| Age | Commit message (Collapse) | Author |
|---|
|
This line is indented too far so it's a bit confusing.
Link: https://lore.kernel.org/r/20191004100615.GA823@mwanda
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If any faulty application issues an NVMe Encapsulated commands to HBA which
doesn't support NVMe protocol then driver should return the command as
invalid with the following message.
"HBA doesn't support NVMe. Rejecting NVMe Encapsulated request."
Otherwise below page fault kernel panic will be observed while building the
PRPs as there is no PRP pools allocated for the HBA which doesn't support
NVMe drives.
RIP: 0010:_base_build_nvme_prp+0x3b/0xf0 [mpt3sas]
Call Trace:
_ctl_do_mpt_command+0x931/0x1120 [mpt3sas]
_ctl_ioctl_main.isra.11+0xa28/0x11e0 [mpt3sas]
? prepare_to_wait+0xb0/0xb0
? tty_ldisc_deref+0x16/0x20
_ctl_ioctl+0x1a/0x20 [mpt3sas]
do_vfs_ioctl+0xaa/0x620
? vfs_read+0x117/0x140
ksys_ioctl+0x67/0x90
__x64_sys_ioctl+0x1a/0x20
do_syscall_64+0x60/0x190
entry_SYSCALL_64_after_hwframe+0x44/0xa9
[mkp: tweaked error string]
Link: https://lore.kernel.org/r/1568379890-18347-12-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Return the diag buffer release command with -EINVAL status if the buffer is
already released.
Link: https://lore.kernel.org/r/1568379890-18347-10-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Added a new status flag named MPT3_DIAG_BUFFER_IS_APP_OWNED and it will set
whenever application registers the diag buffer & it will be cleared when
application unregisters the buffer.
When this flag is enabled, and if application issues diag buffer register
command without releasing the buffer, then register command will be failed
with -EINVAL status by saying that this buffer is already registered by the
application.
When user issues a trace buffer register command through sysfs parameter,
and if trace buffer is in released stated but not yet unregistered by the
application which was owning it, then driver will unregister the buffer by
itself and freshly register the 1MB sized trace buffer with the HBA
firmware.
Link: https://lore.kernel.org/r/1568379890-18347-9-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The diag buffer which is allocated during driver load time or through sysfs
parameter is marked as driver allocated diag buffer.
MPT3_DIAG_BUFFER_IS_DRIVER_ALLOCATED bit will be set for this buffer.
This buffer won't be de-allocated even when application issues unregister
command, driver just clears the registered status bit. Same buffer will be
reused while re-registering the same diag buffer type by any application.
While re-registering the same diag buffer type application has to register
with the same size that the buffer was allocated during driver load
time. This buffer size can be read by the application by issuing diag
'query' command.
This always makes sure that the memory is available for applications for
collecting the firmware logs. Only thing is that this won't allow the
application to re-register the diag buffer with different size, but the
buffer size which is allocated during driver load time will be enough for
most of the cases for collecting the firmware logs.
Link: https://lore.kernel.org/r/1568379890-18347-8-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Clear MPT3_DIAG_BUFFER_IS_RELEASED bit once diag buffer is re-registered
after reading the buffer, else driver won't release the buffer and return
the 'diag release' command with -EINVAL status saying that buffer is
already released.
Link: https://lore.kernel.org/r/1568379890-18347-7-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Application A has registered a diag buffer and looking for particular event
to happen to release & read the trace buffer. Meanwhile application B has
unregistered the diag buffer and now Application A can't get the required
diag buffer. So proper diag buffer ownership is missing.
Each application has to maintain its own Unique ID. Now driver has to save
the Application's UniqueID for each diag buffer type when diag buffer is
registered. And driver has to allow 'release', 'read' & 'unregister' diag
commands only if application's UniqueID matches with saved UniqueID for the
corresponding diag buffer type.
When diag buffer is registered by the driver, then the UniqueID saved by
the driver is "BRCM" (i.e. 0x4252434D) for SAS3 and above generations HBA
devices. For SAS2 HBAs, driver keeps the legacy UniqueID 0x07075900 for
maintaining compatibility with the legacy SAS2 application and this
improvement won't be applicable for SAS2 HBA devices.
Any application can own the buffer registered by the driver by sending
diag register request to driver with same buffer type and size
(Application can get the buffer size by sending 'query' command). Then
driver changes the ownership of the buffer by saving application's
UniqueID for that corresponding buffer type.
