summaryrefslogtreecommitdiff
path: root/drivers/watchdog/Kconfig
AgeCommit message (Collapse)Author
2020-10-24Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/socLinus Torvalds
Pull ARM SoC platform updates from Olof Johansson: "SoC changes, a substantial part of this is cleanup of some of the older platforms that used to have a bunch of board files. In particular: - Remove non-DT i.MX platforms that haven't seen activity in years, it's time to remove them. - A bunch of cleanup and removal of platform data for TI/OMAP platforms, moving over to genpd for power/reset control (yay!) - Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them closer to multiplatform support (not quite there yet, but getting close). There are a few other changes too, smaller fixlets, etc. For new platform support, the primary ones are: - New SoC: Hisilicon SD5203, ARM926EJ-S platform. - Cpufreq support for i.MX7ULP" * tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits) ARM: mstar: Select MStar intc ARM: stm32: Replace HTTP links with HTTPS ones ARM: debug: add UART early console support for SD5203 ARM: hisi: add support for SD5203 SoC ARM: omap3: enable off mode automatically clk: imx: imx35: Remove mx35_clocks_init() clk: imx: imx31: Remove mx31_clocks_init() clk: imx: imx27: Remove mx27_clocks_init() ARM: imx: Remove unused definitions ARM: imx35: Retrieve the IIM base address from devicetree ARM: imx3: Retrieve the AVIC base address from devicetree ARM: imx3: Retrieve the CCM base address from devicetree ARM: imx31: Retrieve the IIM base address from devicetree ARM: imx27: Retrieve the CCM base address from devicetree ARM: imx27: Retrieve the SYSCTRL base address from devicetree ARM: s3c64xx: bring back notes from removed debug-macro.S ARM: s3c24xx: fix Wunused-variable warning on !MMU ARM: samsung: fix PM debug build with DEBUG_LL but !MMU MAINTAINERS: mark linux-samsung-soc list non-moderated ARM: imx: Remove remnant board file support pieces ...
2020-10-21Merge tag 'linux-watchdog-5.10-rc1' of ↵Linus Torvalds
git://www.linux-watchdog.org/linux-watchdog Pull watchdog updates from Wim Van Sebroeck: - Add Toshiba Visconti watchdog driver - it87_wdt: add IT8772 + IT8784 - several fixes and improvements * tag 'linux-watchdog-5.10-rc1' of git://www.linux-watchdog.org/linux-watchdog: watchdog: Add Toshiba Visconti watchdog driver watchdog: bindings: Add binding documentation for Toshiba Visconti watchdog device watchdog: it87_wdt: add IT8784 ID watchdog: sp5100_tco: Enable watchdog on Family 17h devices if disabled watchdog: sp5100: Fix definition of EFCH_PM_DECODEEN3 watchdog: renesas_wdt: support handover from bootloader watchdog: imx7ulp: Watchdog should continue running for wait/stop mode watchdog: rti: Simplify with dev_err_probe() watchdog: davinci: Simplify with dev_err_probe() watchdog: cadence: Simplify with dev_err_probe() watchdog: remove unneeded inclusion of <uapi/linux/sched/types.h> watchdog: Use put_device on error watchdog: Fix memleak in watchdog_cdev_register watchdog: imx7ulp: Strictly follow the sequence for wdog operations watchdog: it87_wdt: add IT8772 ID watchdog: pcwd_usb: Avoid GFP_ATOMIC where it is not needed drivers: watchdog: rdc321x_wdt: Fix race condition bugs
2020-10-14watchdog: Add Toshiba Visconti watchdog driverNobuhiro Iwamatsu
Add the watchdog driver for Toshiba Visconti series. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> Reviewed-by: Punit Agrawal <punit1.agrawal@toshiba.co.jp> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20201005023012.603026-3-nobuhiro1.iwamatsu@toshiba.co.jp Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2020-09-17watchdog: add support for sl28cpld watchdogMichael Walle
Add support for the watchdog of the sl28cpld board management controller. This is part of a multi-function device driver. Signed-off-by: Michael Walle <michael@walle.cc> Acked-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2020-08-19ARM: samsung: remove HAVE_S3C2410_WATCHDOG and use direct dependenciesKrzysztof Kozlowski
