summaryrefslogtreecommitdiff
path: root/drivers/tty
AgeCommit message (Collapse)Author
2019-12-17tty/serial: atmel: fix out of range clock divider handlingDavid Engraf
Use MCK_DIV8 when the clock divider is > 65535. Unfortunately the mode register was already written thus the clock selection is ignored. Fix by doing the baud rate calulation before setting the mode. Fixes: 5bf5635ac170 ("tty/serial: atmel: add fractional baud rate support") Signed-off-by: David Engraf <david.engraf@sysgo.com> Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com> Acked-by: Richard Genoud <richard.genoud@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191216085403.17050-1-david.engraf@sysgo.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17tty: link tty and port before configuring it as consoleSudip Mukherjee
There seems to be a race condition in tty drivers and I could see on many boot cycles a NULL pointer dereference as tty_init_dev() tries to do 'tty->port->itty = tty' even though tty->port is NULL. 'tty->port' will be set by the driver and if the driver has not yet done it before we open the tty device we can get to this situation. By adding some extra debug prints, I noticed that: 6.650130: uart_add_one_port 6.663849: register_console 6.664846: tty_open 6.674391: tty_init_dev 6.675456: tty_port_link_device uart_add_one_port() registers the console, as soon as it registers, the userspace tries to use it and that leads to tty_open() but uart_add_one_port() has not yet done tty_port_link_device() and so tty->port is not yet configured when control reaches tty_init_dev(). Further look into the code and tty_port_link_device() is done by uart_add_one_port(). After registering the console uart_add_one_port() will call tty_port_register_device_attr_serdev() and tty_port_link_device() is called from this. Call add tty_port_link_device() before uart_configure_port() is done and add a check in tty_port_link_device() so that it only links the port if it has not been done yet. Suggested-by: Jiri Slaby <jslaby@suse.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191212131602.29504-1-sudipm.mukherjee@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-12serial: sprd: Add clearing break interrupt operationYonghan Ye
A break interrupt will be generated if the RX line was pulled low, which means some abnomal behaviors occurred of the UART. In this case, we still need to clear this break interrupt status, otherwise it will cause irq storm to crash the whole system. Fixes: b7396a38fb28 ("tty/serial: Add Spreadtrum sc9836-uart driver support") Signed-off-by: Yonghan Ye <yonghan.ye@unisoc.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Baolin Wang <baolin.wang7@gmail.com> Link: https://lore.kernel.org/r/925e51b73099c90158e080b8f5bed9b3b38c4548.1575460601.git.baolin.wang7@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-12tty: serial: msm_serial: Fix lockup for sysrq and oopsLeo Yan
As the commit 677fe555cbfb ("serial: imx: Fix recursive locking bug") has mentioned the uart driver might cause recursive locking between normal printing and the kernel debugging facilities (e.g. sysrq and oops). In the commit it gave out suggestion for fixing recursive locking issue: "The solution is to avoid locking in the sysrq case and trylock in the oops_in_progress case." This patch follows the suggestion (also used the exactly same code with other serial drivers, e.g. amba-pl011.c) to fix the recursive locking issue, this can avoid stuck caused by deadlock and print out log for sysrq and oops. Fixes: 04896a77a97b ("msm_serial: serial driver for MSM7K onboard serial peripheral.") Signed-off-by: Leo Yan <leo.yan@linaro.org> Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com> Link: https://lore.kernel.org/r/20191127141544.4277-2-leo.yan@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-03Merge tag 'tty-5.5-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty/serial updates from Greg KH: "Here is the "big" tty and serial driver patches for 5.5-rc1. It's a bit later in the merge window than normal as I wanted to make sure some last-minute patches applied to it were all sane. They seem to be :) There's a lot of little stuff in here, for the tty core, and for lots of serial drivers: - reverts of uartlite serial driver patches that were wrong - msm-serial driver fixes - serial core updates and fixes - tty core fixes - serial driver dma mapping api changes - lots of other tiny fixes and updates for serial drivers All of these have been in linux-next for a while with no reported issues" * tag 'tty-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (58 commits) Revert "serial/8250: Add support for NI-Serial PXI/PXIe+485 devices" vcs: prevent write access to vcsu devices tty: vt: keyboard: reject invalid keycodes tty: don't crash in tty_init_dev when missing tty_port serial: stm32: fix clearing interrupt error flags tty: Fix Kconfig indentation, continued serial: serial_core: Perform NULL checks for break_ctl ops tty: remove unused argument from tty_open_by_driver() tty: Fix Kconfig indentation {tty: serial, nand: onenand}: samsung: rename to fix build warning serial: ifx6x60: add missed pm_runtime_disable serial: pl011: Fix DMA ->flush_buffer() Revert "serial-uartlite: Move the uart register" Revert "serial-uartlite: Add get serial id if not provided" Revert "serial-uartlite: Do not use static struct uart_driver out of probe()" Revert "serial-uartlite: Add runtime support" Revert "serial-uartlite: Change logic how console_port is setup" Revert "serial-uartlite: Use allocated structure instead of static ones" tty: serial: msm_serial: Use dma_request_chan() directly for channel request tty: serial: tegra: Use dma_request_chan() directly for channel request ...
