summaryrefslogtreecommitdiff
path: root/drivers/usb/phy/phy-mxs-usb.c
AgeCommit message (Collapse)Author
2024-10-04usb: Switch back to struct platform_driver::remove()Uwe Kleine-König
After commit 0edb555a65d1 ("platform: Make platform_driver::remove() return void") .remove() is (again) the right callback to implement for platform drivers. Convert all platform drivers below drivers/usb to use .remove(), with the eventual goal to drop struct platform_driver::remove_new(). As .remove() and .remove_new() have the same prototypes, conversion is done by just changing the structure member name in the driver initializer. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com> Link: https://lore.kernel.org/r/20240924084329.53094-2-u.kleine-koenig@baylibre.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-08-13usb: phy: mxs: enable weak 1p1 regulator for imx6ul during suspendXu Yang
1p1 is off when the system enters suspend at i.MX6UL. It cause the PHY get wrong USB DP/DM value, then unexpected wakeup may occur if USB wakeup enabled. This will enable weak 1p1 during PHY suspend if vbus exist. So USB DP/DM is correct when system suspend. Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Link: https://lore.kernel.org/r/20240726113207.3393247-5-xu.yang_2@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-08-13usb: phy: mxs: add wakeup enable for imx7ulpXu Yang
This wakeup setting can enable USB wakeup function even the controller's power is lost, and both A7 and M4 are in VLLS mode. Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Reviewed-by: Peter Chen <peter.chen@kernel.org> Link: https://lore.kernel.org/r/20240726113207.3393247-4-xu.yang_2@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-08-13usb: phy: mxs: keep USBPHY2's clk always onXu Yang
IP require keep USBPHY2's clk always on, so USBPHY2 (PLL7) power can be controlled by suspend signal. USB remote wakeup needs resume signal be sent out as soon as possible to match USB requirements. Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Reviewed-by: Peter Chen <peter.chen@kernel.org> Link: https://lore.kernel.org/r/20240726113207.3393247-2-xu.yang_2@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-08-13usb: phy: mxs: enable regulator phy-3p0 to improve signal qualiltyXu Yang
Enable regulator 'phy-3p0' to pass eye diagram test since it improve signal qualilty. Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Reviewed-by: Peter Chen <peter.chen@kernel.org> Link: https://lore.kernel.org/r/20240726113207.3393247-1-xu.yang_2@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-01-04usb: phy: mxs: remove CONFIG_USB_OTG condition for mxs_phy_is_otg_host()Xu Yang
When CONFIG_USB_OTG is not set, mxs_phy_is_otg_host() will always return false. This behaviour is wrong. Since phy.last_event will always be set for either host or device mode. Therefore, CONFIG_USB_OTG condition can be removed. Fixes: 5eda42aebb76 ("usb: phy: mxs: fix getting wrong state with mxs_phy_is_otg_host()") cc: <stable@vger.kernel.org> Acked-by: Peter Chen <peter.chen@kernel.org> Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Link: https://lore.kernel.org/r/20231228110753.1755756-3-xu.yang_2@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-07-25usb: phy: mxs: disconnect line when USB charger is attachedXu Yang
For mxs PHY, if there is a vbus but the bus is not enumerated, we need to force the dp/dm as SE0 from the controller side. If not, there is possible USB wakeup due to unstable dp/dm, since there is possible no pull on dp/dm, such as there is a USB charger on the port. Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Acked-by: Peter Chen <peter.chen@kernel.org> Link: https://lore.kernel.org/r/20230627110353.1879477-3-xu.yang_2@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-07-25usb: phy: mxs: fix getting wrong state with mxs_phy_is_otg_host()Xu Yang
The function mxs_phy_is_otg_host() will return true if OTG_ID_VALUE is 0 at USBPHY_CTRL register. However, OTG_ID_VALUE will not reflect the real state if the ID pin is float, such as Host-only or Type-C cases. The value of OTG_ID_VALUE is always 1 which means device mode. This patch will fix the issue by judging the current mode based on last_event. The controller will update last_event in time. Fixes: 7b09e67639d6 ("usb: phy: mxs: refine mxs_phy_disconnect_line") Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Acked-by: Peter Chen <peter.chen@kernel.org> Link: https://lore.kernel.org/r/20230627110353.1879477-2-xu.yang_2@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-07-25usb: Explicitly include correct DT includesRob Herring