Also, application can re-register the diag buffer with same size without
un-registering it, but diag buffer should be released before re-registering
it. By allowing this, driver no need to deallocate and allocate a new
buffer for re-register command, same buffer can be re-used.
Link: https://lore.kernel.org/r/1568379890-18347-6-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Memory leak can happen when diag buffer is released but not unregistered
(where buffer is deallocated) by the user. During module unload time driver
is not deallocating the buffer if the buffer is in released state.
Deallocate the diag buffer during module unload time without any diag
buffer status checks.
Link: https://lore.kernel.org/r/1568379890-18347-5-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When user issues diag register command from application with required size,
and if driver unable to allocate the memory, then it will fail the register
command. While failing the register command, driver is not currently
clearing MPT3_CMD_PENDING bit in ctl_cmds.status variable which was set
before trying to allocate the memory. As this bit is set, subsequent
register command will be failed with BUSY status even when user wants to
register the trace buffer will less memory.
Clear MPT3_CMD_PENDING bit in ctl_cmds.status before returning the diag
register command with no memory status.
Link: https://lore.kernel.org/r/1568379890-18347-4-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Display message before releasing the diag buffer so that user knows which
event caused the release of diag buffer.
Releasing of diag buffer means HBA firmware stops posting the firmware logs
on the registered diag buffer.
Link: https://lore.kernel.org/r/1568379890-18347-3-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently if user wishes to enable the host trace buffer during driver load
time, then user has to load the driver with module parameter
'diag_buffer_enable' set to one.
Alternatively now the user can enable host trace buffer by enabling the
following fields in manufacturing page11 in NVDATA (nvdata xml is used
while building HBA firmware image):
* HostTraceBufferMaxSizeKB - Maximum trace buffer size in KB that host can
allocate,
* HostTraceBufferMinSizeKB - Minimum trace buffer size in KB atleast host
should allocate,
* HostTraceBufferDecrementSizeKB - size by which host can reduce from
buffer size and retry the buffer allocation
when buffer allocation failed with previous
calculated buffer size.
The driver will register the trace buffer automatically without any module
parameter during boot time when above fields are enabled in manufacturing
page11 in HBA firmware.
Driver follows the following algorithm for enabling the host trace buffer
during driver load time:
* If user has loaded the driver with module parameter 'diag_buffer_enable'
set to one, then driver allocates 2MB buffer and registers this buffer
with HBA firmware for capturing the firmware trace logs.
* Else driver reads manufacture page11 data and checks whether
HostTraceBufferMaxSizeKB filed is zero or not?
- If HostTraceBufferMaxSizeKB is non-zero then driver tries to allocate
HostTraceBufferMaxSizeKB size of memory. If the buffer allocation is
successful, then it will register this buffer with HBA firmware, else
in a loop the driver will try again by reducing the current buffer size
with HostTraceBufferDecrementSizeKB size until memory allocation is
successful or buffer size falls below HostTraceBufferMinSizeKB. If the
memory allocation is successful, then the buffer will be registered
with the firmware. Else, if the buffer size falls below the
HostTraceBufferMinSizeKB, then driver won't register trace buffer with
HBA firmware.
- If HostTraceBufferMaxSizeKB is zero, then driver won't register trace
buffer with HBA firmware.
Link: https://lore.kernel.org/r/1568379890-18347-2-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch provides a module parameter and sysfs interface to select
whether the queue depth for each device should be based on the
protocol-specific value set by the driver (the default) or the maximum
supported by the controller (can_queue).
Although we have a sysfs interface per sdev to change the queue depth
of individual scsi devices, this implementation provides a single
sysfs entry per shost to switch between the controller max and the
driver default.
[mkp: tweaked commit desc]
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently with sysfs parameter "drv_support_bitmap" driver exposes whether
driver supports toolbox memory move command or not.
And application should issue the toolbox memory move command only if driver
tell that memory move tool box command is supported through this sysfs
parameter.
In future we can utilize this sysfs parameter if any new feature is added
and need to notify the same to applications.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Host uses the Memory Move Tool to copy data from any source/destination
combination of system memory and IOC memory.
Memory Move Tool box request contains two SGE fields, First SGE field must
contains the source buffer details described by an MPI Simple SGE. The
second SGE field must contains the destination buffer details described by
an MPI Simple SGE.
