| Age | Commit message (Collapse) | Author |
|---|
|
Data read direct from device tree properties will be in the device
tree's native endianness (i.e., big-endian).
This patch uses of_property_read_u32() to read the bus-width
property in host byte order instead.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Rework the locking and lifecycle management in the cdc-acm driver.
Instead of using a global mutex to prevent the 'acm' object from being
freed, use the tty_port kref to keep the device alive when either the
USB side or TTY side is still active.
This allows us to use the global mutex purely for protecting the
acm_table, while use acm->mutex to guard against disconnect during
TTY port activation and shutdown.
The USB-side kref is taken during port initialization in probe(), and
released at the end of disconnect(). The TTY-side kref is taken in
install() and released in cleanup(). On disconnect, tty_vhangup() is
called instead of tty_hangup() to ensure the TTY hangup processing is
completed before the USB device is taken down.
The TTY open and close handlers have been gutted and replaced with
tty_port_open() and tty_port_close() respectively. The driver-specific
code which used to be there was spread across install(), activate() and
shutdown().
Reported-by: Dave Jones <davej@redhat.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geoff/ps3-linux into usb-next
* 'for-usb' of git://git.kernel.org/pub/scm/linux/kernel/git/geoff/ps3-linux:
usb: PS3 EHCI QH read work-around
usb: Fix PS3 EHCI suspend
usb: PS3 EHCI HC reset work-around
usb: Remove ehci_reset call from ehci_run
|
|
This lets us handle the PS3 merge easier, as well as syncing up with
other USB fixes already in the -rc4 tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
PS3 EHCI HC errata fix 244. The SCC EHCI HC will not correctly perform QH
reads that occur near or span a micro-frame boundry. This is due to a problem
in the Nak Count Reload Control logic (EHCI Specification 1.0 Section 4.9.1).
The work-around for this problem is for the HC driver to set I=1 (inactive) for
QHs with H=1 (list head).
Signed-off-by: Geoff Levand <geoff@infradead.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
|
|
The EHCI USB controller of the Cell Super Companion Chip used in the PS3
will stop the root hub after all root hub ports are suspended. When in
this condition the ehci-hcd handshake routine will return -ETIMEDOUT and
the USB runtime suspend sequence will fail. The STS_HLT bit will not be
set, so inspection of the frame index is used to test for the condition.
Add a new routine handshake_for_broken_root_hub() that is called after
an unsuccessful -ETIMEDOUT handshake. On PS3 handshake_for_broken_root_hub()
will test for the condition, and if found will return success to allow the
USB suspend to complete. For all other platforms
handshake_for_broken_root_hub() will return -ETIMEDOUT
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
|
|
PS3 EHCI HC errata fix 316 - The PS3 EHCI HC will reset its
internal INSNREGXX setup regs back to the chip default values
on Host Controller Reset (CMD_RESET) or Light Host Controller
Reset (CMD_LRESET). The work-around for this is for the HC
driver to re-initialise these regs when ever the HC is reset.
Adds a new helper routine ps3_ehci_setup_insnreg() which is
called from ps3_ehci_hc_reset().
Signed-off-by: Geoff Levand <geoff@infradead.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
|
|
Remove the ehci_reset() call done in the ehci_run() routine of the
USB EHCI host controller driver and add an ehci_reset() call to the
probe processing of all EHCI platform drivers that do not already call
ehci_reset().
