| Age | Commit message (Collapse) | Author |
|---|
|
The init/exit() of the driver only calls platform_driver_{un}register(),
so it can be simpilfied by using module_platform_driver().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If of_parse_phandle_with_args() called from __thermal_of_bind() or
__thermal_of_unbind() fails, cooling_spec.np will not be initialized,
so move the of_node_put() calls below the respective return value checks
to avoid dereferencing an uninitialized pointer.
Fixes: 3fd6d6e2b4e8 ("thermal/of: Rework the thermal device tree initialization")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Check if BPMP supports thermal trip points, and if not,
do not expose the .set_trips callback to the thermal core
framework. This can happen in virtualized environments
where asynchronous communication with VM BPMP drivers is not
available.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20221129153914.2699041-1-cyndis@kapsi.fi
|
|
This reworks the ACPI thermal driver to use a table of generic trip
point structures on top of the internal representation of trip points
and removes thermal zone callbacks that are not necessary any more
from it.
It requires some relatively small changes to be made in the thermal core
too and it is based on top of changes reworking ACPI device notification
handling that are included in this merge.
* acpi-thermal: (24 commits)
ACPI: thermal: Eliminate code duplication from acpi_thermal_notify()
ACPI: thermal: Drop unnecessary thermal zone callbacks
ACPI: thermal: Rework thermal_get_trend()
ACPI: thermal: Use trip point table to register thermal zones
thermal: core: Rework and rename __for_each_thermal_trip()
ACPI: thermal: Introduce struct acpi_thermal_trip
ACPI: thermal: Carry out trip point updates under zone lock
ACPI: thermal: Clean up acpi_thermal_register_thermal_zone()
thermal: core: Add priv pointer to struct thermal_trip
thermal: core: Introduce thermal_zone_device_exec()
thermal: core: Do not handle trip points with invalid temperature
ACPI: thermal: Drop redundant local variable from acpi_thermal_resume()
ACPI: thermal: Do not attach private data to ACPI handles
ACPI: thermal: Drop enabled flag from struct acpi_thermal_active
ACPI: thermal: Drop nocrt parameter
ACPI: thermal: Install Notify() handler directly
ACPI: NFIT: Remove unnecessary .remove callback
ACPI: NFIT: Install Notify() handler directly
ACPI: HED: Install Notify() handler directly
ACPI: battery: Install Notify() handler directly
...
|
|
These fix a few issues in the Intel DTS IOSF thermal driver, clean up
code in it and make it use trip point tables for registering thermal
zones.
* thermal-intel:
thermal: intel: intel_soc_dts_iosf: Use struct thermal_trip
thermal: intel: intel_soc_dts_iosf: Rework critical trip setup
thermal: intel: intel_soc_dts_iosf: Add helper for resetting trip points
thermal: intel: intel_soc_dts_iosf: Change initialization ordering
thermal: intel: intel_soc_dts_iosf: Pass sensors to update_trip_temp()
thermal: intel: intel_soc_dts_iosf: Untangle update_trip_temp()
thermal: intel: intel_soc_dts_iosf: Always assume notification support
thermal: intel: intel_soc_dts_iosf: Drop redundant symbol definition
thermal: intel: intel_soc_dts_iosf: Always use 2 trips
|
|
Rework the currently unused __for_each_thermal_trip() to pass original
pointers to struct thermal_trip objects to the callback, so it can be
used for updating trip data (e.g. temperatures), rename it to
for_each_thermal_trip() and make it available to modular drivers.
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Introduce a new helper function, thermal_zone_device_exec(), that can
be used by drivers to run a given callback routine under the zone lock.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch adds the support for Loongson-2 thermal sensor controller,
which can support maximum four sensor selectors that corresponding to four
sets of thermal control registers and one set of sampling register. The
sensor selector can selector a speific thermal sensor as temperature input.
The sampling register is used to obtain the temperature in real time, the
control register GATE field is used to set the threshold of high or low
temperature, when the input temperature is higher than the high temperature
threshold or lower than the low temperature threshold, an interrupt will
occur.
