| Age | Commit message (Collapse) | Author |
|---|
|
Move devm_pci_epc_create() to the beginning of dw_pcie_ep_init().
devm_pci_epc_create() is generic code that doesn't depend on any DWC
resource, so moving it earlier keeps all the subsequent devicetree-related
code together.
Link: https://lore.kernel.org/r/20250315201548.858189-9-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
|
|
The 'ranges' property of a PCI controller's parent can indicate address
translation information. Most system use 1:1 map between CPU physical and
PCI controller input addresses.
But some hardware, like i.MX8QXP, doesn't use 1:1 map. See below diagram:
┌─────────┐ ┌────────────┐
┌─────┐ │ │ IA: 0x8ff8_0000 │ │
│ CPU ├───►│ ┌────►├─────────────────┐ │ PCI │
└─────┘ │ │ │ IA: 0x8ff0_0000 │ │ │
CPU Addr │ │ ┌─►├─────────────┐ │ │ Controller │
0x7ff8_0000─┼───┘ │ │ │ │ │ │
│ │ │ │ │ │ │ PCI Addr
0x7ff0_0000─┼──────┘ │ │ └──► IOSpace ─┼────────────►
│ │ │ │ │ 0
0x7000_0000─┼────────►├─────────┐ │ │ │
└─────────┘ │ └──────► CfgSpace ─┼────────────►
Bus Fabric │ │ │ 0
│ │ │
└──────────► MemSpace ─┼────────────►
IA: 0x8000_0000 │ │ 0x8000_0000
└────────────┘
bus@5f000000 {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x80000000 0x0 0x70000000 0x10000000>;
pcie@5f010000 {
compatible = "fsl,imx8q-pcie";
reg = <0x5f010000 0x10000>, <0x8ff00000 0x80000>;
reg-names = "dbi", "config";
...
};
};
Intermediate address (IA) here means the PCIe controller input address.
The pcie@5f010000 'reg[config]' address is the parent bus (PCIe controller
input) address of CfgSpace.
The ATU in MemSpace is not explicitly described via devicetree, so we
assume the offset from CPU address to intermediate MemSpace address is the
same as that for CfgSpace.
We could use bus@5f000000 'ranges' for the same purpose.
Set parent_bus_offset using dw_pcie_init_parent_bus_offset(). The
parent_bus_offset is not used yet, so no functional change intended.
Link: https://lore.kernel.org/r/20250315201548.858189-8-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
dw_pcie_parent_bus_offset() looks up the parent bus address of a PCI
controller 'reg' property in devicetree. If implemented, .cpu_addr_fixup()
is a hard-coded way to get the parent bus address corresponding to a CPU
physical address.
Add debug code to compare the address from .cpu_addr_fixup() with the
address from devicetree. If they match, warn that .cpu_addr_fixup() is
redundant and should be removed; if they differ, warn that something is
wrong with the devicetree.
If .cpu_addr_fixup() is not implemented, the parent bus address should be
identical to the CPU physical address because we previously ignored the
parent bus address from devicetree. If the devicetree has a different
parent bus address, warn about it being broken.
[bhelgaas: split debug to separate patch for easier future revert, commit
log]
Link: https://lore.kernel.org/r/20250315201548.858189-7-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[bhelgaas: squash Ioana Ciornei <ioana.ciornei@nxp.com> fix for NULL
pointer deref when driver doesn't supply dw_pcie_ops, e.g., layerscape-pcie
https://lore.kernel.org/r/20250319134339.3114817-1-ioana.ciornei@nxp.com]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Return the offset from CPU physical address to the parent bus address of
the specified element of the devicetree 'reg' property.
[bhelgaas: cpu_phy_addr -> cpu_phys_addr, return offset, split
.cpu_addr_fixup() checking and debug to separate patch]
Link: https://lore.kernel.org/r/20250315201548.858189-6-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Update the CPM5 check to include CPM5_HOST1 variant. Previously, only
CPM5 was considered when mapping the "cpm_csr" register.