The DT of_device.h and of_platform.h date back to the separate of_platform_bus_type before it as merged into the regular platform bus. As part of that merge prepping Arm DT support 13 years ago, they "temporarily" include each other. They also include platform_device.h and of.h. As a result, there's a pretty much random mix of those include files used throughout the tree. In order to detangle these headers and replace the implicit includes with struct declarations, users need to explicitly include the correct includes. Acked-by: Herve Codina <herve.codina@bootlin.com> Signed-off-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20230718143027.1064731-1-robh@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-23usb: phy: mxs: Convert to platform remove callback returning voidUwe Kleine-König
The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is (mostly) ignored and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Frank Li <Frank.li@nxp.com> Link: https://lore.kernel.org/r/20230319092428.283054-9-u.kleine-koenig@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-16usb: Use of_property_present() for testing DT property presenceRob Herring
It is preferred to use typed property access functions (i.e. of_property_read_<type> functions) rather than low-level of_get_property/of_find_property functions for reading properties. As part of this, convert of_get_property/of_find_property calls to the recently added of_property_present() helper when we just want to test for presence of a property and nothing more. Signed-off-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20230310144728.1545786-1-robh@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-08-31usb: phy: mxs: fix MXS_PHY_TX_CAL45_MIN and MXS_PHY_TX_CAL45_MAXFrank Li
According to spec: 0000 +19.95% .... 1111 -21.68% 45 * (1 + 19.95%) = 53.9775 45 * (1 - 21.68%) = 35.244 Fix MXS_PHY_TX_CAL45_MIN from 30 to 35 Fix MXS_PHY_TX_CAL45_MAX from 55 to 54 Signed-off-by: Frank Li <Frank.Li@nxp.com> Link: https://lore.kernel.org/r/20220829153124.2791210-2-Frank.Li@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-01-18usb: phy: phy-mxs-usb: Use of_device_get_match_data()Fabio Estevam
The retrieval of driver data via of_device_get_match_data() can make the code simpler. Use of_device_get_match_data() to simplify the code. Acked-by: Peter Chen <peter.chen@nxp.com> Acked-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Fabio Estevam <festevam@gmail.com> Link: https://lore.kernel.org/r/20210118152615.1644861-1-festevam@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-10-04usb: phy: mxs: use devm_platform_ioremap_resource() to simplify codeYueHaibing
Use devm_platform_ioremap_resource() to simplify the code a bit. This is detected by coccinelle. Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Link: https://lore.kernel.org/r/20190904084827.24108-1-yuehaibing@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-07-03usb: phy: phy-mxs-usb: add imx7ulp supportPeter Chen
At imx7ulp, the USB related analog register is located in PHY register region too, so we need to control PLL at PHY driver directly. Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-06-06usb: phy: mxs: Disable external charger detect in mxs_phy_hw_init()Andrey Smirnov
Since this driver already handles changer detction state, copy the workaround code currently residing in arch/arm/mach-imx/anatop.c into this drier to consolidate the places modifying it. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Chris Healy <cphealy@gmail.com> Cc: Felipe Balbi <balbi@kernel.org> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: linux-usb@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Reviewed-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-09-20usb: phy: mxs: fix spelling mistake "stardard" -> "standard"Colin Ian King
Trivial fix to spelling mistake in dev_dbg message Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-08usb: phy: mxs: Staticize mxs_charger_secondary_detection()Fabio Estevam
mxs_charger_secondary_detection() is only used in this file, so make it static. This fixes the following sparse warning: drivers/usb/phy/phy-mxs-usb.c:581:23: warning: symbol 'mxs_charger_secondary_detection' was not declared. Should it be static? Acked-by: Jun Li <jun.li@nxp.com> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-02-12usb: phy: mxs: Fix NULL pointer dereference on i.MX23/28Fabio Estevam
