| Age | Commit message (Collapse) | Author |
|---|
|
Cooled SFP+ transceivers need a longer initialisation (startup) time.
Select the initialisation time depending on the cooled option bit.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
phy_error() is called from phy_interrupt() or phy_state_machine(), and
uses WARN_ON() to print a backtrace. The backtrace is not useful when
reporting a PHY error.
However, a system may contain multiple ethernet PHYs, and phy_error()
gives no clue which one caused the problem.
Replace WARN_ON() with a call to phydev_err() so that we can see which
PHY had an error, and also inform the user that we are halting the PHY.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Allow the PHY to probe when there is no firmware, but do not allow the
link to come up by forcing the PHY state to PHY_HALTED in a similar way
to phy_error().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Provide phy driver start/stop hooks so that the PHY driver knows when
the network driver is starting or stopping. This will be used for the
Marvell 10G driver so that we can sanely refuse to start if the PHYs
firmware is not present, and also so that we can sanely support SFPs
behind the PHY.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Support reporting the hardware resolved pause enablement states via
phylib, overriding our software implementation.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Allow phylib drivers to pass the hardware-resolved pause state to MAC
drivers, rather than using the software-based pause resolution code.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add support for configuring the LEDs. Macchiatobin has an oddity in
that the left LED goes out when the cable is connected, and flashes
when there's link activity. This is because the reset default for
the LED outputs assume that the LED is connected to supply, not to
ground. Add support for configuring the LED modes and polarities.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add support for the downshift tunable for the Marvell 88x3310 PHY.
Downshift is only usable with firmware 0.3.5.0 and later.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
There are several places which open code comparing PHY IDs. Provide a
couple of helpers to assist with this, using a slightly simpler test
than the original:
- phy_id_compare() compares two arbitary PHY IDs and a mask of the
significant bits in the ID.
- phydev_id_compare() compares the bound phydev with the specified
PHY ID, using the bound driver's mask.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The at803x driver contains a function, at803x_match_phy_id(), which
tests whether the PHY ID matches the value passed, comparing phy_id
with phydev->phy_id and testing all bits that have a "one" in the
mask, phydev->drv->phy_id_mask.
This is the same test that is used to match the driver, with phy_id
replaced with the driver specified ID, phydev->drv->phy_id.
Hence, we already know the value of the bits being tested if we look
at phydev->drv->phy_id directly, and we do not require a complicated
test to check them. Test directly against phydev->drv->phy_id instead.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The SGMII PCS PHY needs to be updated with the link configuration in
the mac_link_up() call rather than in mac_config(). However,
mtk_sgmii_setup_mode_force() programs the SGMII block during
mac_config() when using 802.3z interface modes with the link
configuration.
Split that functionality from mtk_sgmii_setup_mode_force(), moving it
to a new mtk_sgmii_link_up() function, and call it from mac_link_up().
This does not look correct to me: 802.3z modes operate at a fixed
speed. The contents of mtk_sgmii_link_up() look more appropriate for
SGMII mode, but the original code definitely did not call
mtk_sgmii_setup_mode_force() for SGMII mode but only 802.3z mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Implement the .phylink_get_interfaces method for mv88e6xxx driver.
We are currently only interested in SGMII, 1000base-x and 2500base-x
modes (for the SFP code). USXGMII and 10gbase-r can be added later for
Amethyst. XAUI and RXAUI are irrelevant for SFP (but maybe not for
QSFP?).
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Fill in the phy interface mode bitmap for the Marvell mvpp2 driver, so
phylink can know which interfaces are supported by the MAC.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Fill in the phy interface mode bitmap for the Marvell mvneta driver, so
phylink can know which interfaces are supported by the MAC.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Where a MAC provides the PHY interface mode capabilities, use the PHY
interface mode bitmaps to select the operating interface mode for
optical SFP modules, rather than using the linkmode bitmaps.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
We currently parse the SFP EEPROM to a bitmap of ethtool link modes,
and then attempt to convert the link modes to a PHY interface mode.
While this works at present, there are cases where this is sub-optimal.
For example, where a module can operate with several different PHY
interface modes.