Source -> Destination
1. IOC -> IOC (Both the SGE's will be filled by application)
2. HOST -> HOST (Both the SGE's will be filled by the host,
application should give sgl_offset to first SGE offset)
3. IOC -> HOST (Application will fill the first SGE and set the
sgl_offset to second SGE and hence driver fills
the second SGE)
4. HOST -> IOC (Application will fill IOC buffer information in the
first SGE and set the sgl_offset to second SGE.
Then driver will fill the second SGE with Host buffer
information and just before posting the command to the
firmware, driver will swap these two SGEs so that first
SGE contains the HOST buffer information and second SGE
contains the IOC information.
Driver has to take care only of the 4th case, other three cases are by
default supported by the current driver design.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
SES device of managed PCIe switch will be enumerated same as NVMe drives.
The device info type for this SES device is
MPI26_PCIE_DEVINFO_SCSI (0x4),
whereas the device info type for NVMe drives is
MPI26_PCIE_DEVINFO_NVME (0x3).
Based on this device info type driver determines whether the device is NVMe
drive or a SES device of a managed PCIe switch.
This SES device doesn't have the PCIe device page 2 information like NVMe
drives, so driver won't read PCIe device page 2 information for SES device.
This SES device uses only IEEE SGL's, So driver build's IEEE SGL's whenever
it receives any SCSI commands for this SES device.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Driver gets a request frame from the free pool of DMA-able request frames
and fill in the required information and pass the address of the frame to
IOC/FW to pull the complete request frame. In certain places the driver
used the request frame allocated from the free pool without completely
clearing the previous data stored in it. The request contents were cleared
only for the size of the new request to be issued and that left out some
stale data in the unused part of the request. Though the IOC/FW is not
expected to access the request beyond the specified size, it is good
practice to clear complete request message frame.
So reinitialize the complete request message frame with 0s before using
it.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
PCIe Lane margin tool box request requires IEEE sgl's and hence driver
fills the SGL field with IEEE sgl's while issuing the PCIe Lane margin
ioctl request to the HBA firmware.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We can request task management IOCTL command(MPI2_FUNCTION_SCSI_TASK_MGMT)
to /dev/mpt3ctl. If the given task_type is either abort task or query
task, it may need a field named "Initiator Port Transfer Tag to Manage" in
the IU.
Current code does not support to check target IPTT tag from the tm_request.
This patch introduces to check TaskMID given from the userspace as a target
tag. We have a rule of relationship between
(struct request *req->tag) and smid in mpt3sas_base.c:
3318 u16
3319 mpt3sas_base_get_smid_scsiio(struct MPT3SAS_ADAPTER *ioc, u8 cb_idx,
3320 struct scsi_cmnd *scmd)
3321 {
3322 struct scsiio_tracker *request = scsi_cmd_priv(scmd);
3323 unsigned int tag = scmd->request->tag;
3324 u16 smid;
3325
3326 smid = tag + 1;
So if we want to abort a request tagged #X, then we can pass (X + 1) to
this IOCTL handler. Otherwise, user space just can pass 0 TaskMID to abort
the first outstanding smid which is legacy behaviour.
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: James E.J. Bottomley <jejb@linux.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: MPT-FusionLinux.pdl@broadcom.com
Signed-off-by: Minwoo Im <minwoo.im@samsung.com>
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There is a copy and paste bug here. It uses EVENT_TRIGGERS size instead of
SCSI_TRIGGERS size but fortunately both size are 84 bytes so it doesn't
affect runtime.
These days the preferred style is to just say sizeof(object) instead of
sizeof(type) so I have updated the function to the latest style as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use existing macros. No functional change.
[mkp: typo]
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This code refactoring introduces function pointers.
Host uses Request Descriptors of different types for posting an entry onto
a request queue. Based on controller type and capabilities, host can also
use atomic descriptors other than normal descriptors. Using function
pointer will avoid if-else statements
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In _ctl_ioctl_main(), 'ioctl_header' is fetched the first time from
userspace. 'ioctl_header.ioc_number' is then checked. The legal result is
saved to 'ioc'. Then, in condition MPT3COMMAND, the whole struct is fetched
again from the userspace. Then _ctl_do_mpt_command() is called, 'ioc' and
'karg' as inputs.
However, a malicious user can change the 'ioc_number' between the two
fetches, which will cause a potential security issues. Moreover, a
malicious user can provide a valid 'ioc_number' to pass the check in first
fetch, and then modify it in the second fetch.
