summaryrefslogtreecommitdiff
path: root/drivers/nvme
AgeCommit message (Collapse)Author
2017-02-23nvme/pci: re-check security protocol support after resetScott Bauer
A device may change capabilities after each reset, e.g. due to a firmware upgrade. We should thus check for Security Send/Receive and OPAL support after each reset. Based on patches from Christoph and Keith. Signed-off-by: Scott Bauer <scott.bauer@intel.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-22nvme: detect NVMe controller in recent MacBooksDaniel Roschka
Adds support for detection of the NVMe controller found in the following recent MacBooks: - Retina MacBook 2016 (MacBook9,1) - 13" MacBook Pro 2016 without Touch Bar (MacBook13,1) - 13" MacBook Pro 2016 with Touch Bar (MacBook13,2) Signed-off-by: Daniel Roschka <danielroschka@phoenitydawn.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-22nvme-rdma: add support for host_traddrMax Gurtovoy
This will enable the user to control the specific interface for connection establishment in case the host has more than 1 interface under the same subnet. E.g: Host interfaces configured as: - ib0 1.1.1.1/16 - ib1 1.1.1.2/16 Target interfaces configured as: - ib0 1.1.1.3/16 (listener interface) - ib1 1.1.1.4/16 the following connect command will go through host iface ib0 (default): nvme connect -t rdma -n testsubsystem -a 1.1.1.3 -s 1023 but the following command will go through host iface ib1: nvme connect -t rdma -n testsubsystem -a 1.1.1.3 -s 1023 -w 1.1.1.2 Signed-off-by: Max Gurtovoy <maxg@mellanox.com> Reviewed-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-22nvmet-rdma: Fix error handlingChristophe JAILLET
According to the preceeding goto, it is likely that 'out_destroy_sq' was expected here. Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-22nvmet-rdma: use nvme cm status helperMax Gurtovoy
Also remove redundant debug prints. Signed-off-by: Max Gurtovoy <maxg@mellanox.com> Reviewed-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-22nvme-rdma: move nvme cm status helper to .h fileMax Gurtovoy
This will enable the usage for nvme rdma target. Also move from a lookup array to a switch statement. Signed-off-by: Max Gurtovoy <maxg@mellanox.com> Reviewed-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-22nvme-fc: don't bother to validate ioccsz and iorcszJames Smart
Discovery controllers don't set the values. They are in reserved areas of the Identify Controller data structure. Given the cmd completed, the minimal capsule sizes are supported, so no need to check nqn to detect discovery controllers and special case validations. Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-22nvme/pci: No special case for queue busy on IOKeith Busch
This driver previously required we have a special check for IO submitted to nvme IO queues that are temporarily suspended. That is no longer necessary since blk-mq provides a quiesce, so any IO that actually gets submitted to such a queue must be ended since the queue isn't going to start back up. This is fixing a condition where we have fewer IO queues after a controller reset. This may happen if the number of CPU's has changed, or controller firmware update changed the queue count, for example. While it may be possible to complete the IO on a different queue, the block layer does not provide a way to resubmit a request on a different hardware context once the request has entered the queue. We don't want these requests to be stuck indefinitely either, so ending them in error is our only option at the moment. Signed-off-by: Keith Busch <keith.busch@intel.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-22nvme/core: Fix race kicking freed request_queueKeith Busch
If a namespace has already been marked dead, we don't want to kick the request_queue again since we may have just freed it from another thread. Signed-off-by: Keith Busch <keith.busch@intel.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-22nvme/pci: Disable on removal when disconnectedKeith Busch
If the device is not present, the driver should disable the queues immediately. Prior to this, the driver was relying on the watchdog timer to kill the queues if requests were outstanding to the device, and that just delays removal up to one second. Signed-off-by: Keith Busch <keith.busch@intel.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-22nvme: Enable autonomous power state transitionsAndy Lutomirski
NVMe devices can advertise multiple power states. These states can be either "operational" (the device is fully functional but possibly slow) or "non-operational" (the device is asleep until woken up). Some devices can automatically enter a non-operational state when idle for a specified amount of time and then automatically wake back up when needed. The hardware configuration is a table. For each state, an entry in the table indicates the next deeper non-operational state, if any, to autonomously transition to and the idle time required before transitioning. This patch teaches the driver to program APST so that each successive non-operational state will be entered after an idle time equal to 100% of the total latency (entry plus exit) associated with that state. The maximum acceptable latency is controlled using dev_pm_qos (e.g. power/pm_qos_latency_tolerance_us in sysfs); non-operational states with total latency greater than this value will not be used. As a special case, setting the latency tolerance to 0 will disable APST entirely. On hardware without APST support, the sysfs file will not be exposed. The latency tolerance for newly-probed devices is set by the module parameter nvme_core.default_ps_max_latency_us. In theory, the device can expose "default" APST table, but this doesn't seem to function correctly on my device (Samsung 950), nor does it seem particularly useful. There is also an optional mechanism by which a configuration can be "saved" so it will be automatically loaded on reset. This can be configured from userspace, but it doesn't seem useful to support in the driver. On my laptop, enabling APST seems to save nearly 1W. The hardware tables can be decoded in userspace with nvme-cli. 