summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2019-11-19mdio_bus: Fix init if CONFIG_RESET_CONTROLLER=nGeert Uytterhoeven
Commit 1d4639567d97 ("mdio_bus: Fix PTR_ERR applied after initialization to constant") accidentally changed a check from -ENOTSUPP to -ENOSYS, causing failures if reset controller support is not enabled. E.g. on r7s72100/rskrza1: sh-eth e8203000.ethernet: MDIO init failed: -524 sh-eth: probe of e8203000.ethernet failed with error -524 Seen on r8a7740/armadillo, r7s72100/rskrza1, and r7s9210/rza2mevb. Fixes: 1d4639567d97 ("mdio_bus: Fix PTR_ERR applied after initialization to constant") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: YueHaibing <yuehaibing@huawei.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-19Revert "mdio_bus: fix mdio_register_device when RESET_CONTROLLER is disabled"David S. Miller
This reverts commit 075e238d12c21c8bde700d21fb48be7a3aa80194. Going to go with Geert's fix instead, which also has a correct Fixes tag. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-19net: hns3: fix a wrong reset interrupt status maskHuazhong Tan
According to hardware user manual, bits5~7 in register HCLGE_MISC_VECTOR_INT_STS means reset interrupts status, but HCLGE_RESET_INT_M is defined as bits0~2 now. So it will make hclge_reset_err_handle() read the wrong reset interrupt status. This patch fixes this wrong bit mask. Fixes: 2336f19d7892 ("net: hns3: check reset interrupt status when reset fails") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-19net: fec: fix clock count mis-matchChuhong Yuan
pm_runtime_put_autosuspend in probe will call runtime suspend to disable clks automatically if CONFIG_PM is defined. (If CONFIG_PM is not defined, its implementation will be empty, then runtime suspend will not be called.) Therefore, we can call pm_runtime_get_sync to runtime resume it first to enable clks, which matches the runtime suspend. (Only when CONFIG_PM is defined, otherwise pm_runtime_get_sync will also be empty, then runtime resume will not be called.) Then it is fine to disable clks without causing clock count mis-match. Fixes: c43eab3eddb4 ("net: fec: add missed clk_disable_unprepare in remove") Signed-off-by: Chuhong Yuan <hslester96@gmail.com> Acked-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-19net: phylink: fix link mode modification in PHY modeRussell King
Modifying the link settings via phylink_ethtool_ksettings_set() and phylink_ethtool_set_pauseparam() didn't always work as intended for PHY based setups, as calling phylink_mac_config() would result in the unresolved configuration being committed to the MAC, rather than the configuration with the speed and duplex setting. This would work fine if the update caused the link to renegotiate, but if no settings have changed, phylib won't trigger a renegotiation cycle, and the MAC will be left incorrectly configured. Avoid calling phylink_mac_config() unless we are using an inband mode in phylink_ethtool_ksettings_set(), and use phy_set_asym_pause() as introduced in 4.20 to set the PHY settings in phylink_ethtool_set_pauseparam(). Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-19net: phylink: update documentation on create and destroyRussell King
Update the documentation on phylink's create and destroy functions to explicitly state that the rtnl lock must not be held while calling these. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-19r8169: disable TSO on a single version of RTL8168c to fix performanceCorinna Vinschen
During performance testing, I found that one of my r8169 NICs suffered a major performance loss, a 8168c model. Running netperf's TCP_STREAM test didn't return the expected throughput of > 900 Mb/s, but rather only about 22 Mb/s. Strange enough, running the TCP_MAERTS and UDP_STREAM tests all returned with throughput > 900 Mb/s, as did TCP_STREAM with the other r8169 NICs I can test (either one of 8169s, 8168e, 8168f). Bisecting turned up commit 93681cd7d94f83903cb3f0f95433d10c28a7e9a5, "r8169: enable HW csum and TSO" as the culprit. I added my 8168c version, RTL_GIGA_MAC_VER_22, to the code special-casing the 8168evl as per the patch below. This fixed the performance problem for me. Fixes: 93681cd7d94f ("r8169: enable HW csum and TSO") Signed-off-by: Corinna Vinschen <vinschen@redhat.com> Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-19gve: fix dma sync bug where not all pages syncedAdi Suresh
