summaryrefslogtreecommitdiff
path: root/drivers/scsi/NCR5380.c
AgeCommit message (Collapse)Author
2018-11-05scsi: NCR5380: Return false instead of NULLFinn Thain
I overlooked this statement when I recently converted the function result type from struct scsi_cmnd * to bool. No change to object code. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-09-28scsi: NCR5380: Check for bus resetFinn Thain
The SR_RST bit isn't latched. Hence, detecting a bus reset isn't reliable. When it is detected, the right thing to do is to drop all connected and disconnected commands. The code for that is already present so refactor it and call it when SR_RST is set. Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-09-28scsi: NCR5380: Handle BUS FREE during reselectionFinn Thain
The X3T9.2 specification (draft) says, under "6.1.4.2 RESELECTION time-out procedure", that a target may assert RST or go to BUS FREE phase if the initiator does not respond within 200 us. Something like this has been observed with AztecMonster II target. When it happens, all we can do is wait for the target to try again. Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-09-28scsi: NCR5380: Don't call dsprintk() following reselection interruptFinn Thain
The X3T9.2 specification (draft) says, under "6.1.4.1 RESELECTION", ... The reselected initiator shall then assert the BSY signal within a selection abort time of its most recent detection of being reselected; this is required for correct operation of the time-out procedure. The selection abort time is only 200 us which may be insufficient time for a printk() call. Move the diagnostics to the error paths. Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-09-28scsi: NCR5380: Don't clear busy flag when abort failsFinn Thain
When NCR5380_abort() returns FAILED, the driver forgets that the target is still busy. Hence, further commands may be sent to the target, which may fail during selection and produce the error message, "reselection after won arbitration?". Prevent this by leaving the busy flag set when NCR5380_abort() fails. Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-09-28scsi: NCR5380: Check for invalid reselection targetFinn Thain
The X3T9.2 specification (draft) says, under "6.1.4.1 RESELECTION", that "the initiator shall not respond to a RESELECTION phase if other than two SCSI ID bits are on the DATA BUS." This issue (too many bits set) has been observed in the wild, so add a check. Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-09-28scsi: NCR5380: Use DRIVER_SENSE to indicate valid sense dataFinn Thain
When sense data is valid, call set_driver_byte(cmd, DRIVER_SENSE). Otherwise some callers of scsi_execute() will ignore sense data. Don't set DID_ERROR or DID_RESET just because sense data is missing. Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-09-28scsi: NCR5380: Withhold disconnect privilege for REQUEST SENSEFinn Thain
This is mostly needed because an AztecMonster II target has been observed disconnecting REQUEST SENSE commands and then failing to reselect properly. Suggested-by: Michael Schmitz <schmitzmic@gmail.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-09-28scsi: NCR5380: Have NCR5380_select() return a boolFinn Thain
The return value is taken to mean "retry" or "don't retry". Change it to bool to improve readability. Fix related comments. No functional change. Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-09-28scsi: NCR5380: Reduce goto statements in NCR5380_select()Finn Thain
Replace a 'goto' statement with a simple 'return' where possible. This improves readability. No functional change. Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2018-09-28scsi: NCR5380: Clear all unissued commands on host resetHannes Reinecke
When doing a host reset we should be clearing all outstanding commands, not just the command triggering the reset. [mkp: adjusted Hannes' SoB address] Signed-off-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Cc: Ondrey Zary <linux@rainbow-software.org> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-11-14Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds
Pull SCSI updates from James Bottomley: "This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas, megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor updates. There's no major behaviour change or additions to the core in all of this, so the potential for regressions should be small (biggest potential being in the scsi error handler changes)" * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits) scsi: lpfc: Fix hard lock up NMI in els timeout handling. scsi: mpt3sas: remove a stray KERN_INFO scsi: mpt3sas: cleanup _scsih_pcie_enumeration_event() scsi: aacraid: use timespec64 instead of timeval scsi: scsi_transport_fc: add 64GBIT and 128GBIT port speed definitions scsi: qla2xxx: Suppress a kernel complaint in qla_init_base_qpair() scsi: mpt3sas: fix dma_addr_t casts scsi: be2iscsi: Use kasprintf scsi: storvsc: Avoid excessive host scan on controller change scsi: lpfc: fix kzalloc-simple.cocci warnings scsi: mpt3sas: Update mpt3sas driver version. scsi: mpt3sas: Fix sparse warnings scsi: mpt3sas: Fix nvme drives checking for tlr. scsi: mpt3sas: NVMe drive support for BTDHMAPPING ioctl command and log info scsi: mpt3sas: Add-Task-management-debug-info-for-NVMe-drives. scsi: mpt3sas: scan and add nvme device after controller reset scsi: mpt3sas: Set NVMe device queue depth as 128 scsi: mpt3sas: Handle NVMe PCIe device related events generated from firmware. scsi: mpt3sas: API's to remove nvme drive from sml scsi: mpt3sas: API 's to support NVMe drive addition to SML ...
2017-11-02License cleanup: add SPDX GPL-2.0 license identifier to files with no licenseGreg Kroah-Hartman
Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-31scsi: NCR5380: Suppress SDTR and WDTR message loggingFinn Thain
The 5380 drivers only support asynchronous transfers and the 5380 controllers only have narrow busses. Hence, the core driver will reject any SDTR and WDTR messages from target devices. Don't log this, it's expected behaviour. Also, fix the off-by-one array indices in the arguments to scmd_printk(). Tested-by: Stan Johnson <userm57@yahoo.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-08-25scsi: NCR5380: Move bus reset to host resetHannes Reinecke
The bus reset handler really is a host reset, so move it to eh_bus_reset_handler. Signed-off-by: Hannes Reinecke <hare@suse.com> Acked-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-01-31scsi: ncr5380: Improve target selection robustnessFinn Thain
Handle timeout or bus phase change errors that could occur when sending the IDENTIFY message. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-01-31scsi: ncr5380: Resolve various static checker warningsFinn Thain
Avoid various warnings from "make C=1" by annotating a couple of unlock-then-lock sequences, replacing a zero with NULL and correcting some type casts. Also avoid a warning from "make W=1" by adding braces. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-01-31scsi: ncr5380: Shorten host info string by removing unused option macrosFinn Thain
The DIFFERENTIAL and PARITY option macros are unused: no supported hardware uses differential signalling and the core driver never implemented parity checking. These options just waste space in the host info string. While we are here, fix a typo in the NCR5380_info() kernel-doc comment. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-12-08scsi: g_NCR5380: Use probe_irq_*() for IRQ probingOndrej Zary
Use standard probe_irq_on() and probe_irq_off() functions instead of own implementation. This prevents warning messages like this in the kernel log: genirq: Flags mismatch irq 1. 00000000 (NCR-probe) vs. 00000080 (i8042) Move the IRQ trigger code from NCR5380 to g_NCR5380 where it is used. Also clear interrupt flag before and after the probe. Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-11-08scsi: ncr5380: Suppress unhelpful "interrupt without IRQ bit" messageFinn Thain
If a NCR5380 host instance ends up on a shared interrupt line then this printk will be a problem. It is already a problem on some Mac models: when testing mac_scsi on a PowerBook 180 I found that PDMA transfers (but not PIO transfers) cause the message to be logged. These spurious interrupts don't appear to come from the DRQ signal from the 5380. And they don't happen at all on the Mac LC III. A comment in the NetBSD source code mentions this mystery. Testing seems to show that we can safely ignore these interrupts. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-11-08scsi: ncr5380: Use correct types for DMA routinesFinn Thain
Apply prototypes to get consistent function signatures for the DMA functions implemented in the board-specific drivers. To avoid using macros to alter actual parameters, some of those functions are reworked slightly. This is a step toward the goal of passing the board-specific routines to the core driver using an ops struct (as in a platform driver or library module). This also helps fix some inconsistent types: where the core driver uses ints (cmd->SCp.this_residual and hostdata->dma_len) for keeping track of transfers, certain board-specific routines used unsigned long. While we are fixing these function signatures, pass the hostdata pointer to DMA routines instead of a Scsi_Host pointer, for shorter and faster code. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Acked-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-11-08scsi: ncr5380: Pass hostdata pointer to register polling routinesFinn Thain
Pass a NCR5380_hostdata struct pointer to the board-specific routines instead of a Scsi_Host struct pointer. This reduces pointer chasing in the PIO and PDMA fast paths. The old way was a mistake because it is slow and the board-specific code is not concerned with the mid-layer. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-11-08scsi: ncr5380: Use correct types for device register accessorsFinn Thain
For timeout values adopt unsigned long, which is the type of jiffies etc. For chip register values and bit masks pass u8, which is the return type of readb, inb etc. For device register offsets adopt unsigned int, as it is suitable for adding to base addresses. Pass the NCR5380_hostdata pointer to the board-specific routines instead of the Scsi_Host pointer. The board-specific code is concerned with hardware and not with SCSI protocol or the mid-layer. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Acked-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-11-08scsi: ncr5380: Store IO ports and addresses in host private dataFinn Thain