2019-12-03Merge tag 'pci-v5.5-changes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI updates from Bjorn Helgaas: "Enumeration: - Warn if a host bridge has no NUMA info (Yunsheng Lin) - Add PCI_STD_NUM_BARS for the number of standard BARs (Denis Efremov) Resource management: - Fix boot-time Embedded Controller GPE storm caused by incorrect resource assignment after ACPI Bus Check Notification (Mika Westerberg) - Protect pci_reassign_bridge_resources() against concurrent addition/removal (Benjamin Herrenschmidt) - Fix bridge dma_ranges resource list cleanup (Rob Herring) - Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control the MMIO and prefetchable MMIO window sizes of hotplug bridges independently (Nicholas Johnson) - Fix MMIO/MMIO_PREF window assignment that assigned more space than desired (Nicholas Johnson) - Only enforce bus numbers from bridge EA if the bridge has EA devices downstream (Subbaraya Sundeep) - Consolidate DT "dma-ranges" parsing and convert all host drivers to use shared parsing (Rob Herring) Error reporting: - Restore AER capability after resume (Mayurkumar Patel) - Add PoisonTLPBlocked AER counter (Rajat Jain) - Use for_each_set_bit() to simplify AER code (Andy Shevchenko) - Fix AER kernel-doc (Andy Shevchenko) - Add "pcie_ports=dpc-native" parameter to allow native use of DPC even if platform didn't grant control over AER (Olof Johansson) Hotplug: - Avoid returning prematurely from sysfs requests to enable or disable a PCIe hotplug slot (Lukas Wunner) - Don't disable interrupts twice when suspending hotplug ports (Mika Westerberg) - Fix deadlocks when PCIe ports are hot-removed while suspended (Mika Westerberg) Power management: - Remove unnecessary ASPM locking (Bjorn Helgaas) - Add support for disabling L1 PM Substates (Heiner Kallweit) - Allow re-enabling Clock PM after it has been disabled (Heiner Kallweit) - Add sysfs attributes for controlling ASPM link states (Heiner Kallweit) - Remove CONFIG_PCIEASPM_DEBUG, including "link_state" and "clk_ctl" sysfs files (Heiner Kallweit) - Avoid AMD FCH XHCI USB PME# from D0 defect that prevents wakeup on USB 2.0 or 1.1 connect events (Kai-Heng Feng) - Move power state check out of pci_msi_supported() (Bjorn Helgaas) - Fix incorrect MSI-X masking on resume and revert related nvme quirk for Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan) - Always return devices to D0 when thawing to fix hibernation with drivers like mlx4 that used legacy power management (previously we only did it for drivers with new power management ops) (Dexuan Cui) - Clear PCIe PME Status even for legacy power management (Bjorn Helgaas) - Fix PCI PM documentation errors (Bjorn Helgaas) - Use dev_printk() for more power management messages (Bjorn Helgaas) - Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas) - Convert xen-platform from legacy to generic power management (Bjorn Helgaas) - Removed unused .resume_early() and .suspend_late() legacy power management hooks (Bjorn Helgaas) - Rearrange power management code for clarity (Rafael J. Wysocki) - Decode power states more clearly ("4" or "D4" really refers to "D3cold") (Bjorn Helgaas) - Notice when reading PM Control register returns an error (~0) instead of interpreting it as being in D3hot (Bjorn Helgaas) - Add missing link delays required by the PCIe spec (Mika Westerberg) Virtualization: - Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn Helgaas) - Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code previously didn't recognize that) (Kuppuswamy Sathyanarayanan) - Allow VFs to use PASID (the PF PASID capability is shared by the VFs, but the code previously didn't recognize that) (Kuppuswamy Sathyanarayanan) - Disconnect PF and VF ATS enablement, since ATS in PFs and associated VFs can be enabled independently (Kuppuswamy Sathyanarayanan) - Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan) - Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas) - Consolidate ATS declarations in linux/pci-ats.h (Krzysztof Wilczynski) - Remove unused PRI and PASID stubs (Bjorn Helgaas) - Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID interfaces that are only used by built-in IOMMU drivers (Bjorn Helgaas) - Hide PRI and PASID state restoration functions used only inside the PCI core (Bjorn Helgaas) - Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski) - Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut) - Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George Cherian) - Fix the UPDCR register address in the Intel ACS quirk (Steffen Liebergeld) - Unify ACS quirk implementations (Bjorn Helgaas) Amlogic Meson host bridge driver: - Fix meson PERST# GPIO polarity problem (Remi Pommarel) - Add DT bindings for Amlogic Meson G12A (Neil Armstrong) - Fix meson clock names to match DT bindings (Neil Armstrong) - Add meson support for Amlogic G12A SoC with separate shared PHY (Neil Armstrong) - Add meson extended PCIe PHY functions for Amlogic G12A USB3+PCIe combo PHY (Neil Armstrong) - Add arm64 DT for Amlogic G12A PCIe controller node (Neil Armstrong) - Add commented-out description of VIM3 USB3/PCIe mux in arm64 DT (Neil Armstrong) Broadcom iProc host bridge driver: - Invalidate iProc PAXB address mapping before programming it (Abhishek Shah) - Fix iproc-msi and mvebu __iomem annotations (Ben Dooks) Cadence host bridge driver: - Refactor Cadence PCIe host controller to use as a library for both host and endpoint (Tom Joseph) Freescale Layerscape host bridge driver: - Add layerscape LS1028a support (Xiaowei Bao) Intel VMD host bridge driver: - Add VMD bus 224-255 restriction decode (Jon Derrick) - Add VMD 8086:9A0B device ID (Jon Derrick) - Remove Keith from VMD maintainer list (Keith Busch) Marvell ARMADA 3700 / Aardvark host bridge driver: - Use LTSSM state to build link training flag since Aardvark doesn't implement the Link Training bit (Remi Pommarel) - Delay before training Aardvark link in case PERST# was asserted before the driver probe (Remi Pommarel) - Fix Aardvark issues with Root Control reads and writes (Remi Pommarel) - Don't rely on jiffies in Aardvark config access path since interrupts may be disabled (Remi Pommarel) - Fix Aardvark big-endian support (Grzegorz Jaszczyk) Marvell ARMADA 370 / XP host bridge driver: - Make mvebu_pci_bridge_emul_ops static (Ben Dooks) Microsoft Hyper-V host bridge driver: - Add hibernation support for Hyper-V virtual PCI devices (Dexuan Cui) - Track Hyper-V pci_protocol_version per-hbus, not globally (Dexuan Cui) - Avoid kmemleak false positive on hv hbus buffer (Dexuan Cui) Mobiveil host bridge driver: - Change mobiveil csr_read()/write() function names that conflict with riscv arch functions (Kefeng Wang) NVIDIA Tegra host bridge driver: - Fix Tegra CLKREQ dependency programming (Vidya Sagar) Renesas R-Car host bridge driver: - Remove unnecessary header include from rcar (Andrew Murray) - Tighten register index checking for rcar inbound range programming (Marek Vasut) - Fix rcar inbound range alignment calculation to improve packing of multiple entries (Marek Vasut) - Update rcar MACCTLR setting to match documentation (Yoshihiro Shimoda) - Clear bit 0 of MACCTLR before PCIETCTLR.CFINIT per manual (Yoshihiro Shimoda) - Add Marek Vasut and Yoshihiro Shimoda as R-Car maintainers (Simon Horman) Rockchip host bridge driver: - Make rockchip 0V9 and 1V8 power regulators non-optional (Robin Murphy) Socionext UniPhier host bridge driver: - Set uniphier to host (RC) mode always (Kunihiko Hayashi) Endpoint drivers: - Fix endpoint driver sign extension problem when shifting page number to phys_addr_t (Alan Mikhak) Misc: - Add NumaChip SPDX header (Krzysztof Wilczynski) - Replace EXTRA_CFLAGS with ccflags-y (Krzysztof Wilczynski) - Remove unused includes (Krzysztof Wilczynski) - Removed unused sysfs attribute groups (Ben Dooks) - Remove PTM and ASPM dependencies on PCIEPORTBUS (Bjorn Helgaas) - Add PCIe Link Control 2 register field definitions to replace magic numbers in AMDGPU and Radeon CIK/SI (Bjorn Helgaas) - Fix incorrect Link Control 2 Transmit Margin usage in AMDGPU and Radeon CIK/SI PCIe Gen3 link training (Bjorn Helgaas) - Use pcie_capability_read_word() instead of pci_read_config_word() in AMDGPU and Radeon CIK/SI (Frederick Lawler) - Remove unused pci_irq_get_node() Greg Kroah-Hartman) - Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig (Palmer Dabbelt, Michal Simek) - Read all 64 bits of Switchtec part_event_bitmap (Logan Gunthorpe) - Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn Helgaas) - Fix bridge emulation big-endian support (Grzegorz Jaszczyk) - Fix dwc find_next_bit() usage (Niklas Cassel) - Fix pcitest.c fd leak (Hewenliang) - Fix typos and comments (Bjorn Helgaas) - Fix Kconfig whitespace errors (Krzysztof Kozlowski)" * tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (160 commits) PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist asm-generic: Make msi.h a mandatory include/asm header Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T" PCI/MSI: Fix incorrect MSI-X masking on resume PCI/MSI: Move power state check out of pci_msi_supported() PCI/MSI: Remove unused pci_irq_get_node() PCI: hv: Avoid a kmemleak false positive caused by the hbus buffer PCI: hv: Change pci_protocol_version to per-hbus PCI: hv: Add hibernation support PCI: hv: Reorganize the code in preparation of hibernation MAINTAINERS: Remove Keith from VMD maintainer PCI/ASPM: Remove PCIEASPM_DEBUG Kconfig option and related code PCI/ASPM: Add sysfs attributes for controlling ASPM link states PCI: Fix indentation drm/radeon: Prefer pcie_capability_read_word() drm/radeon: Replace numbers with PCI_EXP_LNKCTL2 definitions drm/radeon: Correct Transmit Margin masks drm/amdgpu: Prefer pcie_capability_read_word() PCI: uniphier: Set mode register to host mode drm/amdgpu: Replace numbers with PCI_EXP_LNKCTL2 definitions ...
