| Age | Commit message (Collapse) | Author |
|---|
|
commit 3921426 (usb: dwc3: core: move
event buffer allocation out of
dwc3_core_init()) introduced a memory leak
of the coherent memory we use as event
buffers on dwc3 driver.
If the driver is compiled as a dynamically
loadable module and use constantly loads
and unloads the driver, we will continue
to leak the coherent memory allocated during
->probe() because dwc3_free_event_buffers()
is never called during ->remove().
Cc: <stable@vger.kernel.org> # v3.7 v3.8
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: xceiv: patches for v3.9 merge window
Two new PHY drivers coming here: one for Samsung,
one for OMAP. Both architectures are adding USB3
support to mainline kernel.
The PHY layer now allows us to have mulitple PHYs
of the same type, which is necessary for platforms
which provide more than one USB peripheral port.
There's also a few cleanups here: removal of __dev*
annotations, conversion of a cast to to_delayed_work(),
and mxs-phy learns about ->set_suspend.
|
|
Added dt support for dwc3 core and update the documentation with
device tree binding information. Getting a PHY is now done using
devm_usb_get_phy_by_phandle() for dt boot.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
No functional change. Stray statements where removed from dwc3 core.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Enabled the USB2 and USB3 PHY in probe by calling usb_phy_set_suspend
and disabled the PHYs on driver removal. When PM is implemented this
will be optimized to enable the PHYs only when needed.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 392142 moved event buffer allocation out of dwc3_core_init() but
event buffer allocation uses the cached copy of hwparams to determine
the number of event buffers and the caching is done in dwc3_core_init.
So moved dwc3_cache_hwparams function before dwc3_alloc_event_buffers so
that dwc3_alloc_event_buffers sees the correct number of event buffers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB dwc3 patches from Felipe:
"usb: dwc3: patches for v3.8
We can finaly drop HAVE_CLK dependency from exynos glue layer
now that clk API provides no-op stubs when it's not linked
into the kernel.
We're also switching over event buffer allocation to devm_kzalloc()
and moving the allocation out of dwc3_core_init() so that can be
re-used when implementing PM support for v3.9.
After the introduction of PLATFORM_DEVID_AUTO, we can also drop the
homebrew platform device ID handling we had on dwc3 core and let
driver core take care of that for us.
Exynos glue layer learns about DeviceTree and drops platform_data
support completely."
|
|
commit 380f0d2 (usb: dwc3: core: switch event
buffer allocation to devm_kzalloc()) was incomplete
leaving a trailing kfree(evt) in an error exit
path.
Fix this problem by removing the trailing kfree(evt).
Cc: Julia Lawall <julia.lawall@lip6.fr>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The lockless implementation of the unique id is quite impressive (:P)
but dirver's core can handle it, we can remove it and make our code a
little smaller.
Cc: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
We call usb_phy_init() from dwc3_core_init() during
probe, so adding usb_phy_shutdown() to dwc3_core_exit()
while removing the device so we don't keep PHYs
turned on, consuming power, unnecessarily.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch is in preparation for adding PM support
dwc3 driver. We want to re-use dwc3_core_init and
dwc3_core_exit() functions on resume() and suspend()
callbacks respectively.
Moving even buffer allocation away from dwc3_core_init()
will allow us to reuse the event buffer which was allocated
long ago on our probe() routine.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The rest of the driver is using devm_kzalloc() where possible
and this patch is just making event buffer allocation follow
the example.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This resolves the merge problems with:
drivers/usb/dwc3/gadget.c
drivers/usb/musb/tusb6010.c
that had been seen in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: dwc3: patches for v3.7 merge window
Some much needed changes for our dwc3 driver. First there's a
rework on the ep0 handling due to some Silicon issue we uncovered
which affects all users of this IP core (there's a missing
XferNotReady(DATA) event in some conditions). This issue which
show up as a SETUP transfers which wouldn't complete ever and
we would fail TD 7.06 of the Link Layer Test from USB-IF and
Lecroy's USB3 Exerciser.
We also fix a long standing bug regarding EP0 enable sequencing
where we weren't setting a particular bit (Ignore Sequence
Number). Since we never saw any problems caused by that, it
didn't deserve being sent to stable tree.
On this pull request we also fix Burst Size initialization which
should be done only in SuperSpeed and we were mistakenly setting
Burst Size to the maximum value on non-SuperSpeed mode. Again,
since we never saw any problems caused by that, we're not sending
this patch to stable.
There's also a memory ordering fix regarding usage of bitmaps in
dwc3 driver.
You will also find some sparse warnings fix, a fix for missed
isochronous packets when the endpoint is already busy, and a
fix for synchronization delay on dwc3_stop_active_transfer().
|
|
this will let us control PHYs on platforms which
need them.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Populate the resources for xhci afresh instead of directly using the
*struct resource* of core. *resource* structure has parent, sibling,
child pointers which should be filled only by resource API's. By
directly using the *resource* pointer of core in xhci, these parent,
sibling, child pointers are already populated even before
*platform_device_add* causing side effects.
Cc: stable@vger.kernel.org # v3.4, v3.5
Reported-by: Ruchika Kharwar <ruchika@ti.com>
Tested-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
As a bitmap is used for free/used. As a device freed
all memory operations must be scheduled before the bitmap
is manipulated.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This just guarantees that this piece of memory
will be marked uncachable.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Synopsys specification clearly states under section "Device Power-On or
Soft Reset" that DCTL.CSftRst=1 should be first step. So, just follow
what specification says.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Before taking core out of reset phy must be stable. So wait for 100ms
after clear phy reset.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The same event buffers will be reused when coming
out of hibernation, so we must reinitialize them
properly to avoid any mistakes.
