| Age | Commit message (Collapse) | Author |
|---|
|
Add missing ~ to the usage of the mask.
Reported-by: Kevin Benson <Kevin.Benson@zii.aero>
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 5c74c54ce6ff ("net: dsa: mv88e6xxx: Split monitor port configuration")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During initialization the driver issues a reset to the device and waits
for 100ms before checking if the firmware is ready. The waiting is
necessary because before that the device is irresponsive and the first
read can result in a completion timeout.
While 100ms is sufficient for Spectrum-1 and Spectrum-2, it is
insufficient for Spectrum-3.
Fix this by increasing the timeout to 200ms.
Fixes: da382875c616 ("mlxsw: spectrum: Extend to support Spectrum-3 ASIC")
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can't just use the top bits of the last sync event as they could be
off-by-one every 65,536 seconds, giving an error in reconstruction of
65,536 seconds.
This patch uses the difference in the bottom 16 bits (mod 2^16) to
calculate an offset that needs to be applied to the last sync event to
get to the current time.
Signed-off-by: Alexandru-Mihai Maftei <amaftei@solarflare.com>
Acked-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Packet forwarding is not working in rmnet bridge mode.
Because when a packet is forwarded, skb_push() for an ethernet header
is needed. But it doesn't call skb_push().
So, the ethernet header will be lost.
Test commands:
modprobe rmnet
ip netns add nst
ip netns add nst2
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link set veth1 netns nst
ip link set veth3 netns nst2
ip link add rmnet0 link veth0 type rmnet mux_id 1
ip link set veth2 master rmnet0
ip link set veth0 up
ip link set veth2 up
ip link set rmnet0 up
ip a a 192.168.100.1/24 dev rmnet0
ip netns exec nst ip link set veth1 up
ip netns exec nst ip a a 192.168.100.2/24 dev veth1
ip netns exec nst2 ip link set veth3 up
ip netns exec nst2 ip a a 192.168.100.3/24 dev veth3
ip netns exec nst2 ping 192.168.100.2
Fixes: 60d58f971c10 ("net: qualcomm: rmnet: Implement bridge mode")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to attach a bridge interface to the rmnet interface,
"master" operation is used.
(e.g. ip link set dummy1 master rmnet0)
But, in the rmnet_add_bridge(), which is a callback of ->ndo_add_slave()
doesn't register lower interface.
So, ->ndo_del_slave() doesn't work.
There are other problems too.
1. It couldn't detect circular upper/lower interface relationship.
2. It couldn't prevent stack overflow because of too deep depth
of upper/lower interface
3. It doesn't check the number of lower interfaces.
4. Panics because of several reasons.
The root problem of these issues is actually the same.
So, in this patch, these all problems will be fixed.
Test commands:
modprobe rmnet
ip link add dummy0 type dummy
ip link add rmnet0 link dummy0 type rmnet mux_id 1
ip link add dummy1 master rmnet0 type dummy
ip link add dummy2 master rmnet0 type dummy
ip link del rmnet0
ip link del dummy2
ip link del dummy1
Splat looks like:
[ 41.867595][ T1164] general protection fault, probably for non-canonical address 0xdffffc0000000101I
[ 41.869993][ T1164] KASAN: null-ptr-deref in range [0x0000000000000808-0x000000000000080f]
[ 41.872950][ T1164] CPU: 0 PID: 1164 Comm: ip Not tainted 5.6.0-rc1+ #447
[ 41.873915][ T1164] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 41.875161][ T1164] RIP: 0010:rmnet_unregister_bridge.isra.6+0x71/0xf0 [rmnet]
[ 41.876178][ T1164] Code: 48 89 ef 48 89 c6 5b 5d e9 fc fe ff ff e8 f7 f3 ff ff 48 8d b8 08 08 00 00 48 ba 00 7
[ 41.878925][ T1164] RSP: 0018:ffff8880c4d0f188 EFLAGS: 00010202
[ 41.879774][ T1164] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000101
[ 41.887689][ T1164] RDX: dffffc0000000000 RSI: ffffffffb8cf64f0 RDI: 0000000000000808
[ 41.888727][ T1164] RBP: ffff8880c40e4000 R08: ffffed101b3c0e3c R09: 0000000000000001
[ 41.889749][ T1164] R10: 0000000000000001 R11: ffffed101b3c0e3b R12: 1ffff110189a1e3c
[ 41.890783][ T1164] R13: ffff8880c4d0f200 R14: ffffffffb8d56160 R15: ffff8880ccc2c000
[ 41.891794][ T1164] FS: 00007f4300edc0c0(0000) GS:ffff8880d9c00000(0000) knlGS:0000000000000000
[ 41.892953][ T1164] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 41.893800][ T1164] CR2: 00007f43003bc8c0 CR3: 00000000ca53e001 CR4: 00000000000606f0
[ 41.894824][ T1164] Call Trace:
[ 41.895274][ T1164] ? rcu_is_watching+0x2c/0x80
[ 41.895895][ T1164] rmnet_config_notify_cb+0x1f7/0x590 [rmnet]
[ 41.896687][ T1164] ? rmnet_unregister_bridge.isra.6+0xf0/0xf0 [rmnet]
[ 41.897611][ T1164] ? rmnet_unregister_bridge.isra.6+0xf0/0xf0 [rmnet]
[ 41.898508][ T1164] ? __module_text_address+0x13/0x140
[ 41.899162][ T1164] notifier_call_chain+0x90/0x160
[ 41.899814][ T1164] rollback_registered_many+0x660/0xcf0
[ 41.900544][ T1164] ? netif_set_real_num_tx_queues+0x780/0x780
[ 41.901316][ T1164] ? __lock_acquire+0xdfe/0x3de0
[ 41.901958][ T1164] ? memset+0x1f/0x40
[ 41.902468][ T1164] ? __nla_validate_parse+0x98/0x1ab0
[ 41.903166][ T1164] unregister_netdevice_many.part.133+0x13/0x1b0
[ 41.903988][ T1164] rtnl_delete_link+0xbc/0x100
[ ... ]
Fixes: 60d58f971c10 ("net: qualcomm: rmnet: Implement bridge mode")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netdev_upper_dev_link() is useful to manage lower/upper interfaces.
