| Age | Commit message (Collapse) | Author |
|---|
|
Add CSIZE sanitization for unsupported CSIZE configurations. In
addition, if parity is asked for but CSx was unsupported, the sensible
result is CS8+parity which requires setting USART_CR1_M0 like with 9
bits.
Incorrect CSIZE results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Fixes: c8a9d043947b (serial: stm32: fix word length configuration)
Cc: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220519081808.3776-9-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In case the RS485 mode is emulated using GPIO RTS, use the TC interrupt
to deassert the GPIO RTS, otherwise the GPIO RTS stays asserted after a
transmission ended and the RS485 cannot work.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Erwan Le Ray <erwan.leray@foss.st.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jean Philippe Romain <jean-philippe.romain@foss.st.com>
Cc: Valentin Caron <valentin.caron@foss.st.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-serial@vger.kernel.org
Link: https://lore.kernel.org/r/20220430162845.244655-2-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull out the GPIO RTS enable and disable handling into separate function.
Limit the scope of GPIO RTS toggling only to GPIO emulated RS485 too.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Erwan Le Ray <erwan.leray@foss.st.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jean Philippe Romain <jean-philippe.romain@foss.st.com>
Cc: Valentin Caron <valentin.caron@foss.st.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-serial@vger.kernel.org
Link: https://lore.kernel.org/r/20220430162845.244655-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add early console support in stm32 uart driver.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220419085330.1178925-4-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for KGDB in stm32 serial driver by implementing characters
polling callbacks (poll_init, poll_get_char and poll_put_char).
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Jean Philippe Romain <jean-philippe.romain@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220419085330.1178925-3-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rework stm32_usart_console_putchar() function in order to anticipate
the case where the character can never be sent.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220419085330.1178925-2-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In uart_set_rs485_config() the serial core already ensures that only one of
both options RTS on send or RTS after send is set. It also assigns the
passed serial_rs485 struct to the uart port.
So remove the check and the assignment from the drivers rs485_config()
function to avoid redundancy.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20220410104642.32195-4-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, uart_console_write->putchar's second parameter (the
character) is of type int. It makes little sense, provided uart_console_write()
accepts the input string as "const char *s" and passes its content -- the
characters -- to putchar(). So switch the character's type to unsigned
char.
We don't use char as that is signed on some platforms. That would cause
troubles for drivers which (implicitly) cast the char to u16 when
writing to the device. Sign extension would happen in that case and the
value written would be completely different to the provided char. DZ is
an example of such a driver -- on MIPS, it uses u16 for dz_out in
dz_console_putchar().
Note we do the char -> uchar conversion implicitly in
uart_console_write(). Provided we do not change size of the data type,
sign extension does not happen there, so the problem is void.
This makes the types consistent and unified with the rest of the uart
layer, which uses unsigned char in most places already. One exception is
xmit_buf, but that is going to be converted later.
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@kernel.org>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: "Maciej W. Rozycki" <macro@orcam.me.uk>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Karol Gugala <kgugala@antmicro.com>
Cc: Mateusz Holenko <mholenko@antmicro.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Taichi Sugaya <sugaya.taichi@socionext.com>
Cc: Takao Orito <orito.takao@socionext.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: Orson Zhai <orsonzhai@gmail.com>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Chunyan Zhang <zhang.lyra@gmail.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <peter@korsgaard.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com> [atmel_serial]
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Neil Armstrong <narmstrong@baylibre.com> # meson_serial
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220303080831.21783-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Enable mctrl_gpio wake_irq if device_may_wakeup when usart is suspended,
and disable mctrl_gpios wake_irq if device_may_wakeup when usart is
resumed.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20220203171644.12231-3-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
x_char is ignored by stm32_usart_start_tx() when xmit buffer is empty.
Fix start_tx condition to allow x_char to be sent.
Fixes: 48a6092fb41f ("serial: stm32-usart: Add STM32 USART Driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220111164441.6178-3-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When sending x_char in stm32_usart_transmit_chars(), driver can overwrite
the value of TDR register by the value of x_char. If this happens, the
previous value that was present in TDR register will not be sent through
uart.
This code checks if the previous value in TDR register is sent before
writing the x_char value into register.
Fixes: 48a6092fb41f ("serial: stm32-usart: Add STM32 USART Driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220111164441.6178-2-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In this error handling, "transmit_chars_dma" function will call
"transmit_chars_pio" once per characters. But "transmit_chars_pio" will
continue to send characters while xmit buffer is not empty.