With this change, CPM5_HOST1 is also supported, ensuring proper
resource mapping for this variant.
Signed-off-by: Thippeswamy Havalige <thippeswamy.havalige@amd.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://lore.kernel.org/r/20250317124136.1317723-1-thippeswamy.havalige@amd.com
|
|
Don't populate the const read-only arrays "data" and "regs" on the
stack at run time, instead make them static.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
[kwilczynski: commit log, wrap overly long line to 80 columns]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://lore.kernel.org/r/20250317143456.477901-1-colin.i.king@gmail.com
|
|
Add support for AMD MDB (Multimedia DMA Bridge) IP core as Root Port.
The Versal2 devices include MDB Module. The integrated block for MDB
along with the integrated bridge can function as PCIe Root Port
controller at Gen5 32-GT/s operation per lane.
Bridge supports error and INTx interrupts and are handled using platform
specific interrupt line in Versal2.
Signed-off-by: Thippeswamy Havalige <thippeswamy.havalige@amd.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250228093351.923615-4-thippeswamy.havalige@amd.com
[bhelgaas: only present on ARM64-based SoCs; squash Kconfig dependency on
ARM64 from Geert Uytterhoeven <geert+renesas@glider.be>:
https://lore.kernel.org/r/eaef1dea7edcf146aa377d5e5c5c85a76ff56bae.1742306383.git.geert+renesas@glider.be]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
[kwilczynski: commit log, code comments and error messages clean-up,
drop redundant "depends on PCI" from Kconfig, expose the error code
as part of error messages where appropriatie, change "depends on"
expression to match existing style from other drivers]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
MSI remapping bypass (directly configuring MSI entries for devices on the
VMD bus) won't work under Xen, as Xen is not aware of devices in such bus,
and hence cannot configure the entries using the pIRQ interface in the PV
case, and in the PVH case traps won't be setup for MSI entries for such
devices.
Until Xen is aware of devices in the VMD bus prevent the
VMD_FEAT_CAN_BYPASS_MSI_REMAP capability from being used when running as
any kind of Xen guest.
The MSI remapping bypass is an optional feature of VMD bridges, and hence
when running under Xen it will be masked and devices will be forced to
redirect its interrupts from the VMD bridge. That mode of operation must
always be supported by VMD bridges and works when Xen is not aware of
devices behind the VMD bridge.
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Message-ID: <20250219092059.90850-3-roger.pau@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
The access to the PCI config space via pci_ops::read and pci_ops::write is
a low-level hardware access. The functions can be accessed with disabled
interrupts even on PREEMPT_RT. The pci_lock is a raw_spinlock_t for this
purpose.
A spinlock_t becomes a sleeping lock on PREEMPT_RT, so it cannot be
acquired with disabled interrupts. The vmd_dev::cfg_lock is accessed in
the same context as the pci_lock.
Make vmd_dev::cfg_lock a raw_spinlock_t type so it can be used with
interrupts disabled.
This was reported as:
BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48
Call Trace:
rt_spin_lock+0x4e/0x130
vmd_pci_read+0x8d/0x100 [vmd]
pci_user_read_config_byte+0x6f/0xe0
pci_read_config+0xfe/0x290
sysfs_kf_bin_read+0x68/0x90
Signed-off-by: Ryo Takakura <ryotkkr98@gmail.com>
Tested-by: Luis Claudio R. Goncalves <lgoncalv@redhat.com>
Acked-by: Luis Claudio R. Goncalves <lgoncalv@redhat.com>
[bigeasy: reword commit message]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-off-by: Luis Claudio R. Goncalves <lgoncalv@redhat.com>
Link: https://lore.kernel.org/r/20250218080830.ufw3IgyX@linutronix.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: add back report info from
https://lore.kernel.org/lkml/20241218115951.83062-1-ryotkkr98@gmail.com/]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Consolidate devicetree resource handling in dw_pcie_host_get_resources().
No functional change intended.
Link: https://lore.kernel.org/r/20250315201548.858189-5-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
|
|
Move devm_pci_alloc_host_bridge() to the beginning of dw_pcie_host_init().
devm_pci_alloc_host_bridge() is generic code that doesn't depend on any DWC
resource, so moving it earlier keeps all the subsequent devicetree-related
code together.
[bhelgaas: reorder earlier in series]
Link: https://lore.kernel.org/r/20250315201548.858189-4-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Rename 'cpu_addr' to 'parent_bus_addr' in the DesignWare ATU configuration.
The ATU translates parent bus addresses to PCI addresses, which are often
the same as CPU addresses but can differ in systems where the bus fabric
translates addresses before passing them to the PCIe controller. This
renaming clarifies the purpose and avoids confusion.
Link: https://lore.kernel.org/r/20250315201548.858189-3-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The msg_res region translates writes into PCIe Message TLPs. Previously we
mapped this region using atu.cpu_addr, the input address programmed into
the ATU.
"cpu_addr" is a misnomer because when a bus fabric translates addresses
between the CPU and the ATU, the ATU input address is different from the
CPU address. A future patch will rename "cpu_addr" and correct the value
to be the ATU input address instead of the CPU physical address.
Map the msg_res region before writing to it using the msg_res resource
start, a CPU physical address.
Link: https://lore.kernel.org/r/20250315201548.858189-2-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
If an error occurs after a successful phy_init() call, then phy_exit()
should be called.
Add the missing call, as already done in the remove function.
Fixes: bbd11bddb398 ("PCI: hisi: Add HiSilicon STB SoC PCIe controller driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
[kwilczynski: remove unnecessary hipcie->phy NULL check from
histb_pcie_probe() and squash a patch that removes similar NULL
check for hipcie-phy from histb_pcie_remove() from
https://lore.kernel.org/linux-pci/c369b5d25e17a44984ae5a889ccc28a59a0737f7.1742058005.git.christophe.jaillet@wanadoo.fr]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://lore.kernel.org/r/8301fc15cdea5d2dac21f57613e8e6922fb1ad95.1740854531.git.christophe.jaillet@wanadoo.fr
|
|
Use devm_clk_bulk_get_all() helper to simplify clock handle code.
No functional changes intended.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[kwilczynski: commit log, refactor to use dev_err_probe()]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20250226025628.1681206-1-hongxing.zhu@nxp.com
|
|
Instead of testing the controller register address to distinguish
controller 1 from controller 0 on i.MX8MQ platforms, use the PCI domain
number, which comes from the devicetree 'linux,pci-domain' property.
All relevant devicetrees should already supply 'linux,pci-domain', which
was added by c0b70f05c87f ("arm64: dts: imx8mq: use_dt_domains for pci
node").
Instead of being set directly in imx_pcie_probe(), pci->dbi_base will be
set by the DWC core in dw_pcie_get_resources().
No functional changes intended.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250226024256.1678103-3-hongxing.zhu@nxp.com
|
|
When running the RK3588 in Endpoint mode, with an Intel host with IOMMU
enabled, the host side prints:
DMAR: VT-d detected Invalidation Time-out Error: SID 0
When running the RK3588 in Endpoint mode, with an AMD host with IOMMU
enabled, the host side prints:
iommu ivhd0: AMD-Vi: Event logged [IOTLB_INV_TIMEOUT device=63:00.0 address=0x42b5b01a0]
Rockchip has confirmed that the ATS support for RK3588 only works when
running the PCIe controller in Root Complex (RC) mode, see:
https://lore.kernel.org/linux-pci/93cdce39-1ae6-4939-a3fc-db10be7564e5@rock-chips.com
Usually, to handle these issues, we add a quirk for the PCI vendor and
device ID in drivers/pci/quirks.c with quirk_no_ats(). That is because
we cannot usually modify the capabilities on the EP side. In this case,
we can modify the capabilities on the EP side.
Thus, hide the broken ATS capability on RK3588 when running in EP mode.