A separate Kconfig option HAVE_S3C2410_WATCHDOG for Samsung SoCs is not really needed and the s3c24xx watchdog driver can depend on Samsung ARM architectures instead. The "HAVE_xxx_WATCHDOG" pattern of dependency is not popular and Samsung platforms are here exceptions. All others just depend on CONFIG_ARCH_xxx. This makes the code slightly smaller without any change in functionality. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Guenter Roeck <linux@roeck-us.net>
2020-08-05watchdog: Replace HTTP links with HTTPS onesAlexander A. Klimov
Rationale: Reduces attack surface on kernel devs opening the links for MITM as HTTPS traffic is much harder to manipulate. Deterministic algorithm: For each file: If not .svg: For each line: If doesn't contain `\bxmlns\b`: For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`: If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`: If both the HTTP and HTTPS versions return 200 OK and serve the same content: Replace HTTP with HTTPS. Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20200713205821.38223-1-grandmaster@al2klimov.de Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2020-06-14treewide: replace '---help---' in Kconfig files with 'help'Masahiro Yamada
Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over '---help---'"), the number of '---help---' has been gradually decreasing, but there are still more than 2400 instances. This commit finishes the conversion. While I touched the lines, I also fixed the indentation. There are a variety of indentation styles found. a) 4 spaces + '---help---' b) 7 spaces + '---help---' c) 8 spaces + '---help---' d) 1 space + 1 tab + '---help---' e) 1 tab + '---help---' (correct indentation) f) 1 tab + 1 space + '---help---' g) 1 tab + 2 spaces + '---help---' In order to convert all of them to 1 tab + 'help', I ran the following commend: $ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/' Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
2020-05-25watchdog: Add new arm_smc_wdt watchdog driverJulius Werner
This patch adds a watchdog driver that can be used on ARM systems with the appropriate watchdog implemented in Secure Monitor firmware. The driver communicates with firmware via a Secure Monitor Call. This may be useful for platforms using TrustZone that want the Secure Monitor firmware to have the final control over the watchdog. This is implemented on mt8173 chromebook devices oak, elm and hana in arm trusted firmware file plat/mediatek/mt8173/drivers/wdt/wdt.c. Signed-off-by: Julius Werner <jwerner@chromium.org> Signed-off-by: Evan Benn <evanbenn@chromium.org> Reviewed-by: Julius Werner <jwerner@chromium.org> Tested-by: Xingyu Chen<xingyu.chen@amlogic.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20200505131242.v6.2.Ia92bb4d4ce84bcefeba1d00aaa1c1e919b6164ef@changeid Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2020-05-25watchdog: iTCO: fix link errorArnd Bergmann
When the MFD driver is a loadable module, the watchdog driver fails to get linked into the kernel: drivers/watchdog/iTCO_wdt.o: In function `update_no_reboot_bit_pmc': iTCO_wdt.c:(.text+0x54f): undefined reference to `intel_pmc_gcr_update' The code is written to support operation without the MFD driver, so add a Kconfig dependency that allows this, while disallowing the watchdog to be built-in when the MFD driver is a module. Fixes: 25f1ca31e230 ("platform/x86: intel_pmc_ipc: Convert to MFD") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Link: https://lore.kernel.org/r/20200428212959.2993304-1-arnd@arndb.de Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2020-05-25watchdog: ts72xx_wdt: fix build errorShyam Saini
If TS72XX_WATCHDOG is y and WATCHDOG_CORE is not enabled or its m, then building fails: drivers/watchdog/ts72xx_wdt.o: in function `ts72xx_wdt_probe': ts72xx_wdt.c:(.text+0x14c): undefined reference to \ `watchdog_init_timeout' ts72xx_wdt.c:(.text+0x15c): undefined reference to \ `devm_watchdog_register_device' Select WATCHDOG_CORE to fix this. Signed-off-by: Shyam Saini <shyam.saini@savoirfairelinux.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20200406215008.30468-1-shyam.saini@savoirfairelinux.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2020-04-01watchdog: Add K3 RTI watchdog supportTero Kristo