2019-12-01Merge tag 'compat-ioctl-5.5' of ↵Linus Torvalds
git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground Pull removal of most of fs/compat_ioctl.c from Arnd Bergmann: "As part of the cleanup of some remaining y2038 issues, I came to fs/compat_ioctl.c, which still has a couple of commands that need support for time64_t. In completely unrelated work, I spent time on cleaning up parts of this file in the past, moving things out into drivers instead. After Al Viro reviewed an earlier version of this series and did a lot more of that cleanup, I decided to try to completely eliminate the rest of it and move it all into drivers. This series incorporates some of Al's work and many patches of my own, but in the end stops short of actually removing the last part, which is the scsi ioctl handlers. I have patches for those as well, but they need more testing or possibly a rewrite" * tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground: (42 commits) scsi: sd: enable compat ioctls for sed-opal pktcdvd: add compat_ioctl handler compat_ioctl: move SG_GET_REQUEST_TABLE handling compat_ioctl: ppp: move simple commands into ppp_generic.c compat_ioctl: handle PPPIOCGIDLE for 64-bit time_t compat_ioctl: move PPPIOCSCOMPRESS to ppp_generic compat_ioctl: unify copy-in of ppp filters tty: handle compat PPP ioctls compat_ioctl: move SIOCOUTQ out of compat_ioctl.c compat_ioctl: handle SIOCOUTQNSD af_unix: add compat_ioctl support compat_ioctl: reimplement SG_IO handling compat_ioctl: move WDIOC handling into wdt drivers fs: compat_ioctl: move FITRIM emulation into file systems gfs2: add compat_ioctl support compat_ioctl: remove unused convert_in_user macro compat_ioctl: remove last RAID handling code compat_ioctl: remove /dev/raw ioctl translation compat_ioctl: remove PCI ioctl translation compat_ioctl: remove joystick ioctl translation ...
2019-11-28Merge branch 'pci/resource'Bjorn Helgaas
- Protect pci_reassign_bridge_resources() against concurrent addition/removal (Benjamin Herrenschmidt) - Fix bridge dma_ranges resource list cleanup (Rob Herring) - Add PCI_STD_NUM_BARS for the number of standard BARs (Denis Efremov) - Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control the MMIO and prefetchable MMIO window sizes of hotplug bridges independently (Nicholas Johnson) - Fix MMIO/MMIO_PREF window assignment that assigned more space than desired (Nicholas Johnson) - Only enforce bus numbers from bridge EA if the bridge has EA devices downstream (Subbaraya Sundeep) * pci/resource: PCI: Do not use bus number zero from EA capability PCI: Avoid double hpmemsize MMIO window assignment PCI: Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters PCI: Add PCI_STD_NUM_BARS for the number of standard BARs PCI: Fix missing bridge dma_ranges resource list cleanup PCI: Protect pci_reassign_bridge_resources() against concurrent addition/removal
2019-11-27Merge tag 'riscv/for-v5.5-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux Pull RISC-V updates from Paul Walmsley: "New features: - SECCOMP support - nommu support - SBI-less system support - M-Mode support - TLB flush optimizations Other improvements: - Pass the complete RISC-V ISA string supported by the CPU cores to userspace, rather than redacting parts of it in the kernel - Add platform DMA IP block data to the HiFive Unleashed board DT file - Add Makefile support for BZ2, LZ4, LZMA, LZO kernel image compression formats, in line with other architectures Cleanups: - Remove unnecessary PTE_PARENT_SIZE macro - Standardize include guard naming across arch/riscv" * tag 'riscv/for-v5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (22 commits) riscv: provide a flat image loader riscv: add nommu support riscv: clear the instruction cache and all registers when booting riscv: read the hart ID from mhartid on boot riscv: provide native clint access for M-mode riscv: dts: add support for PDMA device of HiFive Unleashed Rev A00 riscv: add support for MMIO access to the timer registers riscv: implement remote sfence.i using IPIs riscv: cleanup the default power off implementation riscv: poison SBI calls for M-mode riscv: don't allow selecting SBI based drivers for M-mode RISC-V: Add multiple compression image format. riscv: clean up the macro format in each header file riscv: Use PMD_SIZE to replace PTE_PARENT_SIZE riscv: abstract out CSR names for supervisor vs machine mode riscv: separate MMIO functions into their own header file riscv: enter WFI in default_power_off() if SBI does not shutdown RISC-V: Issue a tlb page flush if possible RISC-V: Issue a local tlbflush if possible. RISC-V: Do not invoke SBI call if cpumask is empty ...
2019-11-27Merge tag 'driver-core-5.5-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core updates from Greg KH: "Here is the "big" set of driver core patches for 5.5-rc1 There's a few minor cleanups and fixes in here, but the majority of the patches in here fall into two buckets: - debugfs api cleanups and fixes - driver core device link support for boot dependancy issues The debugfs api cleanups are working to slowly refactor the debugfs apis so that it is even harder to use incorrectly. That work has been happening for the past few kernel releases and will continue over time, it's a long-term project/goal The driver core device link support missed 5.4 by just a bit, so it's been sitting and baking for many months now. It's from Saravana Kannan to help resolve the problems that DT-based systems have at boot time with dependancy graphs and kernel modules. Turns out that no one has actually tried to build a generic arm64 kernel with loads of modules and have it "just work" for a variety of platforms (like a distro kernel). The big problem turned out to be a lack of dependency information between different areas of DT entries, and the work here resolves that problem and now allows devices to boot properly, and quicker than a monolith kernel. All of these patches have been in linux-next for a long time with no reported issues" * tag 'driver-core-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (68 commits) tracing: Remove unnecessary DEBUG_FS dependency of: property: Add device link support for interrupt-parent, dmas and -gpio(s) debugfs: Fix !DEBUG_FS debugfs_create_automount of: property: Add device link support for "iommu-map" of: property: Fix the semantics of of_is_ancestor_of() i2c: of: Populate fwnode in of_i2c_get_board_info() drivers: base: Fix Kconfig indentation firmware_loader: Fix labels with comma for builtin firmware driver core: Allow device link operations inside sync_state() driver core: platform: Declare ret variable only once cpu-topology: declare parse_acpi_topology in <linux/arch_topology.h> crypto: hisilicon: no need to check return value of debugfs_create functions driver core: platform: use the correct callback type for bus_find_device firmware_class: make firmware caching configurable driver core: Clarify documentation for fwnode_operations.add_links() mailbox: tegra: Fix superfluous IRQ error message net: caif: Fix debugfs on 64-bit platforms mac80211: Use debugfs_create_xul() helper media: c8sectpfe: no need to check return value of debugfs_create functions of: property: Add device link support for iommus, mboxes and io-channels ...
2019-11-27Merge tag 'char-misc-5.5-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc driver updates from Greg KH: "Here is the big set of char/misc and other driver patches for 5.5-rc1 Loads of different things in here, this feels like the catch-all of driver subsystems these days. Full details are in the shortlog, but nothing major overall, just lots of driver updates and additions. All of these have been in linux-next for a while with no reported issues" * tag 'char-misc-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (198 commits) char: Fix Kconfig indentation, continued habanalabs: add more protection of device during reset habanalabs: flush EQ workers in hard reset habanalabs: make the reset code more consistent habanalabs: expose reset counters via existing INFO IOCTL habanalabs: make code more concise habanalabs: use defines for F/W files habanalabs: remove prints on successful device initialization habanalabs: remove unnecessary checks habanalabs: invalidate MMU cache only once habanalabs: skip VA block list update in reset flow habanalabs: optimize MMU unmap habanalabs: prevent read/write from/to the device during hard reset habanalabs: split MMU properties to PCI/DRAM habanalabs: re-factor MMU masks and documentation habanalabs: type specific MMU cache invalidation habanalabs: re-factor memory module code habanalabs: export uapi defines to user-space habanalabs: don't print error when queues are full habanalabs: increase max jobs number to 512 ...
2019-11-27Revert "serial/8250: Add support for NI-Serial PXI/PXIe+485 devices"Je Yen Tam
This reverts commit fdc2de87124f5183a98ea7eced1f76dbdba22951 ("serial/8250: Add support for NI-Serial PXI/PXIe+485 devices"). The commit fdc2de87124f ("serial/8250: Add support for NI-Serial PXI/PXIe+485 devices") introduced a breakage on NI-Serial PXI(e)-RS485 devices, RS-232 variants have no issue. The Linux system can enumerate the NI-Serial PXI(e)-RS485 devices, but it broke the R/W operation on the ports. However, the implementation is working on the NI internal Linux RT kernel but it does not work in the Linux main tree kernel. This is only affecting NI products, specifically the RS-485 variants. Reverting the upstream until a proper implementation that can apply to both NI internal Linux kernel and Linux mainline kernel is figured out. Signed-off-by: Je Yen Tam <je.yen.tam@ni.com> Fixes: fdc2de87124f ("serial/8250: Add support for NI-Serial PXI/PXIe+485 devices") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191127075301.9866-1-je.yen.tam@ni.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-27vcs: prevent write access to vcsu devicesNicolas Pitre
Commit d21b0be246bf ("vt: introduce unicode mode for /dev/vcs") guarded against using devices containing attributes as this is not yet implemented. It however failed to guard against writes to any devices as this is also unimplemented. Reported-by: Or Cohen <orcohen@paloaltonetworks.com> Signed-off-by: Nicolas Pitre <npitre@baylibre.com> Cc: <stable@vger.kernel.org> # v4.19+ Cc: Jiri Slaby <jslaby@suse.com> Fixes: d21b0be246bf ("vt: introduce unicode mode for /dev/vcs") Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.1911051030580.30289@knanqh.ubzr Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-26Merge branch 'locking-core-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull locking updates from Ingo Molnar: "The main changes in this cycle were: - A comprehensive rewrite of the robust/PI futex code's exit handling to fix various exit races. (Thomas Gleixner et al) - Rework the generic REFCOUNT_FULL implementation using atomic_fetch_* operations so that the performance impact of the cmpxchg() loops is mitigated for common refcount operations. With these performance improvements the generic implementation of refcount_t should be good enough for everybody - and this got confirmed by performance testing, so remove ARCH_HAS_REFCOUNT and REFCOUNT_FULL entirely, leaving the generic implementation enabled unconditionally. (Will Deacon) - Other misc changes, fixes, cleanups" * 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits) lkdtm: Remove references to CONFIG_REFCOUNT_FULL locking/refcount: Remove unused 'refcount_error_report()' function locking/refcount: Consolidate implementations of refcount_t locking/refcount: Consolidate REFCOUNT_{MAX,SATURATED} definitions locking/refcount: Move saturation warnings out of line locking/refcount: Improve performance of generic REFCOUNT_FULL code locking/refcount: Move the bulk of the REFCOUNT_FULL implementation into the <linux/refcount.h> header locking/refcount: Remove unused refcount_*_checked() variants locking/refcount: Ensure integer operands are treated as signed locking/refcount: Define constants for saturation and max refcount values futex: Prevent exit livelock futex: Provide distinct return value when owner is exiting futex: Add mutex around futex exit futex: Provide state handling for exec() as well futex: Sanitize exit state handling futex: Mark the begin of futex exit explicitly futex: Set task::futex_state to DEAD right after handling futex exit futex: Split futex_mm_release() for exit/exec exit/exec: Seperate mm_release() futex: Replace PF_EXITPIDONE with a state ...