'nvme id-ctrl /dev/nvmeN' will show the power state table and 'nvme get-feature -f 0x0c -H /dev/nvme0' will show the current APST configuration. This feature is quirked off on a known-buggy Samsung device. Signed-off-by: Andy Lutomirski <luto@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-22nvme: Add a quirk mechanism that uses identify_ctrlAndy Lutomirski
Currently, all NVMe quirks are based on PCI IDs. Add a mechanism to define quirks based on identify_ctrl's vendor id, model number, and/or firmware revision. Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Andy Lutomirski <luto@kernel.org> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-22nvme: make nvmf_register_transport require a create_ctrl callbackJohannes Thumshirn
nvmf_create_ctrl() relys on the presence of a create_crtl callback in the registered nvmf_transport_ops, so make nvmf_register_transport require one. Update the available call-sites as well to reflect these changes. Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-22nvme: Use CNS as 8-bit field and avoid endianness conversionParav Pandit
This patch defines CNS field as 8-bit field and avoids cpu_to/from_le conversions. Also initialize nvme_command cns value explicitly to NVME_ID_CNS_NS for readability (don't rely on the fact that NVME_ID_CNS_NS = 0). Reviewed-by: Max Gurtovoy <maxg@mellanox.com> Signed-off-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-22nvme: add semicolon in nvme_command settingMax Gurtovoy
Reviewed-by: Parav Pandit <parav@mellanox.com> Signed-off-by: Max Gurtovoy <maxg@mellanox.com> Reviewed-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-22nvmet: avoid dereferencing nvmet_reqMax Gurtovoy
No need to dereference req twice to get the cmd when we already have it stored in a local variable. Signed-off-by: Max Gurtovoy <maxg@mellanox.com> Reviewed-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-22nvme: Make controller state visible via sysfsSagi Grimberg
Easier for debugging and testing state machine transitions. Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-22nvmet: Make cntlid globally uniqueSagi Grimberg
We usually log the cntlid which is confusing in case we have multiple subsystems each with it's own cntlid ida. Instead make cntlid ida globally unique and log the initial association. Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Max Gurtovoy <maxg@mellanox.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-22nvmet_fc: cleanup of abort flag processing in fcp_op_doneJames Smart
Cleanup of abort flag processing in fcp_op_done. References were unnecessary Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-22nvme: admin-cmd: fix spelling mistake: "Counld" -> "Could"Colin Ian King
trivial fix to spelling mistake in pr_err message Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-17Merge branch 'for-4.11/next' into for-4.11/linus-mergeJens Axboe
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-17Merge branch 'for-4.11/block' into for-4.11/linus-mergeJens Axboe
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-17nvme: Check for Security send/recv support before issuing commands.Scott Bauer
We need to verify that the controller supports the security commands before actually trying to issue them. Signed-off-by: Scott Bauer <scott.bauer@intel.com> [hch: moved the check so that we don't call into the OPAL code if not supported] Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-17block/sed-opal: allocate struct opal_dev dynamicallyChristoph Hellwig
Insted of bloating the containing structure with it all the time this allocates struct opal_dev dynamically. Additionally this allows moving the definition of struct opal_dev into sed-opal.c. For this a new private data field is added to it that is passed to the send/receive callback. After that a lot of internals can be made private as well. Signed-off-by: Christoph Hellwig <hch@lst.de> Tested-by: Scott Bauer <scott.bauer@intel.com> Reviewed-by: Scott Bauer <scott.bauer@intel.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-14Move stack parameters for sed_ioctl to prevent oversized stack with CONFIG_KASANScott Bauer
When CONFIG_KASAN is enabled, compilation fails: block/sed-opal.c: In function 'sed_ioctl': block/sed-opal.c:2447:1: error: the frame size of 2256 bytes is larger than 2048 bytes [-Werror=frame-larger-than=] Moved all the ioctl structures off the stack and dynamically allocate using _IOC_SIZE() Fixes: 455a7b238cd6 ("block: Add Sed-opal library") Reported-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Scott Bauer <scott.bauer@intel.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-08nvme: support ranged discard requestsChristoph Hellwig
NVMe supports up to 256 ranges per DSM command, so wire up support for ranged discards up to that limit. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-06nvme: Add Support for Opal: Unlock from S3 & Opal Allocation/IoctlsScott Bauer