The call to ehci_reset() from ehci_run() was problematic for several
platform drivers, and unnecessary for others. This change moves the
decision to call ehci_reset() at driver startup to the platform
driver code.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
|
|
http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
* 'fixes' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
ARM: 7182/1: ARM cpu topology: fix warning
ARM: 7181/1: Restrict kprobes probing SWP instructions to ARMv5 and below
ARM: 7180/1: Change kprobes testcase with unpredictable STRD instruction
ARM: 7177/1: GIC: avoid skipping non-existent PPIs in irq_start calculation
ARM: 7176/1: cpu_pm: register GIC PM notifier only once
ARM: 7175/1: add subname parameter to mfp_set_groupg callers
ARM: 7174/1: Fix build error in kprobes test code on Thumb2 kernels
ARM: 7172/1: dma: Drop GFP_COMP for DMA memory allocations
ARM: 7171/1: unwind: add unwind directives to bitops assembly macros
ARM: 7170/2: fix compilation breakage in entry-armv.S
ARM: 7168/1: use cache type functions for arch_get_unmapped_area
ARM: perf: check that we have a platform device when reserving PMU
ARM: 7166/1: Use PMD_SHIFT instead of PGDIR_SHIFT in dma-consistent.c
ARM: 7165/2: PL330: Fix typo in _prepare_ccr()
ARM: 7163/2: PL330: Only register usable channels
ARM: 7162/1: errata: tidy up Kconfig options for PL310 errata workarounds
ARM: 7161/1: errata: no automatic store buffer drain
ARM: perf: initialise used_mask for fake PMU during validation
ARM: PMU: remove pmu_init declaration
ARM: PMU: re-export release_pmu symbol to modules
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB: Fix RCU lockdep splats
IB/ipoib: Prevent hung task or softlockup processing multicast response
IB/qib: Fix over-scheduling of QSFP work
RDMA/cxgb4: Fix retry with MPAv1 logic for MPAv2
RDMA/cxgb4: Fix iw_cxgb4 count_rcqes() logic
IB/qib: Don't use schedule_work()
|
|
* 'dt-for-linus' of git://sources.calxeda.com/kernel/linux:
of: Add Silicon Image vendor prefix
of/irq: of_irq_init: add check for parent equal to child node
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: twl: fix twl4030 support for smps regulators
regulator: fix use after free bug
regulator: aat2870: Fix the logic of checking if no id is matched in aat2870_get_regulator
|
|
This patch adds power management support such as suspend and resume
functions.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
|
|
Commit f2c31e32b37 ("net: fix NULL dereferences in check_peer_redir()")
forgot to take care of infiniband uses of dst neighbours.
Many thanks to Marc Aurele who provided a nice bug report and feedback.
Reported-by: Marc Aurele La France <tsi@ualberta.ca>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
This following can occur with ipoib when processing a multicast reponse:
BUG: soft lockup - CPU#0 stuck for 67s! [ib_mad1:982]
Modules linked in: ...
CPU 0:
Modules linked in: ...
Pid: 982, comm: ib_mad1 Not tainted 2.6.32-131.0.15.el6.x86_64 #1 ProLiant DL160 G5
RIP: 0010:[<ffffffff814ddb27>] [<ffffffff814ddb27>] _spin_unlock_irqrestore+0x17/0x20
RSP: 0018:ffff8802119ed860 EFLAGS: 00000246
0000000000000004 RBX: ffff8802119ed860 RCX: 000000000000a299
RDX: ffff88021086c700 RSI: 0000000000000246 RDI: 0000000000000246
RBP: ffffffff8100bc8e R08: ffff880210ac229c R09: 0000000000000000
R10: ffff88021278aab8 R11: 0000000000000000 R12: ffff8802119ed860
R13: ffffffff8100be6e R14: 0000000000000001 R15: 0000000000000003
FS: 0000000000000000(0000) GS:ffff880028200000(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 00000000006d4840 CR3: 0000000209aa5000 CR4: 00000000000406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Call Trace:
[<ffffffffa032c247>] ? ipoib_mcast_send+0x157/0x480 [ib_ipoib]
[<ffffffff8100bc8e>] ? apic_timer_interrupt+0xe/0x20
[<ffffffff8100bc8e>] ? apic_timer_interrupt+0xe/0x20
[<ffffffffa03283d4>] ? ipoib_path_lookup+0x124/0x2d0 [ib_ipoib]
