| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-02-09
This series contains updates to i40e and i40evf only.
Rickard Strandqvist removes an unused function for i40e.
John Linville reorders a piece of code so that y_budget does not get used
by the FCoE code before it gets initialized.
Mitch adds a delay after VF reset with a minimum of 10ms to allow the
hardware internal FIFOs to flush. Bumps up the ARQ descriptors, since
we can easily overrun the PF's admin receive queue. Added locking around
the VF reset code, since during VF deallocation, we cannot depend on
simply masking the interrupt since this does not lock out the service task,
which can still call the reset routine. Fix a potential multi-minute
delay on driver unload, VF disable or system shutdown. When the module
is being unloaded, waiting for the PF to politely handle all of our admin
queue requests might take forever with a lot of VFs enabled, so just
stop everything and request a VF reset. Also stops the watchdog during
shutdown to prevent a log full of admin queue errors and the occasional
hang when the system is shut down.
Anjali forces Tx descriptor writebacks on ITR by kicking off the SWINT
interrupt since we noticed that there are non-cache-aligned Tx
descriptors waiting in the ring while interrupts are disabled under NAPI.
Enables loopback for the FCoE VSI, so that VSIs can directly talk to each
other without going out on the wire.
Matthew fixes an LED blink issue by making sure to clear the GPIO blink
field, instead of OR'ing against zero if the field is already '1'.
Greg cleans up a function header comment.
Vasu helps biosdevname user tool to differentiate dev_port for PCoE netdev
and PF netdev, by setting different dev_port value for FCoE netdev.
Carolyn adds a call to u64_stats_init to the receive setup in order to
avoid lockdep errors with seqcount on newer kernels.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The vunmap() function performs also input parameter validation.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support to get option/expansion rom version flashed in the adapter via
ethtool getdrvinfo function.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver exposes interfaces that directly relate to HW state. Upon fatal
error, consumers of these interfaces (ULPs) that rely on completion of
all their posted work-request could hang, thereby introducing dependencies
in shutdown order. To prevent this from happening, we manage the
relevant resources (CQs, QPs) that are used by the device. Upon a fatal error,
we now generate simulated completions for outstanding WQEs that were not
completed at the time the HW was reset.
It includes invoking the completion event handler for all involved CQs so that
the ULPs will poll those CQs. When polled we return simulated CQEs with
IB_WC_WR_FLUSH_ERR return code enabling ULPs to clean up their resources and
not wait forever for completions upon receiving remove_one.
The above change requires an extra check in the data path to make sure that when
device is in error state, the simulated CQEs will be returned and no further
WQEs will be posted.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When attaching a QP to a multicast address in bonded mode, there was an
assumption that the port of the QP must be #1. This assumption isn't the
case under the flow which enables maximal usage of the physical ports.
Fix it by always checking the port of the original flow and create the
mirrored flow on the other port.
Fixes: c6215745b66a ('IB/mlx4: Load balance ports in port aggregation mode')
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When queuing work to send the NETDEV_BONDING_INFO netdev event, it's
possible that when the work is executed, the pointer to the slave
becomes invalid. This can happen if between queuing the event and the
execution of the work, the net-device was un-ensvaled and re-enslaved.
Fix that by queuing a work with the data of the slave instead of the
slave structure.
Fixes: 69e6113343cf ('net/bonding: Notify state change on slaves')
Reported-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Major changes:
iwlwifi:
* more work for new devices (4165 / 8260)
* cleanups / improvemnts in rate control
* fixes for TDLS
* major statistics work from Johannes - more to come
* improvements for the fw error dump infrastructure
* usual amount of small fixes here and there (scan, D0i3 etc...)
* add support for beamforming
* enable stuck queue detection for iwlmvm
* a few fixes for EBS scan
* fixes for various failure paths
* improvements for TDLS Offchannel
wil6210:
* performance tuning
* some AP features
brcm80211:
* rework some code in SDIO part of the brcmfmac driver related to
suspend/resume that were found doing stress testing
* in PCIe part scheduling of worker thread needed to be relaxed
* minor fixes and exposing firmware revision information to
user-space, ie. ethtool.
mwifiex:
* enhancements for change virtual interface handling
* remove coupling between netdev and FW supported interface
combination, now conversion from any type of supported interface
types to any other type is possible
* DFS support in AP mode
ath9k:
* fix calibration issues on some boards
* Wake-on-WLAN improvements
ath10k:
* add support for qca6174 hardware
* enable RX batching to reduce CPU load
Conflicts:
drivers/net/wireless/rtlwifi/pci.c
Conflict resolution is to get rid of the 'end' label and keep
the rest.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a call to u64_stats_init to Rx setup.