2019-11-23tty: vt: keyboard: reject invalid keycodesDmitry Torokhov
Do not try to handle keycodes that are too big, otherwise we risk doing out-of-bounds writes: BUG: KASAN: global-out-of-bounds in clear_bit include/asm-generic/bitops-instrumented.h:56 [inline] BUG: KASAN: global-out-of-bounds in kbd_keycode drivers/tty/vt/keyboard.c:1411 [inline] BUG: KASAN: global-out-of-bounds in kbd_event+0xe6b/0x3790 drivers/tty/vt/keyboard.c:1495 Write of size 8 at addr ffffffff89a1b2d8 by task syz-executor108/1722 ... kbd_keycode drivers/tty/vt/keyboard.c:1411 [inline] kbd_event+0xe6b/0x3790 drivers/tty/vt/keyboard.c:1495 input_to_handler+0x3b6/0x4c0 drivers/input/input.c:118 input_pass_values.part.0+0x2e3/0x720 drivers/input/input.c:145 input_pass_values drivers/input/input.c:949 [inline] input_set_keycode+0x290/0x320 drivers/input/input.c:954 evdev_handle_set_keycode_v2+0xc4/0x120 drivers/input/evdev.c:882 evdev_do_ioctl drivers/input/evdev.c:1150 [inline] In this case we were dealing with a fuzzed HID device that declared over 12K buttons, and while HID layer should not be reporting to us such big keycodes, we should also be defensive and reject invalid data ourselves as well. Reported-by: syzbot+19340dff067c2d3835c0@syzkaller.appspotmail.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191122204220.GA129459@dtor-ws Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-22tty: don't crash in tty_init_dev when missing tty_portJiri Slaby
We currently warn the user when tty->port is not set in tty_init_dev yet. The warning says that the kernel will crash later. And it really will only few lines below at: tty->port->itty = tty; So be nice and avoid the crash -- return an error instead. And update the warning. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Link: https://lore.kernel.org/r/20191122101721.7222-1-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-21serial: stm32: fix clearing interrupt error flagsFabrice Gasnier
The interrupt clear flag register is a "write 1 to clear" register. So, only writing ones allows to clear flags: - Replace buggy stm32_clr_bits() by a simple write to clear error flags - Replace useless read/modify/write stm32_set_bits() routine by a simple write to clear TC (transfer complete) flag. Fixes: 4f01d833fdcd ("serial: stm32: fix rx error handling") Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/1574323849-1909-1-git-send-email-fabrice.gasnier@st.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-21tty: Fix Kconfig indentation, continuedKrzysztof Kozlowski
Adjust indentation from seven spaces to tab (+optional two spaces) as in coding style with command like: $ sed -e 's/^ /\t/' -i */Kconfig Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/20191121132847.29015-1-krzk@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-21serial: serial_core: Perform NULL checks for break_ctl opsJiangfeng Xiao
Doing fuzz test on sbsa uart device, causes a kernel crash due to NULL pointer dereference: ------------[ cut here ]------------ Unable to handle kernel paging request at virtual address fffffffffffffffc pgd = ffffffe331723000 [fffffffffffffffc] *pgd=0000002333595003, *pud=0000002333595003, *pmd=00000 Internal error: Oops: 96000005 [#1] PREEMPT SMP Modules linked in: ping(O) jffs2 rtos_snapshot(O) pramdisk(O) hisi_sfc(O) Drv_Nandc_K(O) Drv_SysCtl_K(O) Drv_SysClk_K(O) bsp_reg(O) hns3(O) hns3_uio_enet(O) hclgevf(O) hclge(O) hnae3(O) mdio_factory(O) mdio_registry(O) mdio_dev(O) mdio(O) hns3_info(O) rtos_kbox_panic(O) uart_suspend(O) rsm(O) stp llc tunnel4 xt_tcpudp ipt_REJECT nf_reject_ipv4 iptable_filter ip_tables x_tables sd_mod xhci_plat_hcd xhci_pci xhci_hcd usbmon usbhid usb_storage ohci_platform ohci_pci ohci_hcd hid_generic hid ehci_platform ehci_pci ehci_hcd vfat fat usbcore usb_common scsi_mod yaffs2multi(O) ext4 jbd2 ext2 mbcache ofpart i2c_dev i2c_core uio ubi nand nand_ecc nand_ids cfi_cmdset_0002 cfi_cmdset_0001 cfi_probe gen_probe cmdlinepart chipreg mtdblock mtd_blkdevs mtd nfsd auth_rpcgss oid_registry nfsv3 nfs nfs_acl lockd sunrpc grace autofs4 CPU: 2 PID: 2385 Comm: tty_fuzz_test Tainted: G O 4.4.193 #1 task: ffffffe32b23f110 task.stack: ffffffe32bda4000 PC is at uart_break_ctl+0x44/0x84 LR is at uart_break_ctl+0x34/0x84 pc : [<ffffff8393196098>] lr : [<ffffff8393196088>] pstate: 80000005 sp : ffffffe32bda7cc0 x29: ffffffe32bda7cc0 x28: ffffffe32b23f110 x27: ffffff8393402000 x26: 0000000000000000 x25: ffffffe32b233f40 x24: ffffffc07a8ec680 x23: 0000000000005425 x22: 00000000ffffffff x21: ffffffe33ed73c98 x20: 0000000000000000 x19: ffffffe33ed94168 x18: 0000000000000004 x17: 0000007f92ae9d30 x16: ffffff8392fa6064 x15: 0000000000000010 x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000 x11: 0000000000000020 x10: 0000007ffdac1708 x9 : 0000000000000078 x8 : 000000000000001d x7 : 0000000052a64887 x6 : ffffffe32bda7e08 x5 : ffffffe32b23c000 x4 : 0000005fbc5b0000 x3 : ffffff83938d5018 x2 : 0000000000000080 x1 : ffffffe32b23c040 x0 : ffffff83934428f8 virtual start addr offset is 38ac00000 module base offset is 2cd4cf1000 linear region base offset is : 0 Process tty_fuzz_test (pid: 2385, stack limit = 0xffffffe32bda4000) Stack: (0xffffffe32bda7cc0 to 0xffffffe32bda8000) 7cc0: ffffffe32bda7cf0 ffffff8393177718 ffffffc07a8ec680 ffffff8393196054 7ce0: 000000001739f2e0 0000007ffdac1978 ffffffe32bda7d20 ffffff8393179a1c 7d00: 0000000000000000 ffffff8393c0a000 ffffffc07a8ec680 cb88537fdc8ba600 7d20: ffffffe32bda7df0 ffffff8392fa5a40 ffffff8393c0a000 0000000000005425 7d40: 0000007ffdac1978 ffffffe32b233f40 ffffff8393178dcc 0000000000000003 7d60: 000000000000011d 000000000000001d ffffffe32b23f110 000000000000029e 7d80: ffffffe34fe8d5d0 0000000000000000 ffffffe32bda7e14 cb88537fdc8ba600 7da0: ffffffe32bda7e30 ffffff8393042cfc ffffff8393c41720 ffffff8393c46410 7dc0: ffffff839304fa68 ffffffe32b233f40 0000000000005425 0000007ffdac1978 7de0: 000000000000011d cb88537fdc8ba600 ffffffe32bda7e70 ffffff8392fa60cc 7e00: 0000000000000000 ffffffe32b233f40 ffffffe32b233f40 0000000000000003 7e20: 0000000000005425 0000007ffdac1978 ffffffe32bda7e70 ffffff8392fa60b0 7e40: 0000000000000280 ffffffe32b233f40 ffffffe32b233f40 0000000000000003 7e60: 0000000000005425 cb88537fdc8ba600 0000000000000000 ffffff8392e02e78 7e80: 0000000000000280 0000005fbc5b0000 ffffffffffffffff 0000007f92ae9d3c 7ea0: 0000000060000000 0000000000000015 0000000000000003 0000000000005425 7ec0: 0000007ffdac1978 0000000000000000 00000000a54c910e 0000007f92b95014 7ee0: 0000007f92b95090 0000000052a64887 000000000000001d 0000000000000078 7f00: 0000007ffdac1708 