summaryrefslogtreecommitdiff
path: root/drivers/usb/serial
AgeCommit message (Collapse)Author
2019-08-28USB: serial: ftdi_sio: add support for FT232H CBUS gpiosMatthew Michilot
Enable support for cbus gpios on FT232H. The cbus configuration is stored in two words in the EEPROM at byte-offset 0x1a with the mux config for ACBUS5, ACBUS6, ACBUS8 and ACBUS9 (only pins that can be configured as I/O mode). Tested using FT232H by configuring one ACBUS pin at a time. Reviewed-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Matthew Michilot <matthew.michilot@gmail.com> [ johan: fix copy-paste error in commit message ] Signed-off-by: Johan Hovold <johan@kernel.org>
2019-08-15USB: serial: option: add the BroadMobi BM818 cardBob Ham
Add a VID:PID for the BroadMobi BM818 M.2 card T: Bus=01 Lev=03 Prnt=40 Port=03 Cnt=01 Dev#= 44 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2020 ProdID=2060 Rev=00.00 S: Manufacturer=Qualcomm, Incorporated S: Product=Qualcomm CDMA Technologies MSM C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=(none) I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) Signed-off-by: Bob Ham <bob.ham@puri.sm> Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca> Cc: stable <stable@vger.kernel.org> [ johan: use USB_DEVICE_INTERFACE_CLASS() ] Signed-off-by: Johan Hovold <johan@kernel.org>
2019-08-15USB: serial: option: Add Motorola modem UARTsTony Lindgren
On Motorola Mapphone devices such as Droid 4 there are five USB ports that do not use the same layout as Gobi 1K/2K/etc devices listed in qcserial.c. So we should use qcaux.c or option.c as noted by Dan Williams <dan.j.williams@intel.com>. As the Motorola USB serial ports have an interrupt endpoint as shown with lsusb -v, we should use option.c instead of qcaux.c as pointed out by Johan Hovold <johan@kernel.org>. The ff/ff/ff interfaces seem to always be UARTs on Motorola devices. For the other interfaces, class 0x0a (CDC Data) should not in general be added as they are typically part of a multi-interface function as noted earlier by Bjørn Mork <bjorn@mork.no>. However, looking at the Motorola mapphone kernel code, the mdm6600 0x0a class is only used for flashing the modem firmware, and there are no other interfaces. So I've added that too with more details below as it works just fine. The ttyUSB ports on Droid 4 are: ttyUSB0 DIAG, CQDM-capable ttyUSB1 MUX or NMEA, no response ttyUSB2 MUX or NMEA, no response ttyUSB3 TCMD ttyUSB4 AT-capable The ttyUSB0 is detected as QCDM capable by ModemManager. I think it's only used for debugging with ModemManager --debug for sending custom AT commands though. ModemManager already can manage data connection using the USB QMI ports that are already handled by the qmi_wwan.c driver. To enable the MUX or NMEA ports, it seems that something needs to be done additionally to enable them, maybe via the DIAG or TCMD port. It might be just a NVRAM setting somewhere, but I have no idea what NVRAM settings may need changing for that. The TCMD port seems to be a Motorola custom protocol for testing the modem and to configure it's NVRAM and seems to work just fine based on a quick test with a minimal tcmdrw tool I wrote. The voice modem AT-capable port seems to provide only partial support, and no PM support compared to the TS 27.010 based UART wired directly to the modem. The UARTs added with this change are the same product IDs as the Motorola Mapphone Android Linux kernel mdm6600_id_table. I don't have any mdm9600 based devices, so I have only tested these on mdm6600 based droid 4. Then for the class 0x0a (CDC Data) mode, the Motorola Mapphone Android Linux kernel driver moto_flashqsc.c just seems to change the port->bulk_out_size to 8K from the default. And is only used for flashing the modem firmware it seems. I've verified that flashing the modem with signed firmware works just fine with the option driver after manually toggling the GPIO pins, so I've added droid 4 modem flashing mode to the option driver. I've not added the other devices listed in moto_flashqsc.c in case they really need different port->bulk_out_size. Those can be added as they get tested to work for flashing the modem. After this patch the output of /sys/kernel/debug/usb/devices has the following for normal 22b8:2a70 mode including the related qmi_wwan interfaces: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=22b8 ProdID=2a70 Rev= 0.00 S: Manufacturer=Motorola, Incorporated S: Product=Flash