c 24 1c 0f 85 23 01 00 00 48 8b 85 20 ff ff ff 48 8d
RSP: 0018:ffff88811fd9f068 EFLAGS: 00010206
RAX: dffffc0000000000 RBX: ffff88811fd9f258 RCX: 0000000000000001
RDX: 0000000000000011 RSI: 0000000000000001 RDI: 0000000000000089
RBP: ffff88811fd9f170 R08: 0000000000000000 R09: 0000000000000000
R10: ffff88811fd9f108 R11: 0000000000000000 R12: ffff88810e47f960
R13: 0000000000000000 R14: 000000000000ffff R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff8881d6f00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007531dfca55b0 CR3: 00000001be296004 CR4: 00000000001706e0
Call Trace:
<TASK>
? show_regs+0x61/0x73
? __die_body+0x20/0x73
? die_addr+0x4f/0x7b
? exc_general_protection+0x191/0x1db
? asm_exc_general_protection+0x27/0x30
? rtw89_fw_h2c_scan_offload_be+0xc33/0x13c3 [rtw89_core]
? rtw89_fw_h2c_scan_offload_be+0x458/0x13c3 [rtw89_core]
? __pfx_rtw89_fw_h2c_scan_offload_be+0x10/0x10 [rtw89_core]
? do_raw_spin_lock+0x75/0xdb
? __pfx_do_raw_spin_lock+0x10/0x10
rtw89_hw_scan_offload+0xb5e/0xbf7 [rtw89_core]
? _raw_spin_unlock+0xe/0x24
? __mutex_lock.constprop.0+0x40c/0x471
? __pfx_rtw89_hw_scan_offload+0x10/0x10 [rtw89_core]
? __mutex_lock_slowpath+0x13/0x1f
? mutex_lock+0xa2/0xdc
? __pfx_mutex_lock+0x10/0x10
rtw89_hw_scan_abort+0x58/0xb7 [rtw89_core]
rtw89_ops_cancel_hw_scan+0x120/0x13b [rtw89_core]
ieee80211_scan_cancel+0x468/0x4d0 [mac80211]
ieee80211_prep_connection+0x858/0x899 [mac80211]
ieee80211_mgd_auth+0xbea/0xdde [mac80211]
? __pfx_ieee80211_mgd_auth+0x10/0x10 [mac80211]
? cfg80211_find_elem+0x15/0x29 [cfg80211]
? is_bss+0x1b7/0x1d7 [cfg80211]
ieee80211_auth+0x18/0x27 [mac80211]
cfg80211_mlme_auth+0x3bb/0x3e7 [cfg80211]
cfg80211_conn_do_work+0x410/0xb81 [cfg80211]
? __pfx_cfg80211_conn_do_work+0x10/0x10 [cfg80211]
? __kasan_check_read+0x11/0x1f
? psi_group_change+0x8bc/0x944
? __kasan_check_write+0x14/0x22
? mutex_lock+0x8e/0xdc
? __pfx_mutex_lock+0x10/0x10
? __pfx___radix_tree_lookup+0x10/0x10
cfg80211_conn_work+0x245/0x34d [cfg80211]
? __pfx_cfg80211_conn_work+0x10/0x10 [cfg80211]
? update_cfs_rq_load_avg+0x3bc/0x3d7
? sched_clock_noinstr+0x9/0x1a
? sched_clock+0x10/0x24
? sched_clock_cpu+0x7e/0x42e
? newidle_balance+0x796/0x937
? __pfx_sched_clock_cpu+0x10/0x10
? __pfx_newidle_balance+0x10/0x10
? __kasan_check_read+0x11/0x1f
? psi_group_change+0x8bc/0x944
? _raw_spin_unlock+0xe/0x24
? raw_spin_rq_unlock+0x47/0x54
? raw_spin_rq_unlock_irq+0x9/0x1f
? finish_task_switch.isra.0+0x347/0x586
? __schedule+0x27bf/0x2892
? mutex_unlock+0x80/0xd0
? do_raw_spin_lock+0x75/0xdb
? __pfx___schedule+0x10/0x10
process_scheduled_works+0x58c/0x821
worker_thread+0x4c7/0x586
? __kasan_check_read+0x11/0x1f
kthread+0x285/0x294
? __pfx_worker_thread+0x10/0x10
? __pfx_kthread+0x10/0x10
ret_from_fork+0x29/0x6f
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
Fixes: 895907779752 ("rtw89: 8852a: add ieee80211_ops::hw_scan")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250107114254.6769-1-pkshih@realtek.com
|
|
For each MCC role, time limits, including max_tob_us, max_toa_us, and
mac_dur_us, are calculated if there are NoA attributes. The relation
between these time limits is "max_dur_us = max_tob_us + max_toa_us".