Signed-off-by: zhanghongchen <zhanghongchen@loongson.cn>
Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230817021007.10350-1-zhuyinbo@loongson.cn
|
|
Use IS_ERR_OR_NULL() to detect an error pointer or a null pointer
open-coding to simplify the code.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230817014900.3094512-1-lizetao1@huawei.com
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230814180921.3336-1-aboutphysycs@gmail.com
|
|
platform_set_drvdata()
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230811191548.3340-1-aboutphysycs@gmail.com
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230811192847.3838-1-aboutphysycs@gmail.com
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230811194032.4240-1-aboutphysycs@gmail.com
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230809154813.16033-1-aboutphysycs@gmail.com
|
|
Currently, when a controller is configured to use filtered mode, thermal
readings are valid only about 30% of the time.
Upon testing, it was noticed that lowering any of the interval settings
resulted in an improved rate of valid data. The same was observed when
decreasing the number of samples for each sensor (which also results in
quicker measurements).
Retrying the read with a timeout longer than the time it takes to
resample (about 344us with these settings and 4 sensors) also improves
the rate.
Lower all timing settings to the minimum, configure the filtering to
single sample, and poll the measurement register for at least one period
to improve the data validity on filtered mode. With these changes in
place, out of 100000 reads, a single one failed, ie 99.999% of the data
was valid.
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230713154743.611870-1-nfraprado@collabora.com
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230810112344.3806-1-aboutphysycs@gmail.com
|
|
platform_set_drvdata()
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230810112015.3578-1-aboutphysycs@gmail.com
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230810111330.3248-1-aboutphysycs@gmail.com
|
|
'soc' is an enum, thus cast of pointer on 64-bit compile test with W=1
causes:
exynos_tmu.c:890:14: error: cast to smaller integer type 'enum soc_type' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230810091318.70261-1-krzysztof.kozlowski@linaro.org
|
|
The driver depends on CONFIG_OF, it is not necessary to use
of_match_ptr() here.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230809101439.2663042-1-ruanjinjie@huawei.com
|
|
Referring to platform_get_irq()'s definition, the return value has
already been checked if ret < 0, and printed via dev_err_probe().
Calling dev_err_probe() one more time outside platform_get_irq()
is obviously redundant.
Removing dev_err_probe() outside platform_get_irq() to clean up
above problem.
Signed-off-by: Chen Jiahao <chenjiahao16@huawei.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230802094527.988842-1-chenjiahao16@huawei.com
|
|
The sun8i thermal driver reads calibration data via the nvmem API at
startup, updating the device configuration and not referencing the data
again. Rather than explicitly freeing the nvmem data the driver relies
on devm_ to release it, even though the data is never referenced again.
The allocation is still tracked so it's not leaked but this is notable
when looking at the code and is a little wasteful so let's instead
explicitly free the nvmem after we're done with it.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230719-thermal-sun8i-free-nvmem-v1-1-f553d5afef79@kernel.org
|
|
It's redundant, let's remove it.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230626125515.18830-1-frank.li@vivo.com
|
|
This patch fixes the following sparse warnings:
drivers/thermal/qcom/tsens-v1.c:24:40: sparse: warning: symbol 'tsens_qcs404_nvmem' was not declared. Should it be static?
drivers/thermal/qcom/tsens-v0_1.c:26:40: sparse: warning: symbol 'tsens_8916_nvmem' was not declared. Should it be static?
drivers/thermal/qcom/tsens-v0_1.c:42:40: sparse: warning: symbol 'tsens_8974_nvmem' was not declared. Should it be static?
drivers/thermal/qcom/tsens-v0_1.c:64:40: sparse: warning: symbol 'tsens_8974_backup_nvmem' was not declared. Should it be static?
No functional change intended.
Signed-off-by: Min-Hua Chen <minhuadotchen@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230713160415.149381-1-minhuadotchen@gmail.com
|
|
nvmem_cell_read_u32() may return -EPROBE_DEFER if NVMEM supplier has not
yet been probed. Future reprobe may succeed, so printing:
i.mx8mm_thermal 30260000.tmu: Failed to read OCOTP nvmem cell (-517).
to the log is confusing. Fix this by using dev_err_probe. This also
elevates the message from warning to error, which is more correct: The
log message is only ever printed in probe error path and probe aborts
afterwards, so it really warrants an error-level message.