Texas Instruments K3 SoCs contain an RTI (Real Time Interrupt) module which can be used as a watchdog. This IP provides a support for windowed watchdog mode, in which the watchdog must be petted within a certain time window. If it is petted either too soon, or too late, a watchdog error will be triggered. Signed-off-by: Tero Kristo <t-kristo@ti.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20200312095808.19907-4-t-kristo@ti.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2020-02-17watchdog: da9062: Add dependency on I2CGuenter Roeck
Since commit 057b52b4b3d58 ("watchdog: da9062: make restart handler atomic safe"), the driver calls i2c functions directly. It now therefore depends on I2C. This is a hard dependency which overrides COMPILE_TEST. Reported-by: kbuild test robot <lkp@intel.com> Reported-by: Randy Dunlap <rdunlap@infradead.org> Fixes: 057b52b4b3d58 ("watchdog: da9062: make restart handler atomic safe") Cc: Marco Felsch <m.felsch@pengutronix.de> Cc: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Cc: Stefan Lengfeld <contact@stefanchrist.eu> Reviewed-by: Marco Felsch <m.felsch@pengutronix.de> Acked-by: Randy Dunlap <rdunlap@infradead.org> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2020-02-17watchdog: fix mtk_wdt.c RESET_CONTROLLER build errorRandy Dunlap
Fix build error when CONFIG_RESET_CONTROLLER is not set by selecting RESET_CONTROLLER. ld: drivers/watchdog/mtk_wdt.o: in function `mtk_wdt_probe': mtk_wdt.c:(.text+0x3ec): undefined reference to `devm_reset_controller_register' Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Fixes: c254e103082b74e ("watchdog: mtk_wdt: mt8183: Add reset controller") Cc: Wim Van Sebroeck <wim@linux-watchdog.org> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: linux-watchdog@vger.kernel.org Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/77c1e557-4941-3806-2933-6c3583576390@infradead.org Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2019-12-30watchdog: tqmx86_wdt: Fix build errorYueHaibing
If TQMX86_WDT is y and WATCHDOG_CORE is m, building fails: drivers/watchdog/tqmx86_wdt.o: In function `tqmx86_wdt_probe': tqmx86_wdt.c:(.text+0x46e): undefined reference to `watchdog_init_timeout' tqmx86_wdt.c:(.text+0x4e0): undefined reference to `devm_watchdog_register_device' Select WATCHDOG_CORE to fix this. Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: e3c21e088f89 ("watchdog: tqmx86: Add watchdog driver for the IO controller") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20191206124259.25880-1-yuehaibing@huawei.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2019-12-30watchdog: max77620_wdt: fix potential build errorsDavid Engraf
max77620_wdt uses watchdog core functions. Enable CONFIG_WATCHDOG_CORE to fix potential build errors. Signed-off-by: David Engraf <david.engraf@sysgo.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20191127084617.16937-1-david.engraf@sysgo.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2019-11-18watchdog: jz4740: Drop dependency on MACH_JZ47xxPaul Cercueil
Depending on MACH_JZ47xx prevent us from creating a generic kernel that works on more than one MIPS board. Instead, we just depend on MIPS being set. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Acked-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20191023174714.14362-3-paul@crapouillou.net Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2019-11-18watchdog: jz4740: Use regmap provided by TCU driverPaul Cercueil
Since we broke the ABI by changing the clock, the driver was also updated to use the regmap provided by the TCU driver. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Tested-by: Mathieu Malaterre <malat@debian.org> Tested-by: Artur Rojek <contact@artur-rojek.eu> Acked-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20191023174714.14362-2-paul@crapouillou.net Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2019-11-18watchdog: jz4740: Use WDT clock provided by TCU driverPaul Cercueil