This done in order to avoid lockdep errors with seqcount on newer kernels.
Change-ID: Ia8ba8f0bcbd1c0e926f97d70aeee4ce4fd055e93
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
For all VSIs on a VEB, Loopback mode should be either on or off.
Our configuration requires them to be ON so that VSIs can directly
talk to each other without going out on the wire.
Change-ID: I77b8310bc846329972b13b185949ab1431a46c30
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Set different dev_port value 1 for FCoE netdev than the default zero
dev_port value for PF netdev, this helps biosdevname user tool to
differentiate them correctly while both attached to the same PCI
function.
Change-ID: I8fb90e4ef52a1242f7580e49a3f0918735aee8ef
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
s/enable/disable
Change-ID: Ic0572a6c59d03e05a0a35d2e2e9d532e0512638d
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Make sure to clear the GPIO blink field, instead of OR'ing against zero
if the field is already '1'.
Change-ID: Ie52a52abd48f6f52b20778a6b8b0c542dfc9245c
Signed-off-by: Matt Jared <matthew.a.jared@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch forces Tx descriptor writebacks on ITR by kicking
off the SWINT interrupt when we notice that there are non-cache-aligned
Tx descriptors waiting in the ring while interrupts are disabled
under NAPI.
Change-ID: dd6d9675629bf266c7515ad7a201394618c35444
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Stop the service task in the shutdown handler, preventing it from
accessing the admin queue after it had been closed. This fixes a panic
that could occur when the system was shut down with a lot of VFs
enabled.
Change-ID: I286735e3842de472385bbf7ad68d30331e508add
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Handle clip_tbl debugfs entry, when clip_tbl isn't allocated.
In commit b5a02f503caa0837 ("cxgb4: Update ipv6 address handling api") wrong
argument was passed for single_open for clip_tbl debugfs entry, which led to
below trace. Fixing it.
======
call Trace:
[<ffffffffa073c606>] clip_tbl_open+0x16/0x30 [cxgb4]
[<ffffffff8119e2fa>] do_dentry_open+0x21a/0x370
[<ffffffff8119e499>] vfs_open+0x49/0x50
[<ffffffff811b0d0e>] do_last+0x21e/0x800
[<ffffffff811b1382>] path_openat+0x92/0x470
[<ffffffff8110569f>] ? rb_reserve_next_event+0xaf/0x380
[<ffffffff8110569f>] ? rb_reserve_next_event+0xaf/0x380
[<ffffffff811b189a>] do_filp_open+0x4a/0xa0
[<ffffffff811bdc5d>] ? __alloc_fd+0xcd/0x140
[<ffffffff8119fa4a>] do_sys_open+0x11a/0x230
[<ffffffff8101219f>] ? syscall_trace_enter_phase2+0xaf/0x1b0
[<ffffffff8119fb9e>] SyS_open+0x1e/0x20
[<ffffffff815bf6f0>] tracesys_phase2+0xd4/0xd9
Code: 89 e5 66 66 66 66 90 48 8b 47 e0 48 8b 40 30 48 8b 40 58 c9 c3 66 0f 1f
84 00 00 00 00 00 55 48 89 e5 66 66 66 66 90 48 8b 47 e0 <48> 8b 40 58 c9 c3 66
66 66 66 2e 0f 1f 84 00 00 00 00 00 55 48
RIP [<ffffffff8120898d>] PDE_DATA+0xd/0x20
RSP <ffff8800b08c3c48>
CR2: 0000000000000058
=====
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stop the watchdog during shutdown. Failing to do this causes a log full
of admin queue errors and the occasional hang when the system is shut
down.
Change-ID: Ib2fd11213cca2fa589eb68577e86b1000c23c250
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Occasionally on shutdown, the FW will hand us a bunch of messages filled
with zeros, which can cause us to spin trying to handle them. Just
ignore these and get on with shutting down.
Change-ID: I347e9648f7153ad5a7b7e0847b87f7aad5f3e0da
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When the module is being unloaded, don't wait for the PF to politely
handle all of our admin queue requests, as that might take forever with
a lot of VFs enabled. Instead, just stop everything and request a VF
reset.
When the original shutdown code was written, VF resets were unreliable,
so we avoided them. But with production hardware and firmware, and the
1.x PF driver, this is no longer the case.