And this function internally validates looping, maximum depth.
All or most virtual interfaces that could have a real interface
(e.g. macsec, macvlan, ipvlan etc.) use lower/upper infrastructure.
Test commands:
modprobe rmnet
ip link add dummy0 type dummy
ip link add rmnet1 link dummy0 type rmnet mux_id 1
for i in {2..100}
do
let A=$i-1
ip link add rmnet$i link rmnet$A type rmnet mux_id $i
done
ip link del dummy0
The purpose of the test commands is to make stack overflow.
Splat looks like:
[ 52.411438][ T1395] BUG: KASAN: slab-out-of-bounds in find_busiest_group+0x27e/0x2c00
[ 52.413218][ T1395] Write of size 64 at addr ffff8880c774bde0 by task ip/1395
[ 52.414841][ T1395]
[ 52.430720][ T1395] CPU: 1 PID: 1395 Comm: ip Not tainted 5.6.0-rc1+ #447
[ 52.496511][ T1395] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 52.513597][ T1395] Call Trace:
[ 52.546516][ T1395]
[ 52.558773][ T1395] Allocated by task 3171537984:
[ 52.588290][ T1395] BUG: unable to handle page fault for address: ffffffffb999e260
[ 52.589311][ T1395] #PF: supervisor read access in kernel mode
[ 52.590529][ T1395] #PF: error_code(0x0000) - not-present page
[ 52.591374][ T1395] PGD d6818067 P4D d6818067 PUD d6819063 PMD 0
[ 52.592288][ T1395] Thread overran stack, or stack corrupted
[ 52.604980][ T1395] Oops: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[ 52.605856][ T1395] CPU: 1 PID: 1395 Comm: ip Not tainted 5.6.0-rc1+ #447
[ 52.611764][ T1395] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 52.621520][ T1395] RIP: 0010:stack_depot_fetch+0x10/0x30
[ 52.622296][ T1395] Code: ff e9 f9 fe ff ff 48 89 df e8 9c 1d 91 ff e9 ca fe ff ff cc cc cc cc cc cc cc 89 f8 0
[ 52.627887][ T1395] RSP: 0018:ffff8880c774bb60 EFLAGS: 00010006
[ 52.628735][ T1395] RAX: 00000000001f8880 RBX: ffff8880c774d140 RCX: 0000000000000000
[ 52.631773][ T1395] RDX: 000000000000001d RSI: ffff8880c774bb68 RDI: 0000000000003ff0
[ 52.649584][ T1395] RBP: ffffea00031dd200 R08: ffffed101b43e403 R09: ffffed101b43e403
[ 52.674857][ T1395] R10: 0000000000000001 R11: ffffed101b43e402 R12: ffff8880d900e5c0
[ 52.678257][ T1395] R13: ffff8880c774c000 R14: 0000000000000000 R15: dffffc0000000000
[ 52.694541][ T1395] FS: 00007fe867f6e0c0(0000) GS:ffff8880da000000(0000) knlGS:0000000000000000
[ 52.764039][ T1395] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 52.815008][ T1395] CR2: ffffffffb999e260 CR3: 00000000c26aa005 CR4: 00000000000606e0
[ 52.862312][ T1395] Call Trace:
[ 52.887133][ T1395] Modules linked in: dummy rmnet veth openvswitch nsh nf_conncount nf_nat nf_conntrack nf_dex
[ 52.936749][ T1395] CR2: ffffffffb999e260
[ 52.965695][ T1395] ---[ end trace 7e32ca99482dbb31 ]---
[ 52.966556][ T1395] RIP: 0010:stack_depot_fetch+0x10/0x30
[ 52.971083][ T1395] Code: ff e9 f9 fe ff ff 48 89 df e8 9c 1d 91 ff e9 ca fe ff ff cc cc cc cc cc cc cc 89 f8 0
[ 53.003650][ T1395] RSP: 0018:ffff8880c774bb60 EFLAGS: 00010006
[ 53.043183][ T1395] RAX: 00000000001f8880 RBX: ffff8880c774d140 RCX: 0000000000000000
[ 53.076480][ T1395] RDX: 000000000000001d RSI: ffff8880c774bb68 RDI: 0000000000003ff0
[ 53.093858][ T1395] RBP: ffffea00031dd200 R08: ffffed101b43e403 R09: ffffed101b43e403
[ 53.112795][ T1395] R10: 0000000000000001 R11: ffffed101b43e402 R12: ffff8880d900e5c0
[ 53.139837][ T1395] R13: ffff8880c774c000 R14: 0000000000000000 R15: dffffc0000000000
[ 53.141500][ T1395] FS: 00007fe867f6e0c0(0000) GS:ffff8880da000000(0000) knlGS:0000000000000000
[ 53.143343][ T1395] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 53.152007][ T1395] CR2: ffffffffb999e260 CR3: 00000000c26aa005 CR4: 00000000000606e0
[ 53.156459][ T1395] Kernel panic - not syncing: Fatal exception
[ 54.213570][ T1395] Shutting down cpus with NMI
[ 54.354112][ T1395] Kernel Offset: 0x33000000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0x)
[ 54.355687][ T1395] Rebooting in 5 seconds..