To start addressing this, arrange for the SFP EEPROM parsing to also
provide a bitmap of the possible PHY interface modes.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
We only need to fiddle about with the supported mask after we have
validated the user's requested parameters. Simplify and streamline the
code by moving the linkmode copy and update of the autoneg bit after
validating the user's request.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Augment the phy link debug prints with the pause state.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Vasily Gorbik:
- Fix a couple of late pt_regs flags handling findings of conversion to
generic entry.
- Fix potential register clobbering in stack switch helper.
- Fix thread/group masks for offline cpus.
- Fix cleanup of mdev resources when remove callback is invoked in
vfio-ap code.
* tag 's390-5.13-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/stack: fix possible register corruption with stack switch helper
s390/topology: clear thread/group maps for offline cpus
s390/vfio-ap: clean up mdev resources when remove callback invoked
s390: clear pt_regs::flags on irq entry
s390: fix system call restart with multiple signals
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Two last-minute fixes:
- Put an fwnode in the errorpath in the SGPIO driver
- Fix the number of GPIO lines per bank in the STM32 driver"
* tag 'pinctrl-v5.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: stm32: fix the reported number of GPIO lines per bank
pinctrl: microchip-sgpio: Put fwnode in error case during ->probe()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two small fixes, both in upper layer drivers (scsi disk and cdrom).
The sd one is fixing a commit changing revalidation that came from the
block tree a while ago (5.10) and the sr one adds handling of a
condition we didn't previously handle for manually removed media"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sd: Call sd_revalidate_disk() for ioctl(BLKRRPART)
scsi: sr: Return appropriate error code when disk is ejected
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Three more driver bugfixes and an annotation fix for the core"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: robotfuzz-osif: fix control-request directions
i2c: dev: Add __user annotation
i2c: cp2615: check for allocation failure in cp2615_i2c_recv()
i2c: i801: Ensure that SMBHSTSTS_INUSE_STS is cleared when leaving i801_access
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull device properties framework fix from Rafael Wysocki:
"Fix a NULL pointer dereference introduced by a recent commit and
occurring when device_remove_software_node() is used with a device
that has never been registered (Heikki Krogerus)"
* tag 'devprop-5.13-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
software node: Handle software node injection to an existing device properly
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fix from Juergen Gross:
"A fix for a regression introduced in 5.12: when migrating an irq
related to a Xen user event to another cpu, a race might result
in a WARN() triggering"
* tag 'for-linus-5.13b-rc8-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/events: reset active flag for lateeoi events later
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
- fix wake-up interrupt support on gpio-mxc
- zero the padding bytes in a structure passed to user-space in the
GPIO character device
- require HAS_IOPORT_MAP in two drivers that need it to fix a Kbuild
issue
* tag 'gpio-fixes-for-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: AMD8111 and TQMX86 require HAS_IOPORT_MAP
gpiolib: cdev: zero padding during conversion to gpioline_info_changed
gpio: mxc: Fix disabled interrupt wake-up support
|
|
Both of these drivers use ioport_map(), so they need to
depend on HAS_IOPORT_MAP. Otherwise, they cannot be built
even with COMPILE_TEST on architectures without an ioport
implementation, such as ARCH=um.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Pull drm fixes from Dave Airlie:
"This is a bit bigger than I'd like at this stage, and I guess last
week was extra quiet, but it's mostly one fix across three drivers to
wait for buffer move pinning to complete.
There was one locking change that got reverted so it's just noise.
Otherwise the amdgpu/nouveau changes are for known regressions, and
otherwise it's just misc changes in kmb/atmel/vc4 drivers.
Summary:
core:
- auth locking change + brown paper bag revert
radeon/nouveau/amdgpu/ttm:
- wait for BO to be pinned after moving it (same fix in three
drivers)
amdgpu:
- Revert GFX9/10 doorbell fixes, we just end up trading one bug for
another
- Potential memory corruption fix in framebuffer handling
nouveau:
- fix regression checking dma addresses
kmb:
- error return fix
atmel-hlcdc:
- fix kernel warnings at boot
- enable async flips
vc4:
- fix CPU hang due to power management"
* tag 'drm-fixes-2021-06-25' of git://anongit.freedesktop.org/drm/drm:
drm/nouveau: fix dma_address check for CPU/GPU sync
drm/kmb: Fix error return code in kmb_hw_init()
drm/amdgpu: wait for moving fence after pinning
drm/radeon: wait for moving fence after pinning
drm/nouveau: wait for moving fence after pinning v2
Revert "drm: add a locked version of drm_is_current_master"
Revert "drm/amdgpu/gfx9: fix the doorbell missing when in CGPG issue."