0000000000000020 0000000000000000 0000000000000000 7f20: 0000000000000000 0000000000000010 000000556acf0090 0000007f92ae9d30 7f40: 0000000000000004 000000556acdef10 0000000000000000 000000556acdebd0 7f60: 0000000000000000 0000000000000000 0000000000000000 0000000000000000 7f80: 0000000000000000 0000000000000000 0000000000000000 0000007ffdac1840 7fa0: 000000556acdedcc 0000007ffdac1840 0000007f92ae9d3c 0000000060000000 7fc0: 0000000000000000 0000000000000000 0000000000000003 000000000000001d 7fe0: 0000000000000000 0000000000000000 0000000000000000 0000000000000000 Call trace: Exception stack(0xffffffe32bda7ab0 to 0xffffffe32bda7bf0) 7aa0: 0000000000001000 0000007fffffffff 7ac0: ffffffe32bda7cc0 ffffff8393196098 0000000080000005 0000000000000025 7ae0: ffffffe32b233f40 ffffff83930d777c ffffffe32bda7b30 ffffff83930d777c 7b00: ffffffe32bda7be0 ffffff83938d5000 ffffffe32bda7be0 ffffffe32bda7c20 7b20: ffffffe32bda7b60 ffffff83930d777c ffffffe32bda7c10 ffffff83938d5000 7b40: ffffffe32bda7c10 ffffffe32bda7c50 ffffff8393c0a000 ffffffe32b23f110 7b60: ffffffe32bda7b70 ffffff8392e09df4 ffffffe32bda7bb0 cb88537fdc8ba600 7b80: ffffff83934428f8 ffffffe32b23c040 0000000000000080 ffffff83938d5018 7ba0: 0000005fbc5b0000 ffffffe32b23c000 ffffffe32bda7e08 0000000052a64887 7bc0: 000000000000001d 0000000000000078 0000007ffdac1708 0000000000000020 7be0: 0000000000000000 0000000000000000 [<ffffff8393196098>] uart_break_ctl+0x44/0x84 [<ffffff8393177718>] send_break+0xa0/0x114 [<ffffff8393179a1c>] tty_ioctl+0xc50/0xe84 [<ffffff8392fa5a40>] do_vfs_ioctl+0xc4/0x6e8 [<ffffff8392fa60cc>] SyS_ioctl+0x68/0x9c [<ffffff8392e02e78>] __sys_trace_return+0x0/0x4 Code: b9410ea0 34000160 f9408aa0 f9402814 (b85fc280) ---[ end trace 8606094f1960c5e0 ]--- Kernel panic - not syncing: Fatal exception Fix this problem by adding NULL checks prior to calling break_ctl ops. Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/1574263133-28259-1-git-send-email-xiaojiangfeng@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-20tty: remove unused argument from tty_open_by_driver()Sudip Mukherjee
The argument 'inode' passed to tty_open_by_driver() was not being used. Remove the extra argument. Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Link: https://lore.kernel.org/r/20191120151709.14148-1-sudipm.mukherjee@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-20tty: Fix Kconfig indentationKrzysztof Kozlowski
Adjust indentation from spaces to tab (+optional two spaces) as in coding style with command like: $ sed -e 's/^ /\t/' -i */Kconfig Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/20191120133843.13189-1-krzk@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-18{tty: serial, nand: onenand}: samsung: rename to fix build warningSudip Mukherjee
Any arm config which has 'CONFIG_MTD_ONENAND_SAMSUNG=m' and 'CONFIG_SERIAL_SAMSUNG=m' gives a build warning: warning: same module names found: drivers/tty/serial/samsung.ko drivers/mtd/nand/onenand/samsung.ko Rename both drivers/tty/serial/samsung.c to drivers/tty/serial/samsung_tty.c and drivers/mtd/nand/onenand/samsung.c drivers/mtd/nand/onenand/samsung_mtd.c to fix the warning. Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Acked-by: Richard Weinberger <richard@nod.at> Link: https://lore.kernel.org/r/20191117202435.28127-1-sudipm.mukherjee@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-18serial: ifx6x60: add missed pm_runtime_disableChuhong Yuan
The driver forgets to call pm_runtime_disable in remove. Add the missed calls to fix it. Signed-off-by: Chuhong Yuan <hslester96@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191118024833.21587-1-hslester96@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-18serial: pl011: Fix DMA ->flush_buffer()Vincent Whitchurch
PL011's ->flush_buffer() implementation releases and reacquires the port lock. Due to a race condition here, data can end up being added to the circular buffer but neither being discarded nor being sent out. This leads to, for example, tcdrain(2) waiting indefinitely. Process A Process B uart_flush_buffer() - acquire lock - circ_clear - pl011_flush_buffer() -- release lock -- dmaengine_terminate_all() uart_write() - acquire lock - add chars to circ buffer - start_tx() -- start DMA - release lock -- acquire lock -- turn off DMA -- release lock // Data in circ buffer but DMA is off According to the comment in the code, the releasing of the lock around dmaengine_terminate_all() is to avoid a deadlock with the DMA engine callback. However, since the time this code was written, the DMA engine API documentation seems to have been clarified to say that dmaengine_terminate_all() (in the identically implemented but differently named dmaengine_terminate_async() variant) does not wait for any running complete callback to be completed and can even be called from a complete callback. So there is no possibility of deadlock if the DMA engine driver implements this API correctly. So we should be able to just remove this release and reacquire of the lock to prevent the aforementioned race condition. Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191118092547.32135-1-vincent.whitchurch@axis.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-14Revert "serial-uartlite: Move the uart register"Greg Kroah-Hartman
This reverts commit f33cf776617ba3b0f738cd70c31e0f62ea777a8d. As Johan says, this driver needs a lot more work and these changes are only going in the wrong direction: https://lkml.kernel.org/r/20190523091839.GC568@localhost Reported-by: Johan Hovold <johan@kernel.org> Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Cc: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-14Revert "serial-uartlite: Add get serial id if not provided"Greg Kroah-Hartman
This reverts commit 62104b280a5a5d999c562d8e8f4c6c4eb97fb013. As Johan says, this driver needs a lot more work and these changes are only going in the wrong direction: https://lkml.kernel.org/r/20190523091839.GC568@localhost Reported-by: Johan Hovold <johan@kernel.org> Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Cc: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-14Revert "serial-uartlite: Do not use static struct uart_driver out of probe()"Greg Kroah-Hartman
This reverts commit 3b209d253e7f8aa01fde0233d38a7239c8f7beb3. As Johan says, this driver needs a lot more work and these changes are only going in the wrong direction: https://lkml.kernel.org/r/20190523091839.GC568@localhost Reported-by: Johan Hovold <johan@kernel.org> Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Cc: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-14Revert "serial-uartlite: Add runtime support"Greg Kroah-Hartman