Fixes: b37f78f234bf ("net: qualcomm: rmnet: Fix crash on real dev unregistration")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Basically, duplicate mux id isn't be allowed.
So, the creation of rmnet will be failed if there is duplicate mux id
is existing.
But, changelink routine doesn't check duplicate mux id.
Test commands:
modprobe rmnet
ip link add dummy0 type dummy
ip link add rmnet0 link dummy0 type rmnet mux_id 1
ip link add rmnet1 link dummy0 type rmnet mux_id 2
ip link set rmnet1 type rmnet mux_id 1
Fixes: 23790ef12082 ("net: qualcomm: rmnet: Allow to configure flags for existing devices")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The notifier_call() of the slave interface removes rmnet interface with
unregister_netdevice_queue().
But, before calling unregister_netdevice_queue(), it acquires
rcu readlock.
In the RCU critical section, sleeping isn't be allowed.
But, unregister_netdevice_queue() internally calls synchronize_net(),
which would sleep.
So, suspicious RCU usage warning occurs.
Test commands:
modprobe rmnet
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link add rmnet0 link dummy0 type rmnet mux_id 1
ip link set dummy1 master rmnet0
ip link del dummy0
Splat looks like:
[ 79.639245][ T1195] =============================
[ 79.640134][ T1195] WARNING: suspicious RCU usage
[ 79.640852][ T1195] 5.6.0-rc1+ #447 Not tainted
[ 79.641657][ T1195] -----------------------------
[ 79.642472][ T1195] ./include/linux/rcupdate.h:273 Illegal context switch in RCU read-side critical section!
[ 79.644043][ T1195]
[ 79.644043][ T1195] other info that might help us debug this:
[ 79.644043][ T1195]
[ 79.645682][ T1195]
[ 79.645682][ T1195] rcu_scheduler_active = 2, debug_locks = 1
[ 79.646980][ T1195] 2 locks held by ip/1195:
[ 79.647629][ T1195] #0: ffffffffa3cf64f0 (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x457/0x890
[ 79.649312][ T1195] #1: ffffffffa39256c0 (rcu_read_lock){....}, at: rmnet_config_notify_cb+0xf0/0x590 [rmnet]
[ 79.651717][ T1195]
[ 79.651717][ T1195] stack backtrace:
[ 79.652650][ T1195] CPU: 3 PID: 1195 Comm: ip Not tainted 5.6.0-rc1+ #447
[ 79.653702][ T1195] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 79.655037][ T1195] Call Trace:
[ 79.655560][ T1195] dump_stack+0x96/0xdb
[ 79.656252][ T1195] ___might_sleep+0x345/0x440
[ 79.656994][ T1195] synchronize_net+0x18/0x30
[ 79.661132][ T1195] netdev_rx_handler_unregister+0x40/0xb0
[ 79.666266][ T1195] rmnet_unregister_real_device+0x42/0xb0 [rmnet]
[ 79.667211][ T1195] rmnet_config_notify_cb+0x1f7/0x590 [rmnet]
[ 79.668121][ T1195] ? rmnet_unregister_bridge.isra.6+0xf0/0xf0 [rmnet]
[ 79.669166][ T1195] ? rmnet_unregister_bridge.isra.6+0xf0/0xf0 [rmnet]
[ 79.670286][ T1195] ? __module_text_address+0x13/0x140
[ 79.671139][ T1195] notifier_call_chain+0x90/0x160
[ 79.671973][ T1195] rollback_registered_many+0x660/0xcf0
[ 79.672893][ T1195] ? netif_set_real_num_tx_queues+0x780/0x780
[ 79.675091][ T1195] ? __lock_acquire+0xdfe/0x3de0
[ 79.675825][ T1195] ? memset+0x1f/0x40
[ 79.676367][ T1195] ? __nla_validate_parse+0x98/0x1ab0
[ 79.677290][ T1195] unregister_netdevice_many.part.133+0x13/0x1b0
[ 79.678163][ T1195] rtnl_delete_link+0xbc/0x100
[ ... ]
Fixes: ceed73a2cf4a ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rmnet_get_port() internally calls rcu_dereference_rtnl(),
which checks RTNL.
But rmnet_get_port() could be called by packet path.
The packet path is not protected by RTNL.
So, the suspicious RCU usage problem occurs.
Test commands:
modprobe rmnet
ip netns add nst
ip link add veth0 type veth peer name veth1
ip link set veth1 netns nst
ip link add rmnet0 link veth0 type rmnet mux_id 1
ip netns exec nst ip link add rmnet1 link veth1 type rmnet mux_id 1
ip netns exec nst ip link set veth1 up
ip netns exec nst ip link set rmnet1 up
ip netns exec nst ip a a 192.168.100.2/24 dev rmnet1
ip link set veth0 up
ip link set rmnet0 up
ip a a 192.168.100.1/24 dev rmnet0
ping 192.168.100.2
Splat looks like:
[ 146.630958][ T1174] WARNING: suspicious RCU usage
[ 146.631735][ T1174] 5.6.0-rc1+ #447 Not tainted
[ 146.632387][ T1174] -----------------------------
[ 146.633151][ T1174] drivers/net/ethernet/qualcomm/rmnet/rmnet_config.c:386 suspicious rcu_dereference_check() !