The various 5380 drivers inconsistently store register pointers either in the Scsi_Host struct "legacy crap" area or in special, board-specific members of the NCR5380_hostdata struct. Uniform use of the latter struct makes for simpler and faster code (see the following patches) and helps to reduce use of the NCR5380_implementation_fields macro. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Acked-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-11-08scsi: ncr5380: Simplify register polling limitFinn Thain
When polling a device register under irq lock the polling loop terminates after a given number of jiffies. Make this timeout independent of the HZ setting. All 5380 drivers benefit from this patch, which optimizes the PIO fast path, because they all use PIO transfers (for phases other than DATA IN and DATA OUT). Some cards support only PIO transfers (even for DATA phases). CPU cycles are scarce on some of these systems, so a small improvement here makes a big difference. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-10-17scsi: NCR5380: no longer mark irq probing as __initArnd Bergmann
The g_NCR5380 has been converted to more regular probing, which means its probe function can now be invoked after the __init section is discarded, as pointed out by this kbuild warning: WARNING: drivers/scsi/built-in.o(.text+0x3a105): Section mismatch in reference from the function generic_NCR5380_isa_match() to the function .init.text:probe_intr() WARNING: drivers/scsi/built-in.o(.text+0x3a145): Section mismatch in reference from the function generic_NCR5380_isa_match() to the variable .init.data:probe_irq To make sure this works correctly in all cases, let's remove the __init and __initdata annotations. Fixes: a8cfbcaec0c1 ("scsi: g_NCR5380: Stop using scsi_module.c") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-09-14scsi: ncr5380: Improve interrupt latency during PIO tranfersFinn Thain
Large PIO transfers are broken up into chunks to try to avoid disabling local IRQs for long periods. But IRQs are still disabled for too long and this causes SCC FIFO overruns during serial port transfers. This patch reduces the PIO chunk size to reduce interrupt latency to something on the order of milliseconds, at the expense of additional CPU overhead from extra iterations of the NCR5380_main() loop. That CPU overhead is a problem for slow machines (e.g. mac_scsi on 25 MHz 68030) but these machines generally use PDMA not PIO. This patch doesn't make the overhead any worse on my Mac LC III (because it only gets about 510 accesses per ms). This patch decreases disk performance by a fraction of one percent for dmx3191d on my 333 MHz PowerPC 750. Other affected hardware (such as g_NCR5380 on x86) was not tested but 5380 ISA cards generally use PDMA and not PIO. [mkp: fix whitespace] Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Laurence Oberman <loberman@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-08-31scsi: ncr5380: Avoid a compiler warningFinn Thain
With commit 3a0f64bfa907 ("mac_scsi: Fix pseudo DMA implementation") some versions of gcc now warn: In file included from drivers/scsi/mac_scsi.c:335: drivers/scsi/NCR5380.h:295: warning: `NCR5380_poll_politely' declared inline after being called drivers/scsi/NCR5380.h:295: warning: previous declaration of `NCR5380_poll_politely' was here Avoid this by defining NCR5380_poll_politely() in NCR5380.h. [mkp: checkpatch warnings] Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Tested-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-04-11ncr5380: Call complete_cmd() for disconnected commands on bus resetFinn Thain
I'm told that some targets are liable to disconnect a REQUEST SENSE command. Theoretically this would cause a command undergoing autosense to be moved onto the disconnected list. The bus reset handler must call complete_cmd() for these commands, otherwise the hostdata->sensing pointer will not get cleared. That would cause autosense processing to stall and a timeout or an incorrect scsi_eh_restore_cmnd() would eventually follow. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reported-by: Michael Schmitz <schmitzmic@gmail.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-04-11ncr5380: Remove DONT_USE_INTR and AUTOPROBE_IRQ macrosFinn Thain
Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-04-11ncr5380: Remove remaining register storage qualifiersFinn Thain
Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-04-11ncr5380: Fix register decoding for debuggingFinn Thain
Decode all bits in the chip registers. They are all useful at times. Fix printk severity so that this output can be suppressed along with the other debugging output. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-04-11ncr5380: Reduce max_lun limitFinn Thain
The driver has a limit of eight LUs because of the byte-sized bitfield that is used for busy flags. That means the maximum LUN is 7. The default is 8. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-04-11ncr5380: Remove disused atari_NCR5380.c core driverFinn Thain
