| Age | Commit message (Collapse) | Author |
|---|
|
Add a compatible for SFP+ cages. SFP+ cages are backwards compatible,
but the ethernet device behind them may not support the slower speeds
of SFP modules.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Allow the Marvell 10G PHY to register with the SFP bus, so that SFP+
cages can work. This bypasses phylink, meaning that socket status
is not taken into account for the link state. Also, the tx-disable
signal must be commented out in DT for this to work...
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
mvneta is the only user of fixed_phy_update_state(), which has been
converted to use phylink instead. Remove fixed_phy_update_state().
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The PSC sync change interrupt can fire multiple times while the link is
down. As this isn't information we make use of, it's pointless having
the interrupt enabled, so let's disable this interrupt.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Convert mvneta to use phylink, which models the MAC to PHY link in
a generic, reusable form.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- remove unused sync status
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add support for SFP hotpluggable modules via sfp-bus and phylink.
This supports both copper and optical SFP modules, which require
different Serdes modes in order to properly negotiate the link.
Optical SFP modules typically require the Serdes link to be talking
1000BaseX mode - this is the gigabit ethernet mode defined by the
802.3 standard.
Copper SFP modules typically integrate a PHY in the module to convert
from Serdes to copper, and the PHY will be configured by the vendor
to either present a 1000BaseX Serdes link (for fixed 1000BaseT) or a
SGMII Serdes link. However, this is vendor defined, so we instead
detect the PHY, switch the link to SGMII mode, and use traditional
PHY based negotiation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add in-band autonegotation support for 10GBase-KR mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add support for reading and writing the clause 45 MII registers.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add support for reading module EEPROMs through phylink.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The link between the ethernet MAC and its PHY has become more complex
as the interface evolves. This is especially true with serdes links,
where the part of the PHY is effectively integrated into the MAC.
Serdes links can be connected to a variety of devices, including SFF
modules soldered down onto the board with the MAC, a SFP cage with
a hotpluggable SFP module which may contain a PHY or directly modulate
the serdes signals onto optical media with or without a PHY, or even
a classical PHY connection.
Moreover, the negotiation information on serdes links comes in two
varieties - SGMII mode, where the PHY provides its speed/duplex/flow
control information to the MAC, and 1000base-X mode where both ends
exchange their abilities and each resolve the link capabilities.
This means we need a more flexible means to support these arrangements,
particularly with the hotpluggable nature of SFP, where the PHY can
be attached or detached after the network device has been brought up.
Ethtool information can come from multiple sources:
- we may have a PHY operating in either SGMII or 1000base-X mode, in
which case we take ethtool/mii data directly from the PHY.
- we may have a optical SFP module without a PHY, with the MAC
operating in 1000base-X mode - the ethtool/mii data needs to come
from the MAC.
- we may have a copper SFP module with a PHY whic can't be accessed,
which means we need to take ethtool/mii data from the MAC.
Phylink aims to solve this by providing an intermediary between the
MAC and PHY, providing a safe way for PHYs to be hotplugged, and
allowing a SFP driver to reconfigure the serdes connection.
Phylink also takes over support of fixed link connections, where the
speed/duplex/flow control are fixed, but link status may be controlled
by a GPIO signal. By avoiding the fixed-phy implementation, phylink
can provide a faster response to link events: fixed-phy has to wait for
phylib to operate its state machine, which can take several seconds.
In comparison, phylink takes milliseconds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- remove sync status
- rework supported and advertisment handling
- add 1000base-x speed for fixed links
- use functionality exported from phy-core, reworking
__phylink_ethtool_ksettings_set for it
|
|
Add an I2C MDIO bus bridge library, to allow phylib to access PHYs which
are connected to an I2C bus instead of the more conventional MDIO bus.
Such PHYs can be found in SFP adapters and SFF modules.
Since PHYs appear at I2C bus address 0x40..0x5f, and 0x50/0x51 are
reserved for SFP EEPROMs/diagnostics, we must not allow the MDIO bus
to access these I2C addresses.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
phylink will need phy_start_machine exported, so lets export it as a
GPL symbol. Documentation/networking/phy.txt indicates that this
should be a PHY API function.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Sometimes, we need to do additional work between the PHY coming up and
marking the carrier present - for example, we may need to wait for the
PHY to MAC link to finish negotiation. This changes phylib to provide
a notification function pointer which avoids the built-in
netif_carrier_on() and netif_carrier_off() functions.
