| Age | Commit message (Collapse) | Author |
|---|
|
Add pinctrl driver support for the Axis ARTPEC-6 SoC.
There are only some pins that actually have different
functions available, but all can control bias (pull-up/-down)
and drive strength.
Code originally written by Chris Paterson.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
SoC family such as DRA7 family of processors have, in addition
to the regular muxing of pins (as done by pinctrl-single), a separate
hardware module called IODelay which is also expected to be configured.
The "IODelay" module has it's own register space that is independent
of the control module and the padconf register area.
With recent changes to the pinctrl framework, we can now support
this hardware with a reasonably minimal driver by using #pinctrl-cells,
GENERIC_PINCTRL_GROUPS and GENERIC_PINMUX_FUNCTIONS.
It is advocated strongly in TI's official documentation considering
the existing design of the DRA7 family of processors during mux or
IODelay reconfiguration, there is a potential for a significant glitch
which may cause functional impairment to certain hardware. It is
hence recommended to do as little of muxing as absolutely necessary
without I/O isolation (which can only be done in initial stages of
bootloader).
NOTE: with the system wide I/O isolation scheme present in DRA7 SoC
family, it is not reasonable to do stop all I/O operations for every
such pad configuration scheme. So, we will let it glitch when used in
this mode.
Even with the above limitation, certain functionality such as MMC has
mandatory need for IODelay reconfiguration requirements, depending on
speed of transfer. In these cases, with careful examination of usecase
involved, the expected glitch can be controlled such that it does not
impact functionality.
In short, IODelay module support as a padconf driver being introduced
here is not expected to do SoC wide I/O Isolation and is meant for
a limited subset of IODelay configuration requirements that need to
be dynamic and whose glitchy behavior will not cause functionality
failure for that interface.
IMPORTANT NOTE: we take the approach of keeping LOCK_BITs cleared
to 0x0 at all times, even when configuring Manual IO Timing Modes.
This is done by eliminating the LOCK_BIT=1 setting from Step
of the Manual IO timing Mode configuration procedure. This option
leaves the CFG_* registers unprotected from unintended writes to the
CTRL_CORE_PAD_* registers while Manual IO Timing Modes are configured.
This approach is taken to allow for a generic driver to exist in kernel
world that has to be used carefully in required usecases.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[tony@atomide.com: updated to use generic pinctrl functions, added
binding documentation, updated comments]
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We can now drop the driver specific code for managing functions.
Signed-off-by: Tony Lindgren <tony@atomide.com>
[Replaces GENERIC_PINMUX with GENERIC_PINMUX_FUNCTIONS]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We can now drop the driver specific code for managing groups.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We can add generic helpers for function handling for cases where the pin
controller driver does not need to use static arrays.
Signed-off-by: Tony Lindgren <tony@atomide.com>
[Renamed the Kconfig item and moved things around]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Rename the symbol PINCTRL_GENERIC to PINCTRL_GENERIC_GROUPS since
it all pertains to groups. Replace everywhere.
ifdef out the radix tree and the struct when not using the
generic groups.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We can add generic helpers for pin group handling for cases where the pin
controller driver does not need to use static arrays.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds a new driver for pinconf on TI DA850/OMAP-L138/AM18XX. These
SoCs have a separate controller for controlling pullup/pulldown groups.
Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
To allow for future code simplification
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Drivers using pinconf_generic_params tables cannot be built with
CONFIG_OF disabled:
drivers/pinctrl/pinctrl-max77620.c:53:44: error: array type has incomplete element type ‘struct pinconf_generic_params’
drivers/pinctrl/pinctrl-max77620.c:55:3: error: field name not in record or union initializer
drivers/pinctrl/pinctrl-max77620.c:55:3: note: (near initialization for ‘max77620_cfg_params’)
drivers/pinctrl/pinctrl-max77620.c:56:3: error: field name not in record or union initializer
This adds a dependency for max77620 to disallow that configuration.
Alternatively, we could rework the pinctrl infrastructure to make the
configuration valid for compile-testing.
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Lee Jones <lee.jones@linaro.org>
Fixes: 453943dc8f45 ("mfd: Enable compile testing for max77620 and max77686")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Since the I2C sx150x GPIO expander driver uses platform_data to manage
the pins configurations, rewrite the driver as a pinctrl driver using
pinconf to get/set pin configurations from DT or debugfs.
The pinctrl driver is functionnally equivalent as the gpio-only driver
and can use DT for pinconf. The platform_data confirmation is dropped.