MZ600 C:* #Ifs= 9 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=84(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=86(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=88(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=8a(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=07(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 7 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan E: Ad=8b(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=8c(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=08(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan E: Ad=8d(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=8e(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=09(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms In 22b8:900e "qc_dload" mode the device shows up as: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=22b8 ProdID=900e Rev= 0.00 S: Manufacturer=Motorola, Incorporated S: Product=Flash MZ600 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms And in 22b8:4281 "ram_downloader" mode the device shows up as: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=22b8 ProdID=4281 Rev= 0.00 S: Manufacturer=Motorola, Incorporated S: Product=Flash MZ600 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=fc Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms Cc: Bjørn Mork <bjorn@mork.no> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Lars Melin <larsm17@gmail.com> Cc: Marcel Partap <mpartap@gmx.net> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Michael Scott <hashcode0f@gmail.com> Cc: NeKit <nekit1000@gmail.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: Sebastian Reichel <sre@kernel.org> Tested-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-08-05USB: serial: option: add D-Link DWM-222 device IDRogan Dawes
Add device id for D-Link DWM-222 A2. MI_00 D-Link HS-USB Diagnostics MI_01 D-Link HS-USB Modem MI_02 D-Link HS-USB AT Port MI_03 D-Link HS-USB NMEA MI_04 D-Link HS-USB WWAN Adapter (qmi_wwan) MI_05 USB Mass Storage Device Cc: stable@vger.kernel.org Signed-off-by: Rogan Dawes <rogan@dawes.za.net> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-08-05USB: serial: option: Add support for ZTE MF871AYoshiaki Okamoto
This patch adds support for MF871A USB modem (aka Speed USB STICK U03) to option driver. This modem is manufactured by ZTE corporation, and sold by KDDI. Interface layout: 0: AT 1: MODEM usb-devices output: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 9 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=19d2 ProdID=1481 Rev=52.87 S: Manufacturer=ZTE,Incorporated S: Product=ZTE Technologies MSM S: SerialNumber=1234567890ABCDEF C: #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option Co-developed-by: Hiroyuki Yamamoto <hyamamo@allied-telesis.co.jp> Signed-off-by: Hiroyuki Yamamoto <hyamamo@allied-telesis.co.jp> Signed-off-by: Yoshiaki Okamoto <yokamoto@allied-telesis.co.jp> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-07-03Merge tag 'usb-serial-5.3-rc1' of ↵Greg Kroah-Hartman
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next Johan writes: USB-serial updates for 5.3-rc1 Here are the USB-serial updates for 5.3-rc1; just some new device ids this time. All have been in linux-next with no reported issues. Signed-off-by: Johan Hovold <johan@kernel.org> * tag 'usb-serial-5.3-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: USB: serial: ftdi_sio: add ID for isodebug v1 USB: serial: option: add support for GosunCn ME3630 RNDIS mode
2019-06-28USB: serial: ftdi_sio: add ID for isodebug v1Andreas Fritiofson
This adds the vid:pid of the isodebug v1 isolated JTAG/SWD+UART. Only the second channel is available for use as a serial port. Signed-off-by: Andreas Fritiofson <andreas.fritiofson@unjo.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-06-20docs: usb: rename files to .rst and add them to drivers-apiMauro Carvalho Chehab
While there are a mix of things here, most of the stuff were written from Kernel developer's PoV. So, add them to the driver-api book. A follow up for this patch would be to move documents from there that are specific to sysadmins, adding them to the admin-guide. Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Acked-by: Johan Hovold <johan@kernel.org> Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-19USB: serial: option: add support for GosunCn ME3630 RNDIS modeJörgen Storvist