Standard ->adjust_link functionality is provided by hooking a helper
into the new ->phy_link_change method.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add the missing 1000Base-X entry to the phy settings table. This was
not included because the original code could not cope with more than
32 bits of link mode mask.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
phy-core
phy_lookup_setting() provides useful functionality in ethtool code
outside phylib. Move it to phy-core and allow it to be re-used (eg,
in phylink) rather than duplicated elsewhere. Note that this supports
the larger linkmode space.
As we move the phy settings table, we also need to move the guts of
phy_supported_speeds() as well.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Other code would like to make use of this, so make the speed and duplex
string generation visible, and place it in a separate file.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Allow the phy settings table to support more than 32 link modes by
switching to the ethtool link mode bit number representation, rather
than storing the mask. This will allow phylink and other ethtool
code to share the settings table to look up settings.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add phylib support for the Marvell Alaska X 10 Gigabit PHY (MV88X3310).
This phy is able to operate at 10G, 1G, 100M and 10M speeds, and only
supports Clause 45 accesses.
The PHY appears (based on the vendor IDs) to be two different vendors
IP, with each devad containing several instances.
This PHY driver has only been tested with the RJ45 copper port, fiber
port and a Marvell Armada 8040-based ethernet interface.
It should be noted that to use the full range of speeds, MAC drivers
need to also reconfigure the link mode as per phydev->interface, since
the PHY automatically changes its interface mode depending on the
negotiated speed.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Move the old 10G genphy support to sit beside the new clause 45 library
functions, so all the 10G phy code is together.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
genphy_restart_aneg() can only restart autonegotiation on clause 22
PHYs. Add a phy_restart_aneg() function which selects between the
clause 22 and clause 45 restart functionality depending on the PHY
type.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add generic helpers for 802.3 clause 45 PHYs for >= 10Gbps support.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
When filter insertion fails with no rollback, we were trying to convert
EFX_EF10_FILTER_ID_INVALID to an id to store in 'ids' (which is either
vlan->uc or vlan->mc). This would WARN_ON_ONCE and then record a bogus
filter ID of 0x1fff, neither of which is a good thing.
Fixes: 0ccb998bf46d ("sfc: fix filter_id misinterpretation in edge case")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We add the pdev data to the pci devices netdev structure. This way
the interface get consistent device names in the userspace (udev).