That way, we don't need any quirk on the host side, and we see no errors
on the host side, and we can run pci_endpoint_test successfully, with
the IOMMU enabled on the host side.
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
[kwilczynski: commit log, tidy up code comments and error message]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250310094826.842681-6-cassel@kernel.org
|
|
Add dw_pcie_ep_hide_ext_capability() which can be used by an endpoint
controller driver to hide a capability.
This can be useful to hide a capability that is buggy, such that the
host side does not try to enable the buggy capability.
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://lore.kernel.org/r/20250310094826.842681-5-cassel@kernel.org
|
|
If the bitmap or memory allocations fail, then dw_pcie_ep_init_registers()
will incorrectly return a success.
Return -ENOMEM instead.
Fixes: 869bc5253406 ("PCI: dwc: ep: Fix DBI access failure for drivers requiring refclk from host")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/36dcb6fc-f292-4dd5-bd45-a8c6f9dc3df7@stanley.mountain
|
|
Convert the code to use the new guard(msi_descs_lock).
No functional change intended.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/all/20250313130321.758905320@linutronix.de
|
|
The Versal Net ACAP (Adaptive Compute Acceleration Platform) devices
incorporate the Coherency and PCIe Gen5 Module, specifically the
Next-Generation Compact Module (CPM5NC).
The integrated CPM5NC block, along with the built-in bridge, can function
as a PCIe Root Port and supports the PCIe Gen5 protocol with data transfer
rates of up to 32 GT/s, and is capable of supporting up to a x16 lane-width
configuration.
Bridge errors are managed using a specific interrupt line designed for
CPM5N. The INTx interrupt support is not available.
Currently in this commit platform specific bridge errors support is not
added.
Signed-off-by: Thippeswamy Havalige <thippeswamy.havalige@amd.com>
[kwilczynski: commit log, squashed patch to fix an if-statement condition
to ensure that xilinx_cpm_pcie_init_port() does not run on the CPM5NC_HOST
variant from https://lore.kernel.org/linux-pci/20250311072402.1049990-1-thippeswamy.havalige@amd.com]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250224155025.782179-4-thippeswamy.havalige@amd.com
|
|
The IRQ domain allocated for the PCIe controller is not freed if
resource_list_first_type() returns NULL, leading to a resource leak.
This fix ensures properly cleaning up the allocated IRQ domain in
the error path.
Fixes: 49e427e6bdd1 ("Merge branch 'pci/host-probe-refactor'")
Signed-off-by: Thippeswamy Havalige <thippeswamy.havalige@amd.com>
[kwilczynski: added missing Fixes: tag, refactored to use one of the goto labels]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://lore.kernel.org/r/20250224155025.782179-2-thippeswamy.havalige@amd.com
|
|
Fix typos and whitespace errors.
Link: https://lore.kernel.org/r/20250307231715.438518-1-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Remove the superfluous function dw_pcie_ep_find_ext_capability(),
as it is virtually identical to dw_pcie_find_ext_capability().
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250221202646.395252-3-cassel@kernel.org
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
Looking at section "11.4.4.29 USP_PCIE_RESBAR Registers Summary" in the
Technical Reference Manual (TRM) for RK3588, we can see that none of the
BARs are Fixed BARs, but actually Resizable BARs.
I couldn't find any reference in the TRM for RK3568, but looking at the
downstream PCIe endpoint driver, both RK3568 and RK3588 are treated as
the same, so the BARs on RK3568 must also be Resizable BARs.
Now when we actually have support for Resizable BARs, let's configure
these BARs as such.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20250131182949.465530-16-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
The support for a specific iATU alignment was added in
commit 2a9a801620ef ("PCI: endpoint: Add support to specify alignment for
buffers allocated to BARs").
This commit specifically mentions both that the alignment by each DWC
based EP driver should match CX_ATU_MIN_REGION_SIZE, and that AM65x
specifically has a 64 KB alignment.