[ 146.634742][ T1174]
[ 146.634742][ T1174] other info that might help us debug this:
[ 146.634742][ T1174]
[ 146.645992][ T1174]
[ 146.645992][ T1174] rcu_scheduler_active = 2, debug_locks = 1
[ 146.646937][ T1174] 5 locks held by ping/1174:
[ 146.647609][ T1174] #0: ffff8880c31dea70 (sk_lock-AF_INET){+.+.}, at: raw_sendmsg+0xab8/0x2980
[ 146.662463][ T1174] #1: ffffffff93925660 (rcu_read_lock_bh){....}, at: ip_finish_output2+0x243/0x2150
[ 146.671696][ T1174] #2: ffffffff93925660 (rcu_read_lock_bh){....}, at: __dev_queue_xmit+0x213/0x2940
[ 146.673064][ T1174] #3: ffff8880c19ecd58 (&dev->qdisc_running_key#7){+...}, at: ip_finish_output2+0x714/0x2150
[ 146.690358][ T1174] #4: ffff8880c5796898 (&dev->qdisc_xmit_lock_key#3){+.-.}, at: sch_direct_xmit+0x1e2/0x1020
[ 146.699875][ T1174]
[ 146.699875][ T1174] stack backtrace:
[ 146.701091][ T1174] CPU: 0 PID: 1174 Comm: ping Not tainted 5.6.0-rc1+ #447
[ 146.705215][ T1174] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 146.706565][ T1174] Call Trace:
[ 146.707102][ T1174] dump_stack+0x96/0xdb
[ 146.708007][ T1174] rmnet_get_port.part.9+0x76/0x80 [rmnet]
[ 146.709233][ T1174] rmnet_egress_handler+0x107/0x420 [rmnet]
[ 146.710492][ T1174] ? sch_direct_xmit+0x1e2/0x1020
[ 146.716193][ T1174] rmnet_vnd_start_xmit+0x3d/0xa0 [rmnet]
[ 146.717012][ T1174] dev_hard_start_xmit+0x160/0x740
[ 146.717854][ T1174] sch_direct_xmit+0x265/0x1020
[ 146.718577][ T1174] ? register_lock_class+0x14d0/0x14d0
[ 146.719429][ T1174] ? dev_watchdog+0xac0/0xac0
[ 146.723738][ T1174] ? __dev_queue_xmit+0x15fd/0x2940
[ 146.724469][ T1174] ? lock_acquire+0x164/0x3b0
[ 146.725172][ T1174] __dev_queue_xmit+0x20c7/0x2940
[ ... ]
Fixes: ceed73a2cf4a ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the rmnet_changelink(), it uses IFLA_LINK without checking
NULL pointer.
tb[IFLA_LINK] could be NULL pointer.
So, NULL-ptr-deref could occur.
rmnet already has a lower interface (real_dev).
So, after this patch, rmnet_changelink() does not use IFLA_LINK anymore.
Test commands:
modprobe rmnet
ip link add dummy0 type dummy
ip link add rmnet0 link dummy0 type rmnet mux_id 1
ip link set rmnet0 type rmnet mux_id 2
Splat looks like:
[ 90.578726][ T1131] general protection fault, probably for non-canonical address 0xdffffc0000000000I
[ 90.581121][ T1131] KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
[ 90.582380][ T1131] CPU: 2 PID: 1131 Comm: ip Not tainted 5.6.0-rc1+ #447
[ 90.584285][ T1131] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 90.587506][ T1131] RIP: 0010:rmnet_changelink+0x5a/0x8a0 [rmnet]
[ 90.588546][ T1131] Code: 83 ec 20 48 c1 ea 03 80 3c 02 00 0f 85 6f 07 00 00 48 8b 5e 28 48 b8 00 00 00 00 00 0
[ 90.591447][ T1131] RSP: 0018:ffff8880ce78f1b8 EFLAGS: 00010247
[ 90.592329][ T1131] RAX: dffffc0000000000 RBX: 0000000000000000 RCX: ffff8880ce78f8b0
[ 90.593253][ T1131] RDX: 0000000000000000 RSI: ffff8880ce78f4a0 RDI: 0000000000000004
[ 90.594058][ T1131] RBP: ffff8880cf543e00 R08: 0000000000000002 R09: 0000000000000002
[ 90.594859][ T1131] R10: ffffffffc0586a40 R11: 0000000000000000 R12: ffff8880ca47c000
[ 90.595690][ T1131] R13: ffff8880ca47c000 R14: ffff8880cf545000 R15: 0000000000000000
[ 90.596553][ T1131] FS: 00007f21f6c7e0c0(0000) GS:ffff8880da400000(0000) knlGS:0000000000000000
[ 90.597504][ T1131] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 90.599418][ T1131] CR2: 0000556e413db458 CR3: 00000000c917a002 CR4: 00000000000606e0
[ 90.600289][ T1131] Call Trace:
[ 90.600631][ T1131] __rtnl_newlink+0x922/0x1270
[ 90.601194][ T1131] ? lock_downgrade+0x6e0/0x6e0
[ 90.601724][ T1131] ? rtnl_link_unregister+0x220/0x220
[ 90.602309][ T1131] ? lock_acquire+0x164/0x3b0
[ 90.602784][ T1131] ? is_bpf_image_address+0xff/0x1d0
[ 90.603331][ T1131] ? rtnl_newlink+0x4c/0x90
[ 90.603810][ T1131] ? kernel_text_address+0x111/0x140
[ 90.604419][ T1131] ? __kernel_text_address+0xe/0x30
[ 90.604981][ T1131] ? unwind_get_return_address+0x5f/0xa0
[ 90.605616][ T1131] ? create_prof_cpu_mask+0x20/0x20
[ 90.606304][ T1131] ? arch_stack_walk+0x83/0xb0
[ 90.606985][ T1131] ? stack_trace_save+0x82/0xb0
[ 90.607656][ T1131] ? stack_trace_consume_entry+0x160/0x160
[ 90.608503][ T1131] ? deactivate_slab.isra.78+0x2c5/0x800
[ 90.609336][ T1131] ? kasan_unpoison_shadow+0x30/0x40
[ 90.610096][ T1131] ? kmem_cache_alloc_trace+0x135/0x350
[ 90.610889][ T1131] ? rtnl_newlink+0x4c/0x90
[ 90.611512][ T1131] rtnl_newlink+0x65/0x90
[ ... ]
Fixes: 23790ef12082 ("net: qualcomm: rmnet: Allow to configure flags for existing devices")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rmnet registers IFLA_LINK interface as a lower interface.