Then, the unit is converted from us to TU. However, originally, each
time limit was divided by 1024 independently. It missed to consider
the cases that max_tob_us or max_toa_us is not divisible by 1024. It
causes the result breaks "max_dur (TU) = max_tob (TU) + max_toa (TU)".
Finally, when MCC calculates pattern parameters based on these kinds
of time limits, it might not perform well.
Fixes: b09df09b55fb ("wifi: rtw89: mcc: initialize start flow")
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250103074412.124066-1-pkshih@realtek.com
|
|
For early chips, the RX BD info contains FS/LS bits for first/last segments
of a receiving packet. For 8922AE, the FS bit should be ignored, or it
may throw warning:
rtw89_8922ae 0000:1a:00.0: skb should not be ready before first segment start
To have compatible logic, FS determined by what pending skb is existing
(!new) or not.
Since we expect every single receiving packet in single one segment,
enlarge 4 bytes for RX BD info, and add a debug message to note if
RX buffer is possibly smaller than expected size.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250103025126.15378-1-pkshih@realtek.com
|
|
If WoWLAN failed in resume flow, the rtw89_ops_add_interface() triggered
without removing the interface first. Then the mgnt_entry list init again,
causing the list_empty() check in rtw89_chanctx_ops_assign_vif()
useless, and list_add_tail() again. Therefore, we have added a check to
prevent double adding of the list.
rtw89_8852ce 0000:01:00.0: failed to check wow status disabled
rtw89_8852ce 0000:01:00.0: wow: failed to check disable fw ready
rtw89_8852ce 0000:01:00.0: wow: failed to swap to normal fw
rtw89_8852ce 0000:01:00.0: failed to disable wow
rtw89_8852ce 0000:01:00.0: failed to resume for wow -110
rtw89_8852ce 0000:01:00.0: MAC has already powered on
i2c_hid_acpi i2c-ILTK0001:00: PM: acpi_subsys_resume+0x0/0x60 returned 0 after 284705 usecs
list_add corruption. prev->next should be next (ffff9d9719d82228), but was ffff9d9719f96030. (prev=ffff9d9719f96030).
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:34!
invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
CPU: 2 PID: 6918 Comm: kworker/u8:19 Tainted: G U O
Hardware name: Google Anraggar/Anraggar, BIOS Google_Anraggar.15217.514.0 03/25/2024
Workqueue: events_unbound async_run_entry_fn
RIP: 0010:__list_add_valid_or_report+0x9f/0xb0
Code: e8 56 89 ff ff 0f 0b 48 c7 c7 3e fc e0 96 48 89 c6 e8 45 89 ff ...