Instead of requesting the "ext" clock and handling the watchdog clock divider and gating in the watchdog driver, we now request and use the "wdt" clock that is supplied by the ingenic-timer "TCU" driver. The major benefit is that the watchdog's clock rate and parent can now be specified from within devicetree, instead of hardcoded in the driver. Also, this driver won't poke anymore into the TCU registers to enable/disable the clock, as this is now handled by the TCU driver. On the bad side, we break the ABI with devicetree - as we now request a different clock. In this very specific case it is still okay, as every Ingenic JZ47xx-based board out there compile the devicetree within the kernel; so it's still time to push breaking changes, in order to get a clean devicetree that won't break once it musn't. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Tested-by: Mathieu Malaterre <malat@debian.org> Tested-by: Artur Rojek <contact@artur-rojek.eu> Acked-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20191023174714.14362-1-paul@crapouillou.net Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2019-11-18watchdog: w83627hf_wdt: Support NCT6116DSrikanth Krishnakar
The watchdog controller on NCT6116D is compatible with NCT6102D. Extend the support to enable SuperIO based NCT6116D watchdog device. Signed-off-by: Srikanth Krishnakar <Srikanth_Krishnakar@mentor.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20190918160458.10108-1-Srikanth_Krishnakar@mentor.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2019-09-17watchdog: f71808e_wdt: Add F81803 supportJaret Cantu
This adds watchdog support for the Fintek F81803 Super I/O chip. Testing was done on the Seneca XK-QUAD. Signed-off-by: Jaret Cantu <jaret.cantu@timesys.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20190912175550.9340-1-jaret.cantu@timesys.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2019-09-17watchdog: Add i.MX7ULP watchdog supportAnson Huang
The i.MX7ULP Watchdog Timer (WDOG) module is an independent timer that is available for system use. It provides a safety feature to ensure that software is executing as planned and that the CPU is not stuck in an infinite loop or executing unintended code. If the WDOG module is not serviced (refreshed) within a certain period, it resets the MCU. Add driver support for i.MX7ULP watchdog. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/1566999303-18795-2-git-send-email-Anson.Huang@nxp.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2019-09-16watchdog: remove w90x900 driverArnd Bergmann
The ARM w90x900 platform is getting removed, so this driver is obsolete Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20190809202749.742267-7-arnd@arndb.de Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2019-09-16watchdog: remove ks8695 driverArnd Bergmann
The platform is getting removed, so there are no remaining users of this driver. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20190809202749.742267-5-arnd@arndb.de Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2019-09-16watchdog: pnx4008_wdt: allow compile-testingArnd Bergmann
The only thing that prevents building this driver on other platforms is the mach/hardware.h include, which is not actually used here at all, so remove the line and allow CONFIG_COMPILE_TEST. Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20190809144043.476786-4-arnd@arndb.de Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2019-07-08docs: watchdog: convert docs to ReST and rename to *.rstMauro Carvalho Chehab
Convert those documents and prepare them to be part of the kernel API book, as most of the stuff there are related to the Kernel interfaces. Still, in the future, it would make sense to split the docs, as some of the stuff is clearly focused on sysadmin tasks. The conversion is actually: - add blank lines and identation in order to identify paragraphs; - fix tables markups; - add some lists markups; - mark literal blocks; - adjust title markups. At its new index.rst, let's add a :orphan: while this is not linked to the main index.rst file, in order to avoid build warnings. Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2019-07-08watchdog: introduce CONFIG_WATCHDOG_OPEN_TIMEOUTRasmus Villemoes