This fixes a potential multi-minute delay on driver unload, VF disable,
or system shutdown.
Change-ID: Ib43d6d860ef6b9b8f26e8dce0615a0302608c7d9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
During VF deallocation, we need to lock out the VF reset code. However,
we cannot depend on simply masking the interrupt, as this does not lock
out the service task, which can still call the reset routine. Instead,
leave the interrupt enabled, but add locking around the VF disable and
reset routines.
For the disable code, we wait to get the lock, as the reset code will
take a finite amount of time to run. For the reset code, we just return
if we fail to get the lock. Since we know that the VFs are being
disabled, we don't need to handle the reset.
This fixes a panic when disabling SR-IOV.
Change-ID: Iea0a6cdef35c331f48c6d5b2f8e6f0e86322e7d8
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When enabling 64 VFs and loading the VF driver in the host kernel, we
can easily overrun the PF's admin receive queue. Double the size of this
queue, and increase the work limit to allow the PF to handle more
requests in a single pass through the service task.
Change-ID: I0efbbdc61954bffad422a2f33c4b948a59370bf5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Delay a minimum of 10ms after VF reset, to allow the hardware's internal
FIFOs to flush.
Change-ID: I8a02ddb28c9f0d7303a1eb21d0b2443e5b4c1cda
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This I40E_FCOE block increments v_budget before it has been initialized,
then v_budget gets overwritten a few lines later. This patch just
reorders the code hunks in what I believe was the intended sequence.
Coverity: CID 1260099
Signed-off-by: John W Linville <linville@tuxdriver.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Remove the function i40e_rx_is_fip() that is not used anywhere.
This was partially found by using a static code analysis program
called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
src_ip is a pointer to a union vxlan_addr, one member of which is a
struct sockaddr. Passing a pointer to src_ip is wrong; one should pass
the value of src_ip itself. Since %pIS formally expects something of
type struct sockaddr*, let's pass a pointer to the appropriate union
member, though this of course doesn't change the generated code.
Fixes: e4c7ed415387 ("vxlan: add ipv6 support")
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hex constant chosen for VMXNET3_REV1_MAGIC is offensive,
replace it with its decimal equivalent.
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Reviewed-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Receive Flow Steering is a nice solution but suffers from
hash collisions when a mix of connected and unconnected traffic
is received on the host, when flow hash table is populated.
Also, clearing flow in inet_release() makes RFS not very good
for short lived flows, as many packets can follow close().
(FIN , ACK packets, ...)
This patch extends the information stored into global hash table
to not only include cpu number, but upper part of the hash value.
I use a 32bit value, and dynamically split it in two parts.
For host with less than 64 possible cpus, this gives 6 bits for the
cpu number, and 26 (32-6) bits for the upper part of the hash.
Since hash bucket selection use low order bits of the hash, we have
a full hash match, if /proc/sys/net/core/rps_sock_flow_entries is big
enough.
If the hash found in flow table does not match, we fallback to RPS (if
it is enabled for the rxqueue).
This means that a packet for an non connected flow can avoid the
IPI through a unrelated/victim CPU.
This also means we no longer have to clear the table at socket
close time, and this helps short lived flows performance.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dump Transport Processor modules congestion control configuration
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support to dump the current contents of mailbox and the driver which owns
it.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dump Upper Layer Protocol RX module command trace
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dump Transport Processor event trace.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dump out various chip sensor information. Currently Chip Temperature
and Core Voltage.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 32-bit fields of a tx-wrb are little endian. The driver is currently
using be_dws_le_to_cpu() routine to swap (cpu to le) all the fields of
a tx-wrb. So, the rsvd field is also unnecessarily swapped.
This patch fixes this by individually swapping the required fields.
Also, the type of the fields in eth_tx_wrb{} is now changed to __le32
from u32 to avoid sparse warnings.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for processing the port misconfigure async
event generated by the FW. This event is generated typically when an
optical module is incorrectly installed or is faulty.
This patch also moves the port_name field to the adapter struct for
logging the event. As the be_cmd_query_port_name() call is now moved
to be_get_config(), it is modified to use the mailbox instead of MCCQ
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch re-factors the filter setting (uc-list, mc-list, promisc, vlan)
code in be_set_rx_mode() and be_vid_config() to make it more readable
and reduce code duplication.
This patch adds a separate field to track the state/mode of filtering,
along with moving all the filtering related fields to one place in be
be_adapter structure.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch passes BE_IF_FLAGS_XXX flags to be_cmd_rx_filter() routine
instead of the IFF_XXX flags. Doing this gets rid of the code to convert
the IFF_XXX flags to the BE_IF_FLAGS_XXX used by the FW cmd. The patch
also removes code for setting if_flags_mask that was duplicated for each
filter mode.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While sending FW update cmds to the FW, the driver specifies the "type"
of each component that needs to be flashed. The FW then picks the offset
in the flash area at which the componnet is to be flashed. This doesn't work
when new components that the current FW doesn't recognize, need to be
flashed. Recent FWs (10.2 and above) support a scheme of FW-update wherein
the "offset" of the component in the flash area can be specified instead
of the "type". This patch uses the "offset" based FW-update mechanism and
only when it fails, it fallsback to the old "type" based update.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Skyhawk-B0 FW UFI is not compatible to flash on Skyhawk-P2 ASIC.
But, Skyhawk-P2 FW UFI is compatible with both B0 and P2 chips.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch re-factors the code that checks for flash file compatibility with
the chip type, for better readability, as follows:
- be_get_ufi_type() returns the UFI type from the flash file
- be_check_ufi_compatibility() checks if the UFI type is compatible
with the adapter/chip that is being flashed
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BIT(x) is the preffered usage.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Routines that are called only inside one src file must remain in that
file itself. Including them in a header file that is used for exporting
routine/struct definitions, causes unnecessary compilation of other
src files, when such a routine is modified.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-02-05
This series contains updates to fm10k, ixgbe and ixgbevf.
Matthew fixes an issue where fm10k does not properly drop the upper-most four
bits on of the VLAN ID due to type promotion, so resolve the issue by not
masking off the bits, but by throwing an error if the VLAN ID is out-of-bounds.
Then cleans up two cases where variables were not being used, but were
being set, so just remove the unused variables.
Don cleans up sparse errors in the x550 family file for ixgbe. Fixed up
a redundant setting of the default value for set_rxpba, which was done
twice accidentally. Cleaned up the probe routine to remove a redundant
attempt to identify the PHY, which could lead to a panic on x550. Added
support for VXLAN receive checksum offload in x550 hardware. Added the
Ethertype Anti-spoofing feature for affected devices.
Emil enables ixgbe and ixgbevf to allow multiple queues in SRIOV mode.
Adds RSS support for x550 per VF. Fixed up a couple of issues introduced
in commit 2b509c0cd292 ("ixgbe: cleanup ixgbe_ndo_set_vf_vlan"), fixed
setting of the VLAN inside ixgbe_enable_port_vlan() and disable the
"hide VLAN" bit in PFQDE when port VLAN is disabled. Cleaned up the
setting of vlan_features by enabling all features at once. Fixed the
ordering of the shutdown patch so that we attempt to shutdown the rings
more gracefully. We shutdown the main Rx filter in the case of Rx and we
set the carrier_off state in the case of Tx so that packets stop being
delivered from outside the driver. Then we shutdown interrupts and NAPI,
then finally stop the rings from performing DMA and clean them. Added
code to allow for Tx hang checking to provide more robust debug info in
the event of a transmit unit hang in ixgbevf. Cleaned up ixgbevf logic
dealing with link up/down by breaking down the link detection and up/down
events into separate functions, similar to how these events are handled
in other drivers. Combined the ixgbevf reset and watchdog tasks into a
single task so that we can avoid multiple schedules of the reset task when
we have a reset event needed due to either the mailbox going down or
transmit packets being present on a link down.
v2: Fixed up patch #03 of the series to remove the variable type change
based on feedback from David Laight
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use BIT macro to replace (1 << bits).
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vlan_get_protocol() has been defined and use it to replace
get_protocol().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Keep NETIF_F_HW_VLAN_CTAG_RX and NETIF_F_HW_VLAN_CTAG_TX at the
same line.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is unnecessary to accress the hw register if the device is unplugged.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace (tp->speed & LINK_STATUS) with netif_carrier_ok().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set LPM timer to 500us, except for RTL_VER_04 which doesn't link at
USB 3.0.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a error occurs when submitting rx, skip the remaining submissions
and try to submit them again next time.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using per channel DMA interrupts the transmit interrupt (TI) and the
receive interrupt (RI) are masked off so as to not generate an interrupt
to the main ISR. However, should another interrupt fire for the DMA channel
that is handled by the main ISR the TI/RI bits can still be set. This
will cause the wrong and uninitialized napi structure to be used causing a
panic. Add a check to be sure per channel DMA interrupts are not enabled
before acting on those bit flags.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