The previous commit had a bug where the last page in the memory range could not be synced. This change fixes the behavior so that all the required pages are synced. Fixes: 9cfeeb576d49 ("gve: Fixes DMA synchronization") Signed-off-by: Adi Suresh <adisuresh@google.com> Reviewed-by: Catherine Sullivan <csully@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-18mdio_bus: fix mdio_register_device when RESET_CONTROLLER is disabledMarek Behún
When CONFIG_RESET_CONTROLLER is disabled, the devm_reset_control_get_exclusive function returns -ENOTSUPP. This is not handled in subsequent check and then the mdio device fails to probe. When CONFIG_RESET_CONTROLLER is enabled, its code checks in OF for reset device, and since it is not present, returns -ENOENT. -ENOENT is handled. Add -ENOTSUPP also. This happened to me when upgrading kernel on Turris Omnia. You either have to enable CONFIG_RESET_CONTROLLER or use this patch. Signed-off-by: Marek Behún <marek.behun@nic.cz> Fixes: 71dd6c0dff51b ("net: phy: add support for reset-controller") Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-18phy: mdio-sun4i: add missed regulator_disable in removeChuhong Yuan
The driver forgets to disable the regulator in remove like what is done in probe failure. Add the missed call to fix it. Signed-off-by: Chuhong Yuan <hslester96@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-18net/mlx4_en: Fix wrong limitation for number of TX ringsTariq Toukan
XDP_TX rings should not be limited by max_num_tx_rings_p_up. To make sure total number of TX rings never exceed MAX_TX_RINGS, add similar check in mlx4_en_alloc_tx_queue_per_tc(), where a new value is assigned for num_up. Fixes: 7e1dc5e926d5 ("net/mlx4_en: Limit the number of TX rings") Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-18mlxsw: spectrum_router: Fix determining underlay for a GRE tunnelPetr Machata
The helper mlxsw_sp_ipip_dev_ul_tb_id() determines the underlay VRF of a GRE tunnel. For a tunnel without a bound device, it uses the same VRF that the tunnel is in. However in Linux, a GRE tunnel without a bound device uses the main VRF as the underlay. Fix the function accordingly. mlxsw further assumed that moving a tunnel to a different VRF could cause conflict in local tunnel endpoint address, which cannot be offloaded. However, the only way that an underlay could be changed by moving the tunnel device itself is if the tunnel device does not have a bound device. But in that case the underlay is always the main VRF, so there is no opportunity to introduce a conflict by moving such device. Thus this check constitutes a dead code, and can be removed, which do. Fixes: 6ddb7426a7d4 ("mlxsw: spectrum_router: Introduce loopback RIFs") Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-17net/mlx4_en: fix mlx4 ethtool -N insertionLuigi Rizzo
ethtool expects ETHTOOL_GRXCLSRLALL to set ethtool_rxnfc->data with the total number of entries in the rx classifier table. Surprisingly, mlx4 is missing this part (in principle ethtool could still move forward and try the insert). Tested: compiled and run command: phh13:~# ethtool -N eth1 flow-type udp4 queue 4 Added rule with ID 255 Signed-off-by: Luigi Rizzo <lrizzo@google.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
2019-11-16net: hns3: cleanup of stray struct hns3_link_mode_mappingSalil Mehta
This patch cleans-up the stray left over code. It has no functionality impact. Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-16net: gemini: add missed free_netdevChuhong Yuan
This driver forgets to free allocated netdev in remove like what is done in probe failure. Add the free to fix it. Signed-off-by: Chuhong Yuan <hslester96@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-16net: stmmac: Use the correct style for SPDX License IdentifierNishad Kamdar
This patch corrects the SPDX License Identifier style in header files related to STMicroelectronics based Multi-Gigabit Ethernet driver. For C header files Documentation/process/license-rules.rst mandates C-like comments (opposed to C source files where C++ style should be used). Changes made by using a script provided by Joe Perches here: https://lkml.org/lkml/2019/2/7/46. Suggested-by: Joe Perches <joe@perches.com> Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-16octeontx2-af: Use the correct style for SPDX License IdentifierNishad Kamdar