RSP: 0018:ffffa51b42bbbaf0 EFLAGS: 00010246
RAX: 0000000000000075 RBX: ffff9d9719d82ab0 RCX: 13acb86e047a4400
RDX: 3fffffffffffffff RSI: 0000000000000000 RDI: 00000000ffffdfff
RBP: ffffa51b42bbbb28 R08: ffffffff9768e250 R09: 0000000000001fff
R10: ffffffff9765e250 R11: 0000000000005ffd R12: ffff9d9719f95c40
R13: ffff9d9719f95be8 R14: ffff9d97081bfd78 R15: ffff9d9719d82060
FS: 0000000000000000(0000) GS:ffff9d9a6fb00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007e7d029a4060 CR3: 0000000345e38000 CR4: 0000000000750ee0
PKRU: 55555554
Call Trace:
<TASK>
? __die_body+0x68/0xb0
? die+0xaa/0xd0
? do_trap+0x9f/0x170
? __list_add_valid_or_report+0x9f/0xb0
? __list_add_valid_or_report+0x9f/0xb0
? handle_invalid_op+0x69/0x90
? __list_add_valid_or_report+0x9f/0xb0
? exc_invalid_op+0x3c/0x50
? asm_exc_invalid_op+0x16/0x20
? __list_add_valid_or_report+0x9f/0xb0
rtw89_chanctx_ops_assign_vif+0x1f9/0x210 [rtw89_core cbb375c44bf28564ce479002bff66617a25d9ac1]
? __mutex_unlock_slowpath+0xa0/0xf0
rtw89_ops_assign_vif_chanctx+0x4b/0x90 [rtw89_core cbb375c44bf28564ce479002bff66617a25d9ac1]
drv_assign_vif_chanctx+0xa7/0x1f0 [mac80211 6efaad16237edaaea0868b132d4f93ecf918a8b6]
ieee80211_reconfig+0x9cb/0x17b0 [mac80211 6efaad16237edaaea0868b132d4f93ecf918a8b6]
? __pfx_wiphy_resume+0x10/0x10 [cfg80211 572d03acaaa933fe38251be7fce3b3675284b8ed]
? dev_printk_emit+0x51/0x70
? _dev_info+0x6e/0x90
wiphy_resume+0x89/0x180 [cfg80211 572d03acaaa933fe38251be7fce3b3675284b8ed]
? __pfx_wiphy_resume+0x10/0x10 [cfg80211 572d03acaaa933fe38251be7fce3b3675284b8ed]
dpm_run_callback+0x37/0x1e0
device_resume+0x26d/0x4b0
? __pfx_dpm_watchdog_handler+0x10/0x10
async_resume+0x1d/0x30
async_run_entry_fn+0x29/0xd0
worker_thread+0x397/0x970
kthread+0xed/0x110
? __pfx_worker_thread+0x10/0x10
? __pfx_kthread+0x10/0x10
ret_from_fork+0x38/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
Fixes: 68ec751b2881 ("wifi: rtw89: chan: manage active interfaces")
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250103024500.14990-1-pkshih@realtek.com
|
|
Header conversion should only be used with MLO connections. Otherwise
P2P connection fails due to wrong probe responses sent. Fix it
accordingly.
Fixes: b8499664fca9 ("wifi: rtw89: Add header conversion for MLO connections")
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241231004811.8646-4-pkshih@realtek.com
|
|
During rtw89_entity_recalc_mgnt_roles(), there is a normalizing process
which will re-order the list if an entry with target pattern is found.
And once one is found, should have aborted the list_for_each_entry. But,
`break` just aborted the inner for-loop. The outer list_for_each_entry
still continues. Normally, only the first entry will match the target
pattern, and the re-ordering will change nothing, so there won't be
soft lockup. However, in some special cases, soft lockup would happen.
Fix it by `goto fill` to break from the list_for_each_entry.
The following is a sample of kernel log for this problem.
watchdog: BUG: soft lockup - CPU#1 stuck for 26s! [wpa_supplicant:2055]
[...]
RIP: 0010:rtw89_entity_recalc ([...] chan.c:392 chan.c:479) rtw89_core
[...]
Fixes: 68ec751b2881 ("wifi: rtw89: chan: manage active interfaces")
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241231004811.8646-3-pkshih@realtek.com
|
|
When starting/proceeding MCC, it will abort an ongoing hw scan process.
In the proceeding cases, it unexpectedly tries to abort a non-exist hw
scan process. Then, a trace shown at the bottom will happen. This problem
is caused by a previous commit which changed some call sequence inside
rtw89_hw_scan_complete() to fix some coex problems. These changes lead
to our scanning flag was not cleared when proceeding MCC. To keep the
fixes on coex, and resolve the problem here, re-consider the related
call sequence.
The known sequence requirements are listed below.
* the old sequence:
A. notify coex
B. clear scanning flag
C. proceed chanctx
C-1. set channel
C-2. proceed MCC
(the problem: A needs to be after C-1)
* the current sequence:
C. proceed chanctx
C-1. set channel
C-2. proceed MCC
A. notify coex
B. clear scanning flag
(the problem: C-2 needs to be after B)
So, now let hw scan caller pass a callback to proceed chanctx if needed.
Then, the new sequence will be like the below.
C-1. set channel
A. notify coex
B. clear scanning flag
C-2. proceed MCC
The following is the kernel log for the problem in current sequence.
rtw89_8852be 0000:04:00.0: rtw89_hw_scan_offload failed ret -110
------------[ cut here ]------------
[...]
