| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
|
|
Conflicts:
include/linux/compiler-clang.h
include/linux/compiler-gcc.h
include/linux/compiler-intel.h
include/uapi/linux/stddef.h
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Also adds missing call to
destroy_timer_on_stack();
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: "Gustavo A. R. Silva" <garsilva@embeddedor.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
to READ_ONCE()/WRITE_ONCE()
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
If the connect status change is set during reset signaling, but
the status remains connected just retry port reset.
This solves an issue with connecting a 90W HP Thunderbolt 3 dock
with a Lenovo Carbon x1 (5th generation) which causes a 30min loop
of a high speed device being re-discovererd before usb ports starts
working.
[...]
[ 389.023845] usb 3-1: new high-speed USB device number 55 using xhci_hcd
[ 389.491841] usb 3-1: new high-speed USB device number 56 using xhci_hcd
[ 389.959928] usb 3-1: new high-speed USB device number 57 using xhci_hcd
[...]
This is caused by a high speed device that doesn't successfully go to the
enabled state after the second port reset. Instead the connection bounces
(connected, with connect status change), bailing out completely from
enumeration just to restart from scratch.
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1716332
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.14-rc6
Here's a new metro-usb device id for another bar-code scanner.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Andrey used the syzkaller fuzzer to find an out-of-bounds memory
access in usb_get_bos_descriptor(). The code wasn't checking that the
next usb_dev_cap_header structure could fit into the remaining buffer
space.
This patch fixes the error and also reduces the bNumDeviceCaps field
in the header to match the actual number of capabilities found, in
cases where there are fewer than expected.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This keyboard doesn't implement Get String descriptors properly even
though string indexes are valid. What happens is that when requesting
for the String descriptor, the device disconnects and
reconnects. Without this quirk, this loop will continue forever.
Cc: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Владимир Мартьянов <vilgeforce@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This fixes a kernel oops when unloading the driver due to usb_put_phy
being called after usb_phy_generic_unregister when the device is
detached. Calling usb_phy_generic_unregister causes x->dev->driver to
be NULL in usb_put_phy and results in a NULL pointer dereference.
Cc: stable@vger.kernel.org # v4.3+
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The sunxi musb has a bug where sometimes it will generate a babble
error on device disconnect instead of a disconnect IRQ. When this
happens the musb controller switches from host mode to device mode
(it clears MUSB_DEVCTL_HM/MUSB_DEVCTL_SESSION and sets
MUSB_DEVCTL_BDEVICE) and gets stuck in this state.
The babble error is misdetected as a bus reset because MUSB_DEVCTL_HM
was cleared.
To fix this, use is_host_active() rather than (devctl & MUSB_DEVCTL_HM)
to detect babble error so that sunxi musb babble recovery can handle it
by restoring the mode. This information is provided by the driver logic
and does not rely on register contents.
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, the number of channels is set to 15 but in the case of DA8xx,
the number of channels is 4.
Update the driver to configure the number of channels at runtime.
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The way to configure the DMA mode on DA8xx is different from DSPS.
Add a new function to configure DMA mode on DA8xx and use a callback
to call the right function based on the platform.
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The DA8xx and DSPS platforms don't use the same address for few registers.
On Da8xx, this is causing some issues (e.g. teardown that doesn't work).
Configure the address of the register during the init and use them instead
of constants.
Cc: stable@vger.kernel.org # v4.12+
Reported-by: nsekhar@ti.com
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The musb delayed irq work was never flushed on suspend, something which
since 4.9 can lead to an external abort if the work is scheduled after
the grandparent's clock has been disabled:
PM: Suspending system (mem)
PM: suspend of devices complete after 125.224 msecs
PM: suspend devices took 0.132 seconds
PM: late suspend of devices complete after 7.423 msecs
PM: noirq suspend of devices complete after 7.083 msecs
suspend debug: Waiting for 5 second(s).
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd0262c60
...
[<c054880c>] (musb_default_readb) from [<c0547b5c>] (musb_irq_work+0x48/0x220)
[<c0547b5c>] (musb_irq_work) from [<c014f8a4>] (process_one_work+0x1f4/0x758)
[<c014f8a4>] (process_one_work) from [<c014fe5c>] (worker_thread+0x54/0x514)
[<c014fe5c>] (worker_thread) from [<c015704c>] (kthread+0x128/0x158)
[<c015704c>] (kthread) from [<c0109330>] (ret_from_fork+0x14/0x24)
Commit 2bff3916fda9 ("usb: musb: Fix PM for hub disconnect") started
scheduling musb_irq_work with a delay of up to a second and with
retries thereby making this easy to trigger, for example, by suspending
shortly after a disconnect.
Note that we set a flag to prevent the irq work from rescheduling itself
during suspend and instead process a disconnect immediately. This takes
care of the case where we are disconnected shortly before suspending.
However, when in host mode, a disconnect while suspended will still
go unnoticed and thus prevent the controller from runtime suspending
upon resume as the session bit is always set. This will need to be
addressed separately.
Fixes: 550a7375fe72 ("USB: Add MUSB and TUSB support")
Fixes: 467d5c980709 ("usb: musb: Implement session bit based runtime PM for musb-core")
Fixes: 2bff3916fda9 ("usb: musb: Fix PM for hub disconnect")
Cc: stable <stable@vger.kernel.org> # 4.9
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current session-bit quirk implementation does not prevent the retry
counter from underflowing, something which could break runtime PM and
keep the device active for a very long time (about 2^32 seconds) after a
disconnect.
This notably breaks the B-device timeout case, but could potentially
cause problems also when the controller is operating as an A-device.
Fixes: 2bff3916fda9 ("usb: musb: Fix PM for hub disconnect")
Cc: stable <stable@vger.kernel.org> # 4.9
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Elatec TWN3 has the union descriptor on data interface. This results in
failure to bind the device to the driver with the following log:
usb 1-1.2: new full speed USB device using streamplug-ehci and address 4
usb 1-1.2: New USB device found, idVendor=09d8, idProduct=0320
usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1.2: Product: RFID Device (COM)
usb 1-1.2: Manufacturer: OEM
cdc_acm 1-1.2:1.0: Zero length descriptor references
cdc_acm: probe of 1-1.2:1.0 failed with error -22
Adding the NO_UNION_NORMAL quirk for the device fixes the issue.
`lsusb -v` of the device:
Bus 001 Device 003: ID 09d8:0320
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 32
idVendor 0x09d8
idProduct 0x0320
bcdDevice 3.00
iManufacturer 1 OEM
iProduct 2 RFID Device (COM)
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 67
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 250mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 1 AT-commands (v.25ter)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 2
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 0
CDC Header:
bcdCDC 1.10
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
CDC ACM:
bmCapabilities 0x06
sends break
line coding and serial state
CDC Union:
bMasterInterface 0
bSlaveInterface 1
Device Status: 0x0000
(Bus Powered)
Signed-off-by: Maksim Salau <msalau@iotecha.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Taking the uurb->buffer_length userspace passes in as a maximum for the
actual urbs transfer_buffer_length causes 2 serious issues:
1) It breaks isochronous support for all userspace apps using libusb,
as existing libusb versions pass in 0 for uurb->buffer_length,
relying on the kernel using the lenghts of the usbdevfs_iso_packet_desc
descriptors passed in added together as buffer length.
This for example causes redirection of USB audio and Webcam's into
virtual machines using qemu-kvm to no longer work. This is a userspace
ABI break and as such must be reverted.
Note that the original commit does not protect other users / the
kernels memory, it only stops the userspace process making the call
from shooting itself in the foot.
2) It may cause the kernel to program host controllers to DMA over random
memory. Just as the devio code used to only look at the iso_packet_desc
lenghts, the host drivers do the same, relying on the submitter of the
urbs to make sure the entire buffer is large enough and not checking
transfer_buffer_length.
But the "USB: devio: Don't corrupt user memory" commit now takes the
userspace provided uurb->buffer_length for the buffer-size while copying
over the user-provided iso_packet_desc lengths 1:1, allowing the user
to specify a small buffer size while programming the host controller to
dma a lot more data.
