| Age | Commit message (Collapse) | Author |
|---|
|
[Why]
In USB4 DP tunneling, it's possible to have this scenario that
the path becomes unavailable and CM tears down the path a little bit late.
So, in this case, the HPD is high but fails to read any DPCD register.
That causes the link connection type to be set to sst.
And not all sinks are removed behind the MST branch.
[How]
Restore the link connection type if it fails to read DPCD register.
Cc: stable@vger.kernel.org
Cc: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Cruise Hung <Cruise.Hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Writing to DRR registers such as OTG_V_TOTAL_MIN on the same frame as a
pipe commit can cause underflow.
Cc: stable@vger.kernel.org
Cc: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Hot plugging and then hot unplugging leads to k1 and k2 values to
change, as signal is detected as a virtual signal on hot unplug. Writing
these values to OTG_PIXEL_RATE_DIV register might cause primary display
to blank (known hw bug).
[HOW]
No longer write k1 and k2 values to register if signal is virtual, we
have safe guards in place in the case that k1 and k2 is unassigned so
that an unknown value is not written to the register either.
Cc: stable@vger.kernel.org
Cc: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Saaem Rizvi <SyedSaaem.Rizvi@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The VCN firmware loading path enables the indirect SRAM mode if it's
advertised as supported. We might have some cases of FW issues that
prevents this mode to working properly though, ending-up in a failed
probe. An example below, observed in the Steam Deck:
[...]
[drm] failed to load ucode VCN0_RAM(0x3A)
[drm] psp gfx command LOAD_IP_FW(0x6) failed and response status is (0xFFFF0000)
amdgpu 0000:04:00.0: [drm:amdgpu_ring_test_helper [amdgpu]] *ERROR* ring vcn_dec_0 test failed (-110)
[drm:amdgpu_device_init.cold [amdgpu]] *ERROR* hw_init of IP block <vcn_v3_0> failed -110
amdgpu 0000:04:00.0: amdgpu: amdgpu_device_ip_init failed
amdgpu 0000:04:00.0: amdgpu: Fatal error during GPU init
[...]
Disabling the VCN block circumvents this, but it's a very invasive
workaround that turns off the entire feature. So, let's add a quirk
on VCN loading that checks for known problematic BIOSes on Vangogh,
so we can proactively disable the indirect SRAM mode and allow the
HW proper probe and VCN IP block to work fine.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2385
Fixes: 82132ecc5432 ("drm/amdgpu: enable Vangogh VCN indirect sram mode")
Cc: stable@vger.kernel.org
Cc: James Zhu <James.Zhu@amd.com>
Cc: Leo Liu <leo.liu@amd.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Copy paste error.
Fixes: 384334120b66 ("drm/amdgpu/nv: don't expose AV1 if VCN0 is harvested")
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=4454
Cc: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
When FB_DAMAGE_CLIPS are provided in a non-MPO scenario, the loop does
not use the counter i. This causes the fill_dc_dity_rect() to always
fill dirty_rects[0], causing graphical artifacts when a damage clip
aware DRM client sends more than 1 damage clip.
Instead, use the flip_addrs->dirty_rect_count which is incremented by
fill_dc_dirty_rect() on a successful fill.
Fixes: 30ebe41582d1 ("drm/amd/display: add FB_DAMAGE_CLIPS support")
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2453
Signed-off-by: Benjamin Cheng <ben@bcheng.me>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.x
|
|
Some amd asics having reliable hotplug support don't call
drm_kms_helper_poll_init in driver init sequence. However,
due to the unified suspend/resume path for all asics, because
the output_poll_work->func is not set for these asics, a warning
arrives when suspending.
[ 90.656049] <TASK>
[ 90.656050] ? console_unlock+0x4d/0x100
[ 90.656053] ? __irq_work_queue_local+0x27/0x60
[ 90.656056] ? irq_work_queue+0x2b/0x50
[ 90.656057] ? __wake_up_klogd+0x40/0x60
[ 90.656059] __cancel_work_timer+0xed/0x180
[ 90.656061] drm_kms_helper_poll_disable.cold+0x1f/0x2c [drm_kms_helper]
[ 90.656072] amdgpu_device_suspend+0x81/0x170 [amdgpu]
[ 90.656180] amdgpu_pmops_runtime_suspend+0xb5/0x1b0 [amdgpu]
[ 90.656269] pci_pm_runtime_suspend+0x61/0x1b0
drm_kms_helper_poll_enable/disable is valid when poll_init is called in
amdgpu code, which is only used in non DC path. So move such codes into
non-DC path code to get rid of such warnings.
v1: introduce use_kms_poll flag in amdgpu as the poll stuff check
v2: use dc_enabled as the flag to simply code
v3: move code into non DC path instead of relying on any flag
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2411
Fixes: a4e771729a51 ("drm/probe_helper: sort out poll_running vs poll_enabled")
Reported-by: Bert Karwatzki <spasswolf@web.de>
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Suggested-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why]
On resume some displays are not ready for HDCP, so they will fail if we
start the hdcp authentintication too soon.
Add a delay so that the displays can be ready before we start.
NOTE: Previoulsy this delay was set to 3 seconds but it was causing
issues with compliance, 2 seconds should enough for compliance and the
s3 resume case.
[How]
Change the Delay to 2 seconds.
Reviewed-by: Aurabindo Pillai <Aurabindo.Pillai@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
kgd_mem pointers returned by kfd_process_device_translate_handle are
only guaranteed to be valid while p->mutex is held. As soon as the mutex
is unlocked, another thread can free the BO.
Signed-off-by: Chia-I Wu <olvaffe@gmail.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
for sriov, we added a new flag to indicate av1 support,
this will override the original caps info.
Signed-off-by: Jane Jian <Jane.Jian@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Always setup overdrive tables after resume. Preserve only some
user-defined settings in user_overdrive_table if they're set.
Copy restored user_overdrive_table into od_table to get correct
values.
On cold boot, BTC was triggered and GfxVfCurve was calibrated. We
got VfCurve settings (a). On resuming back, BTC will be triggered
again and GfxVfCurve will be recalibrated. VfCurve settings (b)
got may be different from those of cold boot. So if we reuse
those VfCurve settings (a) got on cold boot on suspend, we can
run into discrepencies.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1897
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2276
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Błażej Szczygieł <mumei6102@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Align the SMU driver interface version with PMFW to
suppress the version mismatch message on driver loading.
Signed-off-by: Tim Huang <tim.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.x
|
|
Set *q to NULL on errors, otherwise pqm_create_queue would free it
again.
Signed-off-by: Chia-I Wu <olvaffe@gmail.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
During miration to vram prange->offset is valid after vram buffer is located,
either use old one or allocate a new one. Move svm_range_vram_node_new before
migrate for each vma to get valid prange->offset.
v2: squash in warning fix
Fixes: b4ee9606378b ("drm/amdkfd: Fix BO offset for multi-VMA page migration")
Signed-off-by: Xiaogang Chen <Xiaogang.Chen@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
svm_migrate_ram_to_vram migrates a prange from sys ram to vram. The prange may
cross multiple vma. Need remember current dst vram offset in the TTM resource for
each migration.
v2: squash in warning fix (Alex)
Signed-off-by: Xiaogang Chen <Xiaogang.Chen@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
AMD has issued an advisory indicating that having fTPM enabled in
BIOS can cause "stuttering" in the OS. This issue has been fixed
in newer versions of the fTPM firmware, but it's up to system
designers to decide whether to distribute it.
This issue has existed for a while, but is more prevalent starting
with kernel 6.1 because commit b006c439d58db ("hwrng: core - start
hwrng kthread also for untrusted sources") started to use the fTPM
for hwrng by default. However, all uses of /dev/hwrng result in
unacceptable stuttering.
So, simply disable registration of the defective hwrng when detecting
these faulty fTPM versions. As this is caused by faulty firmware, it
is plausible that such a problem could also be reproduced by other TPM
interactions, but this hasn't been shown by any user's testing or reports.
It is hypothesized to be triggered more frequently by the use of the RNG
because userspace software will fetch random numbers regularly.
Intentionally continue to register other TPM functionality so that users
that rely upon PCR measurements or any storage of data will still have
access to it. If it's found later that another TPM functionality is
exacerbating this problem a module parameter it can be turned off entirely
and a module parameter can be introduced to allow users who rely upon
fTPM functionality to turn it on even though this problem is present.
Link: https://www.amd.com/en/support/kb/faq/pa-410
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216989
Link: https://lore.kernel.org/all/20230209153120.261904-1-Jason@zx2c4.com/
Fixes: b006c439d58d ("hwrng: core - start hwrng kthread also for untrusted sources")
Cc: stable@vger.kernel.org
Cc: Jarkko Sakkinen <jarkko@kernel.org>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Cc: James Bottomley <James.Bottomley@hansenpartnership.com>
Tested-by: reach622@mailcuk.com
Tested-by: Bell <1138267643@qq.com>
Co-developed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
tpm_read_log_acpi() should return -ENODEV when no eventlog from the ACPI
table is found. If the firmware vendor includes an invalid log address
we are unable to map from the ACPI memory and tpm_read_log() returns -EIO
which would abort discovery of the eventlog.
Change the return value from -EIO to -ENODEV when acpi_os_map_iomem()
fails to map the event log.
The following hardware was used to test this issue:
Framework Laptop (Pre-production)
BIOS: INSYDE Corp, Revision: 3.2
TPM Device: NTC, Firmware Revision: 7.2
Dump of the faulty ACPI TPM2 table:
[000h 0000 4] Signature : "TPM2" [Trusted Platform Module hardware interface Table]
[004h 0004 4] Table Length : 0000004C
[008h 0008 1] Revision : 04
[009h 0009 1] Checksum : 2B
[00Ah 0010 6] Oem ID : "INSYDE"
[010h 0016 8] Oem Table ID : "TGL-ULT"
[018h 0024 4] Oem Revision : 00000002
[01Ch 0028 4] Asl Compiler ID : "ACPI"
[020h 0032 4] Asl Compiler Revision : 00040000
[024h 0036 2] Platform Class : 0000
[026h 0038 2] Reserved : 0000
[028h 0040 8] Control Address : 0000000000000000
[030h 0048 4] Start Method : 06 [Memory Mapped I/O]
[034h 0052 12] Method Parameters : 00 00 00 00 00 00 00 00 00 00 00 00
[040h 0064 4] Minimum Log Length : 00010000
[044h 0068 8] Log Address : 000000004053D000
Fixes: 0cf577a03f21 ("tpm: Fix handling of missing event log")
Tested-by: Erkki Eilonen <erkki@bearmetal.eu>
Signed-off-by: Morten Linderud <morten@linderud.pw>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes and removal from Greg KH:
"Here are four small staging driver fixes, and one big staging driver
deletion for 6.3-rc2.
The fixes are:
- rtl8192e driver fixes for where the driver was attempting to
execute various programs directly from the disk for unknown reasons
- rtl8723bs driver fixes for issues found by Hans in testing
The deleted driver is the removal of the r8188eu wireless driver as
now in 6.3-rc1 we have a "real" wifi driver for one that includes
support for many many more devices than this old driver did. So it's
time to remove it as it is no longer needed. The maintainers of this
driver all have acked its removal. Many thanks to them over the years
for working to clean it up and keep it working while the real driver
was being developed.
All of these have been in linux-next this week with no reported
problems"
* tag 'staging-6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8188eu: delete driver
staging: rtl8723bs: Pass correct parameters to cfg80211_get_bss()
staging: rtl8723bs: Fix key-store index handling
staging: rtl8192e: Remove call_usermodehelper starting RadioPower.sh
staging: rtl8192e: Remove function ..dm_check_ac_dc_power calling a script
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"This marks the end of a transition to let I2C have the same probe
semantics as other subsystems. Uwe took care that no drivers in the
current tree nor in -next use the deprecated .probe call. So, it is a
good time to switch to the new, standard semantics now.
There is also a regression fix:
- regression fix for the notifier handling of the I2C core
- final coversions of drivers away from deprecated .probe
- make .probe_new the standard probe and convert I2C core to use it
* tag 'i2c-for-6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: dev: Fix bus callback return values
i2c: Convert drivers to new .probe() callback
i2c: mux: Convert all drivers to new .probe() callback
i2c: Switch .probe() to not take an id parameter
media: i2c: ov2685: convert to i2c's .probe_new()
media: i2c: ov5695: convert to i2c's .probe_new()
w1: ds2482: Convert to i2c's .probe_new()
serial: sc16is7xx: Convert to i2c's .probe_new()
mtd: maps: pismo: Convert to i2c's .probe_new()
misc: ad525x_dpot-i2c: Convert to i2c's .probe_new()
|
|
Switching to BLK_MQ_F_BLOCKING wrongly removed the call to
blk_mq_end_request(). Add it back to have our IOs finished
Fixes: 91cc8fbcc8c7 ("ubi: block: set BLK_MQ_F_BLOCKING")
Analyzed-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/linux-mtd/CAHk-=wi29bbBNh3RqJKu3PxzpjDN5D5K17gEVtXrb7-6bfrnMQ@mail.gmail.com/
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Twenty fixes all in drivers except the one zone storage revalidation
fix to sd.
The megaraid_sas fixes are more on the level of a driver update
(enabling crash dump and increasing lun number) but I thought you
could let this slide on -rc1 and the next most extensive update is a
load of fixes to mpi3mr"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sd: Fix wrong zone_write_granularity value during revalidate
scsi: storvsc: Handle BlockSize change in Hyper-V VHD/VHDX file
scsi: megaraid_sas: Driver version update to 07.725.01.00-rc1
scsi: megaraid_sas: Add crash dump mode capability bit in MFI capabilities
scsi: megaraid_sas: Update max supported LD IDs to 240
scsi: mpi3mr: Bad drive in topology results kernel crash
scsi: mpi3mr: NVMe command size greater than 8K fails
scsi: mpi3mr: Return proper values for failures in firmware init path
scsi: mpi3mr: Wait for diagnostic save during controller init
scsi: mpi3mr: Driver unload crashes host when enhanced logging is enabled
scsi: mpi3mr: ioctl timeout when disabling/enabling interrupt
scsi: lpfc: Avoid usage of list iterator variable after loop
scsi: lpfc: Check kzalloc() in lpfc_sli4_cgn_params_read()
scsi: ufs: mcq: qcom: Clean the return path of ufs_qcom_mcq_config_resource()
scsi: ufs: mcq: qcom: Fix passing zero to PTR_ERR
scsi: ufs: ufs-qcom: Remove impossible check
scsi: ufs: core: Add soft dependency on governor_simpleondemand
scsi: hisi_sas: Check devm_add_action() return value
scsi: qla2xxx: Add option to disable FC2 Target support
scsi: target: iscsi: Fix an error message in iscsi_check_key()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control fix from Rafael Wysocki:
"Fix a recently introduced deadlock in the int340x thermal control
driver (Srinivas Pandruvada)"
* tag 'thermal-6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: intel: int340x: processor_thermal: Fix deadlock
|
|
Pull drm fixes from Dave Airlie:
"Weekly fixes.
msm and amdgpu are the vast majority of these, otherwise some
straggler misc from last week for nouveau and cirrus and a mailmap
update for a drm developer.
mailmap:
- add an entry
nouveau:
- fix system shutdown regression
- build warning fix
cirrus:
- NULL ptr deref fix
msm:
- fix invalid ptr free in syncobj cleanup
- sync GMU removal in teardown
- a5xx preemption fixes
- fix runpm imbalance
- DPU hw fixes
- stack corruption fix
- clear DSPP reservation
amdgpu:
- Misc display fixes
- UMC 8.10 fixes
- Driver unload fixes
- NBIO 7.3.0 fix
- Error checking fixes for soc15, nv, soc21 read register interface
- Fix video cap query for VCN 4.0.4
amdkfd:
- Fix return check in doorbell handling"
* tag 'drm-fixes-2023-03-10' of git://anongit.freedesktop.org/drm/drm: (42 commits)
drm/amdgpu/soc21: Add video cap query support for VCN_4_0_4
drm/amdgpu: fix error checking in amdgpu_read_mm_registers for nv
drm/amdgpu: fix error checking in amdgpu_read_mm_registers for soc21
drm/amdgpu: fix error checking in amdgpu_read_mm_registers for soc15
drm/amdgpu: Fix the warning info when removing amdgpu device
drm/amdgpu: fix return value check in kfd
drm/amd: Fix initialization mistake for NBIO 7.3.0
drm/amdgpu: Fix call trace warning and hang when removing amdgpu device
mailmap: add mailmap entries for Faith.
drm/msm: DEVFREQ_GOV_SIMPLE_ONDEMAND is no longer needed
drm/amd/display: Update clock table to include highest clock setting
drm/amd/pm: Enable ecc_info table support for smu v13_0_10
drm/amdgpu: Support umc node harvest config on umc v8_10
drm/connector: print max_requested_bpc in state debugfs
drm/display: Don't block HDR_OUTPUT_METADATA on unknown EOTF
drm/msm/dpu: clear DSPP reservations in rm release
drm/msm/disp/dpu: fix sc7280_pp base offset
drm/msm/dpu: fix stack smashing in dpu_hw_ctl_setup_blendstage
drm/msm/dpu: don't use DPU_CLK_CTRL_CURSORn for DMA SSPP clocks
drm/msm/dpu: fix clocks settings for msm8998 SSPP blocks
...
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-6.3-2023-03-09:
amdgpu:
- Misc display fixes
- UMC 8.10 fixes
- Driver unload fixes
- NBIO 7.3.0 fix
- Error checking fixes for soc15, nv, soc21 read register interface
- Fix video cap query for VCN 4.0.4
amdkfd:
- Fix return check in doorbell handling
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230310031314.1296929-1-alexander.deucher@amd.com
|
|
Added the video capability query support for VCN version 4_0_4
Signed-off-by: Veerabadhran Gopalakrishnan <veerabadhran.gopalakrishnan@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.x
|
|
Properly skip non-existent registers as well.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2442
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Properly skip non-existent registers as well.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2442
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Properly skip non-existent registers as well.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2442
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Actually, the drm_dev_enter in psp_cmd_submit_buf does not
protect anything. If DRM device is unplugged, it will always
check the condition in WARN_ON. So drop drm_dev_enter and
drm_dev_exit in psp_cmd_submit_buf.
When removing amdgpu, the calling order is as follows:
amdgpu_pci_remove
drm_dev_unplug
amdgpu_driver_unload_kms
amdgpu_device_fini_hw
amdgpu_device_ip_fini_early
psp_hw_fini
psp_ras_terminate
psp_ta_unloadye
psp_cmd_submit_buf
[ 4507.740388] Call Trace:
[ 4507.740389] <TASK>
[ 4507.740391] psp_ta_unload+0x44/0x70 [amdgpu]
[ 4507.740485] psp_ras_terminate+0x4d/0x70 [amdgpu]
[ 4507.740575] psp_hw_fini+0x28/0xa0 [amdgpu]
[ 4507.740662] amdgpu_device_fini_hw+0x328/0x442 [amdgpu]
[ 4507.740791] amdgpu_driver_unload_kms+0x51/0x60 [amdgpu]
[ 4507.740875] amdgpu_pci_remove+0x5a/0x140 [amdgpu]
[ 4507.740962] ? _raw_spin_unlock_irqrestore+0x27/0x43
[ 4507.740965] ? __pm_runtime_resume+0x60/0x90
[ 4507.740968] pci_device_remove+0x39/0xb0
[ 4507.740971] device_remove+0x46/0x70
[ 4507.740972] device_release_driver_internal+0xd1/0x160
[ 4507.740974] driver_detach+0x4a/0x90
[ 4507.740975] bus_remove_driver+0x6c/0xf0
[ 4507.740976] driver_unregister+0x31/0x50
[ 4507.740977] pci_unregister_driver+0x40/0x90
[ 4507.740978] amdgpu_exit+0x15/0x120 [amdgpu]
v2: fix commit message style issue
Signed-off-by: lyndonli <Lyndon.Li@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This patch fixes a return value check in kfd doorbell handling.
This function should return 0(error) only when the ida_simple_get
returns < 0(error), return > 0 is a success case.
Cc: Felix Kuehling <Felix.Kuehling@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Fixes: 16f0013157bf ("drm/amdkfd: Allocate doorbells only when needed")
Acked-by: Christian Koenig <chriatian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Shashank Sharma <shashank.sharma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The same strapping initialization issue that happened on NBIO 7.5.1
appears to be happening on NBIO 7.3.0.
Apply the same fix to 7.3.0 as well.
Note: This workaround relies upon the integrated GPU being enabled
in BIOS. If the integrated GPU is disabled in BIOS a different
workaround will be required.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Link: https://lore.kernel.org/linux-usb/Y%2Fz9GdHjPyF2rNG3@glanzmann.de/T/#u
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
On GPUs with RAS enabled, below call trace and hang are observed when
shutting down device.
v2: use DRM device unplugged flag instead of shutdown flag as the check to
prevent memory wipe in shutdown stage.
[ +0.000000] RIP: 0010:amdgpu_vram_mgr_fini+0x18d/0x1c0 [amdgpu]
[ +0.000001] PKRU: 55555554
[ +0.000001] Call Trace:
[ +0.000001] <TASK>
[ +0.000002] amdgpu_ttm_fini+0x140/0x1c0 [amdgpu]
[ +0.000183] amdgpu_bo_fini+0x27/0xa0 [amdgpu]
[ +0.000184] gmc_v11_0_sw_fini+0x2b/0x40 [amdgpu]
[ +0.000163] amdgpu_device_fini_sw+0xb6/0x510 [amdgpu]
[ +0.000152] amdgpu_driver_release_kms+0x16/0x30 [amdgpu]
[ +0.000090] drm_dev_release+0x28/0x50 [drm]
[ +0.000016] devm_drm_dev_init_release+0x38/0x60 [drm]
[ +0.000011] devm_action_release+0x15/0x20
[ +0.000003] release_nodes+0x40/0xc0
[ +0.000001] devres_release_all+0x9e/0xe0
[ +0.000001] device_unbind_cleanup+0x12/0x80
[ +0.000003] device_release_driver_internal+0xff/0x160
[ +0.000001] driver_detach+0x4a/0x90
[ +0.000001] bus_remove_driver+0x6c/0xf0
[ +0.000001] driver_unregister+0x31/0x50
[ +0.000001] pci_unregister_driver+0x40/0x90
[ +0.000003] amdgpu_exit+0x15/0x120 [amdgpu]
Signed-off-by: lyndonli <Lyndon.Li@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The i2cdev_{at,de}tach_adapter() callbacks are used for two purposes:
1. As notifier callbacks, when (un)registering I2C adapters created or
destroyed after i2c_dev_init(),
2. As bus iterator callbacks, for registering already existing
adapters from i2c_dev_init(), and for cleanup.
Unfortunately both use cases expect different return values: the former
expects NOTIFY_* return codes, while the latter expects zero or error
codes, and aborts in case of error.
Hence in case 2, as soon as i2cdev_{at,de}tach_adapter() returns
(non-zero) NOTIFY_OK, the bus iterator aborts. This causes (a) only the
first already existing adapter to be registered, leading to missing
/dev/i2c-* entries, and (b) a failure to unregister all but the first
I2C adapter during cleanup.
Fix this by introducing separate callbacks for the bus iterator,
wrapping the notifier functions, and always returning succes.
Any errors inside these callback functions are unlikely to happen, and
are fatal anyway.
Fixes: cddf70d0bce71c2a ("i2c: dev: fix notifier return values")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Now that .probe() was changed not to get the id parameter, drivers can
be converted back to that with the eventual goal to drop .probe_new().
Implement that for the i2c drivers that are part of the i2c core.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Now that .probe() was changed not to get the id parameter, drivers can
be converted back to that with the eventual goal to drop .probe_new().
Implement that for the i2c mux drivers.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new() call-back
type") introduced a new probe callback to convert i2c init routines to
not take an i2c_device_id parameter. Now that all in-tree drivers are
converted to the temporary .probe_new() callback, .probe() can be
modified to match the desired prototype.
Now that .probe() and .probe_new() have the same semantic, they can be
defined as members of an anonymous union to save some memory and
simplify the core code a bit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The probe function doesn't make use of the i2c_device_id * parameter so
it can be trivially converted.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://lore.kernel.org/lkml/20221121102838.16448-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The probe function doesn't make use of the i2c_device_id * parameter so
it can be trivially converted.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://lore.kernel.org/lkml/20221121102705.16092-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Link: https://lore.kernel.org/lkml/20221118224540.619276-596-uwe@kleine-koenig.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/lkml/20221118224540.619276-572-uwe@kleine-koenig.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Acked-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/lkml/20221118224540.619276-497-uwe@kleine-koenig.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/lkml/20221118224540.619276-483-uwe@kleine-koenig.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
https://gitlab.freedesktop.org/drm/msm into drm-fixes
msm-fixes for v6.3-rc2
- Fix for possible invalid ptr free in submit ioctl syncobj cleanup path.
- Synchronize GMU removal in driver teardown path
- a5xx preemption fixes
- Fix runpm imbalance at unbind
- DPU hw catalog fixes:
- set DPU_MDP_PERIPH_0_REMOVED for sc8280xp as this is another chipset
where the PERIPH_0 block of registers is not there
- fix the DPU features supported in QCM2290 by comparing it with the
downstream device tree
- fix the length of registers in the sc7180_ctl from 0xe4 to 0x1dc
- fix the max mixer line width for sm6115 and qcm2290 chipsets in the
DPU catalog
- fix the scaler version on sm8550, sc8280xp, sm8450, sm8250, sm8350
and sm6115. This was incorrectly populated on the SW version of the
scaler library and not the scaler HW version
- Drop dim layer support for msm8998 as its not indicated to be
supported in the downstream DTSI
- fix the DPU_CLK_CTRL bits for msm 8998 sspp blocks
- Use DPU_CLK_CTRL_DMA* prefix instead of DPU_CLK_CTRL_CURSOR*
for all chipsets for the DMA sspp blocks
- fix the ping-pong block base address for sc7280 in the DPU HW catalog
- Fix stack corruption issue in the dpu_hw_ctl_setup_blendstage() function
as it was causing a negative left shift by protecting against an invalid
index
- Clear the DSPP reservations in dpu_rm_release(). This was missed out and
as as result the DSPP was not released from the resource manager global
state.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvH+VH_Wx3mFMG51CMnoiU06CM-+-WMhM73M42Qx7Bp4A@mail.gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from netfilter and bpf.
Current release - regressions:
- core: avoid skb end_offset change in __skb_unclone_keeptruesize()
- sched:
- act_connmark: handle errno on tcf_idr_check_alloc
- flower: fix fl_change() error recovery path
- ieee802154: prevent user from crashing the host
Current release - new code bugs:
- eth: bnxt_en: fix the double free during device removal
- tools: ynl:
- fix enum-as-flags in the generic CLI
- fully inherit attrs in subsets
- re-license uniformly under GPL-2.0 or BSD-3-clause
Previous releases - regressions:
- core: use indirect calls helpers for sk_exit_memory_pressure()
- tls:
- fix return value for async crypto
- avoid hanging tasks on the tx_lock
- eth: ice: copy last block omitted in ice_get_module_eeprom()
Previous releases - always broken:
- core: avoid double iput when sock_alloc_file fails
- af_unix: fix struct pid leaks in OOB support
- tls:
- fix possible race condition
- fix device-offloaded sendpage straddling records
- bpf:
- sockmap: fix an infinite loop error
- test_run: fix &xdp_frame misplacement for LIVE_FRAMES
- fix resolving BTF_KIND_VAR after ARRAY, STRUCT, UNION, PTR
- netfilter: tproxy: fix deadlock due to missing BH disable
- phylib: get rid of unnecessary locking
- eth: bgmac: fix *initial* chip reset to support BCM5358
- eth: nfp: fix csum for ipsec offload
- eth: mtk_eth_soc: fix RX data corruption issue
Misc:
- usb: qmi_wwan: add telit 0x1080 composition"
* tag 'net-6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (64 commits)
tools: ynl: fix enum-as-flags in the generic CLI
tools: ynl: move the enum classes to shared code
net: avoid double iput when sock_alloc_file fails
af_unix: fix struct pid leaks in OOB support
eth: fealnx: bring back this old driver
net: dsa: mt7530: permit port 5 to work without port 6 on MT7621 SoC
net: microchip: sparx5: fix deletion of existing DSCP mappings
octeontx2-af: Unlock contexts in the queue context cache in case of fault detection
net/smc: fix fallback failed while sendmsg with fastopen
ynl: re-license uniformly under GPL-2.0 OR BSD-3-Clause
mailmap: update entries for Stephen Hemminger
mailmap: add entry for Maxim Mikityanskiy
nfc: change order inside nfc_se_io error path
ethernet: ice: avoid gcc-9 integer overflow warning
ice: don't ignore return codes in VSI related code
ice: Fix DSCP PFC TLV creation
net: usb: qmi_wwan: add Telit 0x1080 composition
net: usb: cdc_mbim: avoid altsetting toggling for Telit FE990
netfilter: conntrack: adopt safer max chain length
net: tls: fix device-offloaded sendpage straddling records
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Benjamin Tissoires:
- fix potential out of bound write of zeroes in HID core with a
specially crafted uhid device (Lee Jones)
- fix potential use-after-free in work function in intel-ish-hid (Reka
Norman)
- selftests config fixes (Benjamin Tissoires)
- few device small fixes and support
* tag 'for-linus-2023030901' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: intel-ish-hid: ipc: Fix potential use-after-free in work function
HID: logitech-hidpp: Add support for Logitech MX Master 3S mouse
HID: cp2112: Fix driver not registering GPIO IRQ chip as threaded
selftest: hid: fix hid_bpf not set in config
HID: uhid: Over-ride the default maximum data buffer value with our own
HID: core: Provide new max_buffer_size attribute to over-ride the default
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-03-07 (ice)
This series contains updates to ice driver only.
Dave removes masking from pfcena field as it was incorrectly preventing
valid traffic classes from being enabled.
Michal resolves various smatch issues such as not propagating error
codes and returning 0 explicitly.
Arnd Bergmann resolves gcc-9 warning for integer overflow.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ethernet: ice: avoid gcc-9 integer overflow warning
ice: don't ignore return codes in VSI related code
ice: Fix DSCP PFC TLV creation
====================
Link: https://lore.kernel.org/r/20230307220714.3997294-1-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Now that the same hardware that the r8188eu driver supported is
supported by the real wireless driver rtl8xxxu, the r8188eu driver can
be deleted.
Also the rtl8xxxu driver supports way more devices, and is a fraction of
the overall size, making this a much better overall solution.
Thanks to the r8188eu developers and maintainers and reviewers over the
years, your work allowed Linux users to use their hardware before the
real driver was implemented properly.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Cc: Phillip Potter <phil@philpotter.co.uk>
Cc: Pavel Skripkin <paskripkin@gmail.com>
Acked-by: Larry Finger <LarryFinger@lwfinger.net>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Martin Kaiser <martin@kaiser.cx>
Tested-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> # Edimax N150
Acked-by: Michael Straube <straube.linux@gmail.com>
Link: https://lore.kernel.org/r/20230308131934.380395-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit d5e2d038dbece821f1af57acbeded3aa9a1832c1.
We have a report of this chip being used on a
SURECOM EP-320X-S 100/10M Ethernet PCI Adapter
which could still have been purchased in some parts
of the world 3 years ago.
Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217151
Fixes: d5e2d038dbec ("eth: fealnx: delete the driver for Myson MTD-800")
Link: https://lore.kernel.org/r/20230307171930.4008454-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The MT7530 switch from the MT7621 SoC has 2 ports which can be set up as
internal: port 5 and 6. Arınç reports that the GMAC1 attached to port 5
receives corrupted frames, unless port 6 (attached to GMAC0) has been
brought up by the driver. This is true regardless of whether port 5 is
used as a user port or as a CPU port (carrying DSA tags).
Offline debugging (blind for me) which began in the linked thread showed
experimentally that the configuration done by the driver for port 6
contains a step which is needed by port 5 as well - the write to
CORE_GSWPLL_GRP2 (note that I've no idea as to what it does, apart from
the comment "Set core clock into 500Mhz"). Prints put by Arınç show that
the reset value of CORE_GSWPLL_GRP2 is RG_GSWPLL_POSDIV_500M(1) |
RG_GSWPLL_FBKDIV_500M(40) (0x128), both on the MCM MT7530 from the
MT7621 SoC, as well as on the standalone MT7530 from MT7623NI Bananapi
BPI-R2. Apparently, port 5 on the standalone MT7530 can work under both
values of the register, while on the MT7621 SoC it cannot.
The call path that triggers the register write is:
mt753x_phylink_mac_config() for port 6
-> mt753x_pad_setup()
-> mt7530_pad_clk_setup()
so this fully explains the behavior noticed by Arınç, that bringing port
6 up is necessary.
The simplest fix for the problem is to extract the register writes which
are needed for both port 5 and 6 into a common mt7530_pll_setup()
function, which is called at mt7530_setup() time, immediately after
switch reset. We can argue that this mirrors the code layout introduced
in mt7531_setup() by commit 42bc4fafe359 ("net: mt7531: only do PLL once
after the reset"), in that the PLL setup has the exact same positioning,
and further work to consolidate the separate setup() functions is not
hindered.
Testing confirms that:
- the slight reordering of writes to MT7530_P6ECR and to
CORE_GSWPLL_GRP1 / CORE_GSWPLL_GRP2 introduced by this change does not
appear to cause problems for the operation of port 6 on MT7621 and on
MT7623 (where port 5 also always worked)
- packets sent through port 5 are not corrupted anymore, regardless of
whether port 6 is enabled by phylink or not (or even present in the
device tree)
My algorithm for determining the Fixes: tag is as follows. Testing shows
that some logic from mt7530_pad_clk_setup() is needed even for port 5.
Prior to commit ca366d6c889b ("net: dsa: mt7530: Convert to PHYLINK
API"), a call did exist for all phy_is_pseudo_fixed_link() ports - so
port 5 included. That commit replaced it with a temporary "Port 5 is not
supported!" comment, and the following commit 38f790a80560 ("net: dsa:
mt7530: Add support for port 5") replaced that comment with a
configuration procedure in mt7530_setup_port5() which was insufficient
for port 5 to work. I'm laying the blame on the patch that claimed
support for port 5, although one would have also needed the change from
commit c3b8e07909db ("net: dsa: mt7530: setup core clock even in TRGMII
mode") for the write to be performed completely independently from port
6's configuration.
Thanks go to Arınç for describing the problem, for debugging and for
testing.
Reported-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/netdev/f297c2c4-6e7c-57ac-2394-f6025d309b9d@arinc9.com/
Fixes: 38f790a80560 ("net: dsa: mt7530: Add support for port 5")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230307155411.868573-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
"A small set of assorted bug and build/warning fixes"
* tag 'platform-drivers-x86-v6.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform: mellanox: mlx-platform: Initialize shift variable to 0
platform/x86: int3472: Add GPIOs to Surface Go 3 Board data
platform/x86: ISST: Fix kernel documentation warnings
platform: x86: MLX_PLATFORM: select REGMAP instead of depending on it
platform: mellanox: select REGMAP instead of depending on it
platform/x86/intel/tpmi: Fix double free reported by Smatch
platform/x86: ISST: Increase range of valid mail box commands
platform/x86: dell-ddv: Fix temperature scaling
platform/x86: dell-ddv: Fix cache invalidation on resume
platform/x86/amd: pmc: remove CONFIG_SUSPEND checks
|