CPU: 2 PID: 3991 Comm: kworker/u16:0 Tainted: G OE 6.6.17 #3
Hardware name: LENOVO 2356AD1/2356AD1, BIOS G7ETB3WW (2.73 ) 11/28/2018
Workqueue: events_unbound wiphy_work_cancel [cfg80211]
RIP: 0010:ieee80211_sched_scan_stopped+0xaea/0xd80 [mac80211]
Code: 9c 24 d0 11 00 00 49 39 dd 0f 85 46 ff ff ff 4c 89 e7 e8 09 2d
RSP: 0018:ffffb27783643d48 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: ffff8a2280964bc0 RSI: 0000000000000000 RDI: ffff8a23df580900
RBP: ffffb27783643d88 R08: 0000000000000001 R09: 0000000000000400
R10: 0000000000000000 R11: 0000000000008268 R12: ffff8a23df580900
R13: ffff8a23df581b00 R14: 0000000000000000 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff8a258e680000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f26a0654000 CR3: 000000002ea2e002 CR4: 00000000001706e0
Call Trace:
<TASK>
? show_regs+0x68/0x70
? ieee80211_sched_scan_stopped+0xaea/0xd80 [mac80211]
? __warn+0x8f/0x150
? ieee80211_sched_scan_stopped+0xaea/0xd80 [mac80211]
? report_bug+0x1f5/0x200
? handle_bug+0x46/0x80
? exc_invalid_op+0x19/0x70
? asm_exc_invalid_op+0x1b/0x20
? ieee80211_sched_scan_stopped+0xaea/0xd80 [mac80211]
ieee80211_scan_work+0x14a/0x650 [mac80211]
? __queue_work+0x10f/0x410
wiphy_work_cancel+0x2fb/0x310 [cfg80211]
process_scheduled_works+0x9d/0x390
? __pfx_worker_thread+0x10/0x10
worker_thread+0x15b/0x2d0
? __pfx_worker_thread+0x10/0x10
kthread+0x108/0x140
? __pfx_kthread+0x10/0x10
ret_from_fork+0x3c/0x60
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
---[ end trace 0000000000000000 ]---
Fixes: f16c40acd319 ("wifi: rtw89: Fix TX fail with A2DP after scanning")
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241231004811.8646-2-pkshih@realtek.com
|
|
Realtek's chips follow suggestion of PCIe spec to design the max timeout of
PCI completion, but some PCIe host reply too slow to meet it and lead PCI
AER. Disable PCI completion timeout function via PCI configuration to
avoid the AER.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241225122804.10214-1-pkshih@realtek.com
|
|
A user reports that the firmware upload consistently fails when it's
uploaded in chunks of 128 bytes, but it works when uploaded in chunks
of 196 bytes. The official driver uses 196 bytes also.
Link: https://github.com/a5a5aa555oo/rtl8xxxu/issues/2
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/cba8e2f2-32c4-4174-90ba-0219f29dbdde@gmail.com
|
|
The regd enum was extended for these countries. But, the dbgfs doesn't
recognize them yet. So, add them.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241219014545.9157-1-pkshih@realtek.com
|
|
To have better tuning of TX duty for fields usage, adjust thermal
protection step to 5, then TX duty reduce to 75% at most. Add RTL8852BE-VT
ID to enable this function by the way.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241219014511.9056-1-pkshih@realtek.com
|
|
The USB driver uses four USB Request Blocks for RX. Before submitting
one, it allocates a 32768 byte skb for the RX data. This allocation can
fail, maybe due to temporary memory fragmentation. When the allocation
fails, the corresponding URB is never submitted again. After four such
allocation failures, all RX stops because the driver is not requesting
data from the device anymore.
Don't allocate a 32768 byte skb when submitting a USB Request Block
(which happens very often). Instead preallocate 8 such skbs, and reuse
them over and over. If all 8 are busy, allocate a new one. This is
pretty rare. If the allocation fails, use a work to try again later.
When there are enough free skbs again, free the excess skbs.
Also, use WQ_BH for the RX workqueue. With a normal or high priority
workqueue the skbs are processed too slowly when the system is even a
little busy, like when opening a new page in a browser, and the driver
runs out of free skbs and allocates a lot of new ones.