Commit e93650994a95 ("usb: phy: mxs: add usb charger type detection") causes the following kernel hang on i.MX28: [ 2.207973] usbcore: registered new interface driver usb-storage [ 2.235659] Unable to handle kernel NULL pointer dereference at virtual address 00000188 [ 2.244195] pgd = (ptrval) [ 2.246994] [00000188] *pgd=00000000 [ 2.250676] Internal error: Oops: 5 [#1] ARM [ 2.254979] Modules linked in: [ 2.258089] CPU: 0 PID: 1 Comm: swapper Not tainted 4.15.0-rc8-next-20180117-00002-g75d5f21 #7 [ 2.266724] Hardware name: Freescale MXS (Device Tree) [ 2.271921] PC is at regmap_read+0x0/0x5c [ 2.275977] LR is at mxs_phy_charger_detect+0x34/0x1dc mxs_phy_charger_detect() makes accesses to the anatop registers via regmap, however i.MX23/28 do not have such registers, which causes a NULL pointer dereference. Fix the issue by doing a NULL check on the 'regmap' pointer. Fixes: e93650994a95 ("usb: phy: mxs: add usb charger type detection") Cc: <stable@vger.kernel.org> # v4.15 Reviewed-by: Li Jun <jun.li@nxp.com> Acked-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-11-07USB: phy: Remove redundant license textGreg Kroah-Hartman
Now that the SPDX tag is in all USB files, that identifies the license in a specific and legally-defined manner. So the extra GPL text wording can be removed as it is no longer needed at all. This is done on a quest to remove the 700+ different ways that files in the kernel describe the GPL license text. And there's unneeded stuff like the address (sometimes incorrect) for the FSF which is never needed. No copyright headers or other non-license-description text was removed. Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Jonathan Hunter <jonathanh@nvidia.com> Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-04USB: add SPDX identifiers to all remaining files in drivers/usb/Greg Kroah-Hartman
It's good to have SPDX identifiers in all files to make it easier to audit the kernel tree for correct licenses. Update the drivers/usb/ and include/linux/usb* files with the correct SPDX license identifier based on the license text in the file itself. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This work is based on a script and data from Thomas Gleixner, Philippe Ombredanne, and Kate Stewart. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Philippe Ombredanne <pombredanne@nexb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> Acked-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-19usb: phy: mxs: add usb charger type detectionLi Jun
mxs phy has data pin contact and usb charger detector blocks which can be controlled by software to detect charger type for SDP, CDP and DCP. Reviewed-by: Baolin Wang <baolin.wang@linaro.org> Signed-off-by: Li Jun <jun.li@nxp.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-25usb: phy: mxs: Add DT bindings to configure TX settingsJaret Cantu
The TX settings can be calibrated for particular hardware. The phy is reset by Linux, so this cannot be handled by the bootloader. The TRM mentions that the maximum resistance should be used for the DN/DP calibration in order to pass USB certification. The values for the TX registers are poorly described in the TRM. The meanings of the register values were taken from another NXP-provided document: https://community.nxp.com/message/566147#comment-566912 Acked-by: Peter Chen <peter.chen@nxp.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Jaret Cantu <jaret.cantu@timesys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-02-03usb: phy: mxs: declare variable with initialized valueLi Jun
Initialize vbus_value to be 0 since it's possible not to assign any value before judgement. Acked-by: Peter Chen <peter.chen@nxp.com Signed-off-by: Li Jun <jun.li@nxp.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2015-11-19usb: phy: mxs: add "fsl,imx6ul-usbphy" compatible stringPeter Chen
Add "fsl,imx6ul-usbphy" compatible string for iMX6ul usb phy Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Li Jun <jun.li@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-11-17usb: phy: phy-mxs-usb: fix a possible NULL dereferenceLABBE Corentin
of_match_device could return NULL, and so cause a NULL pointer dereference later. Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-08-05usb: phy: phy-mxs-usb: Simplify return statementSaurabh Karajgaonkar
Replace redundant variable use in return statement. Signed-off-by: Saurabh Karajgaonkar <skarajga@visteon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-07-06usb: phy: mxs: suspend to RAM causes NULL pointer dereferenceStefan Wahren