This allows setting a default value for the watchdog.open_timeout commandline parameter via Kconfig. Some BSPs allow remote updating of the kernel image and root file system, but updating the bootloader requires physical access. Hence, if one has a firmware update that requires relaxing the watchdog.open_timeout a little, the value used must be baked into the kernel image itself and cannot come from the u-boot environment via the kernel command line. Being able to set the initial value in .config doesn't change the fact that the value on the command line, if present, takes precedence, and is of course immensely useful for development purposes while one has console acccess, as well as usable in the cases where one can make a permanent update of the kernel command line. Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2019-07-08watchdog: imx_sc: Add pretimeout supportAnson Huang
i.MX system controller watchdog can support pretimeout IRQ via general SCU MU IRQ, it depends on IMX_SCU and driver MUST be probed after SCU IPC ready, then enable corresponding SCU IRQ group and register SCU IRQ notifier, when watchdog pretimeout IRQ fires, SCU MU IRQ will be handled and watchdog pretimeout notifier will be called to handle the event. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2019-05-21treewide: Add SPDX license identifier - Makefile/KconfigThomas Gleixner
Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-08watchdog: Enforce that at least one pretimeout governor is enabledGuenter Roeck
Since commit "watchdog: Use depends instead of select for pretimeout governors", it was possible to enable pretimeout governors but keep all of them disabled. Doing this results in the following build failure. ../drivers/watchdog/watchdog_pretimeout.c: In function ‘watchdog_register_governor’: ../drivers/watchdog/watchdog_pretimeout.c:139:26: error: ‘WATCHDOG_PRETIMEOUT_DEFAULT_GOV’ undeclared if (!strncmp(gov->name, WATCHDOG_PRETIMEOUT_DEFAULT_GOV, Since it does not make sense to enable pretimeout support but disable all pretimeout governors, enforce that at least one of them is always enabled. Fixes: f627ac0e12cd ("watchdog: Use depends instead of select for pretimeout governors") Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2019-05-05watchdog: Improve Kconfig entry ordering and dependenciesGuenter Roeck
HPWDT_NMI_DECODING depends on HP_WATCHDOG and should be next to it. This helps menuconfig identify HPWDT_NMI_DECODING as depending on HP_WATCHDOG. BCM_KONA_WDT_DEBUG depends on BCM_KONA_WDT which depends on COMPILE_TEST. Enabling BCM_KONA_WDT_DEBUG without BCM_KONA_WDT does not make sense, so drop the COMPILE_TEST dependency from it. This also improves menuconfig, which now properly associates BCM_KONA_WDT_DEBUG with BCM_KONA_WDT. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2019-05-05watchdog: npcm: Enable modular buildsGuenter Roeck
Most of the NPCM7XX drivers can be built as modules. The NPCM7XX watchdog driver code supports building it as module, but its configuration option is set to bool. Make itr tristate to actually support modular builds. This improves consistency with other drivers for the same platform and enables including the driver in multi- platform configurations. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2019-05-05watchdog: Make watchdog core configurable as moduleGuenter Roeck
Under some circumstances it may be desirable to configure the watchdog core as module. Enable it. As part of this change, mark pretimeout governors as depending on the watchdog core. This is necessary to prevent governors from being built into the kernel if the watchdog core is built as module. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2019-05-05watchdog: Move pretimeout governor configuration upGuenter Roeck
Watchdog pretimeout configuration was at the end of the Kconfig file, after individual watchdog drivers, and thus easy to miss. Move it right after basic watchdog option declarations. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2019-05-05watchdog: Use depends instead of select for pretimeout governorsGuenter Roeck
