| Age | Commit message (Collapse) | Author |
|---|
|
A left shift must shift less than the bit width of the left argument.
Avoid triggering undefined behavior if ha->mbx_count == 32.
This patch avoids that UBSAN reports the following complaint:
UBSAN: Undefined behaviour in drivers/scsi/qla2xxx/qla_isr.c:275:14
shift exponent 32 is too large for 32-bit type 'int'
Call Trace:
dump_stack+0x4e/0x6c
ubsan_epilogue+0xd/0x3b
__ubsan_handle_shift_out_of_bounds+0x112/0x14c
qla2x00_mbx_completion+0x1c5/0x25d [qla2xxx]
qla2300_intr_handler+0x1ea/0x3bb [qla2xxx]
qla2x00_mailbox_command+0x77b/0x139a [qla2xxx]
qla2x00_mbx_reg_test+0x83/0x114 [qla2xxx]
qla2x00_chip_diag+0x354/0x45f [qla2xxx]
qla2x00_initialize_adapter+0x2c2/0xa4e [qla2xxx]
qla2x00_probe_one+0x1681/0x392e [qla2xxx]
pci_device_probe+0x10b/0x1f1
driver_probe_device+0x21f/0x3a4
__driver_attach+0xa9/0xe1
bus_for_each_dev+0x6e/0xb5
driver_attach+0x22/0x3c
bus_add_driver+0x1d1/0x2ae
driver_register+0x78/0x130
__pci_register_driver+0x75/0xa8
qla2x00_module_init+0x21b/0x267 [qla2xxx]
do_one_initcall+0x5a/0x1e2
do_init_module+0x9d/0x285
load_module+0x20db/0x38e3
SYSC_finit_module+0xa8/0xbc
SyS_finit_module+0x9/0xb
do_syscall_64+0x77/0x271
entry_SYSCALL64_slow_path+0x25/0x25
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We wanted to exit the loop with "div" set to zero, but instead, if we
don't hit the break then "div" is -1 when we finish the loop. It leads
to an array underflow a few lines later.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When a request times out we set the io_req flag BNX2FC_FLAG_IO_COMPL so
that if a subsequent completion comes in on that task ID we will ignore
it. The issue is that in the check for this flag there is a missing
return so we will continue to process a request which may have already
been returned to the ownership of the SCSI layer. This can cause
unpredictable results.
Solution is to add in the missing return.
[mkp: typo plus title shortening]
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The pointer ln is assigned a value that is never read, it is re-assigned
a new value in the list_for_each loop hence the initialization is
redundant and can be removed.
Cleans up clang warning:
drivers/scsi/csiostor/csio_lnode.c:117:21: warning: Value stored to 'ln'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
WRITE_SAME command is not supported by UFS. Enable a quirk for the upper
level drivers to not send WRITE SAME command.
[mkp: botched patch, applied by hand]
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The fcp_rsp_info structure as defined in the FC spec has an initial 3
bytes reserved field. The ibmvfc driver mistakenly defined this field as
4 bytes resulting in the rsp_code field being defined in what should be
the start of the second reserved field and thus always being reported as
zero by the driver.
Ideally, we should wire ibmvfc up with libfc for the sake of code
deduplication, and ease of maintaining standardized structures in a
single place. However, for now simply fixup the definition in ibmvfc for
backporting to distros on older kernels. Wiring up with libfc will be
done in a followup patch.
Cc: <stable@vger.kernel.org>
Reported-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch fixes memory corrpution while performing HBA Reset test.
Following stack trace is seen:
[ 466.397219] BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
[ 466.433669] IP: [<ffffffffc06f5dd0>] qlt_free_session_done+0x260/0x5f0 [qla2xxx]
[ 466.467731] PGD 0
[ 466.476718] Oops: 0000 [#1] SMP
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
cpu_msix_table is allocated to store online cpus, but pci_irq_get_affinity
may return cpu_possible_mask which is then used to access cpu_msix_table.