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dev_id was miscalculated. Only the two bits 4-5 are relevant for the
MA1 card. PCIARC1 and PCIFB2 use the four bits 4-7 for id selection.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The assignment is superfluous.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch prevents the arcnet driver from the following deadlock.
[ 41.273910] ======================================================
[ 41.280397] [ INFO: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected ]
[ 41.287433] 4.4.0-00034-gc0ae784 #536 Not tainted
[ 41.292366] ------------------------------------------------------
[ 41.298863] arcecho/233 [HC0[0]:SC0[2]:HE0:SE0] is trying to acquire:
[ 41.305628] (&(&lp->lock)->rlock){+.+...}, at: [<bf083bc8>] arcnet_send_packet+0x60/0x1c0 [arcnet]
[ 41.315199]
[ 41.315199] and this task is already holding:
[ 41.321324] (_xmit_ARCNET#2){+.-...}, at: [<c06b934c>] packet_direct_xmit+0xfc/0x1c8
[ 41.329593] which would create a new lock dependency:
[ 41.334893] (_xmit_ARCNET#2){+.-...} -> (&(&lp->lock)->rlock){+.+...}
[ 41.341801]
[ 41.341801] but this new dependency connects a SOFTIRQ-irq-safe lock:
[ 41.350108] (_xmit_ARCNET#2){+.-...}
... which became SOFTIRQ-irq-safe at:
[ 41.357539] [<c06f8fc8>] _raw_spin_lock+0x30/0x40
[ 41.362677] [<c063ab8c>] dev_watchdog+0x5c/0x264
[ 41.367723] [<c0094edc>] call_timer_fn+0x6c/0xf4
[ 41.372759] [<c00950b8>] run_timer_softirq+0x154/0x210
[ 41.378340] [<c0036b30>] __do_softirq+0x144/0x298
[ 41.383469] [<c0036fb4>] irq_exit+0xcc/0x130
[ 41.388138] [<c0085c50>] __handle_domain_irq+0x60/0xb4
[ 41.393728] [<c0014578>] __irq_svc+0x58/0x78
[ 41.398402] [<c0010274>] arch_cpu_idle+0x24/0x3c
[ 41.403443] [<c007127c>] cpu_startup_entry+0x1f8/0x25c
[ 41.409029] [<c09adc90>] start_kernel+0x3c0/0x3cc
[ 41.414170]
[ 41.414170] to a SOFTIRQ-irq-unsafe lock:
[ 41.419931] (&(&lp->lock)->rlock){+.+...}
... which became SOFTIRQ-irq-unsafe at:
[ 41.427996] ... [<c06f8fc8>] _raw_spin_lock+0x30/0x40
[ 41.433409] [<bf083d54>] arcnet_interrupt+0x2c/0x800 [arcnet]
[ 41.439646] [<c0089120>] handle_nested_irq+0x8c/0xec
[ 41.445063] [<c03c1170>] regmap_irq_thread+0x190/0x314
[ 41.450661] [<c0087244>] irq_thread_fn+0x1c/0x34
[ 41.455700] [<c0087548>] irq_thread+0x13c/0x1dc
[ 41.460649] [<c0050f10>] kthread+0xe4/0xf8
[ 41.465158] [<c000f810>] ret_from_fork+0x14/0x24
[ 41.470207]
[ 41.470207] other info that might help us debug this:
[ 41.470207]
[ 41.478627] Possible interrupt unsafe locking scenario:
[ 41.478627]
[ 41.485763] CPU0 CPU1
[ 41.490521] ---- ----
[ 41.495279] lock(&(&lp->lock)->rlock);
[ 41.499414] local_irq_disable();
[ 41.505636] lock(_xmit_ARCNET#2);
[ 41.511967] lock(&(&lp->lock)->rlock);
[ 41.518741] <Interrupt>
[ 41.521490] lock(_xmit_ARCNET#2);
[ 41.525356]
[ 41.525356] *** DEADLOCK ***
[ 41.525356]
[ 41.531587] 1 lock held by arcecho/233:
[ 41.535617] #0: (_xmit_ARCNET#2){+.-...}, at: [<c06b934c>] packet_direct_xmit+0xfc/0x1c8
[ 41.544355]
the dependencies between SOFTIRQ-irq-safe lock and the holding lock:
[ 41.552362] -> (_xmit_ARCNET#2){+.-...} ops: 27 {