This is more or less what the out-of-tree Realtek drivers do, except
they use a tasklet instead of a BH workqueue.
Tested with RTL8723DU, RTL8821AU, RTL8812AU, RTL8812BU, RTL8822CU,
RTL8811CU.
Closes: https://lore.kernel.org/linux-wireless/6e7ecb47-7ea0-433a-a19f-05f88a2edf6b@gmail.com/
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/9cee7a34-c38d-4128-824d-0ec139ca5a4e@gmail.com
|
|
The firmware message C2H_ADAPTIVITY is currently handled in
rtw_fw_c2h_cmd_rx_irqsafe(), which runs in the RX workqueue, but it's
not "irqsafe" with USB because it sleeps (reads hardware registers).
This becomes a problem after the next patch, which will create the RX
workqueue with the flag WQ_BH.
To avoid sleeping when it's not allowed, handle C2H_ADAPTIVITY in
rtw_fw_c2h_cmd_handle(), which runs in the c2h workqueue.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/96e52b03-be8d-4050-ae71-bfdb478ff42f@gmail.com
|
|
"iperf3 -c 192.168.0.1 -R --udp -b 0" shows about 40% of datagrams
are lost. Many torrents don't download faster than 3 MiB/s, probably
because the Bittorrent protocol uses UDP. This is somehow related to
the use of skb_clone() in the RX path.
Don't use skb_clone(). Instead allocate a new skb for each 802.11 frame
received and copy the data from the big (32768 byte) skb.
With this patch, "iperf3 -c 192.168.0.1 -R --udp -b 0" shows only 1-2%
of datagrams are lost, and torrents can reach download speeds of 36
MiB/s.
Tested with RTL8812AU and RTL8822CU.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/8c9d4f9d-ebd8-4dc0-a0c4-9ebe430521dd@gmail.com
|
|
Some RTL8812AU devices fail to probe:
[ 12.478774] rtw_8812au 1-1.3:1.0: failed to dump efuse logical map
[ 12.487712] rtw_8812au 1-1.3:1.0: failed to setup chip efuse info
[ 12.487742] rtw_8812au 1-1.3:1.0: failed to setup chip information
[ 12.491077] rtw_8812au: probe of 1-1.3:1.0 failed with error -22
It turns out these chips don't need to "protect" any bytes at the end of
the efuse.
The original value of 96 was copied from rtw8821c.c.
No one reported any failures with RTL8821AU yet, but the vendor driver
uses the same efuse reading code for both chips.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/1a477adb-60c3-463c-b158-3f86c94cb821@gmail.com
|
|
RF front end type 2 exists in the wild and can be treated like types
0 and 1.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/2917c7fc-6d88-4007-b6a6-9130bd1991e5@gmail.com
|
|
RTL8821AE is stuck transmitting at the lowest rate allowed by the rate
mask. This is because the firmware doesn't know the device is connected
to a network.
Fix the macros SET_H2CCMD_MSRRPT_PARM_OPMODE and
SET_H2CCMD_MSRRPT_PARM_MACID_IND to work on the first byte of __cmd,
not the second. Now the firmware is correctly notified when the device
is connected to a network and it activates the rate control.
Before (MCS3):
[ 5] 0.00-1.00 sec 12.5 MBytes 105 Mbits/sec 0 339 KBytes
[ 5] 1.00-2.00 sec 10.6 MBytes 89.1 Mbits/sec 0 339 KBytes
[ 5] 2.00-3.00 sec 10.6 MBytes 89.1 Mbits/sec 0 386 KBytes
[ 5] 3.00-4.00 sec 10.6 MBytes 89.1 Mbits/sec 0 386 KBytes
[ 5] 4.00-5.00 sec 10.2 MBytes 86.0 Mbits/sec 0 427 KBytes
After (MCS9):
[ 5] 0.00-1.00 sec 33.9 MBytes 284 Mbits/sec 0 771 KBytes
[ 5] 1.00-2.00 sec 31.6 MBytes 265 Mbits/sec 0 865 KBytes
[ 5] 2.00-3.00 sec 29.9 MBytes 251 Mbits/sec 0 963 KBytes
[ 5] 3.00-4.00 sec 28.2 MBytes 237 Mbits/sec 0 963 KBytes
[ 5] 4.00-5.00 sec 26.8 MBytes 224 Mbits/sec 0 963 KBytes
Fixes: 39f40710d0b5 ("rtlwifi: rtl88821ae: Remove usage of private bit manipulation macros")
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/754785b3-8a78-4554-b80d-de5f603b410b@gmail.com
|
|
The layout struct of efuse should not do address alignment by compiler.