Revert "drm/amdgpu/gfx10: enlarge CP_MEC_DOORBELL_RANGE_UPPER to cover full doorbell."
drm/amdgpu: Call drm_framebuffer_init last for framebuffer init
drm: add a locked version of drm_is_current_master
drm/atmel-hlcdc: Allow async page flips
drm/panel: ld9040: reference spi_device_id table
drm: atmel_hlcdc: Enable the crtc vblank prior to crtc usage.
drm/vc4: hdmi: Make sure the controller is powered in detect
drm/vc4: hdmi: Move the HSM clock enable to runtime_pm
|
|
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Control transfers without a data stage are treated as OUT requests by
the USB stack and should be using usb_sndctrlpipe(). Failing to do so
will now trigger a warning.
Fix the OSIFI2C_SET_BIT_RATE and OSIFI2C_STOP requests which erroneously
used the osif_usb_read() helper and set the IN direction bit.
Reported-by: syzbot+9d7dadd15b8819d73f41@syzkaller.appspotmail.com
Fixes: 83e53a8f120f ("i2c: Add bus driver for for OSIF USB i2c device.")
Cc: stable@vger.kernel.org # 3.14
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
A DMA address check for nouveau, an error code return fix for kmb, fixes
to wait for a moving fence after pinning the BO for amdgpu, nouveau and
radeon, a crtc and async page flip fix for atmel-hlcdc and a cpu hang
fix for vc4.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210624190353.wyizoil3wqrrxz5d@gilmour
|
|
Fix Sparse warnings:
drivers/i2c/i2c-dev.c:546:19: warning: incorrect type in assignment (different address spaces)
drivers/i2c/i2c-dev.c:549:53: warning: incorrect type in argument 2 (different address spaces)
compat_ptr() returns a pointer tagged __user which gets assigned to a
pointer missing the __user annotation. The same pointer is passed to
copy_from_user() as an argument where it is expected to have the __user
annotation. Fix both by adding the __user annotation to the pointer.
Fixes: 7d5cb45655f2 ("i2c compat ioctls: move to ->compat_ioctl()")
Signed-off-by: Andreas Hecht <andreas.e.hecht@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fix from Ulf Hansson:
"Use memcpy_to/fromio for dram-access-quirk in the meson-gx host
driver"
* tag 'mmc-v5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: meson-gx: use memcpy_to/fromio for dram-access-quirk
|
|
AGP for example doesn't have a dma_address array.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210614110517.1624-1-christian.koenig@amd.com
|
|
In order to avoid a race condition for user events when changing
cpu affinity reset the active flag only when EOI-ing the event.
This is working fine as all user events are lateeoi events. Note that
lateeoi_ack_mask_dynirq() is not modified as there is no explicit call
to xen_irq_lateeoi() expected later.
Cc: stable@vger.kernel.org
Reported-by: Julien Grall <julien@xen.org>
Fixes: b6622798bc50b62 ("xen/events: avoid handling the same event on two cpus at the same time")
Tested-by: Julien Grall <julien@xen.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrvsky@oracle.com>
Link: https://lore.kernel.org/r/20210623130913.9405-1-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A couple of small, driver specific fixes that arrived in the past few
weeks"
* tag 'spi-fix-v5.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-nxp-fspi: move the register operation after the clock enable
spi: tegra20-slink: Ensure SPI controller reset is deasserted
|
|
The function software_node_notify() - the function that creates
and removes the symlinks between the node and the device - was
called unconditionally in device_add_software_node() and
device_remove_software_node(), but it needs to be called in
those functions only in the special case where the node is
added to a device that has already been registered.
This fixes NULL pointer dereference that happens if
device_remove_software_node() is used with device that was
never registered.
Fixes: b622b24519f5 ("software node: Allow node addition to already existing device")
Reported-and-tested-by: Dominik Brodowski <linux@dominikbrodowski.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
While the disk state has nothing to do with partitions, BLKRRPART is used
to force a full revalidate after things like a disk format for historical
reasons. Restore that behavior.
Link: https://lore.kernel.org/r/20210617115504.1732350-1-hch@lst.de
Fixes: 471bd0af544b ("sd: use bdev_check_media_change")
Reported-by: Xiang Chen <chenxiang66@hisilicon.com>
Tested-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When the call to platform_get_irq() to obtain the IRQ of the lcd fails, the
returned error code should be propagated. However, we currently do not
explicitly assign this error code to 'ret'. As a result, 0 was incorrectly
returned.
Fixes: 7f7b96a8a0a1 ("drm/kmb: Add support for KeemBay Display")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210513134639.6541-1-thunder.leizhen@huawei.com
|
|
Revert commit 4514d991d992 ("PCI: PM: Do not read power state in
pci_enable_device_flags()") that is reported to cause PCI device
initialization issues on some systems.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=213481
Link: https://lore.kernel.org/linux-acpi/YNDoGICcg0V8HhpQ@eldamar.lan
Reported-by: Michael <phyre@rogers.com>
Reported-by: Salvatore Bonaccorso <carnil@debian.org>
Fixes: 4514d991d992 ("PCI: PM: Do not read power state in pci_enable_device_flags()")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We actually need to wait for the moving fence after pinning
the BO to make sure that the pin is completed.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
References: https://lore.kernel.org/dri-devel/20210621151758.2347474-1-daniel.vetter@ffwll.ch/
CC: stable@kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20210622114506.106349-3-christian.koenig@amd.com
|
|
We actually need to wait for the moving fence after pinning
the BO to make sure that the pin is completed.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
References: https://lore.kernel.org/dri-devel/20210621151758.2347474-1-daniel.vetter@ffwll.ch/
CC: stable@kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20210622114506.106349-2-christian.koenig@amd.com
|
|
We actually need to wait for the moving fence after pinning
the BO to make sure that the pin is completed.
v2: grab the lock while waiting
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
References: https://lore.kernel.org/dri-devel/20210621151758.2347474-1-daniel.vetter@ffwll.ch/
CC: stable@kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20210622114506.106349-1-christian.koenig@amd.com
|
|
This reverts commit 1815d9c86e3090477fbde066ff314a7e9721ee0f.
Unfortunately this inverts the locking hierarchy, so back to the
drawing board. Full lockdep splat below:
======================================================
WARNING: possible circular locking dependency detected
5.13.0-rc7-CI-CI_DRM_10254+ #1 Not tainted
------------------------------------------------------
kms_frontbuffer/1087 is trying to acquire lock:
ffff88810dcd01a8 (&dev->master_mutex){+.+.}-{3:3}, at: drm_is_current_master+0x1b/0x40
but task is already holding lock:
ffff88810dcd0488 (&dev->mode_config.mutex){+.+.}-{3:3}, at: drm_mode_getconnector+0x1c6/0x4a0
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (&dev->mode_config.mutex){+.+.}-{3:3}:
__mutex_lock+0xab/0x970
drm_client_modeset_probe+0x22e/0xca0
__drm_fb_helper_initial_config_and_unlock+0x42/0x540
intel_fbdev_initial_config+0xf/0x20 [i915]
async_run_entry_fn+0x28/0x130
process_one_work+0x26d/0x5c0
worker_thread+0x37/0x380
kthread+0x144/0x170
ret_from_fork+0x1f/0x30
-> #1 (&client->modeset_mutex){+.+.}-{3:3}:
__mutex_lock+0xab/0x970
drm_client_modeset_commit_locked+0x1c/0x180
drm_client_modeset_commit+0x1c/0x40
__drm_fb_helper_restore_fbdev_mode_unlocked+0x88/0xb0
drm_fb_helper_set_par+0x34/0x40
intel_fbdev_set_par+0x11/0x40 [i915]
fbcon_init+0x270/0x4f0
visual_init+0xc6/0x130
do_bind_con_driver+0x1e5/0x2d0
do_take_over_console+0x10e/0x180
do_fbcon_takeover+0x53/0xb0
register_framebuffer+0x22d/0x310
__drm_fb_helper_initial_config_and_unlock+0x36c/0x540
intel_fbdev_initial_config+0xf/0x20 [i915]
async_run_entry_fn+0x28/0x130
process_one_work+0x26d/0x5c0
worker_thread+0x37/0x380
kthread+0x144/0x170
ret_from_fork+0x1f/0x30
-> #0 (&dev->master_mutex){+.+.}-{3:3}:
__lock_acquire+0x151e/0x2590
lock_acquire+0xd1/0x3d0
__mutex_lock+0xab/0x970
drm_is_current_master+0x1b/0x40
drm_mode_getconnector+0x37e/0x4a0
drm_ioctl_kernel+0xa8/0xf0
drm_ioctl+0x1e8/0x390
__x64_sys_ioctl+0x6a/0xa0
do_syscall_64+0x39/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
other info that might help us debug this:
Chain exists of: &dev->master_mutex --> &client->modeset_mutex --> &dev->mode_config.mutex
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&dev->mode_config.mutex);
lock(&client->modeset_mutex);
lock(&dev->mode_config.mutex);
lock(&dev->master_mutex);
*** DEADLOCK ***
1 lock held by kms_frontbuffer/1087:
#0: ffff88810dcd0488 (&dev->mode_config.mutex){+.+.}-{3:3}, at: drm_mode_getconnector+0x1c6/0x4a0
stack backtrace:
CPU: 7 PID: 1087 Comm: kms_frontbuffer Not tainted 5.13.0-rc7-CI-CI_DRM_10254+ #1
Hardware name: Intel Corporation Ice Lake Client Platform/IceLake U DDR4 SODIMM PD RVP TLC, BIOS ICLSFWR1.R00.3234.A01.1906141750 06/14/2019
Call Trace:
dump_stack+0x7f/0xad
check_noncircular+0x12e/0x150
__lock_acquire+0x151e/0x2590
lock_acquire+0xd1/0x3d0
__mutex_lock+0xab/0x970
drm_is_current_master+0x1b/0x40
drm_mode_getconnector+0x37e/0x4a0
drm_ioctl_kernel+0xa8/0xf0
drm_ioctl+0x1e8/0x390
__x64_sys_ioctl+0x6a/0xa0
do_syscall_64+0x39/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
Note that this broke the intel-gfx CI pretty much across the board
because it has to reboot machines after it hits a lockdep splat.
Testcase: igt/debugfs_test/read_all_entries
Acked-by: Petri Latvala <petri.latvala@intel.com>
Fixes: 1815d9c86e30 ("drm: add a locked version of drm_is_current_master")
Cc: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210622075409.2673805-1-daniel.vetter@ffwll.ch
|
|
When userspace requests a GPIO v1 line info changed event,
lineinfo_watch_read() populates and returns the gpioline_info_changed
structure. It contains 5 words of padding at the end which are not
initialized before being returned to userspace.
Zero the structure in gpio_v2_line_info_change_to_v1() before populating
its contents.
Fixes: aad955842d1c ("gpiolib: cdev: support GPIO_V2_GET_LINEINFO_IOCTL and GPIO_V2_GET_LINEINFO_WATCH_IOCTL")
Signed-off-by: Gabriel Knezek <gabeknez@linux.microsoft.com>
Reviewed-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
This reverts commit 4cbbe34807938e6e494e535a68d5ff64edac3f20.
Reason for revert: side effect of enlarging CP_MEC_DOORBELL_RANGE may
cause some APUs fail to enter gfxoff in certain user cases.
Signed-off-by: Yifan Zhang <yifan1.zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
doorbell."
This reverts commit 1c0b0efd148d5b24c4932ddb3fa03c8edd6097b3.
Reason for revert: Side effect of enlarging CP_MEC_DOORBELL_RANGE may
cause some APUs fail to enter gfxoff in certain user cases.
Signed-off-by: Yifan Zhang <yifan1.zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Once drm_framebuffer_init has returned 0, the framebuffer is hooked up
to the reference counting machinery and can no longer be destroyed with
a simple kfree. Therefore, it must be called last.
If drm_framebuffer_init returns 0 but its caller then returns non-0,
there will likely be memory corruption fireworks down the road.
The following lead me to this fix:
[ 12.891228] kernel BUG at lib/list_debug.c:25!
[...]
[ 12.891263] RIP: 0010:__list_add_valid+0x4b/0x70
[...]
[ 12.891324] Call Trace:
[ 12.891330] drm_framebuffer_init+0xb5/0x100 [drm]
[ 12.891378] amdgpu_display_gem_fb_verify_and_init+0x47/0x120 [amdgpu]
[ 12.891592] ? amdgpu_display_user_framebuffer_create+0x10d/0x1f0 [amdgpu]
[ 12.891794] amdgpu_display_user_framebuffer_create+0x126/0x1f0 [amdgpu]
[ 12.891995] drm_internal_framebuffer_create+0x378/0x3f0 [drm]
[ 12.892036] ? drm_internal_framebuffer_create+0x3f0/0x3f0 [drm]
[ 12.892075] drm_mode_addfb2+0x34/0xd0 [drm]
[ 12.892115] ? drm_internal_framebuffer_create+0x3f0/0x3f0 [drm]
[ 12.892153] drm_ioctl_kernel+0xe2/0x150 [drm]
[ 12.892193] drm_ioctl+0x3da/0x460 [drm]
[ 12.892232] ? drm_internal_framebuffer_create+0x3f0/0x3f0 [drm]
[ 12.892274] amdgpu_drm_ioctl+0x43/0x80 [amdgpu]
[ 12.892475] __se_sys_ioctl+0x72/0xc0
[ 12.892483] do_syscall_64+0x33/0x40
[ 12.892491] entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes: f258907fdd835e "drm/amdgpu: Verify bo size can fit framebuffer size on init."
Signed-off-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
A disabled/masked interrupt marked as wakeup source must be re-enable
and unmasked in order to be able to wake-up the host. That can be done
by flaging the irqchip with IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND.
Note: It 'sometimes' works without that change, but only thanks to the
lazy generic interrupt disabling (keeping interrupt unmasked).
Reported-by: Michal Koziel <michal.koziel@emlogic.no>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
While checking the master status of the DRM file in
drm_is_current_master(), the device's master mutex should be
held. Without the mutex, the pointer fpriv->master may be freed
concurrently by another process calling drm_setmaster_ioctl(). This
could lead to use-after-free errors when the pointer is subsequently
dereferenced in drm_lease_owner().
The callers of drm_is_current_master() from drm_auth.c hold the
device's master mutex, but external callers do not. Hence, we implement
drm_is_current_master_locked() to be used within drm_auth.c, and
modify drm_is_current_master() to grab the device's master mutex
before checking the master status.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210620110327.4964-2-desmondcheongzx@gmail.com
|
|
The mdev remove callback for the vfio_ap device driver bails out with
-EBUSY if the mdev is in use by a KVM guest (i.e., the KVM pointer in the
struct ap_matrix_mdev is not NULL). The intended purpose was
to prevent the mdev from being removed while in use. There are two
problems with this scenario:
1. Returning a non-zero return code from the remove callback does not
prevent the removal of the mdev.
2. The KVM pointer in the struct ap_matrix_mdev will always be NULL because
the remove callback will not get invoked until the mdev fd is closed.
When the mdev fd is closed, the mdev release callback is invoked and
clears the KVM pointer from the struct ap_matrix_mdev.
Let's go ahead and remove the check for KVM in the remove callback and
allow the cleanup of mdev resources to proceed.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20210609224634.575156-2-akrowiak@linux.ibm.com
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
We need to add a check for if the kzalloc() fails.
Fixes: 4a7695429ead ("i2c: cp2615: add i2c driver for Silicon Labs' CP2615 Digital Audio Bridge")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Bence Csókás <bence98@sch.bme.hu>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