But, IFLA_LINK could be NULL.
In the current code, rmnet doesn't check IFLA_LINK.
So, panic would occur.
Test commands:
modprobe rmnet
ip link add rmnet0 type rmnet mux_id 1
Splat looks like:
[ 36.826109][ T1115] general protection fault, probably for non-canonical address 0xdffffc0000000000I
[ 36.838817][ T1115] KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
[ 36.839908][ T1115] CPU: 1 PID: 1115 Comm: ip Not tainted 5.6.0-rc1+ #447
[ 36.840569][ T1115] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 36.841408][ T1115] RIP: 0010:rmnet_newlink+0x54/0x510 [rmnet]
[ 36.841986][ T1115] Code: 83 ec 18 48 c1 e9 03 80 3c 01 00 0f 85 d4 03 00 00 48 8b 6a 28 48 b8 00 00 00 00 00 c
[ 36.843923][ T1115] RSP: 0018:ffff8880b7e0f1c0 EFLAGS: 00010247
[ 36.844756][ T1115] RAX: dffffc0000000000 RBX: ffff8880d14cca00 RCX: 1ffff11016fc1e99
[ 36.845859][ T1115] RDX: 0000000000000000 RSI: ffff8880c3d04000 RDI: 0000000000000004
[ 36.846961][ T1115] RBP: 0000000000000000 R08: ffff8880b7e0f8b0 R09: ffff8880b6ac2d90
[ 36.848020][ T1115] R10: ffffffffc0589a40 R11: ffffed1016d585b7 R12: ffffffff88ceaf80
[ 36.848788][ T1115] R13: ffff8880c3d04000 R14: ffff8880b7e0f8b0 R15: ffff8880c3d04000
[ 36.849546][ T1115] FS: 00007f50ab3360c0(0000) GS:ffff8880da000000(0000) knlGS:0000000000000000
[ 36.851784][ T1115] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 36.852422][ T1115] CR2: 000055871afe5ab0 CR3: 00000000ae246001 CR4: 00000000000606e0
[ 36.853181][ T1115] Call Trace:
[ 36.853514][ T1115] __rtnl_newlink+0xbdb/0x1270
[ 36.853967][ T1115] ? lock_downgrade+0x6e0/0x6e0
[ 36.854420][ T1115] ? rtnl_link_unregister+0x220/0x220
[ 36.854936][ T1115] ? lock_acquire+0x164/0x3b0
[ 36.855376][ T1115] ? is_bpf_image_address+0xff/0x1d0
[ 36.855884][ T1115] ? rtnl_newlink+0x4c/0x90
[ 36.856304][ T1115] ? kernel_text_address+0x111/0x140
[ 36.856857][ T1115] ? __kernel_text_address+0xe/0x30
[ 36.857440][ T1115] ? unwind_get_return_address+0x5f/0xa0
[ 36.858063][ T1115] ? create_prof_cpu_mask+0x20/0x20
[ 36.858644][ T1115] ? arch_stack_walk+0x83/0xb0
[ 36.859171][ T1115] ? stack_trace_save+0x82/0xb0
[ 36.859710][ T1115] ? stack_trace_consume_entry+0x160/0x160
[ 36.860357][ T1115] ? deactivate_slab.isra.78+0x2c5/0x800
[ 36.860928][ T1115] ? kasan_unpoison_shadow+0x30/0x40
[ 36.861520][ T1115] ? kmem_cache_alloc_trace+0x135/0x350
[ 36.862125][ T1115] ? rtnl_newlink+0x4c/0x90
[ 36.864073][ T1115] rtnl_newlink+0x65/0x90
[ ... ]
Fixes: ceed73a2cf4a ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't attempt to interpret the PHY specific status register unless
the PHY is indicating that the resolution is valid.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current code causes problems when the unregistering netdevice could
be different then the registering one.
Since the check in mlx5_lag_netdev_event() does not allow any other
network namespace anyway, fix this by registerting the lag notifier
per init network namespace only.
Fixes: d48834f9d4b4 ("mlx5: Use dev_net netdevice notifier registrations")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Aya Levin <ayal@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
should use real receive queue number to configure hw rss
indirect table rather than maximal queue number
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
a reserved field is used to signify prime physical function index
in the latest firmware version, so we must assign a value to it
correctly
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
can not use a local variable as an input parameter of
irq_set_affinity_hint
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We cannot register the same netdev notifier multiple times when probing
stmmac devices. Register the notifier only once in module init, and also
make debugfs creation/deletion safe against simultaneous notifier call.
Fixes: 481a7d154cbb ("stmmac: debugfs entry name is not be changed when udev rename device name.")
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The firmware paths for the VSC8584 PHYs not not contain the leading
'microchip/' directory, as used in linux-firmware, resulting in an
error when probing the driver. This patch fixes it.