Now that atari_scsi and sun3_scsi have been converted to use the NCR5380.c core driver, remove atari_NCR5380.c. Also remove the last vestiges of its Tagged Command Queueing implementation from the wrapper drivers. The TCQ support in atari_NCR5380.c is abandoned by this patch. It is not merged into the remaining core driver because, 1) atari_scsi defines SUPPORT_TAGS but leaves FLAG_TAGGED_QUEUING disabled by default, which indicates that it is mostly undesirable. 2) I'm told that it doesn't work correctly when enabled. 3) The algorithm does not make use of block layer tags which it will have to do because scmd->tag is deprecated. 4) sun3_scsi doesn't define SUPPORT_TAGS at all, yet the the SUPPORT_TAGS macro interacts with the CONFIG_SUN3 macro in 'interesting' ways. 5) Compile-time configuration with macros like SUPPORT_TAGS caused the configuration space to explode, leading to untestable and unmaintainable code that is too hard to reason about. The merge_contiguous_buffers() code is also abandoned. This was unused by sun3_scsi. Only atari_scsi used it and then only on TT, because only TT supports scatter/gather. I suspect that the TT would work fine with ENABLE_CLUSTERING instead. If someone can benchmark the difference then perhaps the merge_contiguous_buffers() code can be be justified. Until then we are better off without the extra complexity. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-04-11sun3_scsi: Adopt NCR5380.c core driverFinn Thain
Add support for the custom Sun 3 DMA logic to the NCR5380.c core driver. This code is copied from atari_NCR5380.c. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-04-11atari_scsi: Adopt NCR5380.c core driverFinn Thain
Add support for the Atari ST DMA chip to the NCR5380.c core driver. This code is copied from atari_NCR5380.c. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-04-11ncr5380: Merge DMA implementation from atari_NCR5380 core driverFinn Thain
Adopt the DMA implementation from atari_NCR5380.c. This means that atari_scsi and sun3_scsi can make use of the NCR5380.c core driver and the atari_NCR5380.c driver fork can be made redundant. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-04-11ncr5380: Adopt uniform DMA setup conventionFinn Thain
Standardize the DMA setup hooks so that the DMA implementation in atari_NCR5380.c can be reconciled with pseudo DMA implementation in NCR5380.c. Calls to NCR5380_dma_recv_setup() and NCR5380_dma_send_setup() return a negative value on failure, zero on PDMA transfer success and a positive byte count for DMA setup success. This convention is not entirely new, but is now applied consistently. Also remove a pointless Status Register access: the *phase assignment is redundant because after NCR5380_transfer_dma() returns control to NCR5380_information_transfer(), that routine then returns control to NCR5380_main(), which means *phase is dead. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-04-11ncr5380: Use DMA hooks for PDMAFinn Thain
Those wrapper drivers which use DMA define the REAL_DMA macro and those which use pseudo DMA define PSEUDO_DMA. These macros need to be removed for a number of reasons, not least of which is to have drivers share more code. Redefine the PDMA send and receive hooks as DMA setup hooks, so that the DMA code can be shared by all 5380 wrapper drivers. This will help to reunify the forked core driver. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-04-11ncr5380: Remove BOARD_REQUIRES_NO_DELAY macroFinn Thain
The io_recovery_delay macro is intended to insert a microsecond delay between the chip register accesses that begin a DMA operation. This is reportedly needed for some ISA boards. Reverse the sense of the macro test so that in the common case, where no delay is required, drivers need not define the macro. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-04-11ncr5380: Remove PSEUDO_DMA macroFinn Thain
For those wrapper drivers which only implement Programmed IO, have NCR5380_dma_xfer_len() evaluate to zero. That allows PDMA to be easily disabled at run-time and so the PSEUDO_DMA macro is no longer needed. Also remove the spin counters used for debugging pseudo DMA drivers. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-04-11ncr5380: Disable the DMA errata workaround flag by defaultFinn Thain
The only chip that needs the workarounds enabled is an early NMOS device. That means that the common case is to disable them. Unfortunately the sense of the flag is such that it has to be set for the common case. Rename the flag so that zero can be used to mean "no errata workarounds needed". This simplifies the code. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-04-11ncr5380: Remove REAL_DMA and REAL_DMA_POLL macrosFinn Thain
For the NCR5380.c core driver, these macros are never used. If REAL_DMA were to be defined, compilation would fail. For the atari_NCR5380.c core driver, REAL_DMA is always defined. Hence these macros are pointless. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-04-11ncr5380: Remove FLAG_NO_PSEUDO_DMA where possibleFinn Thain
Drivers that define PSEUDO_DMA also define NCR5380_dma_xfer_len. The core driver must call NCR5380_dma_xfer_len which means FLAG_NO_PSEUDO_DMA can be eradicated from the core driver. dmx3191d doesn't define PSEUDO_DMA and has no use for FLAG_NO_PSEUDO_DMA, so remove it there also. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-03-01ncr5380: Call scsi_eh_prep_cmnd() and scsi_eh_restore_cmnd() as and when ↵Finn Thain