That causes bad user experience. Fix limits access to only online cpus,
I've also added an additional test to protect from an unlikely change in
cpu_online_mask.
[mkp: checkpatch]
Fixes: 1d55abc0e98a ("scsi: mpt3sas: switch to pci_alloc_irq_vectors")
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"This includes some infrastructure changes in the PM core, mostly
related to integration between runtime PM and system-wide suspend and
hibernation, plus some driver changes depending on them and fixes for
issues in that area which have become quite apparent recently.
Also included are changes making more x86-based systems use the Low
Power Sleep S0 _DSM interface by default, which turned out to be
necessary to handle power button wakeups from suspend-to-idle on
Surface Pro3.
On the cpufreq front we have fixes and cleanups in the core, some new
hardware support, driver updates and the removal of some unused code
from the CPU cooling thermal driver.
Apart from this, the Operating Performance Points (OPP) framework is
prepared to be used with power domains in the future and there is a
usual bunch of assorted fixes and cleanups.
Specifics:
- Define a PM driver flag allowing drivers to request that their
devices be left in suspend after system-wide transitions to the
working state if possible and add support for it to the PCI bus
type and the ACPI PM domain (Rafael Wysocki).
- Make the PM core carry out optimizations for devices with driver PM
flags set in some cases and make a few drivers set those flags
(Rafael Wysocki).
- Fix and clean up wrapper routines allowing runtime PM device
callbacks to be re-used for system-wide PM, change the generic
power domains (genpd) framework to stop using those routines
incorrectly and fix up a driver depending on that behavior of genpd
(Rafael Wysocki, Ulf Hansson, Geert Uytterhoeven).
- Fix and clean up the PM core's device wakeup framework and
re-factor system-wide PM core code related to device wakeup
(Rafael Wysocki, Ulf Hansson, Brian Norris).
- Make more x86-based systems use the Low Power Sleep S0 _DSM
interface by default (to fix power button wakeup from
suspend-to-idle on Surface Pro3) and add a kernel command line
switch to tell it to ignore the system sleep blacklist in the ACPI
core (Rafael Wysocki).
- Fix a race condition related to cpufreq governor module removal and
clean up the governor management code in the cpufreq core (Rafael
Wysocki).
- Drop the unused generic code related to the handling of the static
power energy usage model in the CPU cooling thermal driver along
with the corresponding documentation (Viresh Kumar).
- Add mt2712 support to the Mediatek cpufreq driver (Andrew-sh
Cheng).
- Add a new operating point to the imx6ul and imx6q cpufreq drivers
and switch the latter to using clk_bulk_get() (Anson Huang, Dong
Aisheng).
- Add support for multiple regulators to the TI cpufreq driver along
with a new DT binding related to that and clean up that driver
somewhat (Dave Gerlach).
- Fix a powernv cpufreq driver regression leading to incorrect CPU
frequency reporting, fix that driver to deal with non-continguous
P-states correctly and clean it up (Gautham Shenoy, Shilpasri
Bhat).
- Add support for frequency scaling on Armada 37xx SoCs through the
generic DT cpufreq driver (Gregory CLEMENT).
- Fix error code paths in the mvebu cpufreq driver (Gregory CLEMENT).
- Fix a transition delay setting regression in the longhaul cpufreq
driver (Viresh Kumar).
- Add Skylake X (server) support to the intel_pstate cpufreq driver
and clean up that driver somewhat (Srinivas Pandruvada).
- Clean up the cpufreq statistics collection code (Viresh Kumar).
- Drop cluster terminology and dependency on physical_package_id from
the PSCI driver and drop dependency on arm_big_little from the SCPI
cpufreq driver (Sudeep Holla).
- Add support for system-wide suspend and resume to the RAPL power
capping driver and drop a redundant semicolon from it (Zhen Han,
Luis de Bethencourt).
- Make SPI domain validation (in the SCSI SPI transport driver) and
system-wide suspend mutually exclusive as they rely on the same
underlying mechanism and cannot be carried out at the same time
(Bart Van Assche).
- Fix the computation of the amount of memory to preallocate in the
hibernation core and clean up one function in there (Rainer Fiebig,
Kyungsik Lee).
- Prepare the Operating Performance Points (OPP) framework for being
used with power domains and clean up one function in it (Viresh
Kumar, Wei Yongjun).
- Clean up the generic sysfs interface for device PM (Andy
Shevchenko).
- Fix several minor issues in power management frameworks and clean
them up a bit (Arvind Yadav, Bjorn Andersson, Geert Uytterhoeven,
Gustavo Silva, Julia Lawall, Luis de Bethencourt, Paul Gortmaker,
Sergey Senozhatsky, gaurav jindal).
- Make it easier to disable PM via Kconfig (Mark Brown).
- Clean up the cpupower and intel_pstate_tracer utilities (Doug
Smythies, Laura Abbott)"
* tag 'pm-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (89 commits)
PCI / PM: Remove spurious semicolon
cpufreq: scpi: remove arm_big_little dependency
drivers: psci: remove cluster terminology and dependency on physical_package_id
powercap: intel_rapl: Fix trailing semicolon
dmaengine: rcar-dmac: Make DMAC reinit during system resume explicit
PM / runtime: Allow no callbacks in pm_runtime_force_suspend|resume()
PM / hibernate: Drop unused parameter of enough_swap
PM / runtime: Check ignore_children in pm_runtime_need_not_resume()
PM / runtime: Rework pm_runtime_force_suspend/resume()
PM / genpd: Stop/start devices without pm_runtime_force_suspend/resume()
cpufreq: powernv: Dont assume distinct pstate values for nominal and pmin
cpufreq: intel_pstate: Add Skylake servers support
cpufreq: intel_pstate: Replace bxt_funcs with core_funcs
platform/x86: surfacepro3: Support for wakeup from suspend-to-idle
ACPI / PM: Use Low Power S0 Idle on more systems
PM / wakeup: Print warn if device gets enabled as wakeup source during sleep
PM / domains: Don't skip driver's ->suspend|resume_noirq() callbacks
PM / core: Propagate wakeup_path status flag in __device_suspend_late()
PM / core: Re-structure code for clearing the direct_complete flag
powercap: add suspend and resume mechanism for SOC power limit
...
|
|
en_rx_am.c was deleted in 'net-next' but had a bug fixed in it in
'net'.
The esp{4,6}_offload.c conflicts were overlapping changes.
The 'out' label is removed so we just return ERR_PTR(-EINVAL)
directly.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 3515832cc614 ("scsi: qla2xxx: Reset the logo flag, after target
re-login.")fixed the target re-login after session relogin is complete,
but missed out the qlt_free_session_done() path.
This patch clears send_els_logo flag in qlt_free_session_done()
callback.
[mkp: checkpatch]
Fixes: 3515832cc614 ("scsi: qla2xxx: Reset the logo flag, after target re-login.")
Signed-off-by: Himanshu Madhani <hmadhani@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The arcmsr uses its own implementation of time_to_tm(), along with
do_gettimeofday() to read the current time. While the algorithm used
here is fine in principle, it suffers from two problems:
- it assigns the seconds portion of the timeval to a 32-bit unsigned
integer that overflows in 2106 even on 64-bit architectures.
- do_gettimeofday() returns a time_t that overflows in 2038 on all
32-bit systems.
This changes the time retrieval function to ktime_get_real_seconds(),
which returns a proper 64-bit value, and replaces the open-coded
time_to_tm() algorithm with a call to the safe time64_to_tm().
I checked way all numbers are indexed and found that months are given in
range 0..11 while the days are in range 1..31, same as 'struct tm', but
the year value that the firmware expects starts in 2000 while 'struct
tm' is based on year 1900, so it needs a small adjustment.