Fixes: a5afc1678044 ("net: phy: mscc: add support for VSC8584 PHY")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
genphy_c45_check_and_restart_aneg
When auto-negotiation is not required, return value should be zero.
Changes v1->v2:
- improved comments and code as Andrew Lunn and Heiner Kallweit suggestion
- fixed issue in genphy_c45_check_and_restart_aneg as Russell King
suggestion.
Fixes: 2a10ab043ac5 ("net: phy: add genphy_check_and_restart_aneg()")
Fixes: 1af9f16840e9 ("net: phy: add genphy_c45_check_and_restart_aneg()")
Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As the description before netdev_run_todo, we cannot call free_netdev
before rtnl_unlock, fix it by reorder the code.
Signed-off-by: yangerkun <yangerkun@huawei.com>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Outdated Raspberry Pi 4 firmware might configure the external PHY as
rgmii although the kernel currently sets it as rgmii-rxid. This makes
connections unreliable as ID_MODE_DIS is left enabled. To avoid this,
explicitly clear that bit whenever we don't need it.
Fixes: da38802211cc ("net: bcmgenet: Add RGMII_RXID support")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are still experiencing some packet loss with the existing advanced
congestion buffering (ACB) settings with the IMP port configured for
2Gb/sec, so revert to conservative link speeds that do not produce
packet loss until this is resolved.
Fixes: 8f1880cbe8d0 ("net: dsa: bcm_sf2: Configure IMP port for 2Gb/sec")
Fixes: de34d7084edd ("net: dsa: bcm_sf2: Only 7278 supports 2Gb/sec IMP port")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add missing newlines to netdev_* format strings so the lines
aren't buffered by the printk subsystem.
Nitpicked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SDMA engine used by TEMAC halts operation when it has finished
processing of the last buffer descriptor in the buffer ring.
Unfortunately, no interrupt event is generated when this happens,
so we need to setup another mechanism to make sure DMA operation is
restarted when enough buffers have been added to the ring.
Fixes: 92744989533c ("net: add Xilinx ll_temac device driver")
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Failures caused by GFP_ATOMIC memory pressure have been observed, and
due to the missing error handling, results in kernel crash such as
[1876998.350133] kernel BUG at mm/slub.c:3952!
[1876998.350141] invalid opcode: 0000 [#1] PREEMPT SMP PTI
[1876998.350147] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 5.3.0-scnxt #1
[1876998.350150] Hardware name: N/A N/A/COMe-bIP2, BIOS CCR2R920 03/01/2017
[1876998.350160] RIP: 0010:kfree+0x1ca/0x220
[1876998.350164] Code: 85 db 74 49 48 8b 95 68 01 00 00 48 31 c2 48 89 10 e9 d7 fe ff ff 49 8b 04 24 a9 00 00 01 00 75 0b 49 8b 44 24 08 a8 01 75 02 <0f> 0b 49 8b 04 24 31 f6 a9 00 00 01 00 74 06 41 0f b6 74 24
5b
[1876998.350172] RSP: 0018:ffffc900000f0df0 EFLAGS: 00010246
[1876998.350177] RAX: ffffea00027f0708 RBX: ffff888008d78000 RCX: 0000000000391372
[1876998.350181] RDX: 0000000000000000 RSI: ffffe8ffffd01400 RDI: ffff888008d78000
[1876998.350185] RBP: ffff8881185a5d00 R08: ffffc90000087dd8 R09: 000000000000280a
[1876998.350189] R10: 0000000000000002 R11: 0000000000000000 R12: ffffea0000235e00
[1876998.350193] R13: ffff8881185438a0 R14: 0000000000000000 R15: ffff888118543870
[1876998.350198] FS: 0000000000000000(0000) GS:ffff88811f300000(0000) knlGS:0000000000000000
[1876998.350203] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
s#1 Part1
[1876998.350206] CR2: 00007f8dac7b09f0 CR3: 000000011e20a006 CR4: 00000000001606e0
[1876998.350210] Call Trace:
[1876998.350215] <IRQ>
[1876998.350224] ? __netif_receive_skb_core+0x70a/0x920
[1876998.350229] kfree_skb+0x32/0xb0
[1876998.350234] __netif_receive_skb_core+0x70a/0x920
[1876998.350240] __netif_receive_skb_one_core+0x36/0x80
[1876998.350245] process_backlog+0x8b/0x150
[1876998.350250] net_rx_action+0xf7/0x340
[1876998.350255] __do_softirq+0x10f/0x353
[1876998.350262] irq_exit+0xb2/0xc0
[1876998.350265] do_IRQ+0x77/0xd0
[1876998.350271] common_interrupt+0xf/0xf
[1876998.350274] </IRQ>
In order to handle such failures more graceful, this change splits the
receive loop into one for consuming the received buffers, and one for
allocating new buffers.
When GFP_ATOMIC allocations fail, the receive will continue with the
buffers that is still there, and with the expectation that the allocations
will succeed in a later call to receive.
Fixes: 92744989533c ("net: add Xilinx ll_temac device driver")
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds error handling to the remaining dma_map_single() calls, so that
behavior is well defined if/when we run out of DMA memory.
Fixes: 92744989533c ("net: add Xilinx ll_temac device driver")
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is possible that the interrupt handler fires and frees up space in
the TX ring in between checking for sufficient TX ring space and
stopping the TX queue in temac_start_xmit. If this happens, the
queue wake from the interrupt handler will occur before the queue is
stopped, causing a lost wakeup and the adapter's transmit hanging.