While at that, also take dwc3_event_buffers_setup()
out of __devinit section.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: dwc3: patches for v3.5 merge window
This pull request contains one workaround for a Silicon
Issue found on all RTL releases prior to 2.20a, which
would cause a metastability state on Run/Stop bit.
We also have some patches implementing a few extra Standard
requests introduced by USB3 spec (Set SEL and Set Isoch Delay),
as well as one patch, which has been pending for a long time,
implementing LPM support.
Last, but not least, we are splitting the host address space
out of the dwc3 core driver otherwise xHCI won't be able to
request_mem_region() its own address space. This patch is
only needed because we are (as we should) re-using the xHCI
driver, which is a completely separate module.
Together with these three big changes, come a few extra preparatory
patches which most move code around, define macros and so on, as
well as a fix for Isochronous transfers which hasn't been triggered
before.
[ resolved conflicts and build error in drivers/usb/dwc3/gadget.c - gregkh]
|
|
This fix prevents a problem with dwc3 and host mode where
we were requesting the entire memory region in dwc3/core.c,
thus preventing xhci-plat from ever ioremapping its own address space.
Signed-off-by: Ido Shayevitz <idos@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Array should be freed together with event buffers, since it was
allocated dynamically.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Use the module_platform_driver macro.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Define DWC3_GCTL_SCALEDOWN_MASK and use it in place of
DWC3_GCTL_SCALEDOWN(3).
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
We always return zero instead of the id we found.
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
trivial patch, no functional changes
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
drivers/usb/dwc3/core.c and drivers/usb/dwc3/dwc3-omap.c
included 'linux/module.h' twice, remove the duplicates.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch enables to use devm_xxx functions during probing driver.
The devm_xxx series functions are able to release resource when the
driver is detatched. We can remove several codes to release resources
in the probe function.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
We need to dynamically re-size TxFifos for the
cases where default values will not do.
While at that, we create a simple function which,
for now, will just allocate one full packet fifo
space for each of the enabled endpoints.
This can be improved later in order to allow for
better throughput by allocating more space for
endpoints which could make good use of that like
isochronous and bulk.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (232 commits)
USB: Add USB-ID for Multiplex RC serial adapter to cp210x.c
xhci: Clean up 32-bit build warnings.
USB: update documentation for usbmon
usb: usb-storage doesn't support dynamic id currently, the patch disables the feature to fix an oops
drivers/usb/class/cdc-acm.c: clear dangling pointer
drivers/usb/dwc3/dwc3-pci.c: introduce missing kfree
drivers/usb/host/isp1760-if.c: introduce missing kfree
usb: option: add ZD Incorporated HSPA modem
usb: ch9: fix up MaxStreams helper
USB: usb-skeleton.c: cleanup open_count
USB: usb-skeleton.c: fix open/disconnect race
xhci: Properly handle COMP_2ND_BW_ERR
USB: remove dead code from suspend/resume path
USB: add quirk for another camera
drivers: usb: wusbcore: Fix dependency for USB_WUSB
xhci: Better debugging for critical host errors.
xhci: Be less verbose during URB cancellation.
xhci: Remove debugging about ring structure allocation.
xhci: Remove debugging about toggling cycle bits.
xhci: Remove debugging for individual transfers.
...
|
|
All our revision macros are defined with the entire
32-bits which we read from GSNPSID register, so we
must cache all 32-bits properly rather than masking
the top 16-bits.
This will fix all revision checks we have on current
driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
We mask the correct bits within the wrong register. The power
optimization mode is stored hwparam1 register and not in hwparam0.
Reported-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
A few inits like the scale value or the removal of the DISSCRAMBLE is
done in the gadget code however it touches a general register.
Move this piece to the core.c file since it is likely to be requied by
both, parts of the core (device and host).
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
There are two where need to set operational mode:
- during initialization while we decide to run in host,device or DRD
mode
- at runtime via the debugfs interface.
This patch provides a new function which sets the operational mode and
moves its initialiation to the mode switch instead in the gadget code
itself.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
hardware will tell us how many event buffers we
need to support, so let's allocate the array
dynamically too.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
if we want to support situations where we have
both SoC and PCIe versions of the IP on the same
platform, we need to have sequential numbers between
them, otherwise we will still have name collisions.
Because of that, we need to move dwc3_get/put_device_id()
to core.c and export that symbol to be used by glue
layers.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
We can have three modules here: dwc3.ko, dwc3-omap.ko and dwc3-pci.ko.
The later have already ids-aliases for probing and is fine. The omap
module has alias for DT but lacks alias for the "native"
platform_device. Maybe we should get rid of it and stick to the DT name?
Both glue modules create a new device for which the dwc3.ko module is
responsible and that one lacks the platform alias.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The Designware USB3 IP can be configured with
an internal xHCI. If we're running on such a
version, let's start the xHCI stack.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
There's no need to add driver_data for something
we can fetch from HW.
This also makes our id_table unnecessary - at least
for now -, so we also remove it on the same patch.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This will allow us to only allocate memory when
we actually need.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
this is mainly for testing. In order to be able
to test if we're enumerating correctly on all
speeds, let that be controlled by a module
parameter.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
These files uses the full set of MODULE_ macros and so need to
include module.h directly.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
cache the contents of GHWPARAMS* registers in
our device structure for easy access.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Some people think that this line is not compatible with the GPL. The
statement was required due to the Buenos Aires Convention and is now
deprecated. I remove it because it is said that it is pointless nowdays.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
We need that header because of THIS_MODULE.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