Fixes: 403291648823 ("thermal/drivers/imx: Add support for loading calibration data from OCOTP")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230708112647.2897294-1-a.fatoum@pengutronix.de
|
|
The documentation says "If an error occurs, ERR_PTR(-ERROR) will be
returned" but the current code checks against a NULL pointer returned.
Fix this by checking if IS_ERR().
Signed-off-by: Minjie Du <duminjie@vivo.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230713042413.2519-1-duminjie@vivo.com
|
|
Each LVTS thermal controller can have up to four sensors, each capable
of triggering its own interrupt when its measured temperature crosses
the configured threshold. The threshold for each sensor is handled
separately by the thermal framework, since each one is registered with
its own thermal zone and trips. However, the temperature thresholds are
configured on the controller, and therefore are shared between all
sensors on that controller.
When the temperature measured by the sensors is different enough to
cause the thermal framework to configure different thresholds for each
one, interrupts start triggering on sensors outside the last threshold
configured.
To address the issue, track the thresholds required by each sensor and
only actually set the highest one in the hardware, and disable
interrupts for all sensors outside the current configured range.
Fixes: f5f633b18234 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230706153823.201943-7-nfraprado@collabora.com
|
|
The thermal framework might leave the low threshold unset if there
aren't any lower trip points. This leaves the register zeroed, which
translates to a very high temperature for the low threshold. The
interrupt for this threshold is then immediately triggered, and the
state machine gets stuck, preventing any other temperature monitoring
interrupts to ever trigger.
(The same happens by not setting the Cold or Hot to Normal thresholds
when using those)
Set the unused threshold to a valid low value. This value was chosen so
that for any valid golden temperature read from the efuse, when the
value is converted to raw and back again to milliCelsius, the result
doesn't underflow.
Fixes: f5f633b18234 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230706153823.201943-6-nfraprado@collabora.com
|
|
Out of the many interrupts supported by the hardware, the only ones of
interest to the driver currently are:
* The temperature went over the high offset threshold, for any of the
sensors
* The temperature went below the low offset threshold, for any of the
sensors
* The temperature went over the stage3 threshold
These are the only thresholds configured by the driver through the
OFFSETH, OFFSETL, and PROTTC registers, respectively.
The current interrupt mask in LVTS_MONINT_CONF, enables many more
interrupts, including data ready on sensors for both filtered and
immediate mode. These are not only not handled by the driver, but they
are also triggered too often, causing unneeded overhead. Disable these
unnecessary interrupts.
The meaning of each bit can be seen in the comment describing
LVTS_MONINTST in the IRQ handler.
Fixes: f5f633b18234 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230706153823.201943-5-nfraprado@collabora.com
|
|
There are two kinds of temperature monitoring interrupts available:
* High Offset, Low Offset
* Hot, Hot to normal, Cold
The code currently uses the hot/h2n/cold interrupts, however in a way
that doesn't work: the cold threshold is left uninitialized, which
prevents the other thresholds from ever triggering, and the h2n
interrupt is used as the lower threshold, which prevents the hot
interrupt from triggering again after the thresholds are updated by the
thermal framework, since a hot interrupt can only trigger again after
the hot to normal interrupt has been triggered.
But better yet than addressing those issues, is to use the high/low
offset interrupts instead. This way only two thresholds need to be
managed, which have a simpler state machine, making them a better match
to the thermal framework's high and low thresholds.
Fixes: f5f633b18234 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230706153823.201943-4-nfraprado@collabora.com
|
|
Each controller can be configured to operate on immediate or filtered
mode. On filtered mode, the sensors are enabled by setting the
corresponding bits in MONCTL0, while on immediate mode, by setting
MSRCTL1.