Otherwise it leads unexpected layout and size for certain arch suc as arm.
In x86-64, the results are identical before and after this patch.
Also adjust bit-field to prevent over adjacent byte to avoid warning:
rtw88/rtw8822b.h:66:1: note: offset of packed bit-field `res2` has changed in GCC 4.4
66 | } __packed;
| ^
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202412120131.qk0x6OhE-lkp@intel.com/
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241212054203.135046-1-pkshih@realtek.com
|
|
rtw-next patches for v6.14
Regular development in this period. Main changes are listed:
rtl8xxxu:
* add more USB devices IDs
rtlwifi:
* refine error path
rtw88:
* add more USB devices IDs
* enable USB RX aggregation and USB 3 to improve performance
rtw89:
* implement more stuffs including PS flow for MLO
|
|
Including the fwil.h header file can lead to a build error:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwil.h: \
In function ‘brcmf_fil_cmd_int_set’:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwil.h:90:9: error: implicit \
declaration of function ‘brcmf_dbg’ [-Werror=implicit-function-declaration]
90 | brcmf_dbg(FIL, "ifidx=%d, cmd=%d, value=%d\n", ifp->ifidx, cmd, data);
| ^~~~~~~~~
The error is often avoided because the debug.h header file is included
before the fwil.h header file.
This makes sure the header include order is irrelevant by explicitly adding the
debug.h header.
Fixes: 31343230abb1 ("wifi: brcmfmac: export firmware interface functions")
Signed-off-by: Marcel Hamer <marcel.hamer@windriver.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241211133618.2014083-1-marcel.hamer@windriver.com
|
|
In 'wlc_phy_iqcal_gainparams_nphy()', add gain range check to WARN()
instead of possible out-of-bounds 'tbl_iqcal_gainparams_nphy' access.
Compile tested only.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241210070441.836362-1-dmantipov@yandex.ru
|
|
Fix specific spelling error in core.h.
Signed-off-by: Liu Jing <liujing@cmss.chinamobile.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241209062425.4139-1-liujing@cmss.chinamobile.com
|
|
The newer firmware, lik RTL8852C version 0.27.111.0, will notify driver
report of TAS (Time Averaged SAR) power by new C2H events. This is to
assist in higher accurate calculation of TAS.
For now, driver doesn't use the report yet, so add a dummy handler to
avoid it throws info like:
rtw89_8852ce 0000:03:00.0: c2h class 9 func 6 not support
Also add "MAC" and "PHY" to the message to disambiguate the source of
C2H event.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241209042127.21424-1-pkshih@realtek.com
|
|
_dpk_dgain_read()
The return value of _dpk_dgain_read() is not used afterward, so remove
it safely.
Addresses-Coverity-ID: 1504753 ("Unused value")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241209042020.21290-2-pkshih@realtek.com
|
|
_rx_dck_channel_calc()
The channel is not possibly 0, so original code is fine. Still want to
avoid Coverity warning, so ensure -32 offset for the channel number which
is larger than 125 only. Actually, don't change logic at all.
Addresses-Coverity-ID: 1628150 ("Overflowed constant")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241209042020.21290-1-pkshih@realtek.com
|
|
At probe error path, the firmware loading work may have already been
queued. In such a case, it will try to access memory allocated by the probe
function, which is about to be released. In such paths, wait for the
firmware worker to finish before releasing memory.
Fixes: 3d86b93064c7 ("rtlwifi: Fix PCI probe error path orphaned memory")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241206173713.3222187-5-cascardo@igalia.com
|
|
Deinitialize at reverse order when probe fails.
When init_sw_vars fails, rtl_deinit_core should not be called, specially
now that it destroys the rtl_wq workqueue.
And call rtl_pci_deinit and deinit_sw_vars, otherwise, memory will be
leaked.