[mkp: checkpatch tweaks]
Fixes: b416c099472a ("scsi: arcmsr: Add a function to set date and time to firmware")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We get stuck in the loop when firmware sends a cqe response during
connection recovery.
Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
While testing with the ARM specific memset() macro removed, I ran into a
compiler warning that shows an old bug:
drivers/scsi/arm/fas216.c: In function 'fas216_rq_sns_done':
drivers/scsi/arm/fas216.c:2014:40: error: argument to 'sizeof' in 'memset' call is the same expression as the destination; did you mean to provide an explicit length? [-Werror=sizeof-pointer-memaccess]
It turns out that the definition of the scsi_cmd structure changed back
in linux-2.6.25, so now we clear only four bytes (sizeof(pointer))
instead of 96 (SCSI_SENSE_BUFFERSIZE). I did not check whether we
actually need to initialize the buffer here, but it's clear that if we
do it, we should use the correct size.
Fixes: de25deb18016 ("[SCSI] use dynamically allocated sense buffer")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Trivial fix removes unneeded semicolons after switch blocks.
This issue was detected by using the Coccinelle software.
Signed-off-by: Christopher Díaz Riveros <chrisadr@gentoo.org>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When device gone, NULL pointer can be accessed in free_device callback
if during SAS controller reset as we clear structure sas_dev prior.
Actually we can only set dev_type as SAS_PHY_UNUSED and not clear
structure sas_dev as all the members of structure sas_dev will be
re-initialized after device found.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch implements LED feature of directly attached disk for v2 hw.
As libsas has provided an interface lldd_write_gpio() for this feature,
we just need realise the interface following SPGIO API.
We use an CPLD to finish the hardware part of this feature, and the base
address of CPLD should be configured through ACPI or DT tables.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
NVMe passthrough via MFI interface. Current MegaRAID product supports
different types of encapsulation via the MFI framework.
NVMe native command should be framed by application and it should be
embedded in MFI as payload. The driver will provide interface to send
the MFI frame along with the payload (in this case, payload is NVMe
native command) to the firmware. Driver already has an existing, similar
interface for SATA and SMP passthrough.
1. Driver will pass MFI command to the firmware if the latter supports
NVMe encapsulated processing (not all SAS3.5 firmware supports this
feature).
2. Driver exposes sysfs entry support_nvme_encapsulation. This is
required for backward compatibility for applications using earlier
driver versions that did not process IOCTL frames and could result in
host hang.
This is already fixed as part of commit 82add4e1b354 ("scsi:
megaraid_sas: Incorrect processing of IOCTL frames for SMP/STP
commands")
[mkp: clarified commit message]
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
do_gettimeofday() overflows in 2038 on 32-bit architectures and is
deprecated, so convert this driver to call ktime_get_real()
directly. This also simplifies the calculation.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
struct timespec is deprecated since it overflows in 2038 on 32-bit
architectures, so we should use timespec64 consistently.
I'm slightly adapting the format strings here, to make sure we print the
nanoseconds with the correct number of leading zeroes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix to return error code -ENOMEM from the error handling case instead of
0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Replace "" with NULL for product revision level, and merge TEXEL
duplicate entries.
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Cc: SCSI ML <linux-scsi@vger.kernel.org>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Anil Gurumurthy <anil.gurumurthy@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
[mkp: sparse warning]
Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"One fix for SAS attached SATA CD-ROMs. It turns out that the libata
handling of CD devices relies on the SCSI error handler, so disable
async aborts (which don't start the error handler) for these devices"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: libsas: Disable asynchronous aborts for SATA devices
|
|
This patch fixes following smatch warning:
drivers/scsi/qla2xxx/qla_init.c:1054 __qla24xx_handle_gpdb_event() warn: inconsistent indenting
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch fixes following smatch warning:
drivers/scsi/qla2xxx/qla_iocb.c:2622 qla2x00_els_dcmd2_sp_done() error: '%pC' expects argument of type 'struct clk*', argument 8 has type 'uchar[]'
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch fixes following Smatch warning:
drivers/scsi/qla2xxx/qla_init.c:130 qla2x00_async_iocb_timeout() error: we previously assumed 'fcport' could be null (see line 107)
Fixes: 5c25d451163c ("scsi: qla2xxx: Fix NULL pointer access for fcport structure")
Reported by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
During error test case where switch port status is toggled from enable to
disable, following stack trace is seen which indicates recursion trying to
send terminate exchange. This regression was introduced by commit
82de802ad46e ("scsi: qla2xxx: Preparation for Target MQ.")