This patch implements the necessary logic to unlock an Opal enabled device coming back from an S3. The patch also implements the SED/Opal allocation necessary to support the opal ioctls. Signed-off-by: Scott Bauer <scott.bauer@intel.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-01-31block: fold cmd_type into the REQ_OP_ spaceChristoph Hellwig
Instead of keeping two levels of indirection for requests types, fold it all into the operations. The little caveat here is that previously cmd_type only applied to struct request, while the request and bio op fields were set to plain REQ_OP_READ/WRITE even for passthrough operations. Instead this patch adds new REQ_OP_* for SCSI passthrough and driver private requests, althought it has to add two for each so that we can communicate the data in/out nature of the request. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-01-31block: introduce blk_rq_is_passthroughChristoph Hellwig
This can be used to check for fs vs non-fs requests and basically removes all knowledge of BLOCK_PC specific from the block layer, as well as preparing for removing the cmd_type field in struct request. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-01-31nvme/pci: Don't mark IOD as aborted if abort wasn't sentKeith Busch
This patch sets the aborted flag only if an abort was sent, reducing excessive kernel message spamming for completed IO that wasn't actually aborted. Reported-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Keith Busch <keith.busch@intel.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-01-31lightnvm: use end_io callback instead of instanceMatias Bjørling
When the lightnvm core had the "gennvm" layer between the device and the target, there was a need for the core to be able to figure out which target it should send an end_io callback to. Leading to a "double" end_io, first for the media manager instance, and then for the target instance. Now that core and gennvm is merged, there is no longer a need for this, and a single end_io callback will do. Signed-off-by: Matias Bjørling <matias@cnexlabs.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-01-31lightnvm: add ioctls for vector I/OsMatias Bjørling
Enable user-space to issue vector I/O commands through ioctls. To issue a vector I/O, the ppa list with addresses is also required and must be mapped for the controller to access. For each ioctl, the result and status bits are returned as well, such that user-space can retrieve the open-channel SSD completion bits. The implementation covers the traditional use-cases of bad block management, and vectored read/write/erase. Signed-off-by: Matias Bjørling <matias@cnexlabs.com> Metadata implementation, test, and fixes. Signed-off-by: Simon A.F. Lund <slund@cnexlabs.com> Signed-off-by: Matias Bjørling <matias@cnexlabs.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-01-31lightnvm: reduce number of nvm_id groups to oneMatias Bjørling
The number of configuration groups has been limited to one in current code, even if there is support for up to four. With the introduction of the open-channel SSD 1.3 specification, only a single group is exposed onwards. Reflect this in the nvm_id structure. Signed-off-by: Matias Bjørling <matias@cnexlabs.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-01-31lightnvm: merge gennvm with coreMatias Bjørling
For the first iteration of Open-Channel SSDs, it was anticipated that there could be various media managers on top of an open-channel SSD, such to allow vendors to plug in their own host-side FTLs, without the media manager in between. Now that an Open-Channel SSD is exposed as a traditional block device, there is no longer a need for this. Therefore lets merge the gennvm code with core and simplify the stack. Signed-off-by: Matias Bjørling <matias@cnexlabs.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-01-30nvme/scsi: don't rely on BLK_MAX_CDBChristoph Hellwig
The NVMe SCSI emulation doesn't use BLOCK_PC requests, so BLK_MAX_CDB doesn't have a meaning for it. Instead opencode the value of 16 and refactor the code a bit so that related checks are next to each other and we only need to use the value in one place. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-01-29nvme: fix compilation of scsi componentJens Axboe
Since we moved the cdb parts and define out of the block proper, we need to include scsi/scsi_request.h for the nvme scsi layer. Fixes: 82ed4db499b8 ("block: split scsi_request out of struct request") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-01-27Merge branch 'for-4.11/block' into for-4.11/rq-refactorJens Axboe
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-01-26nvme-fc: use blk_rq_nr_phys_segmentsChristoph Hellwig
Without this deallocate won't work properly due to the mismatch of the bio/request size and the actual payload size. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: James Smart <james.smart@broadcom.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
2017-01-26nvmet-rdma: Fix missing dma sync to nvme data structuresParav Pandit
This patch performs dma sync operations on nvme_command and nvme_completion. nvme_command is synced (a) on receiving of the recv queue completion for cpu access. (b) before posting recv wqe back to rdma adapter for device access. nvme_completion is synced (a) on receiving of the recv queue completion of associated nvme_command for cpu access. (b) before posting send wqe to rdma adapter for device access. This patch is generated for git://git.infradead.org/nvme-fabrics.git Branch: nvmf-4.10 Signed-off-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