This patch corrects the SPDX License Identifier style in header files related to Marvell OcteonTX2 network devices. It uses an expilict block comment for the SPDX License Identifier. Changes made by using a script provided by Joe Perches here: https://lkml.org/lkml/2019/2/7/46. Suggested-by: Joe Perches <joe@perches.com> Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-15mlx5: Reject requests to enable time stamping on both edges.Richard Cochran
This driver enables rising edge or falling edge, but not both, and so this patch validates that the request contains only one of the two edges. Signed-off-by: Richard Cochran <richardcochran@gmail.com> Reviewed-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-15igb: Reject requests that fail to enable time stamping on both edges.Richard Cochran
This hardware always time stamps rising and falling edges, and so this patch validates that the request does contains both edges. Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-15dp83640: Reject requests to enable time stamping on both edges.Richard Cochran
This driver enables rising edge or falling edge, but not both, and so this patch validates that the request contains only one of the two edges. Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-15mv88e6xxx: Reject requests to enable time stamping on both edges.Richard Cochran
This driver enables rising edge or falling edge, but not both, and so this patch validates that the request contains only one of the two edges. Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-15ptp: Introduce strict checking of external time stamp options.Richard Cochran
User space may request time stamps on rising edges, falling edges, or both. However, the particular mode may or may not be supported in the hardware or in the driver. This patch adds a "strict" flag that tells drivers to ensure that the requested mode will be honored. Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-15renesas: reject unsupported external timestamp flagsJacob Keller
Fix the renesas PTP support to explicitly reject any future flags that get added to the external timestamp request ioctl. In order to maintain currently functioning code, this patch accepts all three current flags. This is because the PTP_RISING_EDGE and PTP_FALLING_EDGE flags have unclear semantics and each driver seems to have interpreted them slightly differently. Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Richard Cochran <richardcochran@gmail.com> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-15mlx5: reject unsupported external timestamp flagsJacob Keller
Fix the mlx5 core PTP support to explicitly reject any future flags that get added to the external timestamp request ioctl. In order to maintain currently functioning code, this patch accepts all three current flags. This is because the PTP_RISING_EDGE and PTP_FALLING_EDGE flags have unclear semantics and each driver seems to have interpreted them slightly differently. [ RC: I'm not 100% sure what this driver does, but if I'm not wrong it follows the dp83640: flags Meaning ---------------------------------------------------- -------------------------- PTP_ENABLE_FEATURE Time stamp rising edge PTP_ENABLE_FEATURE|PTP_RISING_EDGE Time stamp rising edge PTP_ENABLE_FEATURE|PTP_FALLING_EDGE Time stamp falling edge PTP_ENABLE_FEATURE|PTP_RISING_EDGE|PTP_FALLING_EDGE Time stamp falling edge ] Cc: Feras Daoud <ferasda@mellanox.com> Cc: Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Richard Cochran <richardcochran@gmail.com> Reviewed-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-15igb: reject unsupported external timestamp flagsJacob Keller
Fix the igb PTP support to explicitly reject any future flags that get added to the external timestamp request ioctl. In order to maintain currently functioning code, this patch accepts all three current flags. This is because the PTP_RISING_EDGE and PTP_FALLING_EDGE flags have unclear semantics and each driver seems to have interpreted them slightly differently. This HW always time stamps both edges: flags Meaning ---------------------------------------------------- -------------------------- PTP_ENABLE_FEATURE Time stamp both edges PTP_ENABLE_FEATURE|PTP_RISING_EDGE Time stamp both edges PTP_ENABLE_FEATURE|PTP_FALLING_EDGE Time stamp both edges PTP_ENABLE_FEATURE|PTP_RISING_EDGE|PTP_FALLING_EDGE Time stamp both edges Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-15dp83640: reject unsupported external timestamp flagsJacob Keller