This also matches the CX_ATU_MIN_REGION_SIZE value specified in the
section "12.2.2.4.7 PCIe Subsystem Address Translation" of the Technical
Reference Manual (TRM) for AM65x:
https://www.ti.com/lit/ug/spruid7e/spruid7e.pdf
This higher value, 1 MB, was obviously an ugly hack used to be able to
handle Resizable BARs which have a minimum size of 1 MB.
Now when we actually have support for Resizable BARs, let's configure the
iATU alignment requirement to the actual requirement.
(BARs described as Resizable will still get aligned to 1 MB.)
Cc: stable+noautosel@kernel.org # Depends on PCI endpoint Resizable BARs series
Fixes: 23284ad677a9 ("PCI: keystone: Add support for PCIe EP in AM654x Platforms")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250131182949.465530-15-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
Looking at section "12.2.2.4.15 PCIe Subsystem BAR Configuration" in the
following Technical Reference Manual (TRM) for AM65x:
https://www.ti.com/lit/ug/spruid7e/spruid7e.pdf
We can see that BAR2 and BAR5 are not Fixed BARs, but actually Resizable
BARs.
Now when we actually have support for Resizable BARs, let's configure
these BARs as such.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20250131182949.465530-14-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
The DWC databook specifies three different BARn_SIZING_SCHEME_N as:
- Fixed Mask (0)
- Programmable Mask (1)
- Resizable BAR (2)
Each of these sizing schemes have different instructions for how to
initialize the BAR.
The DWC driver currently does not support resizable BARs.
Instead, in order to somewhat support resizable BARs, the DWC EP driver
currently has an ugly hack that force sets a resizable BAR to 1 MB, if
such a BAR is detected.
Additionally, this hack only works if the DWC glue driver also has lied
in their EPC features, and claimed that the resizable BAR is a 1 MB fixed
size BAR.
This is unintuitive (as you somehow need to know that you need to lie in
your EPC features), but other than that it is overly restrictive, since a
resizable BAR is capable of supporting sizes different than 1 MB.
Add proper support for resizable BARs in the DWC EP driver.
Note that the pci_epc_set_bar() API takes a struct pci_epf_bar which tells
the EPC driver how it wants to configure the BAR.
struct pci_epf_bar only has a single size struct member.
This means that an EPC driver will only be able to set a single supported
size. This is perfectly fine, as we do not need the complexity of allowing
a host to change the size of the BAR. If someone ever wants to support
resizing a resizable BAR, the pci_epc_set_bar() API can be extended in the
future.
With these changes, we allow an EPF driver to configure the size of
Resizable BARs, rather than forcing them to a 1 MB size.
This means that an EPC driver does not need to lie in EPC features, and an
EPF driver will be able to set an arbitrary size (not be forced to a 1 MB
size), just like BAR_PROGRAMMABLE.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250131182949.465530-13-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
Move dw_pcie_ep_find_ext_capability() so that it is located next to
dw_pcie_ep_find_capability().
Additionally, a follow-up commit requires this to be defined earlier
in order to avoid a forward declaration.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20250131182949.465530-12-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
Add PCIe Root Port controller support for the Agilex family of chips.
The Agilex PCIe Hard IP has three variants that are mostly software
compatible, except for a couple register offsets. The P-Tile variant
supports Gen3/Gen4 1x16. The F-Tile variant supports Gen3/Gen4 4x4,
4x8, and 4x16. The R-Tile variant improves on the F-Tile variant by
adding Gen5 support.
To simplify the implementation of pci_ops read/write functions,
ep_{read/write}_cfg() callbacks were added to struct altera_pci_ops
to easily distinguish between hardware variants.
Signed-off-by: D M, Sharath Kumar <sharath.kumar.d.m@intel.com>
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250221170452.875419-3-matthew.gerlach@linux.intel.com
[kwilczynski: tidy code comments]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
The for_each_available_child_of_node_scoped() helper provides
a scope-based clean-up functionality to put the device_node
automatically, and as such, there is no need to call of_node_put()
directly.