2017-01-26nvmet: Call fatal_error from keep-alive timout expirationSagi Grimberg
We only need to call delete_ctrl once, so given that both keep-alive timeout and any other fatal error can trigger it, just make sure we only call delete_ctrl once. Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Christoph Hellwig <hch@lst.de>
2017-01-26nvmet: cancel fatal error and flush async work before free controllerSagi Grimberg
Make sure they are not running and we can free the controller safely. Signed-off-by: Roy Shterman <roys@lightbitslabs.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Christoph Hellwig <hch@lst.de>
2017-01-26nvmet: delete controllers deletion upon subsystem releaseSagi Grimberg
No reason for them to be kept around if we are deleting the subsystem, so instead of passively wait for the host to disconnect, actively delete the controllers. Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Max Gurtovoy <maxg@mellanox.com> Reviewed-by: Christoph Hellwig <hch@lst.de>
2017-01-26nvmet_fc: correct logic in disconnect queue LS handlingJames Smart
Correct logic in disconnect queue LS handling. Rework so that queue searching and error reporting is above the section to send back a ls rjt Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
2017-01-17blk-mq-sched: allow setting of default IO schedulerJens Axboe
Add Kconfig entries to manage what devices get assigned an MQ scheduler, and add a blk-mq flag for drivers to opt out of scheduling. The latter is useful for admin type queues that still allocate a blk-mq queue and tag set, but aren't use for normal IO. Signed-off-by: Jens Axboe <axboe@fb.com> Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Omar Sandoval <osandov@fb.com>
2017-01-13nvme: use blk_rq_payload_bytesChristoph Hellwig
The new blk_rq_payload_bytes generalizes the payload length hacks that nvme_map_len did before. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-01-11nvme: apply DELAY_BEFORE_CHK_RDY quirk at probe time tooGuilherme G. Piccoli
Commit 54adc01055b7 ("nvme/quirk: Add a delay before checking for adapter readiness") introduced a quirk to adapters that cannot read the bit NVME_CSTS_RDY right after register NVME_REG_CC is set; these adapters need a delay or else the action of reading the bit NVME_CSTS_RDY could somehow corrupt adapter's registers state and it never recovers. When this quirk was added, we checked ctrl->tagset in order to avoid quirking in probe time, supposing we would never require such delay during probe. Well, it was too optimistic; we in fact need this quirk at probe time in some cases, like after a kexec. In some experiments, after abnormal shutdown of machine (aka power cord unplug), we booted into our bootloader in Power, which is a Linux kernel, and kexec'ed into another distro. If this kexec is too quick, we end up reaching the probe of NVMe adapter in that distro when adapter is in bad state (not fully initialized on our bootloader). What happens next is that nvme_wait_ready() is unable to complete, except if the quirk is enabled. So, this patch removes the original ctrl->tagset verification in order to enable the quirk even on probe time. Fixes: 54adc01055b7 ("nvme/quirk: Add a delay before checking for adapter readiness") Reported-by: Andrew Byrne <byrneadw@ie.ibm.com> Reported-by: Jaime A. H. Gomez <jahgomez@mx1.ibm.com> Reported-by: Zachary D. Myers <zdmyers@us.ibm.com> Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Acked-by: Jeffrey Lien <Jeff.Lien@wdc.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2017-01-11nvme-rdma: fix nvme_rdma_queue_is_readyChristoph Hellwig
Now that we don't abuse the cmd field in struct request for nvme command passthrough this function needs to be converted to the proper accessor as well. Fixes: d49187e97e ("nvme: introduce struct nvme_request") Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
2016-12-22Merge branch 'nvme-4.10' of git://git.infradead.org/nvme into for-linusJens Axboe
Christoph writes: The most significant one is that we've agreed on shared maintaince and a common repository for the PCIe NVMe driver and NVMe over Fabrics. The target code still only has a subset of the maintainers but goes through the same tree as well. Keith, Sagi and me will take turns at collecting patches and sending you pull requests.
2016-12-21nvmet/fcloop: remove some logically dead code performing redundant ret checksColin Ian King
The check to see if ret is non-zero and return this rather than count is redundant in two occassions. It is redundant because prior to this check, the return code ret is already checked for a non-zero error return value and we return from the function at that point. Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2016-12-21nvmet: fix KATO offset in Set FeaturesDaniel Verkamp
The Set Features implementation for Keep Alive Timer was using the wrong structure when retrieving the KATO value; it was treating the Set Features command as a Property Set command. The NVMe spec defines the Keep Alive Timer feature as having one input in CDW11 (4 bytes at offset 44 in the command) whereas the code was reading 8 bytes at offset 48. Since the Linux NVMe over Fabrics host never sets this feature, this code has presumably never been tested. Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
generated by cgit (git 2.34.1) at 2024-05-30 21:54:29 +0000