BUG: stack guard page was hit at ffffb96488383ff8 (stack is ffffb96488384000..ffffb96488387fff)
BUG: stack guard page was hit at ffffb964886c3ff8 (stack is ffffb964886c4000..ffffb964886c7fff)
kernel stack overflow (double-fault): 0000 [#1] SMP
qlt_term_ctio_exchange+0x9c/0xb0 [qla2xxx]
qlt_term_ctio_exchange+0x9c/0xb0 [qla2xxx]
qlt_term_ctio_exchange+0x9c/0xb0 [qla2xxx]
qlt_term_ctio_exchange+0x9c/0xb0 [qla2xxx]
qlt_term_ctio_exchange+0x9c/0xb0 [qla2xxx]
Fixes: 82de802ad46e ("scsi: qla2xxx: Preparation for Target MQ.")
Cc: <stable@vger.kernel.org> #4.10
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch fixes regression added by commit d74595278f4ab
("scsi: qla2xxx: Add multiple queue pair functionality.").
When driver is not able to get reqeusted IRQs from the system, driver will
attempt tp clean up memory before failing hardware probe. During this cleanup,
driver assigns NULL value to the pointer which has not been allocated by
driver yet. This results in a NULL pointer access.
Log file will show following message and stack trace
qla2xxx [0000:a3:00.1]-00c7:21: MSI-X: Failed to enable support, giving up -- 32/-1.
qla2xxx [0000:a3:00.1]-0037:21: Falling back-to MSI mode --1.
qla2xxx [0000:a3:00.1]-003a:21: Failed to reserve interrupt 821 already in use.
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffffc010c4b6>] qla2x00_probe_one+0x18b6/0x2730 [qla2xxx]
PGD 0
Oops: 0002 [#1] SMP
Fixes: d74595278f4ab ("scsi: qla2xxx: Add multiple queue pair functionality.").
Cc: <stable@vger.kernel.org> # 4.10
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We should set the error code if fc_remote_port_add() fails.
Cc: <stable@vger.kernel.org> #v4.12+
Fixes: daf0cd445a21 ("scsi: storvsc: Add support for FC rport.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Cathy Avery <cavery@redhat.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The function _get_st_from_smid is local to the source and does not need
to be in global scope, so make it static.
Cleans up sparse warning:
symbol '_get_st_from_smid' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fixes the following sparse warning:
drivers/scsi/hisi_sas/hisi_sas_main.c:1691:25: warning:
symbol 'host_attrs' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Introduce a state enum into sdebug_defer objects to indicate which, if
any, defer method has been used with the associated command. Also add 2
bools to indicate which of the defer methods has been initialized. Those
objects are re-used but the initialization only needs to be done
once. This simplifies command cancellation handling.
Now the delay associated with a deferred response of a command cannot be
changed (once started) by changing the delay (and ndelay) parameters in
sysfs. Command aborts and driver shutdown are still honoured immediately
when received.