[ 41.557357] HARDIRQ-ON-W at:
[ 41.560664] [<c06f8fc8>] _raw_spin_lock+0x30/0x40
[ 41.567445] [<c063ba28>] dev_deactivate_many+0x114/0x304
[ 41.574866] [<c063bc3c>] dev_deactivate+0x24/0x38
[ 41.581646] [<c0630374>] linkwatch_do_dev+0x40/0x74
[ 41.588613] [<c06305d8>] __linkwatch_run_queue+0xec/0x140
[ 41.596120] [<c0630658>] linkwatch_event+0x2c/0x34
[ 41.602991] [<c004af30>] process_one_work+0x188/0x40c
[ 41.610131] [<c004b200>] worker_thread+0x4c/0x480
[ 41.616912] [<c0050f10>] kthread+0xe4/0xf8
[ 41.623048] [<c000f810>] ret_from_fork+0x14/0x24
[ 41.629735] IN-SOFTIRQ-W at:
[ 41.633039] [<c06f8fc8>] _raw_spin_lock+0x30/0x40
[ 41.639820] [<c063ab8c>] dev_watchdog+0x5c/0x264
[ 41.646508] [<c0094edc>] call_timer_fn+0x6c/0xf4
[ 41.653190] [<c00950b8>] run_timer_softirq+0x154/0x210
[ 41.660425] [<c0036b30>] __do_softirq+0x144/0x298
[ 41.667201] [<c0036fb4>] irq_exit+0xcc/0x130
[ 41.673518] [<c0085c50>] __handle_domain_irq+0x60/0xb4
[ 41.680754] [<c0014578>] __irq_svc+0x58/0x78
[ 41.687077] [<c0010274>] arch_cpu_idle+0x24/0x3c
[ 41.693769] [<c007127c>] cpu_startup_entry+0x1f8/0x25c
[ 41.701006] [<c09adc90>] start_kernel+0x3c0/0x3cc
[ 41.707791] INITIAL USE at:
[ 41.711003] [<c06f8fc8>] _raw_spin_lock+0x30/0x40
[ 41.717696] [<c063ba28>] dev_deactivate_many+0x114/0x304
[ 41.725026] [<c063bc3c>] dev_deactivate+0x24/0x38
[ 41.731718] [<c0630374>] linkwatch_do_dev+0x40/0x74
[ 41.738593] [<c06305d8>] __linkwatch_run_queue+0xec/0x140
[ 41.746011] [<c0630658>] linkwatch_event+0x2c/0x34
[ 41.752789] [<c004af30>] process_one_work+0x188/0x40c
[ 41.759847] [<c004b200>] worker_thread+0x4c/0x480
[ 41.766541] [<c0050f10>] kthread+0xe4/0xf8
[ 41.772596] [<c000f810>] ret_from_fork+0x14/0x24
[ 41.779198] }
[ 41.780945] ... key at: [<c124d620>] netdev_xmit_lock_key+0x38/0x1c8
[ 41.788192] ... acquired at:
[ 41.791309] [<c007bed8>] lock_acquire+0x70/0x90
[ 41.796361] [<c06f9140>] _raw_spin_lock_irqsave+0x40/0x54
[ 41.802324] [<bf083bc8>] arcnet_send_packet+0x60/0x1c0 [arcnet]
[ 41.808844] [<c06b9380>] packet_direct_xmit+0x130/0x1c8
[ 41.814622] [<c06bc7e4>] packet_sendmsg+0x3b8/0x680
[ 41.820034] [<c05fe8b0>] sock_sendmsg+0x14/0x24
[ 41.825091] [<c05ffd68>] SyS_sendto+0xb8/0xe0
[ 41.829956] [<c05ffda8>] SyS_send+0x18/0x20
[ 41.834638] [<c000f780>] ret_fast_syscall+0x0/0x1c
[ 41.839954]
[ 41.841514]
the dependencies between the lock to be acquired and SOFTIRQ-irq-unsafe lock:
[ 41.850302] -> (&(&lp->lock)->rlock){+.+...} ops: 5 {
[ 41.855644] HARDIRQ-ON-W at:
[ 41.858945] [<c06f8fc8>] _raw_spin_lock+0x30/0x40
[ 41.865726] [<bf083d54>] arcnet_interrupt+0x2c/0x800 [arcnet]
[ 41.873607] [<c0089120>] handle_nested_irq+0x8c/0xec
[ 41.880666] [<c03c1170>] regmap_irq_thread+0x190/0x314
[ 41.887901] [<c0087244>] irq_thread_fn+0x1c/0x34
[ 41.894593] [<c0087548>] irq_thread+0x13c/0x1dc
[ 41.901195] [<c0050f10>] kthread+0xe4/0xf8
[ 41.907338] [<c000f810>] ret_from_fork+0x14/0x24
[ 41.914025] SOFTIRQ-ON-W at:
[ 41.917328] [<c06f8fc8>] _raw_spin_lock+0x30/0x40
[ 41.924106] [<bf083d54>] arcnet_interrupt+0x2c/0x800 [arcnet]