Triggering suspend to RAM via sysfs on a i.MX28 causes a NULL pointer dereference. This patch avoids the oops in mxs_phy_get_vbus_status() by aborting since there is no syscon available. Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Fixes: efdbd3a5d6e ("usb: phy: mxs: do not set PWD.RXPWD1PT1 for low speed connection") CC: <stable@vger.kernel.org> # 4.0 Acked-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: phy: mxs: add delay before set phyctrl.clkgatePeter Chen
There is a request from IC engineer that if we doesn't set phypwd as 0xffffffff, we need to delay about five 32Khz cycles before set phy's pwd register, otherwise, the wakeup signal may can't wake up controller. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: phy: mxs: do not set PWD.RXPWD1PT1 for low speed connectionPeter Chen
At very rare cases, the SoF will not send out after resume with low speed connection. The workaround is do not power down PWD.RXPWD1PT1 bit during the suspend. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: phy: mxs: refine mxs_phy_disconnect_lineLi Jun
For non-otg mode, we keep the usage of disconnect line between phy analog and digital unchanging; for otg mode, at peripheral role, we keep the usage unchanging too, at host role, the digital part needs to know dp/dm change to respond device's data pulse when it is at low power mode. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Li Jun <b47624@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-27usb: phy: mxs: don't need IP fix for imx6sxPeter Chen
The RLT code has already done it, so no software operation is needed. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: phy: phy-mxs-usb: do not depend on speed for disconnect notifierPeter Chen
For some user cases, like plug out and replug in usb device during the system suspend, the speed negotiation will be error due to host doesn't know the device's disconnection, and it still hopes the high speed device, but the device backs to "powered" state which its high speed termination is not enabled, the usb core calls the PHY's disconnect notifier with "full speed", it will NOT take effect at all. If the usb core calls disconnect notifer, the port change must happen, so it is safe to disable high speed disconenct detector, since connect notifier will be called soon if the device is still connected on the port, and we will enable high speed disconnect detector at that time. Acked-by: Li Jun <b47624@freescale.com> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: phy: phy-mxs-usb: add power down and disable wakeup for .shutdownPeter Chen
When we shut down the PHY, we need to power down all PHY's functions as well as disable wakeup, it is the opposite operation we do at .init. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-12-14Merge tag 'driver-core-3.19-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core update from Greg KH: "Here's the set of driver core patches for 3.19-rc1. They are dominated by the removal of the .owner field in platform drivers. They touch a lot of files, but they are "simple" changes, just removing a line in a structure. Other than that, a few minor driver core and debugfs changes. There are some ath9k patches coming in through this tree that have been acked by the wireless maintainers as they relied on the debugfs changes. Everything has been in linux-next for a while" * tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits) Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries" fs: debugfs: add forward declaration for struct device type firmware class: Deletion of an unnecessary check before the function call "vunmap" firmware loader: fix hung task warning dump devcoredump: provide a one-way disable function device: Add dev_<level>_once variants ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries ath: use seq_file api for ath9k debugfs files debugfs: add helper function to create device related seq_file drivers/base: cacheinfo: remove noisy error boot message Revert "core: platform: add warning if driver has no owner" drivers: base: support cpu cache information interface to userspace via sysfs drivers: base: add cpu_device_create to support per-cpu devices topology: replace custom attribute macros with standard DEVICE_ATTR* cpumask: factor out show_cpumap into separate helper function driver core: Fix unbalanced device reference in drivers_probe driver core: fix race with userland in device_add() sysfs/kernfs: make read requests on pre-alloc files use the buffer. sysfs/kernfs: allow attributes to request write buffer be pre-allocated. fs: sysfs: return EGBIG on write if offset is larger than file size ...