[<ffffffffa03286fc>] ? ipoib_start_xmit+0x17c/0x430 [ib_ipoib]
[<ffffffff8141e758>] ? dev_hard_start_xmit+0x2c8/0x3f0
[<ffffffff81439d0a>] ? sch_direct_xmit+0x15a/0x1c0
[<ffffffff81423098>] ? dev_queue_xmit+0x388/0x4d0
[<ffffffffa032d6b7>] ? ipoib_mcast_join_finish+0x2c7/0x510 [ib_ipoib]
[<ffffffffa032dab8>] ? ipoib_mcast_sendonly_join_complete+0x1b8/0x1f0 [ib_ipoib]
[<ffffffffa02a0946>] ? mcast_work_handler+0x1a6/0x710 [ib_sa]
[<ffffffffa015f01e>] ? ib_send_mad+0xfe/0x3c0 [ib_mad]
[<ffffffffa00f6c93>] ? ib_get_cached_lmc+0xa3/0xb0 [ib_core]
[<ffffffffa02a0f9b>] ? join_handler+0xeb/0x200 [ib_sa]
[<ffffffffa029e4fc>] ? ib_sa_mcmember_rec_callback+0x5c/0xa0 [ib_sa]
[<ffffffffa029e79c>] ? recv_handler+0x3c/0x70 [ib_sa]
[<ffffffffa01603a4>] ? ib_mad_completion_handler+0x844/0x9d0 [ib_mad]
[<ffffffffa015fb60>] ? ib_mad_completion_handler+0x0/0x9d0 [ib_mad]
[<ffffffff81088830>] ? worker_thread+0x170/0x2a0
[<ffffffff8108e160>] ? autoremove_wake_function+0x0/0x40
[<ffffffff810886c0>] ? worker_thread+0x0/0x2a0
[<ffffffff8108ddf6>] ? kthread+0x96/0xa0
[<ffffffff8100c1ca>] ? child_rip+0xa/0x20
Coinciding with stack trace is the following message:
ib0: ib_address_create failed
The code below in ipoib_mcast_join_finish() will note the above
failure in the address handle but otherwise continue:
ah = ipoib_create_ah(dev, priv->pd, &av);
if (!ah) {
ipoib_warn(priv, "ib_address_create failed\n");
} else {
The while loop at the bottom of ipoib_mcast_join_finish() will attempt
to send queued multicast packets in mcast->pkt_queue and eventually
end up in ipoib_mcast_send():
if (!mcast->ah) {
if (skb_queue_len(&mcast->pkt_queue) < IPOIB_MAX_MCAST_QUEUE)
skb_queue_tail(&mcast->pkt_queue, skb);
else {
++dev->stats.tx_dropped;
dev_kfree_skb_any(skb);
}
My read is that the code will requeue the packet and return to the
ipoib_mcast_join_finish() while loop and the stage is set for the
"hung" task diagnostic as the while loop never sees a non-NULL ah, and
will do nothing to resolve.
There are GFP_ATOMIC allocates in the provider routines, so this is
possible and should be dealt with.
The test that induced the failure is associated with a host SM on the
same server during a shutdown.
This patch causes ipoib_mcast_join_finish() to exit with an error
which will flush the queued mcast packets. Nothing is done to unwind
the QP attached state so that subsequent sends from above will retry
the join.
Reviewed-by: Ram Vepa <ram.vepa@qlogic.com>
Reviewed-by: Gary Leshner <gary.leshner@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
With the revert of "of/irq: of_irq_find_parent: check for parent equal to
child" (dc9372808412edb), we need another way to handle parent node equal
to the child node. This can simply be handled in of_irq_init by checking
for this condition.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Tested-by: Pawel Moll <pawel.moll@arm.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: convert drivers/hwmon/* to use module_platform_driver()
hwmon: Remove redundant spi driver bus initialization
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
efivars: add missing parameter to efi_pstore_read()
|
|
In the case where CONFIG_PSTORE=n, the function efi_pstore_read() doesn't
have the correct list of parameters. This patch provides a definition
of efi_pstore_read() with 'char **buf' added to fix this warning:
"drivers/firmware/efivars.c:609: warning: initialization from".
problem introduced in commit f6f8285132907757ef84ef8dae0a1244b8cde6ac
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Don't over-schedule QSFP work on driver initialization. It could end
up being run simultaneously on two different CPUs resulting in bad
EEPROM reads. In combination with setting the physical IB link state
prior to the IBC being brought out of reset, this can cause the link
state machine to start training early with wrong settings.
Signed-off-by: Mitko Haralanov <mitko@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Fix logic so that we don't retry with MPAv1 once we have done that
already. Otherwise, we end up retrying with MPAv1 even when its not
needed on getting peer aborts - and this could lead to kernel panic.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Fix another place in the code where logic dealing with the t4_cqe was
using the wrong QID. This fixes the counting logic so that it tests
against the SQ QID instead of the RQ QID when counting RCQES.
Signed-off by: Jonathan Lallinger <jonathan@ogc.us>
Signed-off by: Steve Wise <swise@ogc.us>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
pstore: pass allocated memory region back to caller
|
|
SMPS regulator voltage control differs from the one of the LDO ones.
Current TWL code was using LDO regulator ops for controlling the SMPS
regulators, which fails. This was fixed fixed by adding separate
regulator type which uses correct logic and calculations for the
voltage levels.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
|
|
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/exynos: fixed wrong err ptr usage and destroy call in exeception
drm/exynos: Add disable of manager
drm/exynos: include linux/module.h
drm/exynos: fix vblank bug.
drm/exynos: changed buffer structure.
drm/exynos: removed unnecessary variable.
drm/exynos: use gem create function generically
drm/exynos: checked for null pointer
drm/exynos: added crtc dpms for disable crtc
drm/exynos: removed meaningless parameter from fbdev update
drm/exynos: restored kernel_fb_list when reiniting fb_helper
drm/exynos: changed exynos_drm_display to exynos_drm_display_ops
drm/exynos: added manager object to connector
drm/exynos: fixed converting between display mode and timing
drm/exynos: fixed connector flag with hpd and interlace scan for hdmi
drm/exynos: added kms poll for handling hpd event
|
|
This is caused by dereferencing 'rdev' after device_unregister() in
the regulator_unregister() function. 'rdev' is freed by
device_unregister(), so it must not be dereferenced after this call.
[Edited commit message for legibility -- broonie]
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
git://git.infradead.org/users/kmpark/linux-samsung into drm-fixes
* 'exynos-drm' of git://git.infradead.org/users/kmpark/linux-samsung:
drm/exynos: fixed wrong err ptr usage and destroy call in exeception
drm/exynos: Add disable of manager
drm/exynos: include linux/module.h
drm/exynos: fix vblank bug.
drm/exynos: changed buffer structure.
drm/exynos: removed unnecessary variable.
drm/exynos: use gem create function generically
drm/exynos: checked for null pointer
drm/exynos: added crtc dpms for disable crtc
drm/exynos: removed meaningless parameter from fbdev update
drm/exynos: restored kernel_fb_list when reiniting fb_helper
drm/exynos: changed exynos_drm_display to exynos_drm_display_ops
drm/exynos: added manager object to connector
drm/exynos: fixed converting between display mode and timing
drm/exynos: fixed connector flag with hpd and interlace scan for hdmi
drm/exynos: added kms poll for handling hpd event
|
|
aat2870_get_regulator
In current implementation, the pointer ri is not NULL if no id is matched.
Fix it by checking i == ARRAY_SIZE(aat2870_regulators) if no id is matched.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
|
|
This patch converts the drivers in drivers/usb/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
* 'fbdev-for-linus' of git://github.com/schandinat/linux-2.6:
viafb: correct sync polarity for OLPC DCON
video:da8xx-fb: Disable and reset sequence on version2 of LCDC
OMAPDSS: DISPC: skip scaling calculations when not scaling
OMAPFB: fix compilation warnings due to missing include
OMAPDSS: HDMI: fix returned HDMI pixel clock
|
|
Revert a hunk in drivers/net/wireless/ath/ath9k/hw.c introduced by
commit 2577c6e8f232 ("ath9k_hw: Add support for AR946/8x chipsets") that
caused a nasty regression to appear on my Acer Ferrari One (the box
locks up entirely at random times after the wireless has been started
without any way to get debug information out of it).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This fixes a memory leak reported by Catalin Marinas:
schedule_ptds() is called from isp1760_irq() and removes the qh from the
controlqhs queue but ep->hcpriv still points to the qh and therefore it is not
freed.
Shortly after this, the isp1760_endpoint_disable() function sets ep->hcpriv to
NULL and calls schedule_ptds() but since the corresponding qh is no longer in
the queue, it is simply forgotten and reported by kmemleak.
With this patch, the qh is always freed at endpoint_disable, instead, and the
corresponding entry removed from the queue head list.
While I was at it, I also replaced the lines in isp1760_endpoint_disable()
that removed remaining qtds from the qh with a WARN_ON check for non-empty qh,
in line with earlier comments from Alan Stern (linux-usb list, 2011-07-20).
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Small code refactoring to ease the real fix in patch #2.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
xhci-hub used some numerical values for initialisation of root hub
descriptors. #define values are addded in usb 2.0 hub specification
file and these values are used for root hub characteristics
initialisation.
Also use some #defines in places where magic numbers are being used.
Signed-off-by: Aman Deep <amandeep3986@gmail.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
For OTG controller, the host driver will call function
otg_get_transceiver to get the otg transceiver, so we need to init the
OTG driver before HOST.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Handle null old_termios in ftdi_set_termios() calls from uart_resume_port().
Signed-off-by: Andrew Worsley <amworsley@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The BKL is a gonner.
Signed-off-by: Davidlohr Bueso <dave@gnu.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This pulls in the latest USB bugfixes and helps a few of the drivers
merge nicer in the future due to changes in both branches.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 798681bf "ARM: 7158/1: add new MFP implement for NUC900"
adds subname parameter for mfp_set_groupg.
Thus add subname parameter to the callers.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Fix build failure in staging iio driver:
.../drivers/staging/iio/industrialio-core.c: In function 'iio_event_getfd':
.../drivers/staging/iio/industrialio-core.c:262:32: error:
'ev_int' undeclared (first use in this function)
Also convert the rest of the function to use the new variable.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/44x: Add mtd ndfc to the ppx44x defconfig
powerpc: Fix compiliation with hugetlbfs enabled
arch/powerpc/sysdev/ehv_pic.c: add missing kfree
powerpc/fsl-lbc: Fix for fsl_upm
drivers/edac/mpc85xx_edac.c: fix memory controller compatible for edac
powerpc/qe: Fixup QE_General4 errata
powerpc/85xx: Fix compile error on p3060_qds.c
powerpc/p3060qds: Fix select of 'MPC8xxx_GPIO'
powerpc/p1023: set IRQ[4:6,11] to active-high level sensitive for PCIe
|
|
This patch converts the drivers in drivers/hwmon/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: Donggeun Kim <dg77.kim@samsung.com>
Cc: Simon Guinot <sguinot@lacie.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: J Keerthy <j-keerthy@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
* git://github.com/herbertx/crypto:
crypto: mv_cesa - fix hashing of chunks > 1920 bytes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson
* 'gpio-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
gpio: pca953x: Staticise pca953x_get_altdata()
|
|
In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_register_driver(),
so we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: lm-sensors@lm-sensors.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
compatible in dts has been changed, so the driver needs to be updated
accordingly.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
* git://github.com/rustyrussell/linux:
virtio-pci: make reset operation safer
virtio-mmio: Correct the name of the guest features selector
virtio: add HAS_IOMEM dependency to MMIO platform bus driver
|
|
virtio pci device reset actually just does an I/O
write, which in PCI is really posted, that is it
can complete on CPU before the device has received it.
Further, interrupts might have been pending on
another CPU, so device callback might get invoked after reset.
This conflicts with how drivers use reset, which is typically:
reset
unregister
a callback running after reset completed can race with
unregister, potentially leading to use after free bugs.
Fix by flushing out the write, and flushing pending interrupts.
This assumes that device is never reset from
its vq/config callbacks, or in parallel with being
added/removed, document this assumption.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
Guest features selector spelling mistake.
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
