summaryrefslogtreecommitdiff
path: root/drivers/thunderbolt/tb_msgs.h
AgeCommit message (Collapse)Author
2019-12-18thunderbolt: Populate PG field in hot plug acknowledgment packetMika Westerberg
USB4 1.0 section 6.4.2.7 specifies a new field (PG) in notification packet that is sent as response of hot plug/unplug events. This field tells whether the acknowledgment is for plug or unplug event. This needs to be set accordingly in order the router to send further hot plug notifications. To make it simpler we fill the field unconditionally. Legacy devices do not look at this field so there should be no problems with them. While there rename tb_cfg_error() to tb_cfg_ack_plug() and update the log message accordingly. The function is only used to ack plug/unplug events. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Link: https://lore.kernel.org/r/20191217123345.31850-4-mika.westerberg@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-02thunderbolt: Add support for lane bondingMika Westerberg
Lane bonding allows aggregating two 10/20 Gb/s (depending on the generation) lanes into a single 20/40 Gb/s bonded link. This allows sharing the full bandwidth more efficiently. In order to establish lane bonding we need to check that lane bonding is possible through link controller and that both ends of the link actually supports 2x widths. This also means that all the paths should be established through the primary port so update tb_path_alloc() to handle this as well. Lane bonding is supported starting from Falcon Ridge (2nd generation) controllers. We also expose the current speed and number of lanes under each device except the host router following similar attribute naming than USB bus. Expose speed and number of lanes for both directions to allow possibility of asymmetric link in the future. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-08-26thunderbolt: Add support for Intel Ice LakeMika Westerberg
The Thunderbolt controller is integrated into the Ice Lake CPU itself and requires special flows to power it on and off using force power bit in NHI VSEC registers. Runtime PM (RTD3) and Sx flows also differ from the discrete solutions. Now the firmware notifies the driver whether RTD3 entry or exit are possible. The driver is responsible of sending Go2Sx command through link controller mailbox when system enters Sx states (suspend-to-mem/disk). Rest of the ICM firwmare flows follow Titan Ridge. Signed-off-by: Raanan Avargil <raanan.avargil@intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com> Tested-by: Mario Limonciello <mario.limonciello@dell.com>
2019-04-18thunderbolt: Add XDomain UUID exchange supportMika Westerberg
Currently ICM has been handling XDomain UUID exchange so there was no need to have it in the driver yet. However, since now we are going to add the same capabilities to the software connection manager it needs to be handled properly. For this reason modify the driver XDomain protocol handling so that if the remote domain UUID is not filled in the core will query it first and only then start the normal property exchange flow. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2018-10-02thunderbolt: Convert rest of the driver files to use SPDX identifierMika Westerberg
This gets rid of the licence boilerplate duplicated in each file. While there fix doubled space in domain.c author line. No functional changes intended. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-25thunderbolt: Add support for runtime PMMika Westerberg
When Thunderbolt host controller is set to RTD3 mode (Runtime D3) it is present all the time. Because of this it is important to runtime suspend the controller whenever possible. In case of ICM we have following rules which all needs to be true before the host controller can be put to D3: - The controller firmware reports to support RTD3 - All the connected devices announce support for RTD3 - There is no active XDomain connection Implement this using standard Linux runtime PM APIs so that when all the children devices are runtime suspended, the Thunderbolt host controller PCI device is runtime suspended as well. The ICM firmware then starts powering down power domains towards RTD3 but it can prevent this if it detects that there is an active Display Port stream (this is not visible to the software, though). The Thunderbolt host controller will be runtime resumed either when there is a remote wake event (device is connected or disconnected), or when there is access from userspace that requires hardware access. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-09thunderbolt: Add support for Intel Titan RidgeRadion Mirchevsky
Intel Titan Ridge is the next Thunderbolt 3 controller. The ICM firmware message format in Titan Ridge differs from Falcon Ridge and Alpine Ridge somewhat because it is using route strings addressing devices. In addition to that the DMA port of 4-channel (two port) controller is in different port number than the previous controllers. There are some other minor differences as well. This patch add support for Intel Titan Ridge and the new ICM firmware message format. Signed-off-by: Radion Mirchevsky <radion.mirchevsky@intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2018-03-09thunderbolt: Add support for preboot ACLMika Westerberg
Preboot ACL is a mechanism that allows connecting Thunderbolt devices boot time in more secure way than the legacy Thunderbolt boot support. As with the legacy boot option, this also needs to be enabled from the BIOS before booting is allowed. Difference to the legacy mode is that the userspace software explicitly adds device UUIDs by sending a special message to the ICM firmware. Only the devices listed in the boot ACL are connected automatically during the boot. This works in both "user" and "secure" security levels. We implement this in Linux by exposing a new sysfs attribute (boot_acl) below each Thunderbolt domain. The userspace software can then update the full list as needed. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
2018-03-09thunderbolt: Add 'boot' attribute for devicesYehezkel Bernat
In various cases, Thunderbolt device can be connected by ICM on boot without waiting for approval from user. Most cases are related to OEM-specific BIOS configurations. This information is interesting for user-space as if the device isn't in SW ACL, it may create a friction in the user experience where the device is automatically authorized if it's connected on boot but requires an explicit user action if connected after OS is up. User-space can use this information to suggest adding the device to SW ACL for auto-authorization on later connections. Signed-off-by: Yehezkel Bernat <yehezkel.bernat@intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
2018-03-09thunderbolt: Move driver ready handling to struct icmMika Westerberg
Intel Titan Ridge uses slightly different format for ICM driver ready response, so add a new ->driver_ready() callback to struct icm and move the existing handling to a separate function which we then use in Falcon Ridge and Alpine Ridge. No functional changes intended. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
2018-03-09thunderbolt: Handle rejected Thunderbolt devicesMika Westerberg
The ICM firmware rejects devices if the maximum topology limit is exceeded (more than 6 devices are connected). If that happens just log a message to the kernel message buffer and bail out. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
2017-10-02thunderbolt: Add support for XDomain discovery protocolMika Westerberg
When two hosts are connected over a Thunderbolt cable, there is a protocol they can use to communicate capabilities supported by the host. The discovery protocol uses automatically configured control channel (ring 0) and is build on top of request/response transactions using special XDomain primitives provided by the Thunderbolt base protocol. The capabilities consists of a root directory block of basic properties used for identification of the host, and then there can be zero or more directories each describing a Thunderbolt service and its capabilities. Once both sides have discovered what is supported the two hosts can setup high-speed DMA paths and transfer data to the other side using whatever protocol was agreed based on the properties. The software protocol used to communicate which DMA paths to enable is service specific. This patch adds support for the XDomain discovery protocol to the Thunderbolt bus. We model each remote host connection as a Linux XDomain device. For each Thunderbolt service found supported on the XDomain device, we create Linux Thunderbolt service device which Thunderbolt service drivers can then bind to based on the protocol identification information retrieved from the property directory describing the service. This code is based on the work done by Amir Levy and Michael Jamet. Signed-off-by: Michael Jamet <michael.jamet@intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-02thunderbolt: Move enum tb_cfg_pkg_type to thunderbolt.hMika Westerberg
These will be needed by Thunderbolt services when sending and receiving XDomain control messages. While there change TB_CFG_PKG_PREPARE_TO_SLEEP value to be decimal in order to be consistent with other members. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Michael Jamet <michael.jamet@intel.com> Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-02thunderbolt: Remove __packed from ICM message structuresMika Westerberg
These messages are all 32-bit aligned and they should be packed without the __packed attribute just fine. It also allows compiler to generate better code on some architectures. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Michael Jamet <michael.jamet@intel.com> Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-07-24thunderbolt: use uuid_t instead of uuid_beChristoph Hellwig
Switch thunderbolt to the new uuid type. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Amir Goldstein <amir73il@gmail.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2017-06-09thunderbolt: Add support for Internal Connection Manager (ICM)Mika Westerberg
Starting from Intel Falcon Ridge the internal connection manager running on the Thunderbolt host controller has been supporting 4 security levels. One reason for this is to prevent DMA attacks and only allow connecting devices the user trusts. The internal connection manager (ICM) is the preferred way of connecting Thunderbolt devices over software only implementation typically used on Macs. The driver communicates with ICM using special Thunderbolt ring 0 (control channel) messages. In order to handle these messages we add support for the ICM messages to the control channel. The security levels are as follows: none - No security, all tunnels are created automatically user - User needs to approve the device before tunnels are created secure - User need to approve the device before tunnels are created. The device is sent a challenge on future connects to be able to verify it is actually the approved device. dponly - Only Display Port and USB tunnels can be created and those are created automatically. The security levels are typically configurable from the system BIOS and by default it is set to "user" on many systems. In this patch each Thunderbolt device will have either one or two new sysfs attributes: authorized and key. The latter appears for devices that support secure connect. In order to identify the device the user can read identication information, including UUID and name of the device from sysfs and based on that make a decision to authorize the device. The device is authorized by simply writing 1 to the "authorized" sysfs attribute. This is following the USB bus device authorization mechanism. The secure connect requires an additional challenge step (writing 2 to the "authorized" attribute) in future connects when the key has already been stored to the NVM of the device. Non-ICM systems (before Alpine Ridge) continue to use the existing functionality and the security level is set to none. For systems with Alpine Ridge, even on Apple hardware, we will use ICM. This code is based on the work done by Amir Levy and Michael Jamet. Signed-off-by: Michael Jamet <michael.jamet@intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Andreas Noever <andreas.noever@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-06-09thunderbolt: Move control channel messages to tb_msgs.hMika Westerberg
We will be forwarding notifications received from the control channel to the connection manager implementations. This way they can decide what to do if anything when a notification is received. To be able to use control channel messages from other files, move them to tb_msgs.h. No functional changes intended. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com> Reviewed-by: Michael Jamet <michael.jamet@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Andreas Noever <andreas.noever@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>