Remove pci_set_drvdata call as it will already be cleaned up by the core
driver code and could lead to memory leaks too. cf. commit 8d450935ae7f
("wireless: rtlwifi: remove unnecessary pci_set_drvdata()") and
commit 3d86b93064c7 ("rtlwifi: Fix PCI probe error path orphaned memory").
Fixes: 0c8173385e54 ("rtl8192ce: Add new driver")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241206173713.3222187-4-cascardo@igalia.com
|
|
rtl_wq is allocated at rtl_init_core, so it makes more sense to destroy it
at rtl_deinit_core. In the case of USB, where _rtl_usb_init does not
require anything to be undone, that is fine. But for PCI, rtl_pci_init,
which is called after rtl_init_core, needs to deallocate data, but only if
it has been called.
That means that destroying the workqueue needs to be done whether
rtl_pci_init has been called or not. And since rtl_pci_deinit was doing it,
it has to be moved out of there.
It makes more sense to move it to rtl_deinit_core and have it done in both
cases, USB and PCI.
Since this is a requirement for a followup memory leak fix, mark this as
fixing such memory leak.
Fixes: 0c8173385e54 ("rtl8192ce: Add new driver")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241206173713.3222187-3-cascardo@igalia.com
|
|
Commit 2461c7d60f9f ("rtlwifi: Update header file") introduced a global
list of private data structures.
Later on, commit 26634c4b1868 ("rtlwifi Modify existing bits to match
vendor version 2013.02.07") started adding the private data to that list at
probe time and added a hook, check_buddy_priv to find the private data from
a similar device.
However, that function was never used.
Besides, though there is a lock for that list, it is never used. And when
the probe fails, the private data is never removed from the list. This
would cause a second probe to access freed memory.
Remove the unused hook, structures and members, which will prevent the
potential race condition on the list and its corruption during a second
probe when probe fails.
Fixes: 26634c4b1868 ("rtlwifi Modify existing bits to match vendor version 2013.02.07")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241206173713.3222187-2-cascardo@igalia.com
|
|
The RFK pre-notify H2C command is to tell firmware the channels driver is
using. Since the format is changed after 0.35.49.0, update it accordingly.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241206055716.18598-8-pkshih@realtek.com
|
|
Sync Realtek Channel Plan R68 and Realtek Regulatory R51.
Configure 6 GHz field of Realtek regd for the following countries.
BO, DO, EG, LS, MZ, NG, OM, ZW, PK, PH, TH, KM, CG, CD,
GE, GI, GU, LR, MH, FM, MP, PW, MF, SX, SZ, TZ, VI
Besides, add entries for the following countries.
CU, SY, SD
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241206055716.18598-7-pkshih@realtek.com
|
|
Since hardware only has single one register for HE-LTF setting,
to prevent interoperability issues, 8852CE disables ER SU when
the AP can handle SU/MU with 4x HE-LTF and 0.8 GI, but does
not support ER SU with the same settings.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241206055716.18598-6-pkshih@realtek.com
|
|
Given the performance trade-off associated with firmware training
HE GI/LTF, especially in high attenuation environments, we have
decided to utilize a constant value instead.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241206055716.18598-5-pkshih@realtek.com
|
|
before/after PS
For MLO supported IC, send H2C command to firmware before PS with link
information for each PHY for MLO to work properly. And re-init hardware
settings regarding to RX descriptor information after PS.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241206055716.18598-4-pkshih@realtek.com
|
|
In PS mode, firmware needs hardware parameters related to channel info
to configure hardware itself. Before entering PS, driver prepares these
info to firmware via firmware H2C command.
Since firmware only consider PS for single one vif, change the argument
of entry function to rtwvif, and only consider first link for this old
H2C command that only support legacy.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241206055716.18598-3-pkshih@realtek.com
|
|
Firmware can only support PS on single one VIF operating in station mode,
so argument of PS entry rtw89_enter_lps() should be rtwvif insetad of
rtwvif_link.