This patchset removed the gpio-only driver and selects the Pinctrl driver
config instead. This patchset also migrates the gpio dt-bindings to pinctrl
and add the pinctrl optional properties.
The driver was tested with a SX1509 device on a BeagleBone black with
interrupt support and on an X86_64 machine over an I2C to USB converter.
This is a fixed version that builds and runs on non-OF platforms and on
arm based OF. The GPIO version is removed and the bindings are also moved
to the pinctrl bindings.
Changes since v2
- rebased on v4.9-rc1
- removed MODULE_DEVICE_TABLE as in upstream bb411e771b0e
("gpio: sx150x: fix implicit assumption module.h is present")
Changes since v1
- Fix Kconfig descriptions on pinctrl and gpio
- Fix Kconfig dependency
- Remove oscio support for non-789 devices
- correct typo in dt bindings
- remove probe reset for non-789 devices
Changes since RFC
- Put #ifdef CONFIG_OF/CONFIG_OF_GPIO to remove OF code for non-of platforms
- No more rely on OF_GPIO config
- Moved and enhanced bindings to pinctrl bindings
- Removed gpio-sx150x.c
- Temporary select PINCTRL_SX150X when GPIO_SX150X
- Temporary mark GPIO_SX150X as deprecated
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
ested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Aspeed SoCs typically provide more than 200 pins for GPIO and other
functions. The signal enabled on a pin is determined on a priority
basis, where a given pin can provide a number of different signal types.
In addition to the priority levels, the Aspeed pin controllers describe
the signal active on a pin by compound logical expressions involving
multiple operators, registers and bits. Some difficulty arises as a
pin's function bit masks for each priority level are frequently not the
same (i.e. we cannot just flip a bit to change from a high to low
priority signal), or even in the same register(s). Some configuration
bits affect multiple pins, while in other cases the signals for a bus
must each be enabled individually.
Together, these features give rise to some complexity in the
implementation. A more complete description of the complexities is
provided in the associated header file.
The patch doesn't implement pinctrl/pinmux/pinconf for any particular
Aspeed SoC, rather it adds the framework for defining pinmux
configurations.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Kconfig currently controlling compilation of this code is:
config PINCTRL_AS3722
bool "Pinctrl and GPIO driver for ams AS3722 PMIC"
...meaning that it currently is not being built as a module by anyone.
During an audit for non-modular drivers using modular infrastructure
this driver showed up.
But rather than demodularize it, Laxman indicated that it would be
prefereable to instead convert the driver option to tristate.
This does that, and confirms that it will compile and modpost as
such. However, since I do not have the hardware to confirm that
no new runtime issues exist when modular, that remains untested.
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Kconfig currently controlling compilation of this code is:
config PINCTRL_PALMAS
bool "Pinctrl driver for the PALMAS Series MFD devices"
...meaning that it currently is not being built as a module by anyone.
During an audit for non-modular drivers using modular infrastructure
this driver showed up.
But rather than demodularize it, Laxman indicated that it would be
prefereable to instead convert the driver option to tristate.
This does that, and confirms that it will compile and modpost as
such. However, since I do not have the hardware to confirm that
no new runtime issues exist when modular, that remains untested.
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The recently added max77620 driver fails to build when CONFIG_PINMUX
is not set:
pinctrl/pinctrl-max77620.c:272:21: error: variable 'max77620_pinmux_ops' has initializer but incomplete type
static const struct pinmux_ops max77620_pinmux_ops = {
^~~~~~~~~~
pinctrl/pinctrl-max77620.c:273:2: error: unknown field 'get_functions_count' specified in initializer
This adds the Kconfig 'select' statement that was clearly meant
to be there and is used in all other pinmux drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
MAXIM Semiconductor's PMIC, MAX77620/MAX20024 has 8 GPIO pins
which also act as the special function in alternate mode. Also
there is configuration like push-pull, open drain, FPS timing
etc for these pins.
Add pin control driver to configure these parameters through
pin control APIs.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add pinctrl and gpio control support to Oxford Semiconductor OXNAS SoC Family.
This version supports the ARM926EJ-S based OX810SE SoC with 34 IO pins.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The pinctrl-amd driver builds just fine as a module so give
users this option.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add a driver for the pin controller present on the Microchip PIC32
including the specific variant PIC32MZDA. This driver provides pinmux
and pinconfig operations as well as GPIO and IRQ chips for the GPIO
banks.
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Tegra has several pinctrl drivers. Now it is reasonable enough to
move them into drivers/pinctrl/tegra/.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch adds pinctrl and GPIO support to STMicroelectronic's STM32
family of MCUs.
While it only supports STM32F429 for now, it has been designed to enable
support of other MCUs of the family (e.g. STM32F746).
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Linux 4.4-rc5
|
|
As the pxa architecture, at least for pxa27x, supports pin control,
activate it in the pinctrl tree.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The whole menu is guarded by
menu "Pin controllers"
depends on PINCTRL
...
endmenu
The if conditional outside of it is redundant.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add a pinctrl/gpio driver for Atmel PIO4 controller available on SAMA5D2
chip family.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds pinctrl and gpio driver to the CX92755 SoC "General
Purpose Pin Mapping" hardware block. The CX92755 is one SoC
from the Conexant Digicolor series. Pin mapping hardware supports
configuring pins as either GPIO, or up to 3 other "client select"
functions. This driver adds support for pin muxing using the
generic device tree binding, and a basic gpiolib driver for
the GPIO functionality.
This driver does not currently support GPIO interrupts, and
pad configuration.
v2:
* Address review comments for Linus Walleij:
- Add a pointer to pinctrl_desc in struct dc_pinmap
- Drop the now redundant pinctrl_pin_desc field
- Adapt dc_get_group_{name,pins} to these changes, and
add a comment explaining the 1-to-1 pin-groups relation
* Staticise dc_pmxops
* Protect the GP_CLIENTSEL clct parameter with parenthesis
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The core support for the pinctrl drivers for all the UniPhier SoCs.
Changes in v2:
- drop vogus THIS_MODULE because this file is always built-in
- drop vogus "include <linux/module.h> because this file is
always built-in
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Pinctrl module (ioc) controls the Pad's function select
(each pad can have 8 functions), Pad's Drive Strength, Pad's
Pull Select and Pad's Input Disable status.
The ioc has two modules, ioc_top & ioc_rtc. Both of these two
modules have function select/clear, Pull select and Drive
Strength registers. But only ioc_rtc has input-disable
registers. The Pads on ioc_top have to access ioc_rtc to set
their input-disable status and intpu-disable-value.
So have to use one ioc driver instance to drive these two
ioc modules at the same time, and each ioc module will be
treat as one bank on the "IOC Device".
The GPIO Controller controls the GPIO status if the Pad has
been config as GPIO by Pinctrl already. Includes the GPIO
Input/output, Interrupt type, Interrupt Status, and Set/Get
Values.
The GPIO pull up/down are controlled by Pinctrl.
There are 7 GPIO Groups and splited into 3 MACROs in atlas7.
The GPIO Groups in one MACRO share one GPIO controllers, each
GPIO Group are treated as one GPIO bank.
For example:
In VDIFM macro, there is one GPIO Controller, it has 3 banks
to control 3 gpio groups. Its gpio name space is from 0 to 95.
The Device Tree can be written as following:
gpio-ranges = <&pinctrl 0 0 0>,
<&pinctrl 32 0 0>,
<&pinctrl 64 0 0>;
gpio-ranges-group-names = "gnss_gpio_grp",
"lcd_vip_gpio_grp",
"sdio_i2s_gpio_grp";
bank#0 is from 0~31, the pins are from pinctrl's "gnss_gpio_grp".
bank#2 is from 32~63, the pins are from pinctrl's "lcd_vip_gpio_grp".
bank#3 is from 64~95, the pins are from pinctrl's "sdio_i2s_gpio_grp".
Signed-off-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add a driver for the pin controller present on the IMG Pistachio SoC.
This driver provides pinmux and pinconfig operations as well as GPIO
and IRQ chips for the GPIO banks.
Changes from v4:
- Switched to using gpiochip_add_pin_range().
- Fixed up Kconfig entry.
Changes from v3:
- Addressed review comments from Ezequiel.
Changes from v2:
- Removed module stuff which would be compiled out.
Changes from v1:
- Addressed review comments from Linus.
- Changed compatible string to "img,pistachio-system-pinctrl".
- Look for GPIO sub-nodes by name.
- A couple of bug fixes.
Signed-off-by: Damien Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Pinctrl driver for the System Control Unit (SCU) found on NXP
LPC18xx/43xx devices.
Driver uses the generic pinctrl DT bindings for multiplexing
and property settings.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There was some mess in the dependencies in the pinctrl
Kconfig for compile tests under allmodconfig. Mea Culpa.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
KERNCZ GPIO is a new IP from AMD. it can be implemented in both x86 and ARM.
Current driver patch only support GPIO in x86.
Signed-off-by: Ken Xue <Ken.Xue@amd.com>
[Moved back to <linux/gpio.h> header]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The mediatek SoCs have GPIO controller that handle both the muxing and GPIOs.
The GPIO controller have pinmux, pull enable, pull select, direction and output high/low control.
This driver include common driver and mt8135 part.
The common driver include the pinctrl driver and GPIO driver.
The mt8135 part contain its special device data.
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Consolidate Broadcom pinctrl drivers into drivers/pinctrl/bcm/*
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Tegra210's pinmux supports a different set of pins/options than earlier
SoCs, so requires its own driver (well, table of pin-specific data).
Cc: devicetree@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This is a driver for the pinmux and GPIO controller available in
Amlogic Meson SoCs. It currently supports only Meson8, however the
common code should be generic enough to work also for other SoCs after
having defined the proper set of functions and groups.
GPIO interrupts are not supported at the moment due to lack of
documentation.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
marco chip has been dropped, clear its support.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds a pin-control driver for Zynq.
Changes since v2:
- driver-specific DT properties are passed to the core in two arrays,
one for the actual DT parsing one for the debugfs representation.
Issue a compiler warning when the number of entries is not the same
for both arrays.
Changes since v1:
- fix EMIO_SD1_CD pin name
- add USB to pinmux options
changes since RFCv2:
- let Zynq select PINCTRL_ZYNQ. Boot hangs when pinctrl information is
present in DT but no driver available.
- add #defines to get rid of magical constants
- add commas at end of initializers
- separate changes in mach-zynq in separate patch
- add driver specific io-standard DT property
- refactored pinconf set function to not require arguments for
argument-less properties
- squash other patches in
- support for IO-standard property
- support for low-power mode property
- migration to pinconf_generic_dt_node_to_map_all()
- use newly created infrastructure to add pass driver-specific DT
params to pinconf-generic
changes since RFC:
- use syscon/regmap to access registers in SLCR space
- rebase to 3.18: rename enable -> set_mux
- add kernel-doc
- support pinconf
- supported attributes
- pin-bias: pull up, tristate, disable
- slew-rate: 0 == slow, 1 == fast; generic pinconf does not display
argument
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We are going to have more pinctrl drivers for Intel hardware so separate
all our pin controller drivers to own directory.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the bulk of GPIO changes for the v3.18 development cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This was done
to avoid having a custom <asm/gpio.h> header for the x86
architecture - GPIO is custom and complicated enough as it is
already! We want to move to a radix to store the descriptors going
forward, and finally get rid of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated by
Abdoulaye Berthe. It is not accepted by the system that the
removal of a GPIO chip fails during eg reboot or shutdown, and
therefore the return value has now painfully been refactored away.
For special cases like GPIO expanders on a hot-pluggable bus like
USB, we may later add some gpiochip_try_remove() call, but for the
cases we have now, return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI GPIO
library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle also
threaded, nested interrupts and set up the parent IRQ correctly.
Switch STMPE and TC3589x drivers to use this registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so that also
GPIO expanders that block but are still not using threaded IRQ
handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the "DSP GPIO"
found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated from and
MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08, DWAPB, OMAP,
Xilinx and Crystalcove drivers.
- Various minor fixes"
* tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (52 commits)
gpio: pch: Build context save/restore only for PM
pinctrl: abx500: get rid of unused variable
gpio: ks8695: fix 'else should follow close brace '}''
gpio: stmpe: add verbose debug code
gpio: stmpe: fix up interrupt enable logic
gpio: staticize xway_stp_init()
gpio: handle also nested irqchips in the chained handler set-up
gpio: set parent irq on chained handlers
gpiolib: irqchip: use irq_find_mapping while removing irqchip
gpio: crystalcove: support virtual GPIO
pinctrl: bcm281xx: make Kconfig dependency more strict
gpio: kona: enable only on BCM_MOBILE or for compile testing
gpio, bcm-kona, LLVMLinux: Remove use of __initconst
gpio: Fix ngpio in gpio-xilinx driver
gpio: dwapb: fix pointer to integer cast
gpio: xgene: Remove unneeded #ifdef CONFIG_OF guard
gpio: xgene: Remove unneeded forward declation for struct xgene_gpio
gpio: xgene: Fix missing spin_lock_init()
gpio: ks8695: fix switch case indentation
gpiolib: add irq_not_threaded flag to gpio_chip
...
|
|
This driver is only useful on BCM281xx, so let the driver depend on
ARCH_BCM_MOBILE but allow compile coverage testing.
The main benefit is that the driver isn't available to be selected for
machines that don't have the matching hardware.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Sherman Yin <syin@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This moves all the Freescale-related drivers (i.MX and MXS) to
its own subdirectory to clear the view.
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Anson Huang <b20788@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Denis Carikli <denis@eukrea.com>
Cc: Markus Pargmann <mpa@pengutronix.de>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch adds pincontrol driver for Freescale i.MX21 SOCs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device-tree changes from Olof Johansson:
"Unlike the board branch, this keeps having large sets of changes for
every release, but that's quite expected and is so far working well.
Most of this is plumbing for various device bindings and new
platforms, but there's also a bit of cleanup and code removal for
things that are moved from platform code to DT contents (some OMAP
clock code in particular).
There's also a pinctrl driver for tegra here (appropriately acked),
that's introduced this way to make it more bisectable.
I'm happy to say that there were no conflicts at all with this branch
this release, which means that changes are flowing through our tree as
expected instead of merged through driver maintainers (or at least not
done with conflicts).
There are several new boards added, and a couple of SoCs. In no
particular order:
- Rockchip RK3288 SoC support, including DTS for a dev board that
they have seeded with some community developers.
- Better support for Hardkernel Exynos4-based ODROID boards.
- CCF conversions (and dtsi contents) for several Renesas platforms.
- Gumstix Pepper (TI AM335x) board support
- TI eval board support for AM437x
- Allwinner A23 SoC, very similar to existing ones which mostly has
resulted in DT changes for support. Also includes support for an
Ippo tablet with the chipset.
- Allwinner A31 Hummingbird board support, not to be confused with
the SolidRun i.MX-based Hummingboard.
- Tegra30 Apalis board support"
* tag 'dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (334 commits)
ARM: dts: Enable USB host0 (EHCI) on rk3288-evb
ARM: dts: add rk3288 ehci usb devices
ARM: dts: Turn on USB host vbus on rk3288-evb
ARM: tegra: apalis t30: fix device tree compatible node
ARM: tegra: paz00: Fix some indentation inconsistencies
ARM: zynq: DT: Clarify Xilinx Zynq platform
ARM: dts: rockchip: add watchdog node
ARM: dts: rockchip: remove pinctrl setting from radxarock uart2
ARM: dts: Add missing pinctrl for uart0/1 for exynos3250
ARM: dts: Remove duplicate 'interrput-parent' property for exynos3250
ARM: dts: Add TMU dt node to monitor the temperature for exynos3250
ARM: dts: Specify MAX77686 pmic interrupt for exynos5250-smdk5250
ARM: dts: cypress,cyapa trackpad is exynos5250-Snow only
ARM: dts: max77686 is exynos5250-snow only
ARM: zynq: DT: Remove DMA from board DTs
ARM: zynq: DT: Add CAN node
ARM: EXYNOS: Add exynos5260 PMU compatible string to DT match table
ARM: dts: Add PMU DT node for exynos5260 SoC
ARM: EXYNOS: Add support for Exynos5410 PMU
ARM: dts: Add PMU to exynos5410
...
|
|
Instead of open-coding irqchip handling in the driver we can take advantage
of the new irqchip helpers provided by the gpiolib core.
While doing this we also make sure that we call gpiochip_irqchip_add()
after the gpiochip itself is registered as required.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We have a bunch of Nomadik family pin control drivers, so let's
move them into their own subdirectory.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The XUSB pad controller found on NVIDIA Tegra SoCs provides several pads
that lanes can be assigned to in order to support a variety of interface
options: USB 2.0, USB 3.0, PCIe and SATA.
In addition to the pin controller used to assign lanes to pads two PHYs
are exposed to allow the bricks for PCIe and SATA to be powered up and
down by PCIe and SATA drivers.
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Group all pin control drivers of Samsung platform together in
a sub-directory for easy maintenance.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We have four Qualcomm-related pin control drivers, and now there
are drivers coming in for the PMICs on these systems, so let's
create a qcom subdirectory to hold all the Qualcomm stuff.
Acked-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
