| Age | Commit message (Collapse) | Author |
|---|
|
We shouldn't have any glue layer which doesn't
compile everywhere. In order to make sure this is
always the case, make sure COMPILE_TEST is properly
added at dependency list of a config entry.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
We don't need dwc3_trace() unless we're building a
kernel with CONFIG_FTRACE. This patch reduces
dwc3.ko text size a bit while also removing overhead
of dwc3_trace() calls.
text data bss dec hex filename
50796 581 0 51377 c8b1 drivers/usb/dwc3/dwc3.o
43961 581 0 44542 adfe drivers/usb/dwc3/dwc3.o.patched
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
We can offset the latency of a full Start Transfer
command - where we _must_ poll for its completion -
to usb_ep_enable() time. This means that once
requests start showing up from the gadget driver, we
can rely on No Response Update Transfer command -
where we don't need to poll for completion.
This patch, starts implementing this method for Bulk
endpoints, even though, technically, we could extend
it to all other endpoints in future commits.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
In case of periodic transfers, let's pretty print
the size field as a multiplier followed by length,
such as :
3x 1024
instead of:
33555456
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Cc: Li Yang <leoli@freescale.com>
Cc: <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Cc: Ashwini Pahuja <ashwini.linux@gmail.com>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove this macro
from the driver.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <linux-usb@vger.kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Cc: Peter Chen <Peter.Chen@nxp.com>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
usb_endpoint_maxp() is now returning maxpacket
correctly - iow only bits 10:0. We can finaly remove
XHCI's private GET_MAX_PACKET macro.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Cc: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Cc: Li Yang <leoli@freescale.com>
Cc: <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Cc: Ashwini Pahuja <ashwini.linux@gmail.com>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <linux-usb@vger.kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Acked-by: Peter Chen <Peter.Chen@nxp.com>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
With this extra piece of information, it will be
easier to find mismatches between driver and HW.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
We will be using dwc3_ep0_state_string() from within
our tracepoints, so we need to move that helper to
debug.h in order for it to be accessible.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Removing some trace prints which were made redundant
when we started decoding events and TRBs completely
within their respective trace points.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
DWC3 can tell us which phase of a setup transfer
we're getting into. Let's decode it from the event
to make it easier to debug.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Link State Change events are only needed for
debugging and to apply certain workarounds on known
errata. Let's save a few cycles by disabling these
events completely on working revisions of the core.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
There might be situations where a Start Transfer
command might fail, if that ever happens, instead of
simply removing the request from our list, we should
give the request back to the gadget driver,
otherwise we might eventually starve it from requests.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
No Response Update Transfer is a special type of
Update Transfer command which can be used whenever
we're not relying on XferNotReady to prepare
transfers. With this, we don't need to wait for
CMDACT to be cleared and issue further commands to
the endpoint straight away.
Let's start using this version to skip the long-ish
wait.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The cmd argument we pass to
dwc3_send_gadget_ep_cmd() could contain extra
arguments embedded. When checking for StartTransfer
command, we need to make sure to match only lower 4
bits which contain the actual command and ignore the
rest.
Reported-by: Janusz Dziedzic <januszx.dziedzic@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
In case of High-Speed, High-Bandwidth endpoints, we
need to tell DWC3 that we have more than one packet
per interval. We do that by setting PCM1 field of
Isochronous-First TRB.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
ep->mult is supposed to be set to Isochronous and
Interrupt Endapoint's multiplier value. This value
is computed from different places depending on the
link speed.
If we're dealing with HighSpeed, then it's part of
bits [12:11] of wMaxPacketSize. This case wasn't
taken into consideration before.
While at that, also make sure the ep->mult defaults
to one so drivers can use it unconditionally and
assume they'll never multiply ep->maxpacket to zero.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
usb_endpoint_maxp() returns wMaxPacketSize in its
raw form. Without taking into consideration that it
also contains other bits reserved for isochronous
endpoints.
This patch fixes one occasion where this is a
problem by making sure that we initialize
ep->maxpacket only with lower 10 bits of the value
returned by usb_endpoint_maxp(). Note that seperate
patches will be necessary to audit all call sites of
usb_endpoint_maxp() and make sure that
usb_endpoint_maxp() only returns lower 10 bits of
wMaxPacketSize.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
After commit b09b5224fe86 ("usb: chipidea: implement platform shutdown
callback") and commit 43a404577a93 ("usb: chipidea: host: set host to
be null after hcd is freed") a NULL pointer dereference is caused
on i.MX23 during shutdown. So ensure that role is set to CI_ROLE_END and
we finish interrupt handling before the hcd is deallocated. This avoids
the NULL pointer dereference.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: b09b5224fe86 ("usb: chipidea: implement platform shutdown callback")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
Since the controller on R-Car Gen3 doesn't have any status registers
to detect initialization (LPSTS.SUSPM = 1) and the initialization needs
up to 45 usec, this patch adds wait after the initialization. Otherwise,
writing other registers (e.g. INTENB0) will fail.
Fixes: de18757e272d ("usb: renesas_usbhs: add R-Car Gen3 power control")
Cc: <stable@vger.kernel.org> # v4.6+
Cc: <balbi@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Increase ohci watchout delay to 275 ms. Previous delay was 250 ms
with 20 ms of slack, after removing slack time some ohci controllers don't
respond in time. Logs from systems with controllers that have the
issue would show "HcDoneHead not written back; disabled"
Signed-off-by: Bryan Paluch <bryanpaluch@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If we're booting pandaboard using NFSroot over built-in g_ether, we
can get the following after booting once and doing a warm reset:
g_ether gadget: ecm_open
g_ether gadget: notify connect true
...
WARNING: CPU: 0 PID: 1 at drivers/bus/omap_l3_noc.c:147
l3_interrupt_handler+0x220/0x34c
44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4CFG (Read):
Data Access in User mode du ring Functional access
...
Fix the issue by calling pm_runtime functions from
musb_gadget_queue.
Note that in the long run we should be able to queue the pending
transfers if pm_runtime is not active, and flush the queue from
pm_runtime_resume.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If we configure musb with 2430 glue as a peripheral, and then rmmod
omap2430 module, we'll get the following error:
[ INFO: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected ]
...
rmmod/413 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
(&phy->mutex){+.+.+.}, at: [<c04b9fd0>] phy_power_off+0x1c/0xb8
[ 204.678710]
and this task is already holding:
(&(&musb->lock)->rlock){-.-...}, at: [<bf3a482c>]
musb_gadget_stop+0x24/0xec [musb_hdrc]
which would create a new lock dependency:
(&(&musb->lock)->rlock){-.-...} -> (&phy->mutex){+.+.+.}
...
This is because some glue layers expect musb_platform_enable/disable
to be called with spinlock held, and 2430 glue layer has USB PHY on
the I2C bus using a mutex.
We could fix the glue layers to take the spinlock, but we still have
a problem of musb_plaform_enable/disable being called in an unbalanced
manner. So that would still lead into USB PHY enable/disable related
problems for omap2430 glue layer.
While it makes sense to only enable USB PHY when needed from PM point
of view, in this case we just can't do it yet without breaking things.
So let's just revert phy_enable/disable related changes instead and
reconsider this after we have fixed musb_platform_enable/disable to
be balanced.
Fixes: a83e17d0f73b ("usb: musb: Improve PM runtime and phy handling for 2430 glue layer")
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Socionext LD11 SoC (arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi)
needs to handle 4 reset lines for EHCI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