2014-11-03usb: phy: phy-mxs-usb: delete unnecessary 'out of memory' messagesPeter Chen
The memory subsystem has already had similar message for it. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-10-20usb: phy: drop owner assignment from platform_driversWolfram Sang
A platform_driver does not need to set an owner, it will be populated by the driver core. Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-09-16Merge tag 'v3.17-rc5' into nextFelipe Balbi
Linux 3.17-rc5 Signed-off-by: Felipe Balbi <balbi@ti.com> Conflicts: Documentation/devicetree/bindings/usb/mxs-phy.txt drivers/usb/phy/phy-mxs-usb.c
2014-09-03usb: phy: mxs: add imx6sx supportPeter Chen
Add imx6sx support Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-08-27usb: phy: mxs: Add VF610 USB PHY supportStefan Agner
This adds support for the USB PHY in Vybrid VF610. We assume that the disconnection without VBUS is also needed for Vybrid. Tests showed, without MXS_PHY_NEED_IP_FIX, enumeration of devices behind a USB Hub fails with errors: [ 215.163507] usb usb1-port1: cannot reset (err = -32) [ 215.170498] usb usb1-port1: cannot reset (err = -32) [ 215.185120] usb usb1-port1: cannot reset (err = -32) [ 215.191345] usb usb1-port1: cannot reset (err = -32) [ 215.202487] usb usb1-port1: cannot reset (err = -32) [ 215.207718] usb usb1-port1: Cannot enable. Maybe the USB cable is bad? [ 215.219317] usb usb1-port1: unable to enumerate USB device Hence we also enable the MXS_PHY_NEED_IP_FIX flag. Acked-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-03-05usb: phy: mxs: Add sync time after controller clear phcdPeter Chen
After clear portsc.phcd, PHY needs 200us stable time for switch 32K clock to AHB clock. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-03-05usb: phy: mxs: Add system suspend/resume APIPeter Chen
We need this to keep PHY's power on or off during the system suspend mode. If we need to enable USB wakeup, then we must keep PHY's power being on during the system suspend mode. Otherwise, we need to keep PHY's power being off to save power. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-03-05usb: phy: mxs: Add implementation of set_wakeupPeter Chen
When we need the PHY can be waken up by external signals, we can call this API. Besides, we call mxs_phy_disconnect_line at this API to close the connection between USB PHY and controller, after that, the line state from controller is SE0. Once the PHY is out of power, without calling mxs_phy_disconnect_line, there are unknown wakeups due to dp/dm floating at device mode. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-03-05usb: phy: mxs: add controller idPeter Chen
It is used to access un-regulator registers according to different controllers. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-03-05usb: phy: mxs: Enable IC fixes for related SoCsPeter Chen
Two PHY bugs are fixed by IC logic, but these bits are not enabled by default, so we enable them at driver. The two bugs are: MXS_PHY_ABNORMAL_IN_SUSPEND and MXS_PHY_SENDING_SOF_TOO_FAST which are described at code. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-03-05usb: phy: mxs: change description of usb device speedPeter Chen
Change "high speed" to "HS" Change "non-high speed" to "FS/LS" Implementation of notify_suspend and notify_resume will be different according to mxs_phy_data->flags. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-03-05usb: phy: mxs: Add anatop regmapPeter Chen
It is needed by imx6 SoC series, but not for imx23 and imx28. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-03-05usb: phy: mxs: Add auto clock and power settingPeter Chen
The auto setting is used to open related power and clocks automatically after receiving wakeup signal. With this feature, the PHY's clock and power can be recovered correctly from low power mode, it is guaranteed by IC logic. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-03-05usb: phy: mxs: Add platform judgement codePeter Chen
The mxs-phy has several bugs and features at different versions, the driver code can get it through of_device_id.data. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-12-19Merge tag 'v3.13-rc4' into nextFelipe Balbi
Linux 3.13-rc4 * tag 'v3.13-rc4': (1001 commits) Linux 3.13-rc4 null_blk: mem garbage on NUMA systems during init radeon_pm: fix oops in hwmon_attributes_visible() and radeon_hwmon_show_temp_thresh() Revert "selinux: consider filesystem subtype in policies" igb: Fix for issue where values could be too high for udelay function. i40e: fix null dereference ARM: fix asm/memory.h build error dm array: fix a reference counting bug in shadow_ablock dm space map: disallow decrementing a reference count below zero mm: memcg: do not allow task about to OOM kill to bypass the limit mm: memcg: fix race condition between memcg teardown and swapin thp: move preallocated PTE page table on move_huge_pmd() mfd/rtc: s5m: fix register updating by adding regmap for RTC rtc: s5m: enable IRQ wake during suspend rtc: s5m: limit endless loop waiting for register update rtc: s5m: fix unsuccesful IRQ request during probe drivers/rtc/rtc-s5m.c: fix info->rtc assignment include/linux/kernel.h: make might_fault() a nop for !MMU drivers/rtc/rtc-at91rm9200.c: correct alarm over day/month wrap procfs: also fix proc_reg_get_unmapped_area() for !MMU case ... Signed-off-by: Felipe Balbi <balbi@ti.com>
generated by cgit (git 2.34.1) at 2025-05-31 20:46:52 +0000