Added USB IDs for GosunCn ME3630 cellular module in RNDIS mode. T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=03 Dev#= 18 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=19d2 ProdID=0601 Rev=03.18 S: Manufacturer=Android S: Product=Android S: SerialNumber=b950269c C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 1 Cls=e0(wlcon) Sub=01 Prot=03 Driver=rndis_host I: If#=0x1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-05-21USB: serial: option: add Telit 0x1260 and 0x1261 compositionsDaniele Palmas
Added support for Telit LE910Cx 0x1260 and 0x1261 compositions. Signed-off-by: Daniele Palmas <dnlplm@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-05-21USB: serial: pl2303: add Allied Telesis VT-Kit3Chris Packham
This is adds the vendor and device id for the AT-VT-Kit3 which is a pl2303-based device. Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-05-21USB: serial: option: add support for Simcom SIM7500/SIM7600 RNDIS modeJörgen Storvist
Added IDs for Simcom SIM7500/SIM7600 series cellular module in RNDIS mode. Reserved the interface for ADB. T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 7 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1e0e ProdID=9011 Rev=03.18 S: Manufacturer=SimTech, Incorporated S: Product=SimTech, Incorporated S: SerialNumber=0123456789ABCDEF C: #Ifs= 8 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=ff Driver=rndis_host I: If#=0x1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x7 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-05-03USB: serial: f81232: implement break controlJi-Ze Hong (Peter Hong)
Implement Fintek F81232 break on/off with LCR register. It's the same with 16550A LCR register layout. Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com> [ johan: fix corrupt line settings on break due to missing shadow_lcr update in set_termios() ] Signed-off-by: Johan Hovold <johan@kernel.org>
2019-05-03USB: serial: f81232: add high baud rate supportJi-Ze Hong (Peter Hong)
The F81232 had 4 clocksource 1.846/18.46/14.77/24MHz and baud rates can be up to 1.5Mbits with 24MHz. F81232 Clock registers (106h) Bit1-0: Clock source selector 00: 1.846MHz. 01: 18.46MHz. 10: 24MHz. 11: 14.77MHz. Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-05-03USB: serial: f81232: clear overrun flagJi-Ze Hong (Peter Hong)
The F81232 will report data and LSR with bulk like following format: bulk-in data: [LSR(1Byte)+DATA(1Byte)][LSR(1Byte)+DATA(1Byte)]... LSR will auto clear frame/parity/break error flag when reading by H/W, but overrrun will only cleared when reading LSR. So this patch add a worker to read LSR when overrun and flush the worker on close() & suspend(). Cc: Oliver Neukum <oneukum@suse.com> Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-05-03USB: serial: f81232: fix interrupt worker not stopJi-Ze Hong (Peter Hong)
The F81232 will use interrupt worker to handle MSR change. This patch will fix the issue that interrupt work should stop in close() and suspend(). This also fixes line-status events being disabled after a suspend cycle until the port is re-opened. Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com> [ johan: amend commit message ] Fixes: 87fe5adcd8de ("USB: f81232: implement read IIR/MSR with endpoint") Cc: stable <stable@vger.kernel.org> # 4.1 Signed-off-by: Johan Hovold <johan@kernel.org>
2019-05-03USB: serial: io_edgeport: fix up switch fall-through commentsGreg Kroah-Hartman
Gustavo has been working to fix up all of the switch statements that "fall through" such that we can eventually turn on -Wimplicit-fallthrough. As part of that, the io_edgeport.c driver is a bit "messy" with the parsing logic of a data packet. Clean that logic up a bit by unindenting one level of the logic, and properly label /* Fall through */ to make gcc happy. Reported-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-30USB: serial: drop unnecessary gotoJohan Hovold
Drop an unnecessary goto from a write-urb completion error path. Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-30USB: serial: clean up throttle handlingJohan Hovold
Clean up the throttle implementation by dropping the redundant throttle_req flag which was a remnant from back when there was only a single read URB. Also convert the throttled flag to an atomic bit flag. Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-30USB: serial: fix unthrottle racesJohan Hovold