(Atleast the ohci, uhci, xhci and fhci drivers do not check
transfer_buffer_length for isoc transfers.)
This reverts commit fa1ed74eb1c2 ("USB: devio: Don't corrupt user memory")
fixing both these issues.
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xhci_stop_device() calls xhci_queue_stop_endpoint() multiple times
without checking the return value. xhci_queue_stop_endpoint() can
return error if the HC is already halted or unable to queue commands.
This can cause a deadlock condition as xhci_stop_device() would
end up waiting indefinitely for a completion for the command that
didn't get queued. Fix this by checking the return value and bailing
out of xhci_stop_device() in case of error. This patch happens to fix
potential memory leaks of the allocated command structures as well.
Fixes: c311e391a7ef ("xhci: rework command timeout and cancellation,")
Cc: <stable@vger.kernel.org>
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When a URB is cancled, xhci driver turns the untransferred trbs
into no-ops. If an endpoint stalls on a no-op trb that belongs
to the cancelled URB, the event handler won't reset the endpoint.
Hence, it will stay halted.
Link: http://marc.info/?l=linux-usb&m=149582598330127&w=2
Cc: <stable@vger.kernel.org>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
KASAN reported use-after-free bug when xhci host controller died:
[ 176.952537] BUG: KASAN: use-after-free in xhci_handle_command_timeout+0x68/0x224
[ 176.960846] Write of size 4 at addr ffffffc0cbb01608 by task kworker/3:3/1680
...
[ 177.180644] Freed by task 0:
[ 177.183882] kasan_slab_free+0x90/0x15c
[ 177.188194] kfree+0x114/0x28c
[ 177.191630] xhci_cleanup_command_queue+0xc8/0xf8
[ 177.196916] xhci_hc_died+0x84/0x358
Problem here is that when the cmd_timer fired, it would try to access
current_cmd while the command queue is already freed by xhci_hc_died().
Cleanup current_cmd in xhci_cleanup_command_queue() to avoid that.
Fixes: d9f11ba9f107 ("xhci: Rework how we handle unresponsive or hoptlug removed hosts")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Many USB 3.1 capable hosts never updated the Serial Bus Release Number
(SBRN) register to USB 3.1 from USB 3.0
xhci driver identified USB 3.1 capable hosts based on this SBRN register,
which according to specs "contains the release of the Universal Serial
Bus Specification with which this Universal Serial Bus Host Controller
module is compliant." but still in october 2017 gives USB 3.0 as
the only possible option.
Make an additional check for USB 3.1 support and enable it if the xHCI
supported protocol capablity lists USB 3.1 capable ports.
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add device-id entry for (Honeywell) Metrologic MS7820 bar code scanner.
The device has two interfaces (in this mode?); a vendor-specific
interface with two interrupt endpoints and a second HID interface, which
we do not bind to.
Reported-by: Ladislav Dobrovsky <ladislav.dobrovsky@gmail.com>
Tested-by: Ladislav Dobrovsky <ladislav.dobrovsky@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
USB: fixes for v4.14-rc5
A deadlock fix in dummy-hcd; Fixing a use-after-free bug in composite;
Renesas got another fix for DMA programming (this time around a fix
for receiving ZLP); Tegra PHY got a suspend fix; A memory leak on our
configfs ABI got plugged.
Other than these, a couple other minor fixes on usbtest.
|
|
If the usbtest driver encounters a device with an IN bulk endpoint but
no OUT bulk endpoint, it will try to dereference a NULL pointer
(out->desc.bEndpointAddress). The problem can be solved by adding a
missing test.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Kmemleak checking configuration reports a memory leak in
usb_os_desc_prepare_interf_dir function when rndis function
instance is freed and then allocated again. For example, this
happens with FunctionFS driver with RNDIS function enabled
when "ffs-test" test application is run several times in a row.
The data for intermediate "os_desc" group for interface directories
is allocated as a single VLA chunk and (after a change of default
groups handling) is not ever freed and actually not stored anywhere
besides inside a list of default groups of a parent group.
The fix is to make usb_os_desc_prepare_interf_dir function return
a pointer to allocated data (as a pointer to the first VLA item)
instead of (an unused) integer and to make the caller component
(currently the only one is RNDIS function) responsible for storing
the pointer and freeing the memory when appropriate.
Fixes: 1ae1602de028 ("configfs: switch ->default groups to a linked list")
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
KASAN enabled configuration reports an error
BUG: KASAN: use-after-free in usb_composite_overwrite_options+...
[libcomposite] at addr ...
Read of size 1 by task ...
when some driver is un-bound and then bound again.
For example, this happens with FunctionFS driver when "ffs-test"
test application is run several times in a row.
If the driver has empty manufacturer ID string in initial static data,
it is then replaced with generated string. After driver unbinding
the generated string is freed, but the driver data still keep that
pointer. And if the driver is then bound again, that pointer
is re-used for string emptiness check.
The fix is to clean up the driver string data upon its unbinding
to drop the pointer to freed memory.
Fixes: cc2683c318a5 ("usb: gadget: Provide a default implementation of default manufacturer string")
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
There used to be a test against "if (param->sglen > MAX_SGLEN)" but it
was removed during a refactor. It leads to an integer overflow and a
stack overflow in test_queue() if we try to create a too large urbs[]
array on the stack.
There is a second integer overflow in test_queue() as well if
"param->iterations" is too high. I don't immediately see that it's
harmful but I've added a check to prevent it and silence the static
checker warning.
Fixes: 18fc4ebdc705 ("usb: misc: usbtest: Remove timeval usage")
Acked-by: Deepa Dinamani <deepa.kernel@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The DREQE bit of the DnFIFOSEL should be set to 1 after the DE bit of
USB-DMAC on R-Car SoCs is set to 1 after the USB-DMAC received a
zero-length packet. Otherwise, a transfer completion interruption
of USB-DMAC doesn't happen. Even if the driver changes the sequence,
normal operations (transmit/receive without zero-length packet) will
not cause any side-effects. So, this patch fixes the sequence anyway.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[shimoda: revise the commit log]
Fixes: e73a9891b3a1 ("usb: renesas_usbhs: add DMAEngine support")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The dummy-hcd driver calls the gadget driver's disconnect callback
under the wrong conditions. It should invoke the callback when Vbus
power is turned off, but instead it does so when the D+ pullup is
turned off.
This can cause a deadlock in the composite core when a gadget driver
is unregistered:
[ 88.361471] ============================================
[ 88.362014] WARNING: possible recursive locking detected
[ 88.362580] 4.14.0-rc2+ #9 Not tainted
[ 88.363010] --------------------------------------------
[ 88.363561] v4l_id/526 is trying to acquire lock:
[ 88.364062] (&(&cdev->lock)->rlock){....}, at: [<ffffffffa0547e03>] composite_disconnect+0x43/0x100 [libcomposite]
[ 88.365051]
[ 88.365051] but task is already holding lock:
[ 88.365826] (&(&cdev->lock)->rlock){....}, at: [<ffffffffa0547b09>] usb_function_deactivate+0x29/0x80 [libcomposite]
[ 88.366858]
[ 88.366858] other info that might help us debug this:
[ 88.368301] Possible unsafe locking scenario:
[ 88.368301]
[ 88.369304] CPU0
[ 88.369701] ----
[ 88.370101] lock(&(&cdev->lock)->rlock);
[ 88.370623] lock(&(&cdev->lock)->rlock);
[ 88.371145]
[ 88.371145] *** DEADLOCK ***
[ 88.371145]
[ 88.372211] May be due to missing lock nesting notation
[ 88.372211]
[ 88.373191] 2 locks held by v4l_id/526:
[ 88.373715] #0: (&(&cdev->lock)->rlock){....}, at: [<ffffffffa0547b09>] usb_function_deactivate+0x29/0x80 [libcomposite]
[ 88.374814] #1: (&(&dum_hcd->dum->lock)->rlock){....}, at: [<ffffffffa05bd48d>] dummy_pullup+0x7d/0xf0 [dummy_hcd]