This reverts commit 0379b1163e509cfc4c18643b27231c04c78981ab. As Johan says, this driver needs a lot more work and these changes are only going in the wrong direction: https://lkml.kernel.org/r/20190523091839.GC568@localhost Reported-by: Johan Hovold <johan@kernel.org> Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Cc: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-14Revert "serial-uartlite: Change logic how console_port is setup"Greg Kroah-Hartman
This reverts commit d338838c09dee338dd86f479f554d18401068978. As Johan says, this driver needs a lot more work and these changes are only going in the wrong direction: https://lkml.kernel.org/r/20190523091839.GC568@localhost Reported-by: Johan Hovold <johan@kernel.org> Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Cc: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-14Revert "serial-uartlite: Use allocated structure instead of static ones"Greg Kroah-Hartman
This reverts commit a00d9db8952b44f4d165e5200fff03c80a84947f. As Johan says, this driver needs a lot more work and these changes are only going in the wrong direction: https://lkml.kernel.org/r/20190523091839.GC568@localhost Reported-by: Johan Hovold <johan@kernel.org> Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Cc: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-13riscv: don't allow selecting SBI based drivers for M-modeDamien Le Moal
When running in M-mode we can't use SBI based drivers. Add a new CONFIG_RISCV_SBI that drivers that do SBI calls can depend on instead. Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Reviewed-by: Anup Patel <anup@brainfault.org> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-11-13tty: serial: msm_serial: Use dma_request_chan() directly for channel requestPeter Ujfalusi
dma_request_slave_channel_reason() is: #define dma_request_slave_channel_reason(dev, name) \ dma_request_chan(dev, name) Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Link: https://lore.kernel.org/r/20191113094618.1725-3-peter.ujfalusi@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-13tty: serial: tegra: Use dma_request_chan() directly for channel requestPeter Ujfalusi
dma_request_slave_channel_reason() is: #define dma_request_slave_channel_reason(dev, name) \ dma_request_chan(dev, name) Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Link: https://lore.kernel.org/r/20191113094618.1725-4-peter.ujfalusi@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-13tty: serial: amba-pl011: Use dma_request_chan() directly for channel requestPeter Ujfalusi
dma_request_slave_channel_reason() is: #define dma_request_slave_channel_reason(dev, name) \ dma_request_chan(dev, name) Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Link: https://lore.kernel.org/r/20191113094618.1725-2-peter.ujfalusi@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-13serial-uartlite: Use allocated structure instead of static onesShubhrajyoti Datta
Remove the use of the static uartlite structure. Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Link: https://lore.kernel.org/r/1573555271-2579-2-git-send-email-shubhrajyoti.datta@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-13serial-uartlite: Change logic how console_port is setupShubhrajyoti Datta
Change logic how console_port is setup by using CON_ENABLED flag instead of index. There will be unique uart_console structure that's why code can't use id for console_port assignment. Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Link: https://lore.kernel.org/r/1573555271-2579-1-git-send-email-shubhrajyoti.datta@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-13tty: serial: pch_uart: correct usage of dma_unmap_sgPeng Fan
Per Documentation/DMA-API-HOWTO.txt, To unmap a scatterlist, just call: dma_unmap_sg(dev, sglist, nents, direction); .. note:: The 'nents' argument to the dma_unmap_sg call must be the _same_ one you passed into the dma_map_sg call, it should _NOT_ be the 'count' value _returned_ from the dma_map_sg call. However in the driver, priv->nent is directly assigned with value returned from dma_map_sg, and dma_unmap_sg use priv->nent for unmap, this breaks the API usage. So introduce a new entry orig_nent to remember 'nents'. Fixes: da3564ee027e ("pch_uart: add multi-scatter processing") Signed-off-by: Peng Fan <peng.fan@nxp.com> Link: https://lore.kernel.org/r/1573623259-6339-1-git-send-email-peng.fan@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-13tty: serial: imx: use the sg count from dma_map_sgPeng Fan
The dmaengine_prep_slave_sg needs to use sg count returned by dma_map_sg, not use sport->dma_tx_nents, because the return value of dma_map_sg is not always same with "nents". Fixes: b4cdc8f61beb ("serial: imx: add DMA support for imx6q") Signed-off-by: Peng Fan <peng.fan@nxp.com> Link: https://lore.kernel.org/r/1573108875-26530-1-git-send-email-peng.fan@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-13Remove every trace of SERIAL_MAGICPascal Terjan
This means removing support for checking magic in amiserial.c (SERIAL_PARANOIA_CHECK option), which was checking a magic field which doesn't currently exist in the struct. That code hasn't built at least since git. Removing the definition from the header is safe anyway as that code was from another driver and not including it. Signed-off-by: Pascal Terjan <pterjan@google.com> Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org> Link: https://lore.kernel.org/r/20191105192749.67533-1-pterjan@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-05tty: serial: fsl_lpuart: use the sg count from dma_map_sgPeng Fan
The dmaengine_prep_slave_sg needs to use sg count returned by dma_map_sg, not use sport->dma_tx_nents, because the return value of dma_map_sg is not always same with "nents". When enabling iommu for lpuart + edma, iommu framework may concatenate two sgs into one. Fixes: 6250cc30c4c4e ("tty: serial: fsl_lpuart: Use scatter/gather DMA for Tx") Cc: <stable@vger.kernel.org> Signed-off-by: Peng Fan <peng.fan@nxp.com> Link: https://lore.kernel.org/r/1572932977-17866-1-git-send-email-peng.fan@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-04Revert "tty:n_gsm.c: destroy port by tty_port_destroy()"Greg Kroah-Hartman
