| Age | Commit message (Collapse) | Author |
|---|
|
Add 'match_ep' callback to utilize chip-specific knowledge in endpoint matching
process. Function does the same that was done by chip-specific code inside
of epautoconf. Now this code can be removed from there to separate generic code
from platform specific logic.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Gadget must be informed about disconnection when pullup is removed.
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Reset configuration in ep_cfg on disable to physically disable the
endpoint.
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
USB3380 enhanced mode allows GPEP to be used in both IN and OUT
directions. However, IN and OUT endpoints must use same USB endpoint
address (bEndpointAddress). Fix this by setting the ep_cfg.ep_number
during initialization and keep it in net2280_enable()
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
USB3380 in enhanced mode has 4 IN and 4 OUT endpoints. Check
interrupts for all of them.
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Default 0 value can result in unintentional zlp for IN endpoints.
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
USB3380 ep_cfg.direction bit is reserved in enhanced mode. Don't set
it.
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
If ep->dma is set, abort_dma() takes care of dma clean-up. If ep->dma
is not set, unconditionally reset dma channel.
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Sequence number can be out of sync if endpoint is disabled after some
data transfers and enabled again. Reset it to stay in sync with host.
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
ep_cfg.IN_EP_ENABLE is only valid in advance mode.
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Silence the following warning:
drivers/usb/gadget/udc/net2280.c:3176:33: warning: context imbalance in
'handle_stat1_irqs' - unexpected unlock
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
net2280_start can be called with pullup disabled. Don't set
softconnect flag in it. Let net2280_pullup handle the connection part.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Hopefully, these prints will help localize the problems faster.
[ balbi@ti.com: removed 2 unnecessary OOM error messages ]
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Remove fiforegs from struct net2280 and net2280_ep as it is unused.
By the way, ep->fiforegs = &dev->fiforegs[i] assignment is incorrect.
It should be ep->fiforegs = &dev->fiforegs[ne[i]], but it doesn't
matter now.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Each struct usb_ep added for net2280 can be used in either direction.
Whereas, each struct usb_ep for usb3380 has fixed direction. Use
ep_autoconf compatible names so that endpoint with correct direction
can be selected.
Name sequence is due to the logic in usb_reinit_338x() in ne[] and
ep_reg_addr[].
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Fix sparse warning
Fixes: cb442ee1592d2681 (usb: gadget: udc: net2280: Re-enable dynamic debug messages)
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Some debug messages were not build due to unconditional #if 0.
These messages are very useful for debugging and the user can enable
them on demand via dynamic debug.
If they are not enabled the performance is not affected.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
ASSERT_OUT_NAKING was only called by out_flush and was hidden behind a
ifdef.
This patch moves the inline function into out_flush and remove the
ifdef. The user can decide to print the debug message or not via dynamic
printk
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
After fix superspeed dma_done was applied we can simplify the code by
removing the duplicated dma_done and letting the function check if there
are more completed dma transactions.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Function resume_dma is not used, remove it.
The reason the compiler did not catch this dead code is the inline
modifier.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Once the defect 7374 is patched, there is no reason the keep reading the
idx scratch register.
Cache the content of the scratch idx register on device flag.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Do not duplicate the code for the else branch of the condition.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
We can use the same function for both families of chips and also remove
the ep_stop_dma() function.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
irqs_superspeed calls ep_stall instead of set/clear_halt, due to a
workaround for SS seqnum. Create a function with the workaround and
call set/clear_halt instead.
This way we can compare the code of super/normal speed and it is easier
to follow the code.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Field is_halt is never used by any function.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
ep_stdrsp was only called by handle_stat0_irqs_superspeed and with
always the same flags.
Remove the function and replace the call by the code inside the
function, since it is very simple once the dead code is removed.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
restart_dma is not used before it is declaration. Therefore we can
remove this definition.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Remove dma_started field from net2280_ep structure, since it is not used
by any function.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
use_dma parameter was designed to enable the dma on the chip. It was
enabled by default.
It comes from the time when the dma was not reliable. Now it has been
working ok in production.
This patch removes this parameter.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Parameter use_msi was used to enable msi irq on usb338x chips, it was
enabled by default.
There is no reason to prefer non-msi irq on usb338x, and it falls back
to non msi on error.
Therefore remove this option.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch removes the full_speed parameter used force full-speed
operation.
It was designed exclusively for testing purposes, and there is no
reason to maintain this in a production kernel.
Reverts: 2f0760774711c957c395b31131b848043af98edf
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
use_dma_chaining module parameter was designed to avoid creating one irq
per package on a group of packages (with the help of the driver's flag
no_interrupt).
Unfortunately, when this parameter is enabled, the driver fails to work
on both net2280 and 3380 chips.
This patch removes this parameter, which was disabled by default.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Parameter three in function call dma_done() is incorrect.
Move use of variable 'tmp' after if-condition.
Signed-off-by: Mario Schuknecht <mario.schuknecht@dresearch-fe.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch adds support for the new udc-core reset notifier to the
net2280 driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
now that no UDC driver relies on the extra
'driver' argument to ->udc_stop(), we can
safely remove it.
This commit is based on previous work by
Robert Baldyga <r.baldyga@samsung.com> which
can be found at [1]; however that patch turned
out to have a high probability of regressing
many UDC drivers because of a blind search & replace
s/driver/$udc->driver/ which caused the 'driver'
argument to stop_activity() to be a valid non-NULL
pointer when it should be NULL, thus causing UDCs
to mistakenly call gadget driver's ->disconnect()
callback.
[1] http://markmail.org/message/x5zneg4xea4zntab
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
now that we provide generic register/unregister
debugging messages from udc-core, we can remove
the same messages from this driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
future patches will remove the extra 'driver'
argument to ->udc_stop(), in order to do that,
we must make sure that our UDC does not rely
on it first.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Use the recently introduced usb_gadget_giveback_request() in favor of
direct invocation of the completion routine.
All places in drivers/usb/ matching "[-.]complete(" were replaced with a
call to usb_gadget_giveback_request(). This was compile-tested with all
ARM drivers enabled and runtime-tested for musb.
Signed-off-by: Michal Sojka <sojka@merica.cz>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Without this patch, some hosts keep restarting indefinitely the target.
Fixes: ae8e530 (usb: gadget: net2280: Code Cleanup)
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
No functional changes, just fixing one easy
to spot sparse error.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The drivers/usb/gadget directory contains many files.
Files which are related can be distributed into separate directories.
This patch moves the UDC drivers into a separate directory.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