Previously, the code would set MSRCTL1 for all four sensors when
configured to immediate mode, but given that the controller might not
have all four sensors connected, this would cause interrupts to trigger
for non-existent sensors. Fix this by handling the MSRCTL1 register
analogously to the MONCTL0: only enable the sensors that were declared.
Fixes: f5f633b18234 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230706153823.201943-3-nfraprado@collabora.com
|
|
There is a single IRQ handler for each LVTS thermal domain, and it is
supposed to check each of its underlying controllers for the origin of
the interrupt and clear its status. However due to a typo, only the
first controller was ever being handled, which resulted in the interrupt
never being cleared when it happened on the other controllers. Add the
missing index so interrupts are handled for all controllers.
Fixes: f5f633b18234 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230706153823.201943-2-nfraprado@collabora.com
|
|
Because the number of trip points in each thermal zone and their
types are known to intel_soc_dts_iosf_init() prior to the registration
of the thermal zones, make it create an array of struct thermal_trip
entries in each struct intel_soc_dts_sensor_entry object and make
add_dts_thermal_zone() use thermal_zone_device_register_with_trips()
for thermal zone registration and pass that array as its second
argument.
Drop the sys_get_trip_temp() and sys_get_trip_type() callback
functions along with the respective callback pointers in
tzone_ops, because they are not necessary any more.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
Critical trip points appear in the DTS thermal zones only after those
thermal zones have been registered via intel_soc_dts_iosf_init().
Moreover, they are "created" by changing the type of an existing trip
point from THERMAL_TRIP_PASSIVE to THERMAL_TRIP_CRITICAL via
intel_soc_dts_iosf_add_read_only_critical_trip(), the caller of which
has to be careful enough to pass at least 1 as the number of read-only
trip points to intel_soc_dts_iosf_init() beforehand.
This is questionable, because user space may have started to use the
trips at the time when intel_soc_dts_iosf_add_read_only_critical_trip()
runs and there is no synchronization between it and sys_set_trip_temp().
To address it, use the observation that nonzero number of read-only
trip points is only passed to intel_soc_dts_iosf_init() when critical
trip points are going to be used, so in fact that function may get all
of the information regarding the critical trip points upfront and it
can configure them before registering the corresponding thermal zones.
Accordingly, replace the read_only_trip_count argument of
intel_soc_dts_iosf_init() with a pair of new arguments related to
critical trip points: a bool one indicating whether or not critical
trip points are to be used at all and an int one representing the
critical trip point temperature offset relative to Tj_max. Use these
arguments to configure the critical trip points before the registration
of the thermal zones and to compute the number of writeable trip points
in add_dts_thermal_zone().
Modify both callers of intel_soc_dts_iosf_init() to take these changes
into account and drop the intel_soc_dts_iosf_add_read_only_critical_trip()
call, that is not necessary any more, from intel_soc_thermal_init(),
which also allows it to return success right after requesting the IRQ.
Finally, drop intel_soc_dts_iosf_add_read_only_critical_trip()
altogether, because it does not have any more users.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
Because trip points are reset for each sensor in two places in the
same way, add a helper function for that to reduce code duplication
a bit.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
The initial configuration of trip points in intel_soc_dts_iosf_init()
takes place after registering the sensor thermal zones which is
potentially problematic, because it may race with the setting of trip
point temperatures via sysfs, as there is no synchronization between it
and sys_set_trip_temp().
To address this, change the initialization ordering so that the trip
points are configured prior to the registration of thermal zones.
Accordingly, change the cleanup ordering in intel_soc_dts_iosf_exit()
to remove the thermal zones before resetting the trip points.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
After previous changes, update_trip_temp() only uses its dts argument to
get to the sensors field in the struct intel_soc_dts_sensor_entry object
pointed to by that argument, so pass the value of that field directly to
it instead.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
Function update_trip_temp() is currently used for the initialization
of trip points as well as for changing trip point temperatures in
sys_set_trip_temp().
This is quite confusing and passing the value of dts->trip_types[trip]
to it so that it can store that value in the same memory location is
not particularly useful, because it only is necessary to set the
trip point type once, at the initialization time.
For this reason, drop the last argument from update_trip_temp() and
introduce configure_trip() calling the former internally for the
initial configuration of trip points.