[ 41.931981] [<c0089120>] handle_nested_irq+0x8c/0xec
[ 41.939028] [<c03c1170>] regmap_irq_thread+0x190/0x314
[ 41.946264] [<c0087244>] irq_thread_fn+0x1c/0x34
[ 41.952954] [<c0087548>] irq_thread+0x13c/0x1dc
[ 41.959548] [<c0050f10>] kthread+0xe4/0xf8
[ 41.965689] [<c000f810>] ret_from_fork+0x14/0x24
[ 41.972379] INITIAL USE at:
[ 41.975595] [<c06f8fc8>] _raw_spin_lock+0x30/0x40
[ 41.982283] [<bf083d54>] arcnet_interrupt+0x2c/0x800 [arcnet]
[ 41.990063] [<c0089120>] handle_nested_irq+0x8c/0xec
[ 41.997027] [<c03c1170>] regmap_irq_thread+0x190/0x314
[ 42.004172] [<c0087244>] irq_thread_fn+0x1c/0x34
[ 42.010766] [<c0087548>] irq_thread+0x13c/0x1dc
[ 42.017267] [<c0050f10>] kthread+0xe4/0xf8
[ 42.023314] [<c000f810>] ret_from_fork+0x14/0x24
[ 42.029903] }
[ 42.031648] ... key at: [<bf0854cc>] __key.42091+0x0/0xfffff0f8 [arcnet]
[ 42.039255] ... acquired at:
[ 42.042372] [<c007bed8>] lock_acquire+0x70/0x90
[ 42.047413] [<c06f9140>] _raw_spin_lock_irqsave+0x40/0x54
[ 42.053364] [<bf083bc8>] arcnet_send_packet+0x60/0x1c0 [arcnet]
[ 42.059872] [<c06b9380>] packet_direct_xmit+0x130/0x1c8
[ 42.065634] [<c06bc7e4>] packet_sendmsg+0x3b8/0x680
[ 42.071030] [<c05fe8b0>] sock_sendmsg+0x14/0x24
[ 42.076069] [<c05ffd68>] SyS_sendto+0xb8/0xe0
[ 42.080926] [<c05ffda8>] SyS_send+0x18/0x20
[ 42.085601] [<c000f780>] ret_fast_syscall+0x0/0x1c
[ 42.090918]
[ 42.092481]
[ 42.092481] stack backtrace:
[ 42.097065] CPU: 0 PID: 233 Comm: arcecho Not tainted 4.4.0-00034-gc0ae784 #536
[ 42.104751] Hardware name: Generic AM33XX (Flattened Device Tree)
[ 42.111183] [<c0017ec8>] (unwind_backtrace) from [<c00139d0>] (show_stack+0x10/0x14)
[ 42.119337] [<c00139d0>] (show_stack) from [<c02a82c4>] (dump_stack+0x8c/0x9c)
[ 42.126937] [<c02a82c4>] (dump_stack) from [<c0078260>] (check_usage+0x4bc/0x63c)
[ 42.134815] [<c0078260>] (check_usage) from [<c0078438>] (check_irq_usage+0x58/0xb0)
[ 42.142964] [<c0078438>] (check_irq_usage) from [<c007aaa0>] (__lock_acquire+0x1524/0x20b0)
[ 42.151740] [<c007aaa0>] (__lock_acquire) from [<c007bed8>] (lock_acquire+0x70/0x90)
[ 42.159886] [<c007bed8>] (lock_acquire) from [<c06f9140>] (_raw_spin_lock_irqsave+0x40/0x54)
[ 42.168768] [<c06f9140>] (_raw_spin_lock_irqsave) from [<bf083bc8>] (arcnet_send_packet+0x60/0x1c0 [arcnet])
[ 42.179115] [<bf083bc8>] (arcnet_send_packet [arcnet]) from [<c06b9380>] (packet_direct_xmit+0x130/0x1c8)
[ 42.189182] [<c06b9380>] (packet_direct_xmit) from [<c06bc7e4>] (packet_sendmsg+0x3b8/0x680)
[ 42.198059] [<c06bc7e4>] (packet_sendmsg) from [<c05fe8b0>] (sock_sendmsg+0x14/0x24)
[ 42.206199] [<c05fe8b0>] (sock_sendmsg) from [<c05ffd68>] (SyS_sendto+0xb8/0xe0)
[ 42.213978] [<c05ffd68>] (SyS_sendto) from [<c05ffda8>] (SyS_send+0x18/0x20)
[ 42.221388] [<c05ffda8>] (SyS_send) from [<c000f780>] (ret_fast_syscall+0x0/0x1c)
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
---
v1 -> v2: removed unneeded zero assignment of flags
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
My static checker complains that ofdpa_neigh_del() can sometimes free
"found". It just makes sense to use it first before deleting it.