Remove this useless loop, one call is sufficient.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220104182445.4195-5-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If flow control is enabled, framework will call stop_tx to
pause transfer and then call start_tx to resume transfer.
Clear USART_CR3_DMAT bit in stop_tx ops to pause DMA transfer.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220104182445.4195-4-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
TX DMA state condition is handled by tx_dma_busy boolean.
This boolean is set when dma descriptor is requested and reset when dma
channel is stopped (dma_terminate).
In stm32_usart_serial_remove(), stm32_usart_stop_tx() and
stm32_usart_transmit_chars_dma() fallback error case, DMA channel is
stopped but tx_dma_busy is not handled.
Rework the driver by using two new functions to solve this issue:
- stm32_usart_tx_dma_started return true if DMA TX have a descriptor.
- stm32_usart_tx_dma_enabled return true if DMAT bit is set.
stm32_usart_tx_dma_started uses tx_dma_busy flag to prevent dual DMA
transaction at the same time. This flag is set when a DMA transaction
begins and is unset when dmaengine_terminate_async function is called.
A new DMA transaction cannot be created if this flag is set.
Create a new function "stm32_usart_tx_dma_terminate" to be sure the flag
is unset after each call of dmaengine_terminate_async.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220104182445.4195-3-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Terminate DMA transaction and clear CR3_DMAT when shutdown is requested,
instead of when remove is requested. If DMA transfer is not stopped in
shutdown ops, driver will fail to start a new DMA transfer after next
startup ops.
Fixes: 3489187204eb ("serial: stm32: adding dma support")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220104182445.4195-2-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Data may be stored in DMA RX buffer, when suspending. The data needs
to be pushed to the upper layer. We can't rely on the timeout IRQ (RTOR)
that can't be triggered into low power state. So safely clear DMA request
(DMAR), force the DMA reception routines to push RX buffer content, before
disabling RX DMA. This way, handover to pio mode is safe.
Only call tty_flip_buffer_push() when there is RX data to handle.
Move the locking outside of stm32_usart_receive_chars() to prevent a race
condition, when disabling DMA request upon suspend / pm_runtime_suspend.
Data may be received under IRQ and pushed before
stm32_usart_receive_chars() has pushed older data from DMA rx_buf upon
suspend.
The sequence in suspend routine needs proper locking to avoid this.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20211025134229.8456-4-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
DMA prevents the system to suspend when an UART RX wake-up source is
using DMA. DMA can't suspend while DMA channels are still active.
Terminate DMA transfer at suspend, and restart a new DMA transfer at
resume. Create stm32_usart_start_rx_dma_cyclic function to factorize
dma RX initialization. Move RX DMA code related to wakeup into
stm32_usart_serial_en_wakeup() routine to ease further improvements
on wakeup from low power modes.
Don't enable/disable wakeup on uninitialized port.
There may be data residue in the RX FIFO while suspending. Flush it at
suspend time. Receiver timeout interrupt won't trigger later in low power
mode, so call stm32_usart_receive_chars() in case there's data to handle.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20211025134229.8456-3-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The RX DMA channel is kept active forever (from the probe). That prevents
going to low power mode when it is used. This change moves the
DMA configuration and enabling procedures to startup routine to allow
transition to low power mode.
The DMA disabling procedure is implemented in stop_rx routine as this
ops has to stop characters reception, and DMA transation in shutdown.
Clean useless dma_async_tx_descriptor initialization to NULL value.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20211025134229.8456-2-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Disable DMA request line (if enabled) to switch in PIO mode in throttle
ops, so the RX data gets queues into the FIFO. The hardware flow control
is triggered when the RX FIFO is full.
Switch back to DMA mode (re-enable DMA request line) in unthrottle ops.
Hardware flow control is stopped when FIFO is not full anymore.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20211020150332.10214-4-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch reworks RX support over DMA to improve reliability:
- change dma buffer cyclic configuration by using 2 periods. DMA buffer
data are handled by a flip-flop between the 2 periods in order to avoid
risk of data loss/corruption
- change the size of dma buffer to 4096 to limit overruns
- add rx errors management (breaks, parity, framing and overrun).
When an error occurs on the uart line, the dma request line is masked at
HW level. The SW must 1st clear DMAR (dma request line enable), to
handle the error, then re-enable DMAR to recover. So, any correct data
is taken from the DMA buffer, before handling the error itself. Then
errors are handled from RDR/ISR/FIFO (e.g. in PIO mode). Last, DMA
reception is resumed.
- add a condition on DMA request line in DMA RX routines in order to
switch to PIO mode when no DMA request line is disabled, even if the DMA
channel is still enabled.