[ 88.376289]
[ 88.376289] stack backtrace:
[ 88.377726] CPU: 0 PID: 526 Comm: v4l_id Not tainted 4.14.0-rc2+ #9
[ 88.378557] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
[ 88.379504] Call Trace:
[ 88.380019] dump_stack+0x86/0xc7
[ 88.380605] __lock_acquire+0x841/0x1120
[ 88.381252] lock_acquire+0xd5/0x1c0
[ 88.381865] ? composite_disconnect+0x43/0x100 [libcomposite]
[ 88.382668] _raw_spin_lock_irqsave+0x40/0x54
[ 88.383357] ? composite_disconnect+0x43/0x100 [libcomposite]
[ 88.384290] composite_disconnect+0x43/0x100 [libcomposite]
[ 88.385490] set_link_state+0x2d4/0x3c0 [dummy_hcd]
[ 88.386436] dummy_pullup+0xa7/0xf0 [dummy_hcd]
[ 88.387195] usb_gadget_disconnect+0xd8/0x160 [udc_core]
[ 88.387990] usb_gadget_deactivate+0xd3/0x160 [udc_core]
[ 88.388793] usb_function_deactivate+0x64/0x80 [libcomposite]
[ 88.389628] uvc_function_disconnect+0x1e/0x40 [usb_f_uvc]
This patch changes the code to test the port-power status bit rather
than the port-connect status bit when deciding whether to isue the
callback.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: David Tulloh <david@tulloh.id.au>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Commit dfebb5f43a78 ("usb: chipidea: Add support for Tegra20/30/114/124")
added UDC support for Tegra but with UDC support enabled, is was found
that Tegra30, Tegra114 and Tegra124 would hang on entry to suspend.
The hang occurred during the suspend of the USB PHY when the Tegra PHY
driver attempted to disable the PHY clock. The problem is that before
the Tegra PHY driver is suspended, the chipidea driver already disabled
the PHY clock and when the Tegra PHY driver suspended, it could not read
DEVLC register and caused the device to hang.
The Tegra USB PHY driver is used by both the Tegra EHCI driver and now
the chipidea UDC driver and so simply removing the disabling of the PHY
clock from the USB PHY driver would not work for the Tegra EHCI driver.
Fortunately, the status of the USB PHY clock can be read from the
USB_SUSP_CTRL register and therefore, to workaround this issue, simply
poll the register prior to disabling the clock in USB PHY driver to see
if clock gating has already been initiated. Please note that it can take
a few uS for the clock to disable and so simply reading this status
register once on entry is not sufficient.
Similarly when turning on the PHY clock, it is possible that the clock
is already enabled or in the process of being enabled, and so check for
this when enabling the PHY.
Please note that no issues are seen with Tegra20 because it has a slightly
different PHY to Tegra30/114/124.
Fixes: dfebb5f43a78 ("usb: chipidea: Add support for Tegra20/30/114/124")
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.14-rc5
Here's a fix for a cp210x regression that prevented a class of devices
from being successfully probed. Two use-after-free bugs in the console
code are also fixed.
Included are also some new device ids.
All but the last three commits have been in linux-next with no reported
issues.
|
|
Make sure to reset the USB-console port pointer when console setup fails
in order to avoid having the struct usb_serial be prematurely freed by
the console code when the device is later disconnected.
Fixes: 73e487fdb75f ("[PATCH] USB console: fix disconnection issues")
Cc: stable <stable@vger.kernel.org> # 2.6.18
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
A clean-up patch removing two redundant NULL-checks from the console
disconnect handler inadvertently also removed a third check. This could
lead to the struct usb_serial being prematurely freed by the console
code when a driver accepts but does not register any ports for an
interface which also lacks endpoint descriptors.
Fixes: 0e517c93dc02 ("USB: serial: console: clean up sanity checks")
Cc: stable <stable@vger.kernel.org> # 4.11
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Dell Wireless 5819/5818 devices are re-branded Sierra Wireless MC74
series which will by default boot with vid 0x413c and pid's 0x81cf,
0x81d0, 0x81d1, 0x81d2.
