| Age | Commit message (Collapse) | Author |
|---|
|
The vim3l board does not work with a standard PCIe switch (ASM1184e),
spitting all kind of errors - hinting at HW misconfiguration (no link,
port enumeration issues, etc).
According to the the Synopsys DWC PCIe Reference Manual, in the section
dedicated to the PLCR register, bit 7 is described (FAST_LINK_MODE) as:
"Sets all internal timers to fast mode for simulation purposes."
it is sound to set this bit from a simulation perspective, but on actual
silicon, which expects timers to have a nominal value, it is not.
Make sure the FAST_LINK_MODE bit is cleared when configuring the RC
to solve this problem.
Link: https://lore.kernel.org/r/20200429164230.309922-1-maz@kernel.org
Fixes: 9c0ef6d34fdb ("PCI: amlogic: Add the Amlogic Meson PCIe controller driver")
Signed-off-by: Marc Zyngier <maz@kernel.org>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
|
|
Now that PCIE PHY has been introduced for AXG, the whole has_shared_phy
logic can be mutualized between AXG and G12A platforms.
This new PHY makes use of the shared MIPI/PCIE analog PHY found on AXG
platforms, which need to be used in order to have reliable PCIE
communications.
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add support for the Amlogic G12A SoC using a separate shared PHY.
This adds support for fetching a PHY phandle and call the PHY init,
reset and power on/off calls instead of writing in the PHY register or
toggling the PHY reset line.
The MIPI clock and the PHY memory resource are only required for the
Amlogic AXG SoC PCIe PHY setup, thus these elements are ignored for
the Amlogic G12A having a separate shared PHY.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
|
|
Fix the clock names used in the probe function according
to the bindings.
Fixes: 9c0ef6d34fdb ("PCI: amlogic: Add the Amlogic Meson PCIe controller driver")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
|
|
Normally asserting reset signal on gpio would be achieved with:
gpiod_set_value_cansleep(reset_gpio, 1);
Meson PCI driver set reset value to '0' instead of '1' as it takes into
account the PERST# signal polarity. The polarity should be taken care
in the device tree instead.
This fixes the reset assertion meaning and moves out the polarity
configuration in DT (please note that there is no DT currently using
this driver).
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Building the driver when GPIOLIB=n is not selected is causing the following
compilation failure:
drivers/pci/controller/dwc/pci-meson.c: In function 'meson_pcie_assert_reset':
drivers/pci/controller/dwc/pci-meson.c:290:2: error: implicit declaration of function 'gpiod_set_value_cansleep'; did you mean 'gpio_set_value_cansleep'? [-Werror=implicit-function-declaration]
gpiod_set_value_cansleep(mp->reset_gpio, 0);
^~~~~~~~~~~~~~~~~~~~~~~~
gpio_set_value_cansleep
drivers/pci/controller/dwc/pci-meson.c: In function 'meson_pcie_probe':
drivers/pci/controller/dwc/pci-meson.c:540:19: error: implicit declaration of function 'devm_gpiod_get'; did you mean 'devm_gpio_free'? [-Werror=implicit-function-declaration]
mp->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
^~~~~~~~~~~~~~
devm_gpio_free
drivers/pci/controller/dwc/pci-meson.c:540:48: error: 'GPIOD_OUT_LOW' undeclared (first use in this function); did you mean 'GPIOF_INIT_LOW'?
mp->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
^~~~~~~~~~~~~
GPIOF_INIT_LOW
Add the missing linux/gpio/consumer.h header to fix it.
Fixes: 9c0ef6d34fdb ("PCI: amlogic: Add the Amlogic Meson PCIe controller driver")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The Amlogic Meson PCIe host controller is based on the Synopsys DesignWare
PCI core. This patch adds the driver support for Meson PCIe controller.
Link: https://lore.kernel.org/linux-pci/20181218224708.GB22610@google.com/
Signed-off-by: Yue Wang <yue.wang@amlogic.com>
Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com>
[lorenzo.pieralisi@arm.com: updated coding/comment style]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