To avoid this, after stopping the queue, check again whether there is
sufficient space in the TX ring. If so, wake up the queue again.
This is a port of the similar fix in axienet driver,
commit 7de44285c1f6 ("net: axienet: Fix race condition causing TX hang").
Fixes: 23ecc4bde21f ("net: ll_temac: fix checksum offload logic")
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is currently possible for a PHY device to be suspended as part of a
network device driver's suspend call while it is still being attached to
that net_device, either via phy_suspend() or implicitly via phy_stop().
Later on, when the MDIO bus controller get suspended, we would attempt
to suspend again the PHY because it is still attached to a network
device.
This is both a waste of time and creates an opportunity for improper
clock/power management bugs to creep in.
Fixes: 803dd9c77ac3 ("net: phy: avoid suspending twice a PHY")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The KS8851 requires that packet RX and TX are mutually exclusive.
Currently, the driver hopes to achieve this by disabling interrupt
from the card by writing the card registers and by disabling the
interrupt on the interrupt controller. This however is racy on SMP.
Replace this approach by expanding the spinlock used around the
ks_start_xmit() TX path to ks_irq() RX path to assure true mutual
exclusion and remove the interrupt enabling/disabling, which is
now not needed anymore. Furthermore, disable interrupts also in
ks_net_stop(), which was missing before.
Note that a massive improvement here would be to re-use the KS8851
driver approach, which is to move the TX path into a worker thread,
interrupt handling to threaded interrupt, and synchronize everything
with mutexes, but that would be a much bigger rework, for a separate
patch.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When netvsc_attach() is called by operations like changing MTU, etc.,
an extra wakeup may happen while netvsc_attach() calling
rndis_filter_device_add() which sends rndis messages when queue is
stopped in netvsc_detach(). The completion message will wake up queue 0.
We can reproduce the issue by changing MTU etc., then the wake_queue
counter from "ethtool -S" will increase beyond stop_queue counter:
stop_queue: 0
wake_queue: 1
The issue causes queue wake up, and counter increment, no other ill
effects in current code. So we didn't see any network problem for now.
To fix this, initialize tx_disable to true, and set it to false when
the NIC is ready to be attached or registered.
Fixes: 7b2ee50c0cd5 ("hv_netvsc: common detach logic")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
usbnet creates network interfaces with min_mtu = 0 and
max_mtu = ETH_MAX_MTU.
These values are not modified by qmi_wwan when the network interface
is created initially, allowing, for example, to set mtu greater than 1500.
When a raw_ip switch is done (raw_ip set to 'Y', then set to 'N') the mtu
values for the network interface are set through ether_setup, with
min_mtu = ETH_MIN_MTU and max_mtu = ETH_DATA_LEN, not allowing anymore to
set mtu greater than 1500 (error: mtu greater than device maximum).
The patch restores the original min/max mtu values set by usbnet after a
raw_ip switch.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If crashed kernel does not shutdown the NIC properly, PCIe FLR
is required in the kdump kernel in order to initialize all the
functions properly.
Fixes: d629522e1d66 ("bnxt_en: Reduce memory usage when running in kdump kernel.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Especially when bnxt_shutdown() is called during kexec, we need to
disable MSIX and disable Bus Master to completely quiesce the device.
Make these 2 calls unconditionally in the shutdown method.
Fixes: c20dc142dd7b ("bnxt_en: Disable bus master during PCI shutdown and driver unload.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While it is not yet understood why a TX underflow can easily occur
for SGMII interfaces resulting in a TX wedge. It has been found that
disabling/re-enabling the LMAC resolves the issue.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Robert Jones <rjones@gateworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The fw_status field is only 8 bits, so fix the read. Also,
we only want to look at the one status bit, to allow for future
use of the other bits, and watch for a bad PCI read.
Fixes: 97ca486592c0 ("ionic: add heartbeat check")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
at91ether_init was handling the phy mode and speed but since the switch to
phylink, the NCFGR register got overwritten by macb_mac_config(). The issue
is that the RM9200_RMII bit and the MACB_CLK_DIV32 field are cleared
but never restored as they conflict with the PAE, GBE and PCSSEL bits.
Add new capability to differentiate between EMAC and the other versions of
the IP and use it to set and avoid clearing the relevant bits.
Also, this fixes a NULL pointer dereference in macb_mac_link_up as the EMAC
doesn't use any rings/bufffers/queues.
Fixes: 7897b071ac3b ("net: macb: convert to phylink")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The configuration/command below is failing when the VF in the xml
file is already bound to the host iavf driver.
pci_0000_af_0_0.xml:
<interface type='hostdev' managed='yes'>
<source>
<address type='pci' domain='0x0000' bus='0xaf' slot='0x0' function='0x0'/>
</source>
<mac address='00:de:ad:00:11:01'/>
</interface>
> virsh attach-device domain_name pci_0000_af_0_0.xml
error: Failed to attach device from pci_0000_af_0_0.xml
error: Cannot set interface MAC/vlanid to 00:de:ad:00:11:01/0 for
ifname ens1f1 vf 0: Device or resource busy
This is failing because the VF has not been completely removed/reset
after being unbound (via the virsh command above) from the host iavf
driver and ice_set_vf_mac() checks if the VF is disabled before waiting
for the reset to finish.
Fix this by waiting for the VF remove/reset process to happen before
checking if the VF is disabled. Also, since many functions for VF
administration on the PF were more or less calling the same 3 functions
(ice_wait_on_vf_reset(), ice_is_vf_disabled(), and ice_check_vf_init())
move these into the helper function ice_check_vf_ready_for_cfg(). Then
call this function in any flow that attempts to configure/query a VF
from the PF.