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add compatible string to use this generic glue layer to support
Spreadtrum SC9860 platform's dwc3 controller.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The driver triggers actions on both edges of the vbus signal.
The former PIO controller was triggering IRQs on both falling and rising edges
by default. Newer PIO controller don't, so it's better to set it explicitly to
IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING.
Without this patch we may trigger the connection with host but only on some
bouncing signal conditions and thus lose connecting events.
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: stable <stable@vger.kernel.org> # v4.4+
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
By submitting completed transfers to the system workqueue there is no
guarantee that completion events will be queued up in the correct order,
as in multi-processor systems there is a thread running for each
processor and the work items are not bound to a particular core.
This means that several completions are in the queue at the same time,
they may be processed in parallel and complete out of order, resulting
in data appearing corrupt when read by userspace.
Create a single-threaded workqueue for FunctionFS so that data completed
requests is passed to userspace in the order in which they complete.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch fixes an issue that the usbhsf_fifo_clear() is possible
to cause 10 msec delay if the pipe is RX direction and empty because
the FRDY bit will never be set to 1 in such case.
Fixes: e8d548d54968 ("usb: renesas_usbhs: fifo became independent from pipe.")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch fixes an issue that the driver sets the BCLR bit of
{C,Dn}FIFOCTR register to 1 even when it's non-DCP pipe and
the FRDY bit of {C,Dn}FIFOCTR register is set to 1.
Fixes: e8d548d54968 ("usb: renesas_usbhs: fifo became independent from pipe.")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch fixes an issue that this driver cannot go status stage
in control read when the req.zero is set to 1 and the len in
usb3_write_pipe() is set to 0. Otherwise, if we use g_ncm driver,
usb enumeration takes long time (5 seconds or more).
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
According to the datasheet of R-Car Gen3, the Pn_RAMMAP.Pn_MPKT should
be set to one of 8, 16, 32, 64, 512 and 1024. Otherwise, when a gadget
driver uses an interrupt endpoint, unexpected behavior happens. So,
this patch fixes it.
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
When bRequestType & USB_DIR_IN is false and req.length is 0 in control
transfer, since it means non-data, this driver should not set the mode
as control write. So, this patch fixes it.
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
A recent change to the synchronization in dummy-hcd was incorrect.
The issue was that dummy_udc_stop() contained no locking and therefore
could race with various gadget driver callbacks, and the fix was to
add locking and issue the callbacks with the private spinlock held.
UDC drivers aren't supposed to do this. Gadget driver callback
routines are allowed to invoke functions in the UDC driver, and these
functions will generally try to acquire the private spinlock. This
would deadlock the driver.
The correct solution is to drop the spinlock before issuing callbacks,
and avoid races by emulating the synchronize_irq() call that all real
UDC drivers must perform in their ->udc_stop() routines after
disabling interrupts. This involves adding a flag to dummy-hcd's
private structure to keep track of whether interrupts are supposed to
be enabled, and adding a counter to keep track of ongoing callbacks so
that dummy_udc_stop() can wait for them all to finish.
A real UDC driver won't receive disconnect, reset, suspend, resume, or
setup events once it has disabled interrupts. dummy-hcd will receive
them but won't try to issue any gadget driver callbacks, which should
be just as good.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: f16443a034c7 ("USB: gadgetfs, dummy-hcd, net2280: fix locking for callbacks")
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The dummy-hcd HCD/UDC emulator tries not to do too much work during
each timer interrupt. But it doesn't try very hard; currently all
it does is limit the total amount of bulk data transferred. Other
transfer types aren't limited, and URBs that transfer no data (because
of an error, perhaps) don't count toward the limit, even though on a
real USB bus they would consume at least a minimum overhead.
This means it's possible to get the driver stuck in an infinite loop,
for example, if the host class driver resubmits an URB every time it
completes (which is common for interrupt URBs). Each time the URB is
resubmitted it gets added to the end of the pending-URBs list, and
dummy-hcd doesn't stop until that list is empty. Andrey Konovalov was
able to trigger this failure mode using the syzkaller fuzzer.