When the UART is wakeup source and is configured to use DMA for RX, any
incoming data that wakes up the system isn't correctly received.
At data reception, the irq_handler handles the WUF irq, and then the
data reception over DMA.
As the DMA transfer has been terminated at suspend, and will be restored
by resume callback (which has no yet been called by system), the data
can't be received.
The wake-up data has to be handled in PIO mode while suspend callback
has not been called.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20211020150332.10214-3-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Re-introduce an irq flag condition in usart_receive_chars.
This condition has been deleted by commit 75f4e830fa9c ("serial: do not
restore interrupt state in sysrq helper").
This code was present to handle threaded case, and has been removed
because it is no more needed in this case. Nevertheless an irq safe lock
is still needed in some cases, when DMA should be stopped to receive errors
or breaks in PIO mode.
This patch is a precursor to the complete rework or stm32 serial driver
DMA implementation.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20211020150332.10214-2-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use devm_platform_get_and_ioremap_resource() to simplify code.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20210814131418.13608-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the defined variable 'dev' to make the code cleaner.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20210814124951.30084-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the function stm32_usart_init_port, intent of the code maybe when
irq returns a value of zero, the return should be '-ENODEV'. But the
conditional expression '? :' maybe clerical error, it should be
'?:' to make '-ENODEV' work.
But in fact, as the example in platform.c is
* int irq = platform_get_irq(pdev, 0);
* if (irq < 0)
* return irq;
So the return value of zero is unnecessary to check, at last remove
the unnecessary '?: -ENODEV'.
Co-developed-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20210811105136.25392-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the previous patch, we introduced tty_get_char_size() and
tty_get_frame_size() for computing character and frame sizes,
respectively. Here, we make use of them in various tty drivers where
applicable.
The stats look nice: 12 insertions, 169 deletions.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Oliver Neukum <oneukum@suse.com>
Acked-by: Alex Elder <elder@kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210610090247.2593-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Defer device probe operation when a DMA channel request probe deferral.
With this change both DMA channels are acquired before DMA channels are
configured. Once no probe deferral is expected, DMAs are
configured and any failure in their configuration will make the driver
to fallback to interrupt mode as prior this change.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Link: https://lore.kernel.org/r/20210610100020.2318-1-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There's no need to initialise irq-flags variables before saving the
interrupt state.
Drop the redundant initialisations from drivers that got this wrong.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210519092541.10137-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add the support for two optional DT properties, to configure RX and TX
FIFO thresholds:
- rx-threshold
- tx-threshold
This replaces hard-coded 8 bytes threshold. Keep 8 as the default value if
not specified, for backward compatibility.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Changes in v2:
Change added properties naming as proposed by Rob Herring.
Link: https://lore.kernel.org/r/20210413174015.23011-5-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the uart_unlock_and_check_sysrq() helper to defer sysrq processing
until receive processing is done and the port lock has been released.
This allows cleaning up the console_write() implementation by not having
to work around the recursive sysrq case (by dropping locking completely)
and also makes the console code work with PREEMPT_RT by no longer
relying on local_irq_save().
Reviewed-by: Valentin Caron<valentin.caron@foss.st.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210416140557.25177-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When DMA is enabled the receive handler runs in a threaded handler, but
the primary handler up until very recently neither disabled interrupts
in the device or used IRQF_ONESHOT. This would lead to a deadlock if an
interrupt comes in while the threaded receive handler is running under
the port lock.
Commit ad7676812437 ("serial: stm32: fix a deadlock condition with
wakeup event") claimed to fix an unrelated deadlock, but unfortunately
also disabled interrupts in the threaded handler. While this prevents
the deadlock mentioned in the previous paragraph it also defeats the
purpose of using a threaded handler in the first place.
Fix this by making the interrupt one-shot and not disabling interrupts
in the threaded handler.
Note that (receive) DMA must not be used for a console port as the
threaded handler could be interrupted while holding the port lock,
something which could lead to a deadlock in case an interrupt handler
ends up calling printk.
Fixes: ad7676812437 ("serial: stm32: fix a deadlock condition with wakeup event")
Fixes: 3489187204eb ("serial: stm32: adding dma support")
Cc: stable@vger.kernel.org # 4.9
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Cc: Gerald Baeza <gerald.baeza@st.com>
Reviewed-by: Valentin Caron<valentin.caron@foss.st.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210416140557.25177-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
STM32 F7/H7 usarts supports RX & TX pin swapping.
Add option to turn it on.
Tested on STM32MP157.