Fixes: ecf244f753e0 ("rocker: fix maybe-uninitialized warning")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case a VLAN device is enslaved to a bridge we shouldn't create a
router interface (RIF) for it when it's configured with an IP address.
This is already handled by the driver for other types of netdevs, such
as physical ports and LAG devices.
If this IP address is then removed and the interface is subsequently
unlinked from the bridge, a NULL pointer dereference can happen, as the
original 802.1d FID was replaced with an rFID which was then deleted.
To reproduce:
$ ip link set dev enp3s0np9 up
$ ip link add name enp3s0np9.111 link enp3s0np9 type vlan id 111
$ ip link set dev enp3s0np9.111 up
$ ip link add name br0 type bridge
$ ip link set dev br0 up
$ ip link set enp3s0np9.111 master br0
$ ip address add dev enp3s0np9.111 192.168.0.1/24
$ ip address del dev enp3s0np9.111 192.168.0.1/24
$ ip link set dev enp3s0np9.111 nomaster
Fixes: 99724c18fc66 ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Petr Machata <petrm@mellanox.com>
Tested-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't hold any tx lock when trying to disable TX during reset, this
would lead a use after free since ndo_start_xmit() tries to access
the virtqueue which has already been freed. Fix this by using
netif_tx_disable() before freeing the vqs, this could make sure no tx
after vq freeing.
Reported-by: Jean-Philippe Menil <jpmenil@gmail.com>
Tested-by: Jean-Philippe Menil <jpmenil@gmail.com>
Fixes commit f600b6905015 ("virtio_net: Add XDP support")
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Robert McCabe <robert.mccabe@rockwellcollins.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Belkin B2B128 is a USB 3.0 Hub + Gigabit Ethernet Adapter, the
Ethernet adapter uses the ASIX AX88179 USB 3.0 to Gigabit Ethernet
chip supported by this driver, add the USB ID for the same.
This patch is based on work by Geoffrey Tran <geoffrey.tran@gmail.com>
who has indicated they would like this upstreamed by someone more
familiar with the upstreaming process.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A previous commit (5567e989198b5a8d) inserted a dependency on DMA
API that requires HAS_DMA to be added in Kconfig.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When mc configuration changes bnx2x_config_mcast() can return 0 for
success, negative for failure and positive for benign reason preventing
its immediate work, e.g., when the command awaits the completion of
a previously sent command.
When removing all configured macs on a 578xx adapter, if a positive
value would be returned driver would errneously log it as an error.
Fixes: c7b7b483ccc9 ("bnx2x: Don't flush multicast MACs")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To handle netpoll properly, the driver must only handle TX packets
during NAPI. Handling RX events cause warnings and errors in
netpoll mode. The ndo_poll_controller() method should call
napi_schedule() directly so that a NAPI weight of zero will be used
during netpoll mode.
The bnxt_en driver supports 2 ring modes: combined, and separate rx/tx.
In separate rx/tx mode, the ndo_poll_controller() method will only
process the tx rings. In combined mode, the rx and tx completion
entries are mixed in the completion ring and we need to drop the rx
entries and recycle the rx buffers.
Add a function bnxt_force_rx_discard() to handle this in netpoll mode
when we see rx entries in combined ring mode.
Reported-by: Calvin Owens <calvinowens@fb.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we get a TPA_END completion to handle a completed LRO packet, it
is possible that hardware would indicate errors. The current code is
not checking for the error condition. Define the proper error bits and
the macro to check for this error and abort properly.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function, skb_complete_tx_timestamp(), used to allow passing in a
NULL pointer for the time stamps, but that was changed in commit
62bccb8cdb69051b95a55ab0c489e3cab261c8ef ("net-timestamp: Make the
clone operation stand-alone from phy timestamping"), and the existing
call sites, all of which are in the dp83640 driver, were fixed up.
Even though the kernel-doc was subsequently updated in commit
7a76a021cd5a292be875fbc616daf03eab1e6996 ("net-timestamp: Update
skb_complete_tx_timestamp comment"), still a bug fix from Manfred
Rudigier came into the driver using the old semantics. Probably
Manfred derived that patch from an older kernel version.