Fix two long-standing bugs which could potentially lead to memory corruption or leave the port throttled until it is reopened (on weakly ordered systems), respectively, when read-URB completion races with unthrottle(). First, the URB must not be marked as free before processing is complete to prevent it from being submitted by unthrottle() on another CPU. CPU 1 CPU 2 ================ ================ complete() unthrottle() process_urb(); smp_mb__before_atomic(); set_bit(i, free); if (test_and_clear_bit(i, free)) submit_urb(); Second, the URB must be marked as free before checking the throttled flag to prevent unthrottle() on another CPU from failing to observe that the URB needs to be submitted if complete() sees that the throttled flag is set. CPU 1 CPU 2 ================ ================ complete() unthrottle() set_bit(i, free); throttled = 0; smp_mb__after_atomic(); smp_mb(); if (throttled) if (test_and_clear_bit(i, free)) return; submit_urb(); Note that test_and_clear_bit() only implies barriers when the test is successful. To handle the case where the URB is still in use an explicit barrier needs to be added to unthrottle() for the second race condition. Fixes: d83b405383c9 ("USB: serial: add support for multiple read urbs") Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-26USB: serial: spcp8x5: simplify init_termiosJohan Hovold
Simplify init_termios which is only used to override the initial baudrate. Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-26USB: serial: oti6858: simplify init_termiosJohan Hovold
Simplify init_termios which is only used to override the initial baudrate. Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-26USB: serial: iuu_phoenix: simplify init_termiosJohan Hovold
Override the initial terminal settings provided by core directly instead of first resetting them to tty_std_termios. Also reorder the cflags as they are usually seen (in bit order). Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-26USB: serial: iuu_phoenix: drop bogus initial cflagJohan Hovold
Drop bogus TIOCM_CTS, which is not a cflag, from the initial terminal settings. Note that the corresponding bit is already set by CS8. Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-26USB: serial: cypress_m8: clean up initial-termios handlingJohan Hovold
Now that init_termios() is only called on first use, we can clean up the cypress_m8 initial-termios handling. Note that only the earthmate chip type used settings different from the defaults provided by USB serial core, and that the chip type is indeed known when init_termios is called at tty-install time. Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-26USB: serial: cypress_m8: drop unused termiosJohan Hovold
Drop driver termios structure that held a copy of the tty termios for no good reason. Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-26USB: serial: cypress_m8: drop unused driver data flagJohan Hovold
Drop the isthrottled flag which has never been used. Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-26USB: serial: ark3116: drop redundant init_termiosJohan Hovold
The initial terminal settings set by the driver matches the default settings provided by core so drop the redundant init_termios callback. Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-26USB: serial: fix initial-termios handlingJohan Hovold
The USB-serial driver init_termios callback is used to override the default initial terminal settings provided by USB-serial core. After a bug was fixed in the original implementation introduced by commit fe1ae7fdd2ee ("tty: USB serial termios bits"), the init_termios callback was no longer called just once on first use as intended but rather on every (first) open. This specifically meant that the terminal settings saved on (final) close were ignored when reopening a port for drivers overriding the initial settings. Also update the outdated function header referring to the creation of termios objects. Fixes: 7e29bb4b779f ("usb-serial: fix termios initialization logic") Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-21USB: serial: digi_acceleport: clean up set_termiosJohan Hovold
Clean up set_termios() by adding missing white space around operators and making a couple of continuation lines more readable. Also drop a couple of redundant braces. Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-21USB: serial: digi_acceleport: clean up modem-control handlingJohan Hovold
Clean up modem-control handling somewhat by adding missing whitespace around operators and splitting a long statement in two. Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-03USB: serial: pl2303: fix tranceiver suspend modeJohan Hovold
Add helper function to update register bits instead of overwriting the entire control register when updating the flow-control settings. This specifically avoids having the tranceiver suspend mode (bit 0) depend on the flow control setting. The tranceiver is currently configured at probe to be disabled during suspend, but this was overridden when disabling flow control or enabling xon/xoff. Fixes: 715f9527c1c1 ("USB: flow control fix for pl2303") Fixes: 7041d9c3f01b ("USB: serial: pl2303: add support for tx xon/xoff flow control") Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-03USB: serial: pl2303: fix non-supported xon/xoffJohan Hovold
Older pl2303 devices do not support automatic xon/xoff flow control, so add add a flag to prevent trying to enable it for legacy device types. Refactor the IXON test into a helper function to improve readability. Fixes: 7041d9c3f01b ("USB: serial: pl2303: add support for tx xon/xoff flow control") Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-03-28USB: serial: option: add Olicard 600Bjørn Mork
This is a Qualcomm based device with a QMI function on interface 4. It is mode switched from 2020:2030 using a standard eject message. T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2020 ProdID=2031 Rev= 2.32 S: Manufacturer=Mobile Connect S: Product=Mobile Connect S: SerialNumber=0123456789ABCDEF C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none) E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us Cc: stable@vger.kernel.org Signed-off-by: Bjørn Mork <bjorn@mork.no> [ johan: use tabs to align comments in adjacent lines ] Signed-off-by: Johan Hovold <johan@kernel.org>
2019-03-28USB: serial: cp210x: add new device idGreg Kroah-Hartman
Lorenz Messtechnik has a device that is controlled by the cp210x driver, so add the device id to the driver. The device id was provided by Silicon-Labs for the devices from this vendor. Reported-by: Uli <t9cpu@web.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-03-20USB: serial: mos7720: fix mos_parport refcount imbalance on error pathLin Yi
The write_parport_reg_nonblock() helper takes a reference to the struct mos_parport, but failed to release it in a couple of error paths after allocation failures, leading to a memory leak. Johan said that move the kref_get() and mos_parport assignment to the end of urbtrack initialisation is a better way, so move it. and mos_parport do not used until urbtrack initialisation. Signed-off-by: Lin Yi <teroincn@163.com> Fixes: b69578df7e98 ("USB: usbserial: mos7720: add support for parallel port on moschip 7715") Cc: stable <stable@vger.kernel.org> # 2.6.35 Signed-off-by: Johan Hovold <johan@kernel.org>
2019-03-19USB: serial: option: set driver_info for SIM5218 and compatiblesMans Rullgard
The SIMCom SIM5218 and compatible devices have 5 USB interfaces, only 4 of which are serial ports. The fifth is a network interface supported by the qmi-wwan driver. Furthermore, the serial ports do not support modem control signals. Add driver_info flags to reflect this. Signed-off-by: Mans Rullgard <mans@mansr.com> Fixes: ec0cd94d881c ("usb: option: add SIMCom SIM5218") Cc: stable <stable@vger.kernel.org> # 3.2 Signed-off-by: Johan Hovold <johan@kernel.org>
2019-03-19USB: serial: ftdi_sio: add additional NovaTech productsGeorge McCollister
Add PIDs for the NovaTech OrionLX+ and Orion I/O so they can be automatically detected. Signed-off-by: George McCollister <george.mccollister@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-03-19USB: serial: option: add support for Quectel EM12Kristian Evensen
The Quectel EM12 is a Cat. 12 LTE modem. It behaves in the exactly the same way as the EP06 (including the dynamic configuration behavior), so the same checks on reserved interfaces, etc. are needed. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-02-21Merge tag 'usb-serial-5.1-rc1-2' of ↵Greg Kroah-Hartman
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next Johan writes: USB-serial fixes for 5.1-rc1 Here are a couple of new device ids for 5.1-rc1. All have been in linux-next with no reported issues. Signed-off-by: Johan Hovold <johan@kernel.org> * tag 'usb-serial-5.1-rc1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: USB: serial: ftdi_sio: add ID for Hjelmslund Electronics USB485 USB: serial: cp210x: add ID for Ingenico 3070