To fix this, we need to recheck the 'ioc_number' in the second fetch.
Signed-off-by: Gen Zhang <blackgod016574@gmail.com>
Acked-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
No functional changes. This section of code "wait for IOC to be
operational" is used in many places across the driver. Factor this code
out into a new mpt3sas_wait_for_ioc().
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Added new #define variable IOC_OPERATIONAL_WAIT_COUNT and it replaces hard
coded value '10' in all the places where driver is waiting for the IOC to
become operational.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Switch from the legacy PCI DMA API to the generic DMA API.
Also simplify setting the DMA mask a bit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use a more common logging style.
Done using the perl script below and some typing
$ git grep --name-only -w MPT3SAS_FMT -- "*.c" | \
xargs perl -i -e 'local $/; while (<>) { s/\bpr_(info|err|notice|warn)\s*\(\s*MPT3SAS_FMT\s*("[^"]+"(?:\s*\\?\s*"[^"]+"\s*){0,5}\s*),\s*ioc->name\s*/ioc_\1(ioc, \2/g; print;}'
Miscellanea for these conversions:
o Coalesce formats
o Realign arguments
o Remove unnecessary parentheses
o Use casts to u64 instead of unsigned long long where appropriate
o Convert broken pr_info uses to pr_cont
o Fix broken format string concatenation with line continuations and
excess whitespace
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Avoids that warnings about the kernel headers appear when building with
W=1. Remove useless "@Returns - Nothing" clauses. Change "@Return - " into
"Return: ".
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
and mpt3sas_ctl_reset_handler()
Split each of these functions in three functions - one function per reset
phase. This patch does not change any functionality but makes the code
easier to read.
Note: it is much easier to review the git diff -w output after having
applied this patch than by reviewing the patch itself.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch avoids that gcc complains about switch/case fall-through
when building with W=1.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
commands during controller reset.
When an ioctl is sent to FW, and if there is a controller reset issued
before ioctl gets completed, then in controller reset path all the pending
ioctl commands are terminated from "mpt3sas_ctl_reset_handler" function.
This will wake up the waiting ioctl commands in ioctl path and print
timeouts which are actually not timeouts.
Introduced "mpt3sas_base_check_cmd_timeout" function to check and print
whether command got timed out (or) terminated due to Host reset.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
1) Manufacturing Page 11 contains parameters to control internal
firmware behavior. Based on AddlFlags2 field FW/Driver behaviour can
be changed, (flag tm_custom_handling is used for this)
a) For PCIe device, protocol level reset should be used if flag
tm_custom_handling is 0. Since Abort Task Set, LUN reset and Target
reset will result in a protocol level reset. Drivers should issue
only one type of this reset, if that fails then it should escalate to
a controller reset (diag reset/OCR).
b) If the driver has control over the TM reset timeout value, then
driver should use the value exposed in PCIe Device Page 2 for pcie
device (field ControllerResetTO).
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch fixes sparse warnings and bugs on big endian systems.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
controllers.
Sending I/O through 32 bit descriptors to Ventura series of controller
results in IO timeout on certain conditions. This error only occurs on
systems with high I/O activity.
Changes in this patch will prevent driver from using 32 bit descriptor
and use 64 bit Descriptors
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual driver suspects: arcmsr,
scsi_debug, mpt3sas, lpfc, cxlflash, qla2xxx, aacraid, megaraid_sas,
hisi_sas.
We also have a rework of the libsas hotplug handling to make it more
robust, a slew of 32 bit time conversions and fixes, and a host of the
usual minor updates and style changes. The biggest potential for
regressions is the libsas hotplug changes, but so far they seem stable
under testing"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (313 commits)
scsi: qla2xxx: Fix logo flag for qlt_free_session_done()
scsi: arcmsr: avoid do_gettimeofday
scsi: core: Add VENDOR_SPECIFIC sense code definitions
scsi: qedi: Drop cqe response during connection recovery
scsi: fas216: fix sense buffer initialization
scsi: ibmvfc: Remove unneeded semicolons
scsi: hisi_sas: fix a bug in hisi_sas_dev_gone()
scsi: hisi_sas: directly attached disk LED feature for v2 hw
scsi: hisi_sas: devicetree: bindings: add LED feature for v2 hw
scsi: megaraid_sas: NVMe passthrough command support
scsi: megaraid: use ktime_get_real for firmware time
scsi: fnic: use 64-bit timestamps
scsi: qedf: Fix error return code in __qedf_probe()
scsi: devinfo: fix format of the device list
scsi: qla2xxx: Update driver version to 10.00.00.05-k
scsi: qla2xxx: Add XCB counters to debugfs
scsi: qla2xxx: Fix queue ID for async abort with Multiqueue
scsi: qla2xxx: Fix warning for code intentation in __qla24xx_handle_gpdb_event()
scsi: qla2xxx: Fix warning during port_name debug print
scsi: qla2xxx: Fix warning in qla2x00_async_iocb_timeout()
...