This fix should be applied to the stable trees as well.
Fixes: 81e8f2e930fe ("net: dp83640: Fix tx timestamp overflow handling.")
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 8000 series adapters uses catch-all filters for encapsulated traffic
to support filtering VXLAN, NVGRE and GENEVE traffic.
This new filter functionality requires a longer MCDI command.
This patch increases the size of buffers on stack that were missed, which
fixes a kernel panic from the stack protector.
Fixes: 9b41080125176 ("sfc: insert catch-all filters for encapsulated traffic")
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Acked-by: Bert Kenward bkenward@solarflare.com
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This structure member is hidden behind CONFIG_SYSFS, and we
get a build error when that is disabled:
drivers/net/hyperv/netvsc_drv.c: In function 'netvsc_set_channels':
drivers/net/hyperv/netvsc_drv.c:754:49: error: 'struct net_device' has no member named 'num_rx_queues'; did you mean 'num_tx_queues'?
drivers/net/hyperv/netvsc_drv.c: In function 'netvsc_set_rxfh':
drivers/net/hyperv/netvsc_drv.c:1181:25: error: 'struct net_device' has no member named 'num_rx_queues'; did you mean 'num_tx_queues'?
As the value is only set once to the argument of alloc_netdev_mq(),
we can compare against that constant directly.
Fixes: ff4a44199012 ("netvsc: allow get/set of RSS indirection table")
Fixes: 2b01888d1b45 ("netvsc: allow more flexible setting of number of channels")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Passthru macvlans directly change the mac address of the lower
level device. That's OK, but after the macvlan is deleted,
the lower device is left with changed address and one needs to
reboot to bring back the origina HW addresses.
This scenario is actually quite common with passthru macvtap devices.
This patch attempts to solve this, by storing the mac address
of the lower device in macvlan_port structure and keeping track of
it through the changes.
After this patch, any changes to the lower device mac address
done trough the macvlan device, will be reverted back. Any
changs done directly to the lower device mac address will be kept.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert the port passthru boolean into flags with accesor functions.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a lower device of the passthru macvlan changes it's address,
passthru macvlan is supposed to change it's own address as well.
However, that doesn't happen correctly because the check in
macvlan_addr_busy() will catch the fact that the lower level
(port) mac address is the same as the address we are trying to
assign to the macvlan, and return an error. As a reasult,
the address of the passthru macvlan device is never changed.
The same thing happens when the user attempts to change the
mac address of the passthru macvlan.
The simple solution appers to be to not check against
the lower device in case of passthru macvlan device, since
the 2 addresses are _supposed_ to be the same.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The user currently gets an EBUSY error when attempting to set
the mac address on a macvlan device to the same value.
This should really be a no-op as nothing changes. Catch
the condition and return early.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a flag to indicate if a queue is rate-limited. Test the flag in
NAPI poll handler and avoid rescheduling the queue if true, otherwise
we risk locking up the host. The rescheduling will be done in the
timer callback function.
Reported-by: Jean-Louis Dupond <jean-louis@dupond.be>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Tested-by: Jean-Louis Dupond <jean-louis@dupond.be>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are number of problems with configuration peer
network device in absence of IFLA_VETH_PEER attributes
where attributes for main network device shared with
peer.
First it is not feasible to configure both network
devices with same MAC address since this makes
communication in such configuration problematic.
This case can be reproduced with following sequence:
# ip link add address 02:11:22:33:44:55 type veth
# ip li sh
...
26: veth0@veth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc \
noop state DOWN mode DEFAULT qlen 1000
link/ether 00:11:22:33:44:55 brd ff:ff:ff:ff:ff:ff
27: veth1@veth0: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc \
noop state DOWN mode DEFAULT qlen 1000
link/ether 00:11:22:33:44:55 brd ff:ff:ff:ff:ff:ff
Second it is not possible to register both main and
peer network devices with same name, that happens
when name for main interface is given with IFLA_IFNAME
and same attribute reused for peer.
This case can be reproduced with following sequence:
# ip link add dev veth1a type veth
RTNETLINK answers: File exists
To fix both of the cases check if corresponding netlink
attributes are taken from peer_tb when valid or
name based on rtnl ops kind and random address is used.
Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