Lastly, increase the maximum wait time in ice_wait_on_vf_reset() to
800ms, and modify/add the #define(s) that determine the wait time.
This was done for robustness because in rare/stress cases VF removal can
take a max of ~800ms and previously the wait was a max of ~300ms.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Remove code that tell the OS that link is going down when user
change flow control via ethtool. When link is up it isn't certain
that link goes down after 0x0605 aq command. If link doesn't go
down, OS thinks that link is down, but physical link is up. To
reset this state user have to take interface down and up.
If link goes down after 0x0605 command, FW send information
about that and after that driver tells the OS that the link goes
down. So this code in ethtool is unnecessary.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently if a user sets an odd [tx|rx]-usecs value through ethtool,
the request is denied because the hardware is set to have an ITR
granularity of 2us. This caused poor customer experience. Fix this by
aligning to a register allowed value, which results in rounding down.
Also, print a once per ring container type message to be clear about
our intentions.
Also, change the ITR_TO_REG define to be the bitwise and of the ITR
setting and the ICE_ITR_MASK. This makes the purpose of ITR_TO_REG more
obvious.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
On flow table creation, send the relevant flags according to what the FW
currently supports.
When FW doesn't support reformat option over SW-steering managed table,
the driver shouldn't pass this.
Fixes: 988fd6b32d07 ("net/mlx5: DR, Pass table flags at creation to lower layer")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The pool sizes represent the pool sizes in the fw. when we request
a pool size from fw, it will return the next possible group.
We track how many pools the fw has left and start requesting groups
from the big to the small.
When we start request 4k group, which doesn't exists in fw, fw
wants to allocate the next possible size, 64k, but will fail since
its exhausted. The correct smallest pool size in fw is 128 and not 4k.
Fixes: 39ac237ce009 ("net/mlx5: E-Switch, Refactor chains and priorities")
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
There is no need to reset all vf config (except link state) between
legacy and switchdev modes changes.
Also, set link state to AUTO, when legacy enabled.
Fixes: 3b83b6c2e024 ("net/mlx5e: Clear VF config when switching modes")
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Set vport gvmi in the tag, only when source gvmi is set in the bit mask.
Fixes: 26d688e3 ("net/mlx5: DR, Add Steering entry (STE) utilities")
Signed-off-by: Hamdan Igbaria <hamdani@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When health reporters are not supported, recovery function is invoked
directly, not via devlink health reporters.
In this direct flow, the recover function input parameter was passed
incorrectly and is causing a kernel oops. This patch is fixing the input
parameter.
Following call trace is observed on rx error health reporting.
Internal error: Oops: 96000007 [#1] PREEMPT SMP
Process kworker/u16:4 (pid: 4584, stack limit = 0x00000000c9e45703)
Call trace:
mlx5e_rx_reporter_err_rq_cqe_recover+0x30/0x164 [mlx5_core]
mlx5e_health_report+0x60/0x6c [mlx5_core]
mlx5e_reporter_rq_cqe_err+0x6c/0x90 [mlx5_core]
mlx5e_rq_err_cqe_work+0x20/0x2c [mlx5_core]
process_one_work+0x168/0x3d0
worker_thread+0x58/0x3d0
kthread+0x108/0x134
Fixes: c50de4af1d63 ("net/mlx5e: Generalize tx reporter's functionality")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Initialize RQ doorbell counters to zero prior to moving an RQ from RST
to RDY state. Per HW spec, when RQ is back to RDY state, the descriptor
ID on the completion is reset. The doorbell record must comply.
Fixes: 8276ea1353a4 ("net/mlx5e: Report and recover from CQE with error on RQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reported-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
rtnl_bridge_getlink is protected by rcu lock, so mlx5_eswitch_get_vepa
cannot take mutex lock. Two possible issues can happen:
1. User at the same time change vepa mode via RTM_SETLINK command.
2. User at the same time change the switchdev mode via devlink netlink
interface.
Case 1 cannot happen because rtnl executes one message in order.
Case 2 can happen but we do not expect user to change the switchdev mode
when changing vepa. Even if a user does it, so he will read a value
which is no longer valid.
Fixes: 8da202b24913 ("net/mlx5: E-Switch, Add support for VEPA in legacy mode.")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If an event is added while the rdma workqueue is being destroyed
it could lead to several races, list corruption, null pointer
dereference during queue_work or init_queue.
This fixes the race between the two flows which can occur during
shutdown.
A kref object and a completion object are added to the rdma_dev
structure, these are initialized before the workqueue is created.
The refcnt is used to indicate work is being added to the
workqueue and ensures the cleanup flow won't start while we're in
the middle of adding the event.
Once the work is added, the refcnt is decreased and the cleanup flow
is safe to run.
Fixes: cee9fbd8e2e ("qede: Add qedr framework")
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The reserved member should be named reserved3.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each extracted frame on Ocelot has an IFH. The frame and IFH are extracted
by reading chuncks of 4 bytes from a register.
In case the IFH and frames were read corretly it would try to read the next
frame. In case there are no more frames in the queue, it checks if there
were any previous errors and in that case clear the queue. But this check
will always succeed also when there are no errors. Because when extracting
the IFH the error is checked against 4(number of bytes read) and then the
error is set only if the extraction of the frame failed. So in a happy case
where there are no errors the err variable is still 4. So it could be
a case where after the check that there are no more frames in the queue, a
frame will arrive in the queue but because the error is not reseted, it
would try to flush the queue. So the frame will be lost.
The fix consist in resetting the error after reading the IFH.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