Watchdog pretimeout governors were enabled from the default governor selection using "select". As a result, the default governor was always built into the kernel, even if no watchdog driver was loaded. By using "depends on" instead of "select", we are in better control, and the governors can all be built as modules. At the same time, set the default configuration option for pretimeout governors to match WATCHDOG_CORE (meaning all pretimeout governors are by default enabled if pretimeout support is enabled). The practical impact of this change is minimal. Previously, selecting a default governor automatically enabled that governor. Now, a default governor can only be selected if that governor has been enabled. Consequently, the order of governor selection is now reversed: The governor selection is now first, followed by default governor selection. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2019-05-05watchdog: imx_sc: Add i.MX system controller watchdog supportAnson Huang
i.MX8QXP is an ARMv8 SoC which has a Cortex-M4 system controller inside, the system controller is in charge of controlling power, clock and watchdog etc.. This patch adds i.MX system controller watchdog driver support, watchdog operation needs to be done in secure EL3 mode via ARM-Trusted-Firmware, using SMC call, CPU will trap into ARM-Trusted-Firmware and then it will request system controller to do watchdog operation via IPC. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2019-05-05watchdog: bd70528: Initial support for ROHM BD70528 watchdog blockMatti Vaittinen
Initial support for watchdog block included in ROHM BD70528 power management IC. Configurations for low power states are still to be checked. Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> Acked-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2019-05-05watchdog: fix compile time error of pretimeout governorsVladimir Zapolskiy
CONFIG_WATCHDOG_PRETIMEOUT_GOV build symbol adds watchdog_pretimeout.o object to watchdog.o, the latter is compiled only if CONFIG_WATCHDOG_CORE is selected, so it rightfully makes sense to add it as a dependency. The change fixes the next compilation errors, if CONFIG_WATCHDOG_CORE=n and CONFIG_WATCHDOG_PRETIMEOUT_GOV=y are selected: drivers/watchdog/pretimeout_noop.o: In function `watchdog_gov_noop_register': drivers/watchdog/pretimeout_noop.c:35: undefined reference to `watchdog_register_governor' drivers/watchdog/pretimeout_noop.o: In function `watchdog_gov_noop_unregister': drivers/watchdog/pretimeout_noop.c:40: undefined reference to `watchdog_unregister_governor' drivers/watchdog/pretimeout_panic.o: In function `watchdog_gov_panic_register': drivers/watchdog/pretimeout_panic.c:35: undefined reference to `watchdog_register_governor' drivers/watchdog/pretimeout_panic.o: In function `watchdog_gov_panic_unregister': drivers/watchdog/pretimeout_panic.c:40: undefined reference to `watchdog_unregister_governor' Reported-by: Kuo, Hsuan-Chi <hckuo2@illinois.edu> Fixes: ff84136cb6a4 ("watchdog: add watchdog pretimeout governor framework") Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2019-03-11Merge tag 'linux-watchdog-5.1-rc1' of ↵Linus Torvalds
git://www.linux-watchdog.org/linux-watchdog Pull watchdog updates from Wim Van Sebroeck: - a new watchdog driver for the Mellanox systems - renesas-wdt: Document r8a77470 support - numerous 'Mark expected switch fall-throughs' - qcom: Add suspend/resume support - some small fixes and documentation updates * tag 'linux-watchdog-5.1-rc1' of git://www.linux-watchdog.org/linux-watchdog: watchdog: w83877f_wdt: Mark expected switch fall-through watchdog: sc520_wdt: Mark expected switch fall-through watchdog: sbc60xxwdt: Mark expected switch fall-through watchdog: smsc37b787_wdt: Mark expected switch fall-through watchdog: sc1200: Mark expected switch fall-through watchdog: pc87413: Mark expected switch fall-through Documentation/watchdog: Add documentation mlx-wdt driver watchdog: mlx-wdt: introduce a watchdog driver for Mellanox systems. platform_data/mlxreg: additions for Mellanox watchdog driver. watchdog: Update sysfs documentation. watchdog: dw: remove useless pr_fmt watchdog: pika_wdt: drop pointless static qualifier in pikawdt_init watchdog/hpwdt: Update Kconfig documentation dt-bindings: watchdog: renesas-wdt: Document r8a77470 support watchdog: qcom: Add suspend/resume support
2019-03-02watchdog: mlx-wdt: introduce a watchdog driver for Mellanox systems.Michael Shych
Introduce watchdog driver for a various range of Mellanox Ethernet and Infiniband switch systems. Watchdog driver for Mellanox watchdog devices, implemented in programmable logic device. Main and auxiliary watchdog devices can exist on the same system. There are several actions that can be defined in the watchdog: system reset, start fans on full speed and increase a counter. The last 2 actions are performed without a system reset. Actions without reset are provided for auxiliary watchdog devices, which is optional. Access to HW registers is performed through generic regmap interface. There are 2 types of HW watchdog implementations. Type 1: actual HW timeout can be defined as power of 2 msec. e.g. timeout 20 sec will be rounded up to 32768 msec.; maximum timeout period is 32 sec (32768 msec.); get time-left isn't supported Type 2: actual HW timeout is defined in sec. and it's the same as user-defined timeout; maximum timeout is 255 sec; get time-left is supported; Watchdog driver is probed from the common mlx_platform driver. Signed-off-by: Michael Shych <michaelsh@mellanox.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2019-03-02watchdog/hpwdt: Update Kconfig documentationJerry Hoemann
Update documentation relating to HPWDT_NMI_DECODING to reflect its current usage. Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2019-01-16watchdog: stpmic1: Add STPMIC1 watchdog driverPascal PAILLET-LME
The STPMIC1 PMIC embeds a watchdog which is disabled by default. As soon as the watchdog is started, it must be refreshed periodically otherwise the PMIC goes off. Signed-off-by: Pascal Paillet <p.paillet@st.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2018-12-24watchdog: tqmx86: Add watchdog driver for the IO controllerAndrew Lunn
Some TQ-Systems ComExpress modules have an IO controller with a watchdog timer. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2018-12-22watchdog: Add pm8916 watchdog driverLoic Poulain
The PM816 module is a versatile PMIC with many diverse functions integrated, including, a watchdog. This watchdog is subcomponent of the PON (Power On) peripheral, in the same way as pwrkey/resin buttons. It works with two timers (2-stages), the first one generates an IRQ to the main SoC (APQ8016/MSM8916), the second one performs the reset. This driver expects the following device hierarchy: [pm8916]->[pm8916-pon]->[pm8916-wdt] It uses the pm8916 regmap to access PM8916 registers. Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2018-11-17watchdog: npcm: Modify npcm watchdog kconfig arch parameterTomer Maimon
Modify Nuvoton watchdog Kconfig default supported architecture name to ARCH_NPCM7XX because ARCH_NPCM750 architecture name is not supported. Signed-off-by: Tomer Maimon <tmaimon77@gmail.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2018-10-13watchdog: Add support for Armada 37xx CPU watchdogMarek Behún
This adds support for the CPU watchdog found on Marvell Armada 37xx SoCs. There are 4 counters which can be set as CPU watchdog counters. This driver uses the second counter (ID 1, counting from 0) as watchdog counter, and first counter (ID 0) to implement pinging on the second counter without the need to disable it. Since counters IDs 2 and 3 are enabled already before even U-Boot starts, this driver does not use them at all, for example by adding a device tree property for counter selection. Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2018-10-02watchdog: lantiq: Convert to watchdog_deviceHauke Mehrtens
Instead of doing the ioctl handling manually just use register a watchdog_device and let the watchdog framework do the ioctl handling. This also removes the ltq_wdt_bootstatus_set typedef and replaces it with a structure providing the chip specific functions pointer. The watchdog_init_timeout() function is now used and the initial timeout can be provided in device tree. If the watchdog was already activated it will not be stopped any more, but the settings from the driver will be used and the watchdog subsystem will take care. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2018-08-06watchdog: fix dependencies of menz69_wdt.oJohannes Thumshirn
Currently menz69_wdt.ko has a dependency on MCB or COMPILE_TEST. But it actually needs symbols exported by MCB so the || COMPILE_TEST is wrong. Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2018-08-02watchdog: add driver for the MEN 16z069 IP-CoreJohannes Thumshirn