Acked-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Martin Devera <devik@eaxlabs.cz>
Link: https://lore.kernel.org/r/20210328154306.22674-2-devik@eaxlabs.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The wakeup specific IRQ management is no more needed to wake up the stm32
plaform. A relationship has been established between the EXTI and
the EVENT IRQ, just need to declare the EXTI interrupt instead of the
UART event IRQ.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210319184253.5841-5-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove useless call to stm32_usart_serial_en_wakeup() routine in suspend
callback. When called with "false" argument, this routine is clearing UESM
and WUFIE bits if usart is not wakeup source. Those bits are already
cleared in set_termios(), and then in serial_resume() callback when usart
is wakeup source.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210319184253.5841-3-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rework wakeup management by activating uart as wakeup source when usart
device OR its tty virtual device parent is wakeup source.
This patch aim to avoid potential misalignment between serial and tty
wakeup flags.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210319184253.5841-2-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add the support for "flush_buffer" ops in order to flush any write buffers,
reset any DMA state and stop any ongoing DMA transfers when the
port->state->xmit circular buffer is cleared.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-14-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In "tx_empty", we should poll TC bit in both DMA and PIO modes (instead of
TXE) to check transmission data register has been transmitted independently
of the FIFO mode. TC indicates that both transmit register and shift
register are empty. When shift register is empty, tx_empty should return
TIOCSER_TEMT instead of TC value.
Cleans the USART_CR_TC TCCF register define (transmission complete clear
flag) as it is duplicate of USART_ICR_TCCF.
Fixes: 48a6092fb41f ("serial: stm32-usart: Add STM32 USART Driver")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-13-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Transmission complete error is sent when ISR_TC is not set. If port closure
is requested despite data in TDR / TX FIFO has not been sent (because of
flow control), ISR_TC is not set and error message is sent on port closure
but also when a new port is opened.
Flush the data when port is closed, so the error isn't printed twice upon
next port opening.
Fixes: 64c32eab6603 ("serial: stm32: Add support of TC bit status check")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-12-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fifo flush set USART_RQR register by calling stm32_usart_set_bits
routine (Read/Modify/Write). USART_RQR register is a write only
register. So, read before write isn't correct / relevant to flush
the FIFOs.
Replace stm32_usart_set_bits call by writel_relaxed.
Fixes: 84872dc448fe ("serial: stm32: add RX and TX FIFO flush")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-11-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
stm32_transmit_chars should be called under lock also in tx DMA callback.
Fixes: 3489187204eb ("serial: stm32: adding dma support")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-10-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch add a proper release of dma channels when completing dma tx.
Fixes: 3489187204eb ("serial: stm32: adding dma support")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-9-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CTS/RTS GPIOs support that has been added recently to STM32 UART driver has
introduced scheduled code in a set_termios part protected by a spin lock.
This generates a potential deadlock scenario:
Chain exists of:
&irq_desc_lock_class --> console_owner --> &port_lock_key
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&port_lock_key);
lock(console_owner);
lock(&port_lock_key);
lock(&irq_desc_lock_class);
*** DEADLOCK ***
4 locks held by stty/766:
Move the scheduled code after the spinlock.
Fixes: 6cf61b9bd7cc ("tty: serial: Add modem control gpio support for STM32 UART")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-8-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes several issue with wake-up handling:
- the WUF irq is handled several times at wake-up
- the USART is disabled / enabled at suspend to set wake-up flag.
It can cause glitches during RX.
This patch fix those issues:
- clear wake-up flag and disable wake-up irq in WUF irq handling
- enable wake-up from low power on start bit detection at port
configuration
- Unmask the wake-up flag irq at suspend and mask it at resume
In addition, pm_wakeup_event handling is moved from receice_chars to WUF
irq handling.
Fixes: 270e5a74fe4c ("serial: stm32: add wakeup mechanism")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-7-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Deadlock issue is seen when enabling CONFIG_PROVE_LOCKING=Y, and uart
console as wakeup source. Deadlock occurs when resuming from low power
mode if system is waked up via usart console.
The deadlock is triggered 100% when also disabling console suspend prior
to go to suspend.
Simplified call stack, deadlock condition:
- stm32_console_write <-- spin_lock already held
- print_circular_bug
- pm_wakeup_dev_event <-- triggers lockdep as seen above
- stm32_receive_chars
- stm32_interrupt <-- wakeup via uart console, takes the lock
So, revisit spin_lock in stm32-usart driver:
- there is no need to hold the lock to access ICR (atomic clear of status
flags)
- only hold the lock inside stm32_receive_chars() routine (no need to
call pm_wakeup_dev_event with lock held)
- keep stm32_transmit_chars() routine called with lock held
Fixes: 48a6092fb41f ("serial: stm32-usart: Add STM32 USART Driver")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-6-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
TX and RX FIFO thresholds may be cleared after suspend/resume, depending
on the low power mode.
Those configurations (done in startup) are not effective for UART console,
as:
- the reference manual indicates that FIFOEN bit can only be written when
the USART is disabled (UE=0)
- a set_termios (where UE is set) is requested firstly for console
enabling, before the startup.
Fixes: 84872dc448fe ("serial: stm32: add RX and TX FIFO flush")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-5-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Incorrect characters are observed on console during boot. This issue occurs
when init/main.c is modifying termios settings to open /dev/console on the
rootfs.
This patch adds a waiting loop in set_termios to wait for TX shift register
empty (and TX FIFO if any) before stopping serial port.
Fixes: 48a6092fb41f ("serial: stm32-usart: Add STM32 USART Driver")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-4-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
RX is configured, but usart is not enabled in startup function.
Kernel documentation specifies that startup should enable the port for
reception.
Fix the startup by enabling usart for reception.
Fixes: 84872dc448fe ("serial: stm32: add RX and TX FIFO flush")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-3-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The probe and remove orders are wrong as the uart_port is registered
before saving device data in the probe, and unregistered after DMA
resource deallocation in the remove. uart_port registering should be
done at the end of probe and unregistering should be done at the begin of
remove to avoid resource allocation issues.
Fix probe and remove orders. This enforce resource allocation occur at
proper time.
Terminate both DMA rx and tx transfers before removing device.
Move pm_runtime after uart_remove_one_port() call in remove() to keep the
probe error path.
Fixes: 3489187204eb ("serial: stm32: adding dma support")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-2-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Sync dtc to upstream version v1.6.0-51-g183df9e9c2b9 and build host
fdtoverlay
- Add kbuild support to build DT overlays (%.dtbo)
- Drop NULLifying match table in of_match_device().
In preparation for this, there are several driver cleanups to use
(of_)?device_get_match_data().
- Drop pointless wrappers from DT struct device API
- Convert USB binding schemas to use graph schema and remove old plain
text graph binding doc
- Convert spi-nor and v3d GPU bindings to DT schema
- Tree wide schema fixes for if/then schemas, array size constraints,
and undocumented compatible strings in examples
- Handle 'no-map' correctly for already reserved memblock regions
* tag 'devicetree-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (35 commits)
driver core: platform: Drop of_device_node_put() wrapper
of: Remove of_dev_{get,put}()
dt-bindings: usb: Change descibe to describe in usbmisc-imx.txt
dt-bindings: can: rcar_canfd: Group tuples in pin control properties
dt-bindings: power: renesas,apmu: Group tuples in cpus properties
dt-bindings: mtd: spi-nor: Convert to DT schema format
dt-bindings: Use portable sort for version cmp
dt-bindings: ethernet-controller: fix fixed-link specification
dt-bindings: irqchip: Add node name to PRUSS INTC
dt-bindings: interconnect: Fix the expected number of cells
dt-bindings: Fix errors in 'if' schemas
dt-bindings: iommu: renesas,ipmmu-vmsa: Make 'power-domains' conditionally required
dt-bindings: Fix undocumented compatible strings in examples
kbuild: Add support to build overlays (%.dtbo)
scripts: dtc: Remove the unused fdtdump.c file
scripts: dtc: Build fdtoverlay tool
scripts/dtc: Update to upstream version v1.6.0-51-g183df9e9c2b9
scripts: dtc: Fetch fdtoverlay.c from external DTC project
dt-bindings: thermal: sun8i: Fix misplaced schema keyword in compatible strings
dt-bindings: iio: dac: Fix AD5686 references
...
|
|
Replace "ret" variable by "irq" variable from platform_get_irq condition
handling in stm32_init_port as suggested by Jiri in "STM32 uart cleanup and
improvement" series review.
This change will prevent port->irq to be unexpectly modified by a potential
change of "ret" value introduced by a new patch.
Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210121142309.6327-1-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This driver casts away the constness of struct stm32_usart_info that is
pointed to by the of match table. Use of_device_get_match_data() instead
of of_match_device() here and push the const throughout the code so that
we don't cast away const. This nicely avoids referencing the match table
when it is undefined with configurations where CONFIG_OF=n and fixes the
const issues.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: <linux-serial@vger.kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210123034428.2841052-4-swboyd@chromium.org
|
