| Age | Commit message (Collapse) | Author |
|---|
|
Add support for the RX2 receiver which is used as the third receiver in
asymmetric links. This requires expanding the results array for the
additional third data word of the hardware margining results.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Make the result parsing and formatting code less repetitive in
preparation for adding another result for Gen 4 asymmetric link support.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Replace the raw values and macros with an enum and use it consistently.
No functional changes.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
With USB4 Gen 4, the link can be configured into an asymmetric mode,
where there are three receivers and only one transmitter. The USB4
specification also uses the "all lanes" nomenclature instead of "both
lanes".
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Add a debugfs knob for USB4 Gen 4 margining eye selection. Gen 4 uses
3-level pulse amplitude modulation (PAM3) which changes how margining
measurements are made because PAM3 has two eyes per lane from which
the margins can be measured.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Parse the Gen 4 specific capabilities. Change the return types of
independent_voltage_margins() and independent_time_margins() to enums
that distinguish between the Gen 2/3 and Gen 4 margins since they behave
differently between generations.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
USB4 specification defines the metadata needed to perform software
margining, as well as the necessary steps which include waiting for
dwell time.
- Add dwell_time attribute to set the wait time while performing
margining and checking for link errors.
- Add error_counter attribute to configure error counter prior to
margining test.
- Add voltage_time_offset attribute to set the voltage or time offset
steps before performing the software margining test.
- Perform software margining test for dwell duration, break if there are
link errors, stop the clocks and provide results.
Below is a minimalistic example how this can be used. Note these values
are just examples. The exact values in practice depend on host specific
capabilities and the type of measurement to be performed.
# cd /sys/kernel/debug/thunderbolt/ROUTER/portX/margining/
# echo software > mode
# echo 400 > dwell_time
# echo 1 > run
As usual the results attribute contains the results of a succesfull run.
Signed-off-by: R Kannappan <r.kannappan@intel.com>
Co-developed-by: Rene Sapiens <rene.sapiens@intel.com>
Signed-off-by: Rene Sapiens <rene.sapiens@intel.com>
Co-developed-by: Aapo Vienamo <aapo.vienamo@linux.intel.com>
Signed-off-by: Aapo Vienamo <aapo.vienamo@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Add optional extended voltage offset range support for software and
hardware margining as defined by the USB4 specification.
If supported, it can be enabled like below:
# cd /sys/kernel/debug/thunderbolt/ROUTER/portX/margining/
# echo Y > optional_voltage_offset
Signed-off-by: Rene Sapiens <rene.sapiens@intel.com>
Co-developed-by: R Kannappan <r.kannappan@intel.com>
Signed-off-by: R Kannappan <r.kannappan@intel.com>
Co-developed-by: Aapo Vienamo <aapo.vienamo@linux.intel.com>
Signed-off-by: Aapo Vienamo <aapo.vienamo@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Consolidate the hardware and software margining parameters into a single
structure to reduce the number of parameters passed to the margining
functions.
Signed-off-by: Rene Sapiens <rene.sapiens@intel.com>
Co-developed-by: Aapo Vienamo <aapo.vienamo@linux.intel.com>
Signed-off-by: Aapo Vienamo <aapo.vienamo@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Use the FIELD_GET() macro instead of open coding the masks and shifts.
This makes the code more compact and improves readability as it avoids
the need to wrap excessively long lines.
Signed-off-by: Aapo Vienamo <aapo.vienamo@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Retimers support lane margining as well so make this available through
debugfs in the same way as we do for the USB4 ports. When this is
enabled we also expose retimers on the other side of the cable because
typically margining is implemented only on direction towards the cable.
However, for the retimers on the other side of the cable we do not allow
NVM upgrade to avoid confusing the existing userspace (the same retimer
may now appear twice with different name) and is probably not a good
idea anyway.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
This makes it possible to read and write USB4 port and retimer sideband
registers through debugfs which is useful for debugging and manufacturing
purposes. We add "sb_regs" debugfs attribute under each USB4 port and
retimer that is used to access the sideband.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
According to USB4 retimer specification, the process of firmware update
sequence requires issuing a SET_INBOUND_SBTX port operation that later
shall be followed by UNSET_INBOUND_SBTX port operation. This last step
is not currently issued by the driver but it is necessary to make sure
the retimers are put back to passthrough mode even during enumeration.
If this step is missing the link may not come up properly after
soft-reboot for example.
For this reason issue UNSET_INBOUND_SBTX after SET_INBOUND_SBTX for
enumeration and also when the NVM upgrade is run.
Reported-by: Christian Schaubschläger <christian.schaubschlaeger@gmx.at>
Link: https://lore.kernel.org/linux-usb/b556f5ed-5ee8-9990-9910-afd60db93310@gmx.at/
Cc: stable@vger.kernel.org
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
USB4 spec defines standard set of registers to be used for receiver lane
margining. This is useful for I/O interface quality and electrical
robustness validation during manufacturing. Expose receiver lane
margining through new debugfs directory "margining" that is added under
each connected USB4 port. Users can then run the margining by writing to
the exposed attributes under that directory.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
When accessing retimers when there is no cable connected we are going to
need additional USB4 port operations. First the port needs to be put
into offline mode, and then the sideband channel transactions must be
enabled on the SBTX line. This adds support for these operations.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
USB4 spec specifies standard access to retimers (both on-board and
cable) through USB4 port sideband access. This makes it possible to
upgrade their firmware in the same way than we already do with the
routers.
This enumerates on-board retimers under each USB4 port when the link
comes up and adds them to the bus under the router the retimer belongs
to. Retimers are exposed in sysfs with name like <device>:<port>.<index>
where device is the router the retimer belongs to, port is the USB4 port
the retimer is connected to and index is the retimer index under that
port (starting from 1). This applies to the upstream USB4 port as well
so if there is on-board retimer between the port and the router it is
also added accordingly.
At this time we do not add cable retimers but there is no techincal
restriction to do so in the future if needed. It is not clear whether it
makes sense to upgrade their firmwares and at least Thunderbolt 3 cables
it has not been done outside of lab environments.
The sysfs interface is made to follow the router NVM upgrade to make it
easy to extend the existing userspace (fwupd) to handle these as well.
Signed-off-by: Kranthi Kuntala <kranthi.kuntala@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
USB4 spec specifies standard set of sideband operations that are send
over the low speed link to access either retimers on the link or the
link parter (the other router). The USB4 retimer spec extends these and
adds operations for retimer NVM upgrade.
This implements the retimer access and NVM upgrade USB4 port sideband
operations which we need for retimer support in the patch that follows.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