Thus, use this helper to simplify the code.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240831040413.126417-7-zhangzekun11@huawei.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
The for_each_available_child_of_node_scoped() helper provides
a scope-based clean-up functionality to put the device_node
automatically, and as such, there is no need to call of_node_put()
directly.
Thus, use this helper to simplify the code.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240831040413.126417-6-zhangzekun11@huawei.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
The for_each_available_child_of_node_scoped() helper provides
a scope-based clean-up functionality to put the device_node
automatically, and as such, there is no need to call of_node_put()
directly.
Thus, use this helper to simplify the code.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240831040413.126417-5-zhangzekun11@huawei.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
The for_each_available_child_of_node_scoped() helper provides
a scope-based clean-up functionality to put the device_node
automatically, and as such, there is no need to call of_node_put()
directly.
Thus, use this helper to simplify the code.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240831040413.126417-4-zhangzekun11@huawei.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
The combination of dev_err() and the returned error code could be
replaced by dev_err_probe() in driver's probe function.
Thus, convert the code to use dev_err_probe() to make code simpler.
Suggested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20240831040413.126417-3-zhangzekun11@huawei.com
[kwilczynski: commit log, return -ETIMEDOUT from hi3660_pcie_phy_start()
rather than -EINVAL for when the PIPE clock fails to become stable,
drop redundant dev->of_node NULL check]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
Move PCI_VENDOR_ID_ROCKCHIP from pci_endpoint_test.c to pci_ids.h and
reuse it in pcie-rockchip-host.c.
Link: https://lore.kernel.org/r/20250218092120.2322784-2-cassel@kernel.org
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
Add the debugfs property to provide a view of the current link's LTSSM
status from the Root Port device.
Signed-off-by: Hans Zhang <18255117159@163.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Niklas Cassel <cassel@kernel.org>
Tested-by: Hrishikesh Deleep <hrishikesh.d@samsung.com>
Link: https://lore.kernel.org/r/20250223141848.231232-1-18255117159@163.com
[kwilczynski: commit log, refactor dw_ltssm_sts_string() to avoid
compilation errors on platforms that do not set CONFIG_PCIE_DW_HOST]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
Add support to provide Statistical Counter interface to userspace.
This set of debug registers are part of the RAS DES feature present in
DesignWare PCIe controllers.
Co-developed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Hrishikesh Deleep <hrishikesh.d@samsung.com>
Link: https://lore.kernel.org/r/20250221131548.59616-6-shradha.t@samsung.com
[kwilczynski: commit log, tidy up code comments, update documentation,
squashed patch that checks if the event counter is supported from
https://lore.kernel.org/linux-pci/20250225171239.19574-3-manivannan.sadhasivam@linaro.org]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
Add support to provide Error Injection interface to userspace.
This set of debug registers are part of the RAS DES feature present in
DesignWare PCIe controllers.
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Tested-by: Hrishikesh Deleep <hrishikesh.d@samsung.com>
Link: https://lore.kernel.org/r/20250221131548.59616-5-shradha.t@samsung.com
[kwilczynski: commit log, tidy up code comments, update documentation,
change debugfs property name from "duplicate_dllp" to "duplicate_tlp"]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
Add support to provide Silicon Debug interface to userspace.
This set of debug registers are part of the RAS DES feature present in
DesignWare PCIe controllers.
Co-developed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Tested-by: Hrishikesh Deleep <hrishikesh.d@samsung.com>
Link: https://lore.kernel.org/r/20250221131548.59616-4-shradha.t@samsung.com
[kwilczynski: commit log, tidy up Kconfig and drop "default y", tidy up
code comments, squashed patch that fixes a NULL pointer dereference when
debugfs is already unavailable during clean-up from
https://lore.kernel.org/linux-pci/20250225171239.19574-2-manivannan.sadhasivam@linaro.org,
refactor dwc_pcie_debugfs_init() to not return errors, squashed patch that
changes how lack of the RAS DES capability is handled from
https://lore.kernel.org/linux-pci/20250304151814.6xu7cbpwpqrvcad5@thinkpad]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
Fix the following inconsistent indentation warning:
drivers/pci/controller/pcie-mediatek-gen3.c:922 mtk_pcie_parse_port() warn: inconsistent indenting
Found using Smatch. No functional changes intended.