To enter PS under MLO, for each rtwvif, driver sends H2C command to tell
firmware which mac_id will enter PS one by one, and afterward asks
firmware to enter deep PS.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241206055716.18598-2-pkshih@realtek.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
ath.git patches for v6.14
This development cycle featured multiple patchsets to ath12k to
support the new 802.11be MLO feature, although the feature is still
incomplete. Also in ath12k, there were other feature patches. In
ath11k, support was added for QCA6698AQ. And there was the usual set
of bug fixes and cleanups across most drivers, notable being the
addition of "noinline_for_stack" to some functions to avoid "stack
frame size" warnings when compiling with clang.
|
|
In commit 52250cbee7f6 ("mwifiex: use timeout variant for
wait_event_interruptible") it was noted that sometimes we seemed
to miss the signal that our host sleep settings took effect. A
10 second timeout was added to the code to make sure we didn't
hang forever waiting. It appears that this problem still exists
and we hit the timeout sometimes for Chromebooks in the field.
Recently on ChromeOS we've started setting the DPM watchdog
to trip if full system suspend takes over 10 seconds. Given
the timeout in the original patch, obviously we're hitting
the DPM watchdog before mwifiex gets a chance to timeout.
While we could increase the DPM watchdog in ChromeOS to avoid
this problem, it's probably better to simply decrease the
timeout. Any time we're waiting several seconds for the
firmware to respond it's likely that the firmware won't ever
respond. With that in mind, decrease the timeout in mwifiex
from 10 seconds to 5 seconds.
Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241127105709.4014302-1-treapking@chromium.org
|
|
This removes the following error log when stopping AP:
ieee80211 phy0: brcmf_vif_set_mgmt_ie: vndr ie set error : -52
It happened if:
1) previously wlan interface was in station mode (wpa_supplicant) and
connected to a hotspot
2) then started AP mode (hostapd)
3) and then stopped AP mode.
The error happened when it tried to clear BRCMF_VNDR_IE_PRBREQ_FLAG.
This flag is not set in `brcmf_config_ap_mgmt_ie`, but
BRCMF_VNDR_IE_ASSOCRSP_FLAG is set instead.
Signed-off-by: Renjaya Raga Zenta <ragazenta@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241121-brcmfmac-v1-1-02fc3fb427c2@gmail.com
|
|
'struct nla_policy' is not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increase overall security, especially when the structure holds some
function pointers.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
5062 528 0 5590 15d6 drivers/net/wireless/ti/wlcore/testmode.o
After:
=====
text data bss dec hex filename
5178 404 0 5582 15ce drivers/net/wireless/ti/wlcore/testmode.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/78810e3ebb74ddbd3a4538f182bf1143b89baba7.1731332414.git.christophe.jaillet@wanadoo.fr
|
|
The scatter-gather handling uses a pre-allocated list (with nents entries).
If the driver runs out of sg entries it will result in an oops. Let's detect
this instead and make the SDIO block transfer fail.
Signed-off-by: Norbert van Bolhuis <nvbolhuis@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241108125609.107016-1-nvbolhuis@gmail.com
|
|
Currently, during mac80211 allocate and register single device is
considered for the registration. But, in future, during multi device
group abstraction is introduced, all the devices has to be combined
together as a single abstraction and then hardware should be allocated.
All the devices in the group should be combined together only if it
supports inter device mlo capability. The decision of whether to combine
the devices or not can be based on the mlo capability flag in
ath12k_hw_group.
By default, mlo_capable flag in the group would be set as false. During
QMI PHY capability exchange, only when we have more than one chip in the
group or if one chip, then that chip supports inter MLO, then mlo_capable
flag in the group will be enabled.
Add changes to introduce mlo_capable flag for device group and refactor
ath12k_mac_hw_allocate() api based on device group (ag) rather than
device (ab).
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241204163216.433795-8-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
QMI host capability has the information regarding MLO parameters such as
device_id, MLO capability, group id and the information of each devices
involved in the group and sent immediately on QMI server arrive event.
Currently, only one device is involved in the group and hence, single
device information is sent as part of MLO capability of host.
But, in future when multi device group abstraction is introduced, host
should send all the device information involved in the group as part
of QMI MLO host capability rather than single device. Hence, sending
QMI host capability immediately on server arrive of a device might not
be ideal for multi device group abstraction as the details of other
devices in the group would not be available.
Hence, once QMI server arrive event is received, request for QMI PHY
capabilities of device, and defer the host capability send for that device.
After QMI PHY capability is received for all the devices in the group
trigger the host capability event for the deferred devices in the group.
Hence, add changes to defer the QMI host capability event until the device
group is ready and then resume the QMI exchange for all the device with
host capabilities.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241204163216.433795-7-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
