| Age | Commit message (Collapse) | Author |
|---|
|
GPIOD_OUT_HIGH)
The pins on the Bay Trail SoC have separate input-buffer and output-buffer
enable bits and a read of the level bit of the value register will always
return the value from the input-buffer.
The BIOS of a device may configure a pin in output-only mode, only enabling
the output buffer, and write 1 to the level bit to drive the pin high.
This 1 written to the level bit will be stored inside the data-latch of the
output buffer.
But a subsequent read of the value register will return 0 for the level bit
because the input-buffer is disabled. This causes a read-modify-write as
done by byt_gpio_set_direction() to write 0 to the level bit, driving the
pin low!
Before this commit byt_gpio_direction_output() relied on
pinctrl_gpio_direction_output() to set the direction, followed by a call
to byt_gpio_set() to apply the selected value. This causes the pin to
go low between the pinctrl_gpio_direction_output() and byt_gpio_set()
calls.
Change byt_gpio_direction_output() to directly make the register
modifications itself instead. Replacing the 2 subsequent writes to the
value register with a single write.
Note that the pinctrl code does not keep track internally of the direction,
so not going through pinctrl_gpio_direction_output() is not an issue.
This issue was noticed on a Trekstor SurfTab Twin 10.1. When the panel is
already on at boot (no external monitor connected), then the i915 driver
does a gpiod_get(..., GPIOD_OUT_HIGH) for the panel-enable GPIO. The
temporarily going low of that GPIO was causing the panel to reset itself
after which it would not show an image until it was turned off and back on
again (until a full modeset was done on it). This commit fixes this.
This commit also updates the byt_gpio_direction_input() to use direct
register accesses instead of going through pinctrl_gpio_direction_input(),
to keep it consistent with byt_gpio_direction_output().
Note for backporting, this commit depends on:
commit e2b74419e5cc ("pinctrl: baytrail: Replace WARN with dev_info_once
when setting direct-irq pin to output")
Cc: stable@vger.kernel.org
Fixes: 86e3ef812fe3 ("pinctrl: baytrail: Update gpio chip operations")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Since we dependent on ACPI, there is no need to use ACPI_PTR()
which is a no-op in this case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Since we dependent on ACPI, there is no need to use ACPI_PTR()
which is a no-op in this case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Introduce couple of helpers to enable or disable input. i.e.
lp_gpio_enable_input() and lp_gpio_disable_input().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Make use of for_each_requested_gpio() instead of home grown analogue.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Make use of for_each_requested_gpio_in_range() instead of home grown analogue.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Protect IO in intel_gpio_get_direction(), intel_gpio_community_irq_handler(),
intel_config_get_debounce() and intel_config_get_pull() by lock. Even for
simple readl() we better serialize IO to avoid potential problems.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Split intel_config_get() to three functions, i.e. intel_config_get() and
two helpers intel_config_get_pull() and intel_config_get_debounce() to be
symmetrical with intel_config_set*().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Drop the only label in the code, i.e. in intel_config_set_debounce(),
for consistency with the rest. In entire driver we use multipoint
return.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In a code like
if (...) {
...
goto label;
} else {
...
}
the 'else' keyword is redundant. Get rid of it for better readability.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Instead of using bitwise operations against returned values,
which is a bit fragile, convert IRQ handler to count amount of
GPIO groups, where at least one interrupt happened, and convert
it to returned value by IRQ_RETVAL() macro.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In some cases lock covers unneeded calls and operations.
Reduce scope of the lock in such cases.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
It's possible scenario that pin has been in different mode, while
the respective GPIO register has a leftover output buffer enabled.
In such case when we request GPIO it will switch to GPIO mode, and
thus to output with unknown value, followed by switching to input
mode. This can produce a glitch on the pin.
Disable input and output buffer when switching to GPIO to avoid
potential glitches.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We have some data structures duplicated across the drivers.
Let's deduplicate them by using struct intel_pinctrl_soc_data,
struct intel_community and struct intel_pinctrl_context that
are being provided by pinctrl-intel.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Individual drivers may install ACPI OpRegion handlers based on
address space ID which differs from community to community.
Add special field in the struct intel_community for that purpose.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Some of the pin control devices may not be capable to generate IRQ
per each pin in the community. Allow individual drivers to define
total amount of IRQs per community.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
chv_writel() is now solely used for cases where we write data
to the PAD registers. In order to simplify callers, calculate
register address inside chv_writel().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Pin control device and effectively the single community in it has
a set of common registers. It's good to have a helpers to IO on them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
There are plenty of places where we call
readl(chv_padreg(pctrl, offset, ...));
Replace them with newly introduced chv_readl() helper
chv_readl(pctrl, offset, ...);
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
It's common across the drivers to use the (pin_base, npins) pair to describe
community characteristics. Thus, move them in the struct intel_community
to be closer to each other.
While at it, add a blank line to cut driver usable fields from what core
reserves for itself.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
It appears that most of the drivers, that are using struct intel_community,
utilize gpps rather than gpp_size. Update comment accordingly.
While here, correct the description of gpp_size, i.e. remove double space
and drop redundant 'etc.' part.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
According to Braswell NDA Specification Update (#557593),
concurrent read accesses may result in returning 0xffffffff and write
instructions may be dropped. We have an established format for the
commit references, i.e.
cdca06e4e859 ("pinctrl: baytrail: Add missing spinlock usage in
byt_gpio_irq_handler")
Fixes: 0bd50d719b00 ("pinctrl: cherryview: prevent concurrent access to GPIO controllers")
Signed-off-by: Grace Kao <grace.kao@intel.com>
Reported-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
There is no need to repeat functionality of platform_get_irq_optional()
in the driver. Replace it with explicit call to the helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There is no need to repeat functionality of platform_get_irq_optional()
in the driver. Replace it with explicit call to the helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
This driver adds pinctrl/GPIO support for Intel Jasper Lake SoC. The
GPIO controller is based on the next generation GPIO hardware but still
compatible with the one supported by the Intel core pinctrl/GPIO driver.
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In some cases not the first group would like to have GPIO base to be 0.
It's not possible right now due to 0 has special meaning already. Thus,
introduce a new flag to allow drivers to force GPIO base to be 0 on
a certain group. It's assumed that it can be only one group per device
with such flag enabled.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Since we have a generic flag for special GPIO base treatment,
use it in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Since we have a generic flag for special GPIO base treatment,
use it in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Since we have a generic flag for special GPIO base treatment,
use it in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Few drivers are using the same flag to tell Intel pin control core
how to interpret GPIO base.
Provide a generic flags so all drivers can use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Use GENMASK() macro for all definitions where it's appropriate.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We have some data structures duplicated across the drivers.
Let's deduplicate them by using ones that being provided by
pinctrl-intel.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
It appears that pin configuration for GPIO chip hasn't been enabled yet
due to absence of ->set_config() callback.
Enable it here for Intel Baytrail.
Fixes: c501d0b149de ("pinctrl: baytrail: Add pin control operations")
Depends-on: 2956b5d94a76 ("pinctrl / gpio: Introduce .set_config() callback for GPIO chips")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
It appears that SPT-H variant has different offset for PAD locking registers.
Fix it here.
Fixes: 551fa5801ef1 ("pinctrl: intel: sunrisepoint: Add Intel Sunrisepoint-H support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Turns out that Tiger Lake GPIO will be enumerated using _HID method where
there is only a single ACPI device and multiple BARs so rework the driver
to support that scheme instead.
Fixes: c9ccf71fc807 ("pinctrl: intel: Add Intel Tiger Lake pin controller support")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Intel Coffee Lake-S PCH has the same GPIO hardware than Sunrisepoint-H
PCH but the ACPI ID is different. Add this new ACPI ID to the list of
supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward conversion.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
When IRQ chip is instantiated via GPIO library flow, the few functions,
in particular the ACPI event registration mechanism, on some of ACPI based
platforms expect that the pin ranges are initialized to that point.
Add GPIO <-> pin mapping ranges via callback in the GPIO library flow.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
pin to output
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.
On Cherry Trail device the interrupt pin is listed as a GpioInt ACPI
resource so we can do this without problems as long as we release the
IRQ before changing the pin to output mode.
On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
in combination with listing the pin as a normal GpioIo resource. This
works fine, but this triggers the WARN in byt_gpio_set_direction-s output
path because direct-irq support is enabled on the pin.
This commit replaces the WARN call with a dev_info_once call, fixing a
bunch of WARN splats in dmesg on each suspend/resume cycle.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.
On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
in combination with listing the pin as a normal GpioIo resource.
This works fine, until the goodix driver gets rmmod-ed and then insmod-ed
again. In this case byt_gpio_disable_free() calls
byt_gpio_clear_triggering() which clears the IRQ flags and after that the
(direct) IRQ no longer triggers.
This commit fixes this by adding a check for the BYT_DIRECT_IRQ_EN flag
to byt_gpio_clear_triggering().
Note that byt_gpio_clear_triggering() only gets called from
byt_gpio_disable_free() for direct-irq enabled pins, as these are excluded
from the irq_valid mask by byt_init_irq_valid_mask().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Commit 179e5a6114cc ("pinctrl: intel: Remove default Interrupt Status
offset") removes default interrupt status offset of GPIO controllers,
with previous commits explicitly providing the previously default
offsets. However, the is_offset value in SPTH_COMMUNITY is missing,
preventing related irq from being properly detected and handled.
Fixes: f702e0b93cdb ("pinctrl: sunrisepoint: Provide Interrupt Status register offset")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205745
Cc: stable@vger.kernel.org
Signed-off-by: Boyan Ding <boyan.j.ding@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Reflect in the driver that it is now a pin control one.
While here, update copyright years and authors.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
When all preparations are done, we may switch to pin control API.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
When IRQ chip is instantiated via GPIO library flow, the few functions,
in particular the ACPI event registration mechanism, on some of ACPI based
platforms expect that the pin ranges are initialized to that point.
Add GPIO <-> pin mapping ranges via callback in the GPIO library flow.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
The introduced callback ->pin_dbg_show() is useful for debugging.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Add implementation for:
- pin control, group information retrieval: count, name and pins
- pin muxing:
- function information (count, name and groups)
- mux setting
- GPIO control (enable, disable, set direction)
- pin configuration:
- pull disable, up and down
- any other option is treated as not supported.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We may use now available struct intel_pinctrl in the driver.
No functional change implied.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In order to implement pin control for Intel Lynxpoint, we need
data structures in which to store and pass along pin, community
and SoC data information.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Allows querying GPIO direction from the pad config register.
If the pad is not in GPIO mode, return an error.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Instead of playing tricks with registers in the interrupt handler,
utilize the IRQ chip core for ACKing interrupts properly.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