Signed-off-by: Charles Han <hanchunchao@inspur.com>
Link: https://lore.kernel.org/r/20250305070022.4668-1-hanchunchao@inspur.com
[kwilczynski: commit log, refactor if-statement around num_lanes to
make it more readable, wrap overly long lines to fit 80 colums]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
The for_each_available_child_of_node_scoped() helper provides
a scope-based clean-up functionality to put the device_node
automatically, and as such, there is no need to call of_node_put()
directly.
Thus, use this helper to simplify the code.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240831040413.126417-2-zhangzekun11@huawei.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
Make the cast to the irq_hw_number_t type for the parameter passed to
irq_domain_set_info() function explicit.
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-9-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
The hardware has been updated with two changes to the MDIO packet
format.
The CMD field used to be 12 bits and now is only 1 bit. This change
is backwards compatible because the field's starting bit position is
unchanged, and the only commands we've used have values 0 and 1.
The PORT field's width has been changed from 4 bits to 5 bits. When
written, the new bit is not contiguous with the other four. However,
this change is backwards compatible because the driver never used
anything other than 0 for the port field's value.
Thus, update the existing code to handle new changes to the hardware
in a backwards-compatible manner.
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-8-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
The constants EXT_CFG_DATA and EXT_CFG_INDEX vary by SoC, where one of
the map_bus methods used these constants, and the other used a different
set of constants.
Thankfully, there was no problem because the SoCs that used the latter
map_bus method all had the same register constants.
Thus, remove redundant constants and adjust the code to use the correct
constants accordingly.
While at it, update the value of EXT_CFG_DATA to use the 4k-page based
configuration space access system, which is what the second map_bus
method was already using.
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20250214173944.47506-7-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
The platform supports enabling and disabling regulators only on
ports below the Root Complex.
Thus, we need to verify this both when adding and removing the bus,
otherwise regulators may be disabled prematurely when a bus further
down the topology is removed.
Fixes: 9e6be018b263 ("PCI: brcmstb: Enable child bus device regulators from DT")
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-6-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
If the regulator_bulk_get() returns an error and no regulators
are created, we need to set their number to zero.
If we don't do this and the PCIe link up fails, a call to the
regulator_bulk_free() will result in a kernel panic.
While at it, print the error value, as we cannot return an error
upwards as the kernel will WARN() on an error from add_bus().
Fixes: 9e6be018b263 ("PCI: brcmstb: Enable child bus device regulators from DT")
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20250214173944.47506-5-james.quinlan@broadcom.com
[kwilczynski: commit log, use comma in the message to match style with
other similar messages]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
When setting the LNKCAP and LNKCTL2 register fields, it was assumed
that the field started at the LSB of the register.
Although the masks do indeed start at the LSB, and this will probably
not change, it is prudent to use a method that makes no assumption
about the mask's placement in the register.
Thus, use the u{16,32}p_replace_bits() helpers since they are already
wildly used in this driver.
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-4-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
The driver has been mistakenly writing to a read-only (RO)
configuration space register (PCI_EXP_LNKCAP) to change the
PCIe link capability.
Although harmless in this case, the proper write destination
is an internal register that is reflected by PCI_EXP_LNKCAP.
Thus, fix the brcm_pcie_set_gen() function to correctly update
the link capability.
Fixes: c0452137034b ("PCI: brcmstb: Add Broadcom STB PCIe host controller driver")
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-3-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
When the user elects to limit the PCIe generation via the appropriate
devicetree property, apply the settings before the PCIe link up, not
after.
Fixes: c0452137034b ("PCI: brcmstb: Add Broadcom STB PCIe host controller driver")
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-2-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