This patch fixes the infinite-loop problem by restricting the URBs
handled during each timer interrupt to those that were already on the
pending list when the interrupt routine started. Newly added URBs
won't be processed until the next timer interrupt. The problem of
properly accounting for non-bulk bandwidth (as well as packet and
transaction overhead) is not addressed here.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The dummy-hcd UDC driver is not careful about the way it handles
connection speeds. It ignores the module parameter that is supposed
to govern the maximum connection speed and it doesn't set the HCD
flags properly for the case where it ends up running at full speed.
The result is that in many cases, gadget enumeration over dummy-hcd
fails because the bMaxPacketSize byte in the device descriptor is set
incorrectly. For example, the default settings call for a high-speed
connection, but the maxpacket value for ep0 ends up being set for a
Super-Speed connection.
This patch fixes the problem by initializing the gadget's max_speed
and the HCD flags correctly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The driver will forward errors to userspace after turning most of them
into -EIO. But all status codes are not equal. The -EPIPE (stall) in
particular can be seen more as a result of normal USB signaling than
an actual error. The state is automatically cleared by the USB core
without intervention from either driver or userspace.
And most devices and firmwares will never trigger a stall as a result
of GetEncapsulatedResponse. This is in fact a requirement for CDC WDM
devices. Quoting from section 7.1 of the CDC WMC spec revision 1.1:
The function shall not return STALL in response to
GetEncapsulatedResponse.
But this driver is also handling GetEncapsulatedResponse on behalf of
the qmi_wwan and cdc_mbim drivers. Unfortunately the relevant specs
are not as clear wrt stall. So some QMI and MBIM devices *will*
occasionally stall, causing the GetEncapsulatedResponse to return an
-EPIPE status. Translating this into -EIO for userspace has proven to
be harmful. Treating it as an empty read is safer, making the driver
behave as if the device was conforming to the CDC WDM spec.
There have been numerous reports of issues related to -EPIPE errors
from some newer CDC MBIM devices in particular, like for example the
Fibocom L831-EAU. Testing on this device has shown that the issues
go away if we simply ignore the -EPIPE status. Similar handling of
-EPIPE is already known from e.g. usb_get_string()
The -EPIPE log message is still kept to let us track devices with this
unexpected behaviour, hoping that it attracts attention from firmware
developers.
Cc: <stable@vger.kernel.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100938
Reported-and-tested-by: Christian Ehrig <christian.ehrig@mediamarktsaturn-bt.com>
Reported-and-tested-by: Patrick Chilton <chpatrick@gmail.com>
Reported-and-tested-by: Andreas Böhler <news@aboehler.at>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The user buffer has "uurb->buffer_length" bytes. If the kernel has more
information than that, we should truncate it instead of writing past
the end of the user's buffer. I added a WARN_ONCE() to help the user
debug the issue.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There used to be an integer overflow check in proc_do_submiturb() but
we removed it. It turns out that it's still required. The
uurb->buffer_length variable is a signed integer and it's controlled by
the user. It can lead to an integer overflow when we do:
num_sgs = DIV_ROUND_UP(uurb->buffer_length, USB_SG_SIZE);
If we strip away the macro then that line looks like this:
num_sgs = (uurb->buffer_length + USB_SG_SIZE - 1) / USB_SG_SIZE;
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
It's the first addition which can overflow.
Fixes: 1129d270cbfb ("USB: Increase usbfs transfer limit")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As a holdover from the old g_file_storage gadget, the g_mass_storage
legacy gadget driver attempts to unregister itself when its main
operating thread terminates (if it hasn't been unregistered already).
This is not strictly necessary; it was never more than an attempt to
have the gadget fail cleanly if something went wrong and the main
thread was killed.
However, now that the UDC core manages gadget drivers independently of
UDC drivers, this scheme doesn't work any more. A simple test:
modprobe dummy-hcd
modprobe g-mass-storage file=...
rmmod dummy-hcd
ends up in a deadlock with the following backtrace:
sysrq: SysRq : Show Blocked State
task PC stack pid father
file-storage D 0 1130 2 0x00000000
Call Trace:
__schedule+0x53e/0x58c
schedule+0x6e/0x77
schedule_preempt_disabled+0xd/0xf
__mutex_lock.isra.1+0x129/0x224
? _raw_spin_unlock_irqrestore+0x12/0x14
__mutex_lock_slowpath+0x12/0x14
mutex_lock+0x28/0x2b
usb_gadget_unregister_driver+0x29/0x9b [udc_core]
usb_composite_unregister+0x10/0x12 [libcomposite]
msg_cleanup+0x1d/0x20 [g_mass_storage]
msg_thread_exits+0xd/0xdd7 [g_mass_storage]
fsg_main_thread+0x1395/0x13d6 [usb_f_mass_storage]
? __schedule+0x573/0x58c
kthread+0xd9/0xdb
? do_set_interface+0x25c/0x25c [usb_f_mass_storage]
? init_completion+0x1e/0x1e
ret_from_fork+0x19/0x24
rmmod D 0 1155 683 0x00000000
Call Trace:
__schedule+0x53e/0x58c
schedule+0x6e/0x77
schedule_timeout+0x26/0xbc
? __schedule+0x573/0x58c
do_wait_for_common+0xb3/0x128
? usleep_range+0x81/0x81
? wake_up_q+0x3f/0x3f
wait_for_common+0x2e/0x45
wait_for_completion+0x17/0x19
fsg_common_put+0x34/0x81 [usb_f_mass_storage]
fsg_free_inst+0x13/0x1e [usb_f_mass_storage]
usb_put_function_instance+0x1a/0x25 [libcomposite]
msg_unbind+0x2a/0x42 [g_mass_storage]
__composite_unbind+0x4a/0x6f [libcomposite]
composite_unbind+0x12/0x14 [libcomposite]
usb_gadget_remove_driver+0x4f/0x77 [udc_core]
usb_del_gadget_udc+0x52/0xcc [udc_core]
dummy_udc_remove+0x27/0x2c [dummy_hcd]
platform_drv_remove+0x1d/0x31
device_release_driver_internal+0xe9/0x16d
device_release_driver+0x11/0x13
bus_remove_device+0xd2/0xe2
device_del+0x19f/0x221
? selinux_capable+0x22/0x27
platform_device_del+0x21/0x63
platform_device_unregister+0x10/0x1a
cleanup+0x20/0x817 [dummy_hcd]
SyS_delete_module+0x10c/0x197
? ____fput+0xd/0xf
? task_work_run+0x55/0x62
? prepare_exit_to_usermode+0x65/0x75
do_fast_syscall_32+0x86/0xc3
entry_SYSENTER_32+0x4e/0x7c
What happens is that removing the dummy-hcd driver causes the UDC core
to unbind the gadget driver, which it does while holding the udc_lock
mutex. The unbind routine in g_mass_storage tells the main thread to
exit and waits for it to terminate.
But as mentioned above, when the main thread exits it tries to
unregister the mass-storage function driver. Via the composite
framework this ends up calling usb_gadget_unregister_driver(), which
tries to acquire the udc_lock mutex. The result is deadlock.
The simplest way to fix the problem is not to be so clever: The main
thread doesn't have to unregister the function driver. The side
effects won't be so terrible; if the gadget is still attached to a USB
host when the main thread is killed, it will appear to the host as
though the gadget's firmware has crashed -- a reasonably accurate
interpretation, and an all-too-common occurrence for USB mass-storage
devices.
In fact, the code to unregister the driver when the main thread exits
is specific to g-mass-storage; it is not used when f-mass-storage is
included as a function in a larger composite device. Therefore the
entire mechanism responsible for this (the fsg_operations structure
with its ->thread_exits method, the fsg_common_set_ops() routine, and
the msg_thread_exits() callback routine) can all be eliminated. Even
the msg_registered bitflag can be removed, because now the driver is
unregistered in only one place rather than in two places.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