Add a driver for the MEN 16z069 Watchdog and Reset Controller IP-Core. Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Michael Moese <mmoese@suse.de> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2018-04-13Merge tag 'linux-watchdog-4.17-rc1' of ↵Linus Torvalds
git://www.linux-watchdog.org/linux-watchdog Pull watchdog updates from Wim Van Sebroeck: - Add Nuvoton NPCM watchdog driver - renesas_wdt: Add R-Car Gen2 support - renesas_wdt: add suspend/resume and restart handler support - hpwdt: convert to watchdog core and improve NMI - improve timeout setting/handling in various drivers - coh901327: make license text and module licence match - fix error handling in asm9260_wdt, sprd_wdt and davinci_wdt - aspeed imrovements - dw improvements (for control register & suspend/resume) - add SPDX identifiers for watchdog subsystem * tag 'linux-watchdog-4.17-rc1' of git://www.linux-watchdog.org/linux-watchdog: (35 commits) watchdog: davinci_wdt: fix error handling in davinci_wdt_probe() watchdog: add SPDX identifiers for watchdog subsystem watchdog: aspeed: Allow configuring for alternate boot watchdog: Add Nuvoton NPCM watchdog driver dt-bindings: watchdog: Add Nuvoton NPCM description watchdog: dw: save/restore control and timeout across suspend/resume watchdog: dw: RMW the control register watchdog: sprd_wdt: Fix error handling in sprd_wdt_enable() watchdog: aspeed: Fix translation of reset mode to ctrl register watchdog: renesas_wdt: Add restart handler watchdog: renesas_wdt: Add R-Car Gen2 support watchdog: renesas_wdt: Add suspend/resume support watchdog: f71808e_wdt: Fix WD_EN register read watchdog: hpwdt: Update driver version. watchdog: hpwdt: Add dynamic debug watchdog: hpwdt: Programable Pretimeout NMI watchdog: hpwdt: remove allow_kdump module parameter. watchdog: hpwdt: condition early return of NMI handler on iLO5 watchdog: hpwdt: Modify to use watchdog core. watchdog: hpwdt: Update nmi_panic message. ...
2018-04-05Merge tag 'gpio-v4.17-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio Pull GPIO updates from Linus Walleij: "This is the bulk of GPIO changes for the v4.17 kernel cycle: New drivers: - Nintendo Wii GameCube GPIO, known as "Hollywood" - Raspberry Pi mailbox service GPIO expander - Spreadtrum main SC9860 SoC and IEC GPIO controllers. Improvements: - Implemented .get_multiple() callback for most of the high-performance industrial GPIO cards for the ISA bus. - ISA GPIO drivers now select the ISA_BUS_API instead of depending on it. This is merged with the same pattern for all the ISA drivers and some other Kconfig cleanups related to this. Cleanup: - Delete the TZ1090 GPIO drivers following the deletion of this SoC from the ARM tree. - Move the documentation over to driver-api to conform with the rest of the kernel documentation build. - Continue to make the GPIO drivers include only <linux/gpio/driver.h> and not the too broad <linux/gpio.h> that we want to get rid of. - Managed to remove VLA allocation from two drivers pending more fixes in this area for the next merge window. - Misc janitorial fixes" * tag 'gpio-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits) gpio: Add Spreadtrum PMIC EIC driver support gpio: Add Spreadtrum EIC driver support dt-bindings: gpio: Add Spreadtrum EIC controller documentation gpio: ath79: Fix potential NULL dereference in ath79_gpio_probe() pinctrl: qcom: Don't allow protected pins to be requested gpiolib: Support 'gpio-reserved-ranges' property gpiolib: Change bitmap allocation to kmalloc_array gpiolib: Extract mask allocation into subroutine dt-bindings: gpio: Add a gpio-reserved-ranges property gpio: mockup: fix a potential crash when creating debugfs entries gpio: pca953x: add compatibility for pcal6524 and pcal9555a gpio: dwapb: Add support for a bus clock gpio: Remove VLA from xra1403 driver gpio: Remove VLA from MAX3191X driver gpio: ws16c48: Implement get_multiple callback gpio: gpio-mm: Implement get_multiple callback gpio: 104-idi-48: Implement get_multiple callback gpio: 104-dio-48e: Implement get_multiple callback gpio: pcie-idio-24: Implement get_multiple/set_multiple callbacks gpio: pci-idio-16: Implement get_multiple callback ...
generated by cgit (git 2.34.1) at 2024-06-09 17:57:30 +0000