| Age | Commit message (Collapse) | Author |
|---|
|
There is no need to acquire the spinlock when reading from a pin
controller register:
1. Reading a single MMIO register is an atomic operation,
2. While sh_pfc_phys_to_virt() inside sh_pfc_read() has to traverse
all mapped windows to find the appropriate virtual address, this
does not need any locking, as the window mappings are never
changed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/2008ca99f0079fd5d4e640b7ef78710c98cc9f77.1637143108.git.geert+renesas@glider.be
|
|
Implement support for pull-up (most pins, excl. DU_DOTCLKIN0) and
pull-down (most pins, excl. JTAG) handling for the R-Car D3 SoC, using
some parts from the common R-Car bias handling, which requires making
rcar_pin_to_bias_reg() public.
R-Car D3 needs special handling for the NFRE# (GP_3_0) and NFWE#
(GP_3_1) pins. Unlike all other pins, they are controlled by different
bits in the LSI pin pull-up/down control register (PUD2) than in the LSI
pin pull-enable register (PUEN2).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/04aad2b0bf82a32fb08e5e21e4ac1fb03452724f.1625064076.git.geert+renesas@glider.be
|
|
When disabling pin bias, there is no need to touch the LSI pin
pull-up/down control register (PUDn), which selects between pull-up and
pull-down. Just disabling the pull-up/down function through the LSI pin
pull-enable register (PUENn) is sufficient.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/071ec644de2555da593a4531ef5d3e4d79cf997d.1625064076.git.geert+renesas@glider.be
|
|
Currently, the common R-Car bias handling supports pin controllers with
either:
1. Separate pin Pull-Enable (PUEN) and pin Pull-Up/Down control (PUD)
registers, for controlling both pin pull-up and pin pull-down,
2. A single pin Pull-Up control register (PUPR), for controlling pin
pull-up.
Add support for a variant of #2, where some bits in the single pin
Pull-Up control register (PUPR) control pin pull-down instead of pin
pull-up. This is the case for the "ASEBRK#/ACK" pin on R-Car M2-W,
M2-N, and E2, and the "ACK" pin on RZ/G1M, RZ/G1N, RZ/G1E, and RZ/G1C.
To describe such a register, SoC-specific drivers need to provide two
instances of pinmux_bias_reg: a first one with the puen field filled in,
listing pins with pull-up functionality, and a second one with the pud
field filled in, listing pins with pull-down functionality.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210303132619.3938128-6-geert+renesas@glider.be
|
|
The pin control sub-drivers for SH/R-Mobile SoCs contain almost
identical bias handling. The only SoC-specific part is the mapping from
pin numbers to PORTnCR registers.
Reduce code duplication by factoring out the bias handling to the common
pinctrl.c code. Use a callback to handle the pin/register mapping.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210303132619.3938128-4-geert+renesas@glider.be
|
|
Now all R-Car pin control drivers have been converted to the common
R-Car bias handling, sh_pfc_pin_to_bias_reg() is only called from a
single place. Move it from core.c to pinctrl.c, make it static, and
rename it to rcar_pin_to_bias_reg(), as it is specific to R-Car SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210303132619.3938128-2-geert+renesas@glider.be
|
|
This patch adds config macros describing the voltage levels available on
a pin. The current default (3.3V/1.8V) maps to zero to avoid having to
change existing PFC implementations.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210112165912.30876-3-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
On SuperH and ARM SH/R-Mobile SoCs, the pin control driver handles
GPIOs, too. To reduce code size when compiling a kernel supporting only
modern SoCs, most, but not all, of the GPIO functionality is protected
by checks for CONFIG_PINCTRL_SH_FUNC_GPIO.
Factor out the remaining parts when not needed:
1. sh_pfc_soc_info.{in,out}put describe GPIO pins that have input
resp. output capabilities (SuperH and SH/R-Mobile).
2. sh_pfc_soc_info.gpio_irq{,_size} describe the mapping from GPIO
pins to interrupt numbers (SH/R-Mobile).
3. sh_pfc_gpio_set_direction() configures GPIO direction, called from
the GPIO driver through pinctrl_gpio_direction_{in,out}put()
(SH/R-Mobile). Unfortunately this function cannot just be moved to
drivers/pinctrl/renesas/gpio.c, as it relies on knowledge of
sh_pfc_pinctrl, which is internal to
drivers/pinctrl/renesas/pinctrl.c.
While code size reduction is minimal, this does help in documenting
depencies.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201028151637.1734130-9-geert+renesas@glider.be
|
|
Currently, the rcar_pinmux_[gs]et_bias() helpers handle only SoCs that
have separate LSI Pin Pull-Enable (PUEN) and Pull-Up/Down Control (PUD)
registers, like R-Car Gen3 and RZ/G2. Update the function to handle
SoCs that have only LSI Pin Pull-Up Control Register (PUPR), like R-Car
Gen1/Gen2 and RZ/G1.
Reduce code duplication by converting the R-Car M1A pin control driver
to use the common handler.
Note that this changes behavior in case the (invalid!) option
"bias-pull-down" is used in an R-Car M1A DTS: before, it was ignored
silently; after this change, it is considered the same as
"bias-pull-up".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201028151637.1734130-8-geert+renesas@glider.be
|
|
All pin control drivers for R-Car Gen3 SoCs contain identical bias
handling. Reduce code duplication by moving it to the common pinctrl.c
code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201028151637.1734130-6-geert+renesas@glider.be
|
|
Shrink sh_pfc_pin_config from 8 to 2 bytes:
- The mux_set flag can be removed, as a non-zero mark value means the
same (zero = PINMUX_RESERVED is an invalid mark value),
- The gpio_enabled flag needs only a single bit,
- Mark values are small integers, and can easily fit in a 15-bit
bitfield.
This saves 6 bytes per pin when allocating the sh_pfc_pinctrl.configs
array, i.e. it reduces run-time memory consumption by ca. 1.5 KiB.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201028151637.1734130-5-geert+renesas@glider.be
|
|
Fix a few singular vs. plural grammar issues in comments.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201028151637.1734130-3-geert+renesas@glider.be
|
|
Commit b13431ed6eab808a ("pinctrl: sh-pfc: Remove incomplete flag
"cfg->type"") removed the last statement in between the goto and the
label. Hence remove both.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201028151637.1734130-2-geert+renesas@glider.be
|
|
The drivers/pinctrl/sh-pfc subdirectory was originally created to group
pin control drivers for various Renesas SuperH and SH-Mobile platforms.
However, the name "sh-pfc" no longer reflects its contents, as the
directory now contains pin control drivers for Renesas SuperH, ARM32,
and ARM64 SoCs.
Hence rename the subdirectory from drivers/pinctrl/sh-pfc to
drivers/pinctrl/renesas, and the related Kconfig symbol from
PINCTRL_SH_PFC to PINCTRL_RENESAS.
Rename the git branch in MAINTAINERS, too, for consistency.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200909131534.12897-3-geert+renesas@glider.be
|