[mkp: applied by hand]
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This saves a little .text and gets rid of the unmotivated line break and
the sizeof(...) style inconsistency.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
SCSI sense buffers, stored in struct scsi_cmnd.sense and therefore
contained in the scsi_sense_cache slab cache, need to be copied to/from
userspace.
cache object allocation:
drivers/scsi/scsi_lib.c:
scsi_select_sense_cache(...):
return ... ? scsi_sense_isadma_cache : scsi_sense_cache
scsi_alloc_sense_buffer(...):
return kmem_cache_alloc_node(scsi_select_sense_cache(), ...);
scsi_init_request(...):
...
cmd->sense_buffer = scsi_alloc_sense_buffer(...);
...
cmd->req.sense = cmd->sense_buffer
example usage trace:
block/scsi_ioctl.c:
(inline from sg_io)
blk_complete_sghdr_rq(...):
struct scsi_request *req = scsi_req(rq);
...
copy_to_user(..., req->sense, len)
scsi_cmd_ioctl(...):
sg_io(...);
In support of usercopy hardening, this patch defines a region in
the scsi_sense_cache slab cache in which userspace copy operations
are allowed.
This region is known as the slab cache's usercopy region. Slab caches
can now check that each dynamically sized copy operation involving
cache-managed memory falls entirely within the slab's usercopy region.
Signed-off-by: David Windsor <dave@nullcore.net>
[kees: adjust commit log, provide usage trace]
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
No functional changes.
This patch is a re-work of DCMD refire code to better manage all the
different cases to decide whether to REFIRE or SKIP or COMPLETE certain
DCMD.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Expose FW outstanding commands (fw_outstanding) through sysfs interface.
This helps in debugging certain performance issues in the field.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Performance improvement:
Current driver calls stream detection unconditionally for all IOs.
Stream Detection logic is not required for most of the fast path IO. To
improve performance, avoid stream detection logic and do it only if
required.
Below are the cases where stream detection is required in driver:
1. All non-FastPath IOs (IOs going to FW)
2. Fast Path reads sent to ReadAhead capable VDs.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Issue – There may be some IO accessing incorrect raid map, but driver
has checks in IO path to handle those cases. It is always better to move
to new raid map only once raid map is populated and validated. No
functional defect. Fix is provided as part of review. Fix – Update
instance->map_id after driver has populated new driver raid map from
firmware raid map.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
controller state in IOCTL path
In IOCTL path, re-use megasas_wait_for_adapter_operational API to detect
controller state. This will make driver to use this API uniformly in all
cases where we need to wait for adapter to become operational.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Driver needs to avoid PCI writes while OCR is in progress. Use
reset_mutex to synchronize between firing DCMDs MR_DCMD_PD_GET_INFO and
MR_DCMD_DRV_GET_TARGET_PROP while OCR is triggered. Without this fix,
if Device/VD add/creation is in progress and at the same time MR
Firmware is going through OCR, user may see OCR never completed and it
may need system reboot. This scenario is rare to occur. Fix is provided
as part of review.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Issue - Driver returns DID_NO_CONNECT when unload is in progress,
indicated using instance->unload flag. In case of dynamic unload of
driver, this flag is set before calling scsi_remove_host(). While doing
manual driver unload, user will see lots of prints for Sync Cache
command with DID_NO_CONNECT status.
Fix - Set the instance->unload flag after scsi_remove_host(). Allow
device removal process to be completed and do not block any command
before that. SCSI commands (like SYNC_CACHE) are received (as part of
scsi_remove_host) by driver during unload will be submitted further down
to the drives.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
in RAID map
Currently driver does not validate ldcount provided by firmware. If the
value is invalid, fail RAID map validation accordingly. This issue is
rare to hit in field and is fixed as part of code review.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In megasas_get_seq_num, the status of the DCMD fired to FW is not
returned, it always returns success. We could end up registering AEN
request with incorrect sequence number if the DCMD failed. Return the
DCMD status back to caller. This was discovered during code review and
very rare to see issue in field to see AEN request failed bt FW.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit b9637d14dc00 ("scsi: megaraid_sas: Resize MFA frame used for IOC
INIT to 4k") increased the size of IOC INIT frame to 4k. Need to use
updated size when memsetting init_frame.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