Fix the dp83640 PTP support to explicitly reject any future flags that get added to the external timestamp request ioctl. In order to maintain currently functioning code, this patch accepts all three current flags. This is because the PTP_RISING_EDGE and PTP_FALLING_EDGE flags have unclear semantics and each driver seems to have interpreted them slightly differently. For the record, the semantics of this driver are: flags Meaning ---------------------------------------------------- -------------------------- PTP_ENABLE_FEATURE Time stamp rising edge PTP_ENABLE_FEATURE|PTP_RISING_EDGE Time stamp rising edge PTP_ENABLE_FEATURE|PTP_FALLING_EDGE Time stamp falling edge PTP_ENABLE_FEATURE|PTP_RISING_EDGE|PTP_FALLING_EDGE Time stamp falling edge Cc: Stefan Sørensen <stefan.sorensen@spectralink.com> Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-15mv88e6xxx: reject unsupported external timestamp flagsJacob Keller
Fix the mv88e6xxx PTP support to explicitly reject any future flags that get added to the external timestamp request ioctl. In order to maintain currently functioning code, this patch accepts all three current flags. This is because the PTP_RISING_EDGE and PTP_FALLING_EDGE flags have unclear semantics and each driver seems to have interpreted them slightly differently. For the record, the semantics of this driver are: flags Meaning ---------------------------------------------------- -------------------------- PTP_ENABLE_FEATURE Time stamp falling edge PTP_ENABLE_FEATURE|PTP_RISING_EDGE Time stamp rising edge PTP_ENABLE_FEATURE|PTP_FALLING_EDGE Time stamp falling edge PTP_ENABLE_FEATURE|PTP_RISING_EDGE|PTP_FALLING_EDGE Time stamp rising edge Cc: Brandon Streiff <brandon.streiff@ni.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-15net: reject PTP periodic output requests with unsupported flagsJacob Keller
Commit 823eb2a3c4c7 ("PTP: add support for one-shot output") introduced a new flag for the PTP periodic output request ioctl. This flag is not currently supported by any driver. Fix all drivers which implement the periodic output request ioctl to explicitly reject any request with flags they do not understand. This ensures that the driver does not accidentally misinterpret the PTP_PEROUT_ONE_SHOT flag, or any new flag introduced in the future. This is important for forward compatibility: if a new flag is introduced, the driver should reject requests to enable the flag until the driver has actually been modified to support the flag in question. Cc: Felipe Balbi <felipe.balbi@linux.intel.com> Cc: David S. Miller <davem@davemloft.net> Cc: Christopher Hall <christopher.s.hall@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Richard Cochran <richardcochran@gmail.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Reviewed-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-15net: ep93xx_eth: fix mismatch of request_mem_region in removeChuhong Yuan
The driver calls release_resource in remove to match request_mem_region in probe, which is incorrect. Fix it by using the right one, release_mem_region. Signed-off-by: Chuhong Yuan <hslester96@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-15ax88172a: fix information leak on short answersOliver Neukum
If a malicious device gives a short MAC it can elicit up to 5 bytes of leaked memory out of the driver. We need to check for ETH_ALEN instead. Reported-by: syzbot+a8d4acdad35e6bbca308@syzkaller.appspotmail.com Signed-off-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-14net: hns3: fix ETS bandwidth validation bugYonglong Liu
Some device only support 4 TCs, but the driver check the total bandwidth of 8 TCs, so may cause wrong configurations write to the hw. This patch uses hdev->tc_max to instead HNAE3_MAX_TC to fix it. Fixes: e432abfb99e5 ("net: hns3: add common validation in hclge_dcb") Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-14net: hns3: reallocate SSU' buffer size when pfc_en changesYunsheng Lin
When a TC's PFC is disabled or enabled, the RX private buffer for this TC need to be changed too, otherwise this may cause packet dropped problem. This patch fixes it by calling hclge_buffer_alloc to reallocate buffer when pfc_en changes. Fixes: cacde272dd00 ("net: hns3: Add hclge_dcb module for the support of DCB feature") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-14net: hns3: add compatible handling for MAC VLAN switch parameter configurationGuangbin Huang
Previously, hns3 driver just directly send specific setting bit and mask bits of MAC VLAN switch parameter to the firmware, it can not be compatible with the old firmware, because the old one ignores mask bits and covers all bits with new setting bits. So when running with old firmware, the communication between PF and VF will fail after resetting or configuring spoof check, since they will do the MAC VLAN switch parameter configuration. This patch fixes this problem by reading switch parameter firstly, then just modifies the corresponding bit and sends it to firmware. Fixes: dd2956eab104 ("net: hns3: not allow SSU loopback while execute ethtool -t dev") Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-14ravb: implement MTU change while device is upUlrich Hecht
Pre-allocates buffers sufficient for the maximum supported MTU (2026) in order to eliminate the possibility of resource exhaustion when changing the MTU while the device is up. Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-14Merge tag 'linux-can-fixes-for-5.4-20191114' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2019-11-14 here another pull request for net/master consisting of one patch (including my S-o-b). Jouni Hogander's patch fixes a memory leak found by the syzbot in the slcan driver's error path. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-14Merge tag 'wireless-drivers-2019-11-14' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers Kalle Valo says: ==================== wireless-drivers fixes for v5.4 Hopefully last fixes for v5.4, only one iwlwifi fix this time. iwlwifi * fix A-MSDU data corruption when using CCMP/GCMP ciphers ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-14slcan: Fix memory leak in error pathJouni Hogander
This patch is fixing memory leak reported by Syzkaller: BUG: memory leak unreferenced object 0xffff888067f65500 (size 4096): comm "syz-executor043", pid 454, jiffies 4294759719 (age 11.930s) hex dump (first 32 bytes): 73 6c 63 61 6e 30 00 00 00 00 00 00 00 00 00 00 slcan0.......... 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<00000000a06eec0d>] __kmalloc+0x18b/0x2c0 [<0000000083306e66>] kvmalloc_node+0x3a/0xc0 [<000000006ac27f87>] alloc_netdev_mqs+0x17a/0x1080 [<0000000061a996c9>] slcan_open+0x3ae/0x9a0 [<000000001226f0f9>] tty_ldisc_open.isra.1+0x76/0xc0 [<0000000019289631>] tty_set_ldisc+0x28c/0x5f0 [<000000004de5a617>] tty_ioctl+0x48d/0x1590 [<00000000daef496f>] do_vfs_ioctl+0x1c7/0x1510 [<0000000059068dbc>] ksys_ioctl+0x99/0xb0 [<000000009a6eb334>] __x64_sys_ioctl+0x78/0xb0 [<0000000053d0332e>] do_syscall_64+0x16f/0x580 [<0000000021b83b99>] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [<000000008ea75434>] 0xffffffffffffffff Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com> Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-11-13net: cdc_ncm: Signedness bug in cdc_ncm_set_dgram_size()Dan Carpenter
This code is supposed to test for negative error codes and partial reads, but because sizeof() is size_t (unsigned) type then negative error codes are type promoted to high positive values and the condition doesn't work as expected. Fixes: 332f989a3b00 ("CDC-NCM: handle incomplete transfer of MTU") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-13slip: Fix memory leak in slip_open error pathJouni Hogander
Driver/net/can/slcan.c is derived from slip.c. Memory leak was detected by Syzkaller in slcan. Same issue exists in slip.c and this patch is addressing the leak in slip.c. Here is the slcan memory leak trace reported by Syzkaller: BUG: memory leak unreferenced object 0xffff888067f65500 (size 4096): comm "syz-executor043", pid 454, jiffies 4294759719 (age 11.930s) hex dump (first 32 bytes): 73 6c 63 61 6e 30 00 00 00 00 00 00 00 00 00 00 slcan0.......... 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<00000000a06eec0d>] __kmalloc+0x18b/0x2c0 [<0000000083306e66>] kvmalloc_node+0x3a/0xc0 [<000000006ac27f87>] alloc_netdev_mqs+0x17a/0x1080 [<0000000061a996c9>] slcan_open+0x3ae/0x9a0 [<000000001226f0f9>] tty_ldisc_open.isra.1+0x76/0xc0 [<0000000019289631>] tty_set_ldisc+0x28c/0x5f0 [<000000004de5a617>] tty_ioctl+0x48d/0x1590 [<00000000daef496f>] do_vfs_ioctl+0x1c7/0x1510 [<0000000059068dbc>] ksys_ioctl+0x99/0xb0 [<000000009a6eb334>] __x64_sys_ioctl+0x78/0xb0 [<0000000053d0332e>] do_syscall_64+0x16f/0x580 [<0000000021b83b99>] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [<000000008ea75434>] 0xfffffffffffffff Cc: "David S. Miller" <davem@davemloft.net> Cc: Oliver Hartkopp <socketcan@hartkopp.net> Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com> Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-13net: usb: qmi_wwan: add support for Foxconn T77W968 LTE modulesAleksander Morgado
These are the Foxconn-branded variants of the Dell DW5821e modules, same USB layout as those. The QMI interface is exposed in USB configuration #1: P: Vendor=0489 ProdID=e0b4 Rev=03.18 S: Manufacturer=FII S: Product=T77W968 LTE S: SerialNumber=0123456789ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#=0x1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option Signed-off-by: Aleksander Morgado <aleksander@aleksander.es> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-12dpaa2-eth: free already allocated channels on probe deferIoana Ciornei
The setup_dpio() function tries to allocate a number of channels equal to the number of CPUs online. When there are not enough DPCON objects already probed, the function will return EPROBE_DEFER. When this happens, the already allocated channels are not freed. This results in the incapacity of properly probing the next time around. Fix this by freeing the channels on the error path. Fixes: d7f5a9d89a55 ("dpaa2-eth: defer probe on object allocate") Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-11mdio_bus: Fix PTR_ERR applied after initialization to constantYueHaibing
Fix coccinelle warning: ./drivers/net/phy/mdio_bus.c:67:5-12: ERROR: PTR_ERR applied after initialization to constant on line 62 ./drivers/net/phy/mdio_bus.c:68:5-12: ERROR: PTR_ERR applied after initialization to constant on line 62 Fix this by using IS_ERR before PTR_ERR Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: 71dd6c0dff51 ("net: phy: add support for reset-controller") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-11mlxsw: core: Enable devlink reload only on probeJiri Pirko
Call devlink enable only during probe time and avoid deadlock during reload. Reported-by: Shalom Toledo <shalomt@mellanox.com> Fixes: 5a508a254bed ("devlink: disallow reload operation during device cleanup") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Tested-by: Shalom Toledo <shalomt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-11net: ethernet: dwmac-sun8i: Use the correct function in exit pathCorentin Labbe
When PHY is not powered, the probe function fail and some resource are still unallocated. Furthermore some BUG happens: dwmac-sun8i 5020000.ethernet: EMAC reset timeout ------------[ cut here ]------------ kernel BUG at /linux-next/net/core/dev.c:9844! So let's use the right function (stmmac_pltfr_remove) in the error path. Fixes: 9f93ac8d4085 ("net-next: stmmac: Add dwmac-sun8i") Cc: <stable@vger.kernel.org> # v4.15+ Signed-off-by: Corentin Labbe <clabbe@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-09devlink: disallow reload operation during device cleanupJiri Pirko
There is a race between driver code that does setup/cleanup of device and devlink reload operation that in some drivers works with the same code. Use after free could we easily obtained by running: while true; do echo "0000:00:10.0" >/sys/bus/pci/drivers/mlxsw_spectrum2/bind devlink dev reload pci/0000:00:10.0 & echo "0000:00:10.0" >/sys/bus/pci/drivers/mlxsw_spectrum2/unbind done Fix this by enabling reload only after setup of device is complete and disabling it at the beginning of the cleanup process. Reported-by: Ido Schimmel <idosch@mellanox.com> Fixes: 2d8dc5bbf4e7 ("devlink: Add support for reload") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-08Merge branch '40GbE' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue Jeff Kirsher says: ==================== Intel Wired LAN Driver Fixes 2019-11-08 This series contains fixes to igb, igc, ixgbe, i40e, iavf and ice drivers. Colin Ian King fixes a potentially wrap-around counter in a for-loop. Nick fixes the default ITR values for the iavf driver to 50 usecs interval. Arkadiusz fixes 'ethtool -m' for X722 devices where the correct value cannot be obtained from the firmware, so add X722 to the check to ensure the wrong value is not returned. Jake fixes igb and igc drivers in their implementation of launch time support by declaring skb->tstamp value as ktime_t instead of s64. Magnus fixes ixgbe and i40e where the need_wakeup flag for transmit may not be set for AF_XDP sockets that are only used to send packets. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-08ixgbe: need_wakeup flag might not be set for TxMagnus Karlsson
The need_wakeup flag for Tx might not be set for AF_XDP sockets that are only used to send packets. This happens if there is at least one outstanding packet that has not been completed by the hardware and we get that corresponding completion (which will not generate an interrupt since interrupts are disabled in the napi poll loop) between the time we stopped processing the Tx completions and interrupts are enabled again. In this case, the need_wakeup flag will have been cleared at the end of the Tx completion processing as we believe we will get an interrupt from the outstanding completion at a later point in time. But if this completion interrupt occurs before interrupts are enable, we lose it and should at that point really have set the need_wakeup flag since there are no more outstanding completions that can generate an interrupt to continue the processing. When this happens, user space will see a Tx queue need_wakeup of 0 and skip issuing a syscall, which means will never get into the Tx processing again and we have a deadlock. This patch introduces a quick fix for this issue by just setting the need_wakeup flag for Tx to 1 all the time. I am working on a proper fix for this that will toggle the flag appropriately, but it is more challenging than I anticipated and I am afraid that this patch will not be completed before the merge window closes, therefore this easier fix for now. This fix has a negative performance impact in the range of 0% to 4%. Towards the higher end of the scale if you have driver and application on the same core and issue a lot of packets, and towards no negative impact if you use two cores, lower transmission speeds and/or a workload that also receives packets. Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-11-08i40e: need_wakeup flag might not be set for TxMagnus Karlsson
The need_wakeup flag for Tx might not be set for AF_XDP sockets that are only used to send packets. This happens if there is at least one outstanding packet that has not been completed by the hardware and we get that corresponding completion (which will not generate an interrupt since interrupts are disabled in the napi poll loop) between the time we stopped processing the Tx completions and interrupts are enabled again. In this case, the need_wakeup flag will have been cleared at the end of the Tx completion processing as we believe we will get an interrupt from the outstanding completion at a later point in time. But if this completion interrupt occurs before interrupts are enable, we lose it and should at that point really have set the need_wakeup flag since there are no more outstanding completions that can generate an interrupt to continue the processing. When this happens, user space will see a Tx queue need_wakeup of 0 and skip issuing a syscall, which means will never get into the Tx processing again and we have a deadlock. This patch introduces a quick fix for this issue by just setting the need_wakeup flag for Tx to 1 all the time. I am working on a proper fix for this that will toggle the flag appropriately, but it is more challenging than I anticipated and I am afraid that this patch will not be completed before the merge window closes, therefore this easier fix for now. This fix has a negative performance impact in the range of 0% to 4%. Towards the higher end of the scale if you have driver and application on the same core and issue a lot of packets, and towards no negative impact if you use two cores, lower transmission speeds and/or a workload that also receives packets. Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-11-08igb/igc: use ktime accessors for skb->tstampJacob Keller
When implementing launch time support in the igb and igc drivers, the skb->tstamp value is assumed to be a s64, but it's declared as a ktime_t value. Although ktime_t is typedef'd to s64 it wasn't always, and the kernel provides accessors for ktime_t values. Use the ktime_to_timespec64 and ktime_set accessors instead of directly assuming that the variable is always an s64. This improves portability if the code is ever moved to another kernel version, or if the definition of ktime_t ever changes again in the future. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-11-08i40e: Fix for ethtool -m issue on X722 NICArkadiusz Kubalewski
This patch contains fix for a problem with command: 'ethtool -m <dev>' which breaks functionality of: 'ethtool <dev>' when called on X722 NIC Disallowed update of link phy_types on X722 NIC Currently correct value cannot be obtained from FW Previously wrong value returned by FW was used and was a root cause for incorrect output of 'ethtool <dev>' command Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
generated by cgit (git 2.34.1) at 2024-06-07 15:45:13 +0000