appropriate This bug causes the wrong command to have its sense pointer overwritten, which sometimes leads to a NULL pointer deref. Fix this by checking which command is being requeued before restoring the scsi_eh_save data. It turns out that some targets will disconnect a REQUEST SENSE command. The autosense algorithm doesn't anticipate this. Hence multiple commands can end up undergoing autosense simultaneously, and they will all try to use the same scsi_eh_save struct, which won't work. Defer autosense when the scsi_eh_save storage is in use by another command. Fixes: f27db8eb98a1 ("ncr5380: Fix autosense bugs") Reported-and-tested-by: Michael Schmitz <schmitzmic@gmail.com> Cc: <stable@vger.kernel.org> # 4.5 Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-03-01ncr5380: Fix NCR5380_select() EH checks and result handlingFinn Thain
Add missing checks for EH abort during arbitration and selection. Rework the handling of NCR5380_select() result to improve clarity. Fixes: 707d62b37fbb ("ncr5380: Fix EH during arbitration and selection") Tested-by: Michael Schmitz <schmitzmic@gmail.com> Cc: <stable@vger.kernel.org> # 4.5 Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-03-01ncr5380: Forget aborted commandsFinn Thain
The list structures and related logic used in the NCR5380 driver mean that a command cannot be queued twice (i.e. can't appear on more than one queue and can't appear on the same queue more than once). The abort handler must forget the command so that the mid-layer can re-use it. E.g. the ML may send it back to the LLD via via scsi_eh_get_sense(). Fix this and also fix two error paths, so that commands get forgotten iff completed. Fixes: 8b00c3d5d40d ("ncr5380: Implement new eh_abort_handler") Tested-by: Michael Schmitz <schmitzmic@gmail.com> Cc: <stable@vger.kernel.org> # 4.5 Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-03-01ncr5380: Dont re-enter NCR5380_select()Finn Thain
Calling NCR5380_select() from the abort handler causes various problems. Firstly, it means potentially re-entering NCR5380_select(). Secondly, it means that the lock is released, which permits the EH handlers to be re-entered. The combination results in crashes. Don't do it. Fixes: 8b00c3d5d40d ("ncr5380: Implement new eh_abort_handler") Reported-and-tested-by: Michael Schmitz <schmitzmic@gmail.com> Cc: <stable@vger.kernel.org> # 4.5 Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-03-01ncr5380: Dont release lock for PIO transferFinn Thain
The calls to NCR5380_transfer_pio() for DATA IN and DATA OUT phases will modify cmd->SCp.this_residual, cmd->SCp.ptr and cmd->SCp.buffer. That works as long as EH does not intervene, which became possible in atari_NCR5380.c when I changed the locking to bring it closer to NCR5380.c. If error recovery aborts the command, the scsi_cmnd in question and its buffer will be returned to the mid-layer. So the transfer has to cease, but it can't be stopped by the initiator because the target controls the bus phase. The problem does not arise if the lock is not released. That was fine for atari_scsi, because it implements DMA. For the other drivers, we have to release the lock and re-enable interrupts for long PIO data transfers. The solution is to split the transfer into small chunks. In between chunks the main loop releases the lock and re-enables interrupts. Thus interrupts can be serviced and eh_bus_reset_handler can intervene if need be. This fixes an oops in NCR5380_transfer_pio() that can happen when the EH abort handler is invoked during DATA IN or DATA OUT phase. Fixes: 11d2f63b9cf5 ("ncr5380: Change instance->host_lock to hostdata->lock") Reported-and-tested-by: Michael Schmitz <schmitzmic@gmail.com> Cc: <stable@vger.kernel.org> # 4.5 Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-03-01ncr5380: Correctly clear command pointers and lists after bus resetFinn Thain
Commands subject to exception handling are to be returned to the scsi mid-layer. Make sure that the various command pointers and command lists in the low-level driver are correctly cleansed of affected commands. This fixes some bugs that I accidentally introduced in v4.5-rc1 including the removal of INIT_LIST_HEAD for the 'autosense' and 'disconnected' command lists, and the possible NULL pointer dereference in NCR5380_bus_reset() that was reported by Dan Carpenter. hostdata->sensing may also point to an affected command so this pointer also has to be cleared. The abort handler calls complete_cmd() to take care of this; let's have the bus reset handler do the same. The issue queue may also contain an affected command. If so, remove it. This also follows the abort handler logic. Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: 62717f537e1b ("ncr5380: Implement new eh_bus_reset_handler") Tested-by: Michael Schmitz <schmitzmic@gmail.com> Cc: <stable@vger.kernel.org> # 4.5 Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>