2019-02-21Merge tag 'usb-serial-5.1-rc1' of ↵Greg Kroah-Hartman
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next Johan writes: USB-serial updates for 5.1-rc1 Here are the USB-serial updates for 5.1-rc1, including: - support for the last three GPIOs on cp2102n devices - gpio support for cp2104 - support for using cp210x gpios with autosuspend - proper error handling for unsupported cp2105 line speeds Included is also a new modem device id. All have been in linux-next with no reported issues. Signed-off-by: Johan Hovold <johan@kernel.org> * tag 'usb-serial-5.1-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: USB: serial: option: add Telit ME910 ECM composition USB: serial: cp210x: fix GPIO in autosuspend USB: serial: cp210x: add minimum baud rate for CP2105 SCI USB: serial: cp210x: add GPIO support for CP2104 USB: serial: cp210x: support all gpios on CP2102N QFN28 package
2019-02-20USB: serial: option: add Telit ME910 ECM compositionDaniele Palmas
This patch adds Telit ME910 family ECM composition 0x1102. Signed-off-by: Daniele Palmas <dnlplm@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-02-20USB: serial: cp210x: fix GPIO in autosuspendKaroly Pados
Current GPIO code in cp210x fails to take USB autosuspend into account, making it practically impossible to use GPIOs with autosuspend enabled without user configuration. Fix this like for ftdi_sio in a previous patch. Tested on a CP2102N. Signed-off-by: Karoly Pados <pados@pados.hu> Fixes: cf5276ce7867 ("USB: serial: cp210x: Adding GPIO support for CP2105") Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-02-15USB: serial: ftdi_sio: add ID for Hjelmslund Electronics USB485Mans Rullgard
This adds the USB ID of the Hjelmslund Electronics USB485 Iso stick. Signed-off-by: Mans Rullgard <mans@mansr.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-02-07USB: serial: cp210x: add ID for Ingenico 3070Ivan Mironov
Here is how this device appears in kernel log: usb 3-1: new full-speed USB device number 18 using xhci_hcd usb 3-1: New USB device found, idVendor=0b00, idProduct=3070 usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 3-1: Product: Ingenico 3070 usb 3-1: Manufacturer: Silicon Labs usb 3-1: SerialNumber: 0001 Apparently this is a POS terminal with embedded USB-to-Serial converter. Cc: stable@vger.kernel.org Signed-off-by: Ivan Mironov <mironov.ivan@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-02-07USB: serial: cp210x: add minimum baud rate for CP2105 SCIJohanna Abrahamsson
Add minimum baud rate to the cp210x driver. According to the datasheet for CP2105, the SCI supports 2400 as the lowest baud rate. As this is not heeded in the current code, an error message 'failed set req 0x1e size 4 status: -32' when trying to set a lower baud rate such as 300. The other cp210x models to date supports a minimum baud rate of 300. Signed-off-by: Johanna Abrahamsson <johanna.abrahamsson@afconsult.com> [ johan: simplify min_speed init, move clamp after comment, and drop unused serial-data pointer from cp210x_get_actual_rate() ] Signed-off-by: Johan Hovold <johan@kernel.org>
2019-02-04USB: serial: cp210x: add GPIO support for CP2104Icenowy Zheng
The CP2104 chips feature 4 controllable GPIO pins, which are similar to the ones on CP2102N chip (output-only when push-pull, output or simulated input mode when open-drain). Add support for the GPIO pins for cp210x driver. The pin get/set routine is shared with CP2102N, but the pinconf initialization code is not shared because the acquisition of GPIO configuration in OTP ROM is similar to CP2105, not CP2102N. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-01-28Merge 5.0-rc4 into usb-nextGreg Kroah-Hartman
We need the USB fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-25USB: serial: cp210x: support all gpios on CP2102N QFN28 packageMans Rullgard
The QFN28 package version of the CP2102N has three additional gpio pins. Add support for these. Signed-off-by: Mans Rullgard <mans@mansr.com> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-01-22USB: add missing SPDX lines to Kconfig and MakefilesGreg Kroah-Hartman
There are a few remaining drivers/usb/ files that do not have SPDX identifiers in them, all of these are either Kconfig or Makefiles. Add the correct GPL-2.0 identifier to them to make scanning tools happy. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit (git 2.34.1) at 2024-05-29 18:57:29 +0000