|
|
Performance improvement using block layer tag.
Curent driver gets scsiio tracker and free smid from link list and array
based tracking managed by driver. Accessing list in main io path is
performance pentaly because of protection using spinlock
"scsi_lookup_lock".
In this patch:
1. Driver removes all link list access from main io path and
use scmd->request->tag to get free smid.
2. Instead of holding 'struct scsiio_tracker' in its own pool
driver can embed it into the scsi command.
Driver provides cmd_size in scsi_host_template, so that struct
scsiio_tracker is preallocated by scsi mid layer for each scsi command.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Move the check for outstanding commands out of the function allowing us
to simplify the overall code.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
ioctl passthrough commands require a SCSIIO smid, but cannot easily
integrate with the block layer. But the driver already has reserved some
SCSIIO smids and we're only ever allowing one ioctl command at a time we
can use the first reserved smid for ioctl commands.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
* Added debug prints for pcie devices in ioctl debug path. Which
will be helpful for debugging.
* Added PCIe device support for ioctl BTDHMAPPING ioctl.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
* Mpt3sas driver uses the NVMe Encapsulated Request message to send an
NVMe command to an NVMe device attached to the IOC.
* Normal I/O commands like reads and writes are passed to the
controller as SCSI commands and the controller has the ability to
translate the commands to NVMe equivalent.
* This encapsulated NVMe command is used by applications to send
direct NVMe commands to NVMe drives.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
* Added support for translating the SGLs associated with incoming
commands either to IEE SGL or NVMe PRPs for NVMe devices.
* The hardware translation of IEEE SGL to NVMe PRPs has limitations
and if a command cannot be translated by hardware then it will go to
firmware and the firmware needs to translate it. This will have a
performance impact. To avoid that, the driver proactively checks
whether the translation will be done in hardware or not. If not, then
driver translates.
[mkp: clarified commit message]
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Since right after the user copy, we are going to memset(&karg, 0,
sizeof(karg)), the copy_from_user is redundant
Signed-off-by: Meng Xu <mengxu.gatech@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix typos and add the following to the scripts/spelling.txt:
overwritting||overwriting
Link: http://lkml.kernel.org/r/1481573103-11329-29-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Small glitch/degraded performance in Crusader is improved with SAS
drives by removing unnecessary spinlocks while clearing scsi command in
drivers internal lookup table.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch adds support for request iopriority handling in the mpt3sas
layer. This works only when a ATA device is behind the SATL. The ATA
device also has to indicate that it supports command priorities in the
identify information that is pulled from the SATL.
Signed-off-by: Adam Manzanares <adam.manzanares@wdc.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
SAS35 devices.
Support Atomic Request Descriptors for Ventura/SAS35 devices.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Added Device ID's for SAS35 devices (Ventura, Crusader, Harpoon &
Tomcat) and updated mpi header file for the same. Also added
"is_gen35_ioc" to MPT3SAS_ADAPTER structure for identifying SAS35 adapters.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When device missing event arrives, device_remove_in_progress bit will be
set and hence driver has to stop sending IOCTL commands.Now the check has
been added in IOCTL path to test device_remove_in_progress bit is set, if
so then IOCTL will be failed printing failure message.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Trivial non-functional changes for a couple annoying things:
1) Functions local to files are not declared static, which is
frustrating when reading the code because it's non-obvious at first
glance what's actually called from other files.
2) Set-but-unused variables abound, presumably to mask -Wunused-result
errors in the past. None of these are flagged today though (with one
exception noted below), so remove them.
Fixing (2) exposed the fact that we improperly ignore the return value
of scsi_device_reprobe() in _scsih_reprobe_lun(). Fixing the calling
code to deal with the potential error is non-trivial, so for now just
WARN().
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
