| Age | Commit message (Collapse) | Author |
|---|
|
A problem was encountered with the Bel-Fuse 1GBT-SFP05 SFP module (which
is a 1 Gbps copper module operating in SGMII mode with an internal
BCM54616S PHY device) using the Xilinx AXI Ethernet MAC core, where the
module would work properly on the initial insertion or boot of the
device, but after the device was rebooted, the link would either only
come up at 100 Mbps speeds or go up and down erratically.
I found no meaningful changes in the PHY configuration registers between
the working and non-working boots, but the status registers seemed to
have a lot of error indications set on the SERDES side of the device on
the non-working boot. I suspect the problem is that whatever happens on
the SGMII link when the device is rebooted and the FPGA logic gets
reloaded ends up putting the module's onboard PHY into a bad state.
Since commit 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
the genphy_soft_reset call is not made automatically by the PHY core
unless the callback is explicitly specified in the driver structure. For
most of these Broadcom devices, there is probably a hardware reset that
gets asserted to reset the PHY during boot, however for SFP modules
(where the BCM54616S is commonly found) no such reset line exists, so if
the board keeps the SFP cage powered up across a reboot, it will end up
with no reset occurring during reboots.
Hook up the genphy_soft_reset callback for BCM54616S to ensure that a
PHY reset is performed before the device is initialized. This appears to
fix the issue with erratic operation after a reboot with this SFP
module.
Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter, bpf.
Quite a handful of old regression fixes but most of those are
pre-5.16.
Current release - regressions:
- fix memory leaks in the skb free deferral scheme if upper layer
protocols are used, i.e. in-kernel TCP readers like TLS
Current release - new code bugs:
- nf_tables: fix NULL check typo in _clone() functions
- change the default to y for Vertexcom vendor Kconfig
- a couple of fixes to incorrect uses of ref tracking
- two fixes for constifying netdev->dev_addr
Previous releases - regressions:
- bpf:
- various verifier fixes mainly around register offset handling
when passed to helper functions
- fix mount source displayed for bpffs (none -> bpffs)
- bonding:
- fix extraction of ports for connection hash calculation
- fix bond_xmit_broadcast return value when some devices are down
- phy: marvell: add Marvell specific PHY loopback
- sch_api: don't skip qdisc attach on ingress, prevent ref leak
- htb: restore minimal packet size handling in rate control
- sfp: fix high power modules without diagnostic monitoring
- mscc: ocelot:
- don't let phylink re-enable TX PAUSE on the NPI port
- don't dereference NULL pointers with shared tc filters
- smsc95xx: correct reset handling for LAN9514
- cpsw: avoid alignment faults by taking NET_IP_ALIGN into account
- phy: micrel: use kszphy_suspend/_resume for irq aware devices,
avoid races with the interrupt
Previous releases - always broken:
- xdp: check prog type before updating BPF link
- smc: resolve various races around abnormal connection termination
- sit: allow encapsulated IPv6 traffic to be delivered locally
- axienet: fix init/reset handling, add missing barriers, read the
right status words, stop queues correctly
- add missing dev_put() in sock_timestamping_bind_phc()
Misc:
- ipv4: prevent accidentally passing RTO_ONLINK to
ip_route_output_key_hash() by sanitizing flags
- ipv4: avoid quadratic behavior in netns dismantle
- stmmac: dwmac-oxnas: add support for OX810SE
- fsl: xgmac_mdio: add workaround for erratum A-009885"
* tag 'net-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (92 commits)
ipv4: add net_hash_mix() dispersion to fib_info_laddrhash keys
ipv4: avoid quadratic behavior in netns dismantle
net/fsl: xgmac_mdio: Fix incorrect iounmap when removing module
powerpc/fsl/dts: Enable WA for erratum A-009885 on fman3l MDIO buses
dt-bindings: net: Document fsl,erratum-a009885
net/fsl: xgmac_mdio: Add workaround for erratum A-009885
net: mscc: ocelot: fix using match before it is set
net: phy: micrel: use kszphy_suspend()/kszphy_resume for irq aware devices
net: cpsw: avoid alignment faults by taking NET_IP_ALIGN into account
nfc: llcp: fix NULL error pointer dereference on sendmsg() after failed bind()
net: axienet: increase default TX ring size to 128
net: axienet: fix for TX busy handling
net: axienet: fix number of TX ring slots for available check
net: axienet: Fix TX ring slot available check
net: axienet: limit minimum TX ring size
net: axienet: add missing memory barriers
net: axienet: reset core on initialization prior to MDIO access
net: axienet: Wait for PhyRstCmplt after core reset
net: axienet: increase reset timeout
bpf, selftests: Add ringbuf memory type confusion test
...
|
|
Merge more updates from Andrew Morton:
"55 patches.
Subsystems affected by this patch series: percpu, procfs, sysctl,
misc, core-kernel, get_maintainer, lib, checkpatch, binfmt, nilfs2,
hfs, fat, adfs, panic, delayacct, kconfig, kcov, and ubsan"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (55 commits)
lib: remove redundant assignment to variable ret
ubsan: remove CONFIG_UBSAN_OBJECT_SIZE
kcov: fix generic Kconfig dependencies if ARCH_WANTS_NO_INSTR
lib/Kconfig.debug: make TEST_KMOD depend on PAGE_SIZE_LESS_THAN_256KB
btrfs: use generic Kconfig option for 256kB page size limit
arch/Kconfig: split PAGE_SIZE_LESS_THAN_256KB from PAGE_SIZE_LESS_THAN_64KB
configs: introduce debug.config for CI-like setup
delayacct: track delays from memory compact
Documentation/accounting/delay-accounting.rst: add thrashing page cache and direct compact
delayacct: cleanup flags in struct task_delay_info and functions use it
delayacct: fix incomplete disable operation when switch enable to disable
delayacct: support swapin delay accounting for swapping without blkio
panic: remove oops_id
panic: use error_report_end tracepoint on warnings
fs/adfs: remove unneeded variable make code cleaner
FAT: use io_schedule_timeout() instead of congestion_wait()
hfsplus: use struct_group_attr() for memcpy() region
nilfs2: remove redundant pointer sbufs
fs/binfmt_elf: use PT_LOAD p_align values for static PIE
const_structs.checkpatch: add frequently used ops structs
...
|
|
Patch series "test_hash.c: refactor into KUnit", v3.