This reverts commit 7726fb53e75fa48714181efd00167e0734303afb. Jiri writes: On 24. 09. 19, 11:25, Xiaoming Ni wrote: > According to the comment of tty_port_destroy(): > When a port was initialized using tty_port_init, one has to destroy > the port by tty_port_destroy(); It continues with a part saying: Either indirectly by using tty_port refcounting (tty_port_put) or directly if refcounting is not used. So this should be reverted. Cc: Xiaoming Ni <nixiaoming@huawei.com> Reported-by: Jiri Slaby <jslaby@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-04tty: serial: uartlite: use clk_disable_unprepare to match clk_prepare_enableChuhong Yuan
The driver uses clk_prepare_enable in ulite_probe but uses clk_unprepare in ulite_remove, which does not match. Replace clk_unprepare with clk_disable_unprepare to fix it. Signed-off-by: Chuhong Yuan <hslester96@gmail.com> Link: https://lore.kernel.org/r/20191101085433.10399-1-hslester96@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-04serial: 8250-mtk: Use platform_get_irq_optional() for optional irqFrank Wunderlich
As platform_get_irq() now prints an error when the interrupt does not exist, this warnings are printed on bananapi-r2: [ 4.935780] mt6577-uart 11004000.serial: IRQ index 1 not found [ 4.962589] 11002000.serial: ttyS1 at MMIO 0x11002000 (irq = 202, base_baud = 1625000) is a ST16650V2 [ 4.972127] mt6577-uart 11002000.serial: IRQ index 1 not found [ 4.998927] 11003000.serial: ttyS2 at MMIO 0x11003000 (irq = 203, base_baud = 1625000) is a ST16650V2 [ 5.008474] mt6577-uart 11003000.serial: IRQ index 1 not found Fix this by calling platform_get_irq_optional() instead. now it looks like this: [ 4.872751] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled Fixes: 7723f4c5ecdb8d83 ("driver core: platform: Add an error message to platform_get_irq*()") Signed-off-by: Frank Wunderlich <frank-w@public-files.de> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191027062117.20389-1-frank-w@public-files.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-04serial: 8250_dw: Avoid double error messaging when IRQ absentAndy Shevchenko
Since the commit 7723f4c5ecdb ("driver core: platform: Add an error message to platform_get_irq*()") platform_get_irq() started issuing an error message. Thus, there is no need to have the same in the driver Fixes: 7723f4c5ecdb ("driver core: platform: Add an error message to platform_get_irq*()") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191023103558.51862-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-04tty: serial: msm_serial: Fix flow controlJeffrey Hugo
hci_qca interfaces to the wcn3990 via a uart_dm on the msm8998 mtp and Lenovo Miix 630 laptop. As part of initializing the wcn3990, hci_qca disables flow, configures the uart baudrate, and then reenables flow - at which point an event is expected to be received over the uart from the wcn3990. It is observed that this event comes after the baudrate change but before hci_qca re-enables flow. This is unexpected, and is a result of msm_reset() being broken. According to the uart_dm hardware documentation, it is recommended that automatic hardware flow control be enabled by setting RX_RDY_CTL. Auto hw flow control will manage RFR based on the configured watermark. When there is space to receive data, the hw will assert RFR. When the watermark is hit, the hw will de-assert RFR. The hardware documentation indicates that RFR can me manually managed via CR when RX_RDY_CTL is not set. SET_RFR asserts RFR, and RESET_RFR de-asserts RFR. msm_reset() is broken because after resetting the hardware, it unconditionally asserts RFR via SET_RFR. This enables flow regardless of the current configuration, and would undo a previous flow disable operation. It should instead de-assert RFR via RESET_RFR to block flow until the hardware is reconfigured. msm_serial should rely on the client to specify that flow should be enabled, either via mctrl() or the termios structure, and only assert RFR in response to those triggers. Fixes: 04896a77a97b ("msm_serial: serial driver for MSM7K onboard serial peripheral.") Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: stable <stable@vger.kernel.org> Reviewed-by: Andy Gross <agross@kernel.org> Link: https://lore.kernel.org/r/20191021154616.25457-1-jeffrey.l.hugo@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-04tty: rocket: reduce stack usageSudip Mukherjee
The build of xtensa allmodconfig gives warning of: In function 'get_ports.isra.0': warning: the frame size of 1040 bytes is larger than 1024 bytes Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Acked-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20191018161712.27807-1-sudipm.mukherjee@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-04tty: serial: lpuart: Add RS485 support for 32-bit uart flavourPhilippe Schenker
This commits adds RS485 support for LPUART hardware that uses 32-bit registers. These are typically found in i.MX8 processors. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Reviewed-by: Fugang Duan <fugang.duan@nxp.com> Link: https://lore.kernel.org/r/20191017141428.10330-3-philippe.schenker@toradex.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-04tty: serial: lpuart: Use defines that correspond to correct registerPhilippe Schenker
Use define from the 32-bit register description UARTMODIR_* instead of UARTMODEM_*. The value is the same, so there is no functional change. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Reviewed-by: Stefan Agner <stefan.agner@toradex.com> Reviewed-by: Fugang Duan <fugang.duan@nxp.com> Link: https://lore.kernel.org/r/20191017141428.10330-2-philippe.schenker@toradex.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-04tty: serial: lpuart: Remove unnecessary code from set_mctrlPhilippe Schenker
Currently flow control is not working due to lpuart32_set_mctrl that is clearing TXCTSE bit in all cases. This bit gets earlier setup by lpuart32_set_termios. As I read in Documentation set_mctrl is also not meant for hardware flow control rather than gpio setting and clearing a RTS signal. Therefore I guess it is safe to remove the whole code in lpuart32_set_mctrl. This was tested with console on a i.MX8QXP SoC. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Reviewed-by: Fugang Duan <fugang.duan@nxp.com> Link: https://lore.kernel.org/r/20191017141428.10330-1-philippe.schenker@toradex.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-03drivers: mcb: use symbol namespacesJohannes Thumshirn
Now that we have symbol namespaces, use them in MCB to not pollute the default namespace with MCB internals. Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Jessica Yu <jeyu@kernel.org> Reviewed-by: Michael Moese <mmoese@suse.de> Link: https://lore.kernel.org/r/20191016100158.1400-1-jthumshirn@suse.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>