Modify the majority of update_trip_temp() callers to use
configure_trip() instead of it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
None of the existing callers of intel_soc_dts_iosf_init() passes
INTEL_SOC_DTS_INTERRUPT_NONE as the first argument to it, so the
notification local variable in it is always true and the
notification_support argument of add_dts_thermal_zone() is always
true either.
For this reason, drop the notification local variable from
intel_soc_dts_iosf_init() and the notification_support argument from
add_dts_thermal_zone() and rearrange the latter to always set
writable_trip_cnt and trip_mask.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
SOC_MAX_DTS_SENSORS is already defined in intel_soc_dts_iosf.h which is
included in intel_soc_dts_iosf.c, so it does not need to be defined in
the latter again.
Drop the redundant definition of that symbol from intel_soc_dts_iosf.c.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
Both the existing callers of intel_soc_dts_iosf_init() pass 2 as the trip
count argument, so it can be replaced with SOC_MAX_DTS_TRIPS everywhere in
the code and the trip_count argument of that function can be dropped.
This also allows the trip_count field to be dropped from struct
intel_soc_dts_sensor_entry, as it is always equal to 2, and some
related code can be simplified.
Make changes accordingly.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
Trip points with temperature set to THERMAL_TEMP_INVALID are as good as
disabled, so make handle_thermal_trip() ignore them.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Alderlake N is an E-core only product using Gracemont
micro-architecture. It fits the pre-existing naming scheme perfectly
fine, adhere to it.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230807150405.686834933@infradead.org
|
|
Depends on the interface used, the RAPL registers can be either MSR
indexes or memory mapped IO addresses. Current RAPL common code uses u64
to save both MSR and memory mapped IO registers. With this, when
handling register address with an __iomem annotation, it triggers a
sparse warning like below:
sparse warnings: (new ones prefixed by >>)
>> drivers/powercap/intel_rapl_tpmi.c:141:41: sparse: sparse: incorrect type in initializer (different address spaces) @@ expected unsigned long long [usertype] *tpmi_rapl_regs @@ got void [noderef] __iomem * @@
drivers/powercap/intel_rapl_tpmi.c:141:41: sparse: expected unsigned long long [usertype] *tpmi_rapl_regs
drivers/powercap/intel_rapl_tpmi.c:141:41: sparse: got void [noderef] __iomem *
Fix the problem by using a union to save the registers instead.
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202307031405.dy3druuy-lkp@intel.com/
Tested-by: Wang Wendy <wendy.wang@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
Since commit 3d439b1a2ad3 ("thermal/core: Alloc-copy-free the thermal
zone parameters structure"), thermal_zone_device_register() allocates
a copy of the tzp argument and frees it when unregistering, so
thermal_of_zone_register() now ends up leaking its original tzp and
double-freeing the tzp copy. Fix this by locating tzp on stack instead.
Fixes: 3d439b1a2ad3 ("thermal/core: Alloc-copy-free the thermal zone parameters structure")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: 6.4+ <stable@vger.kernel.org> # 6.4+: 8bcbb18c61d6: thermal: core: constify params in thermal_zone_device_register
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Since commit 3d439b1a2ad3 ("thermal/core: Alloc-copy-free the thermal zone
parameters structure"), thermal_zone_device_register() allocates a copy
of the tzp argument and callers need not explicitly manage its lifetime.
This means the function no longer cares about the parameter being
mutable, so constify it.
No functional change.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The driver is accessing the thermal zone state to ensure the state is
different from the one we want to set.
We don't want the driver to access the thermal zone device internals.
Actually, the thermal core code already checks if the thermal zone's
state is different before calling this function, thus this check is
duplicate.
Remove it.
Acked-by: srinivas pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Use the thermal core API to access the thermal zone "type" field
instead of directly using the structure field. While here, remove
access to the temperature field, as this driver is reporting fake
temperature, which can be replaced with INT3400_FAKE_TEMP. Also
replace hardcoded 20C with INT3400_FAKE_TEMP
Acked-by: srinivas pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