We refactored the lib/test_hash.c file into KUnit as part of the student
group LKCAMP [1] introductory hackathon for kernel development.
This test was pointed to our group by Daniel Latypov [2], so its full
conversion into a pure KUnit test was our goal in this patch series, but
we ran into many problems relating to it not being split as unit tests,
which complicated matters a bit, as the reasoning behind the original
tests is quite cryptic for those unfamiliar with hash implementations.
Some interesting developments we'd like to highlight are:
- In patch 1/5 we noticed that there was an unused define directive
that could be removed.
- In patch 4/5 we noticed how stringhash and hash tests are all under
the lib/test_hash.c file, which might cause some confusion, and we
also broke those kernel config entries up.
Overall KUnit developments have been made in the other patches in this
series:
In patches 2/5, 3/5 and 5/5 we refactored the lib/test_hash.c file so as
to make it more compatible with the KUnit style, whilst preserving the
original idea of the maintainer who designed it (i.e. George Spelvin),
which might be undesirable for unit tests, but we assume it is enough
for a first patch.
This patch (of 5):
Currently, there exist hash_32() and __hash_32() functions, which were
introduced in a patch [1] targeting architecture specific optimizations.
These functions can be overridden on a per-architecture basis to achieve
such optimizations. They must set their corresponding define directive
(HAVE_ARCH_HASH_32 and HAVE_ARCH__HASH_32, respectively) so that header
files can deal with these overrides properly.
As the supported 32-bit architectures that have their own hash function
implementation (i.e. m68k, Microblaze, H8/300, pa-risc) have only been
making use of the (more general) __hash_32() function (which only lacks
a right shift operation when compared to the hash_32() function), remove
the define directive corresponding to the arch-specific hash_32()
implementation.
[1] https://lore.kernel.org/lkml/20160525073311.5600.qmail@ns.sciencehorizons.net/
[akpm@linux-foundation.org: hash_32_generic() becomes hash_32()]
Link: https://lkml.kernel.org/r/20211208183711.390454-1-isabbasso@riseup.net
Link: https://lkml.kernel.org/r/20211208183711.390454-2-isabbasso@riseup.net
Reviewed-by: David Gow <davidgow@google.com>
Tested-by: David Gow <davidgow@google.com>
Co-developed-by: Augusto Durães Camargo <augusto.duraes33@gmail.com>
Signed-off-by: Augusto Durães Camargo <augusto.duraes33@gmail.com>
Co-developed-by: Enzo Ferreira <ferreiraenzoa@gmail.com>
Signed-off-by: Enzo Ferreira <ferreiraenzoa@gmail.com>
Signed-off-by: Isabella Basso <isabbasso@riseup.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Brendan Higgins <brendanhiggins@google.com>
Cc: Daniel Latypov <dlatypov@google.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Cc: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Cc: kernel test robot <lkp@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We'd better use the helper get_task_comm() rather than the open-coded
strlcpy() to get task comm. As the comment above the hard-coded 16, we
can replace it with TASK_COMM_LEN.
Link: https://lkml.kernel.org/r/20211120112738.45980-4-laoar.shao@gmail.com
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Acked-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Arnaldo Carvalho de Melo <arnaldo.melo@gmail.com>
Cc: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Cc: Andrii Nakryiko <andrii.nakryiko@gmail.com>
Cc: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: David Hildenbrand <david@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Kees Cook <keescook@chromium.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When kernel.h is used in the headers it adds a lot into dependency hell,
especially when there are circular dependencies are involved.
Replace kernel.h inclusion with the list of what is really being used.
The rest of the changes are induced by the above and may not be split.
Link: https://lkml.kernel.org/r/20211209123823.20425-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> [brcmfmac]
Acked-by: Kalle Valo <kvalo@kernel.org>
Cc: Arend van Spriel <aspriel@gmail.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-hsien Lin <chi-hsien.lin@infineon.com>
Cc: Wright Feng <wright.feng@infineon.com>
Cc: Chung-hsien Hsu <chung-hsien.hsu@infineon.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With NEED_PER_CPU_PAGE_FIRST_CHUNK enabled, we need a function to
populate pte, this patch adds a generic pcpu populate pte function,
pcpu_populate_pte(), which is marked __weak and used on most
architectures, but it is overridden on x86, which has its own
implementation.
Link: https://lkml.kernel.org/r/20211216112359.103822-5-wangkefeng.wang@huawei.com
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With the previous patch, we could add a generic pcpu first chunk
allocate and free function to cleanup the duplicated definations on each
architecture.
Link: https://lkml.kernel.org/r/20211216112359.103822-4-wangkefeng.wang@huawei.com
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add pcpu_fc_cpu_to_node_fn_t and pass it into pcpu_fc_alloc_fn_t, pcpu
first chunk allocation will call it to alloc memblock on the
corresