| Age | Commit message (Collapse) | Author |
|---|
|
On AST2500, the hardware strap register(SCU70) only accepts write ‘1’,
to clear it to ‘0’, must set bits(write ‘1’) to SCU7C
Signed-off-by: Yong Li <sdliyong@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Tested-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Several pinconf parameters have a fairly straight-forward mapping onto
the Aspeed pin controller. These include management of pull-down bias,
drive-strength, and some debounce configuration.
Pin biasing largely is managed on a per-GPIO-bank basis, aside from the
ADC and RMII/RGMII pins. As the bias configuration for each pin in a
bank maps onto a single per-bank bit, configuration tables will be
introduced to describe the ranges of pins and the supported pinconf
parameter. The use of tables also helps with the sparse support of
pinconf properties, and the fact that not all GPIO banks support
biasing or drive-strength configuration.
Further, as the pin controller uses a consistent approach for bias and
drive strength configuration at the register level, a second table is
defined for looking up the the bit-state required to enable or query the
provided configuration.
Testing for pinctrl-aspeed-g4 was performed on an OpenPOWER Palmetto
system, and pinctrl-aspeed-g5 on an AST2500EVB as well as under QEMU.
The test method was to set the appropriate bits via devmem and verify
the result through the controller's pinconf-pins debugfs file. This
simultaneously validates the get() path and half of the set() path. The
remainder of the set() path was validated by configuring a handful of
pins via the devicetree with the supported pinconf properties and
verifying the appropriate registers were touched.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The patch introducing the g5 pinctrl driver implemented a smattering of
pins to flesh out the implementation of the core and provide bare-bones
support for some OpenPOWER platforms and the AST2500 evaluation board.
Now, update the bindings document to reflect the complete functionality
and implement the necessary pin configuration tables in the driver.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The System Control Unit IP block in the Aspeed SoCs is typically where
the pinmux configuration is found, but not always. A number of pins
depend on state in one of LPC Host Control (LHC) or SoC Display
Controller (GFX) IP blocks, so the Aspeed pinmux drivers should have the
means to adjust these as necessary.
We use syscon to cast a regmap over the GFX and LPC blocks, which is
used as an arbitration layer between the relevant driver and the pinctrl
subsystem. The regmaps are then exposed to the SoC-specific pinctrl
drivers by phandles in the devicetree, and are selected during a mux
request by querying a new 'ip' member in struct aspeed_sig_desc.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Aspeed SoCs typically provide more than 200 pins for GPIO and other
functions. The signal enabled on a pin is determined on a priority
basis, where a given pin can provide a number of different signal types.
In addition to the priority levels, the Aspeed pin controllers describe
the signal active on a pin by compound logical expressions involving
multiple operators, registers and bits. Some difficulty arises as a
pin's function bit masks for each priority level are frequently not the
same (i.e. we cannot just flip a bit to change from a high to low
priority signal), or even in the same register(s). Some configuration
bits affect multiple pins, while in other cases the signals for a bus
must each be enabled individually.
Together, these features give rise to some complexity in the
implementation. A more complete description of the complexities is
provided in the associated header file.
The patch doesn't implement pinctrl/pinmux/pinconf for any particular
Aspeed SoC, rather it adds the framework for defining pinmux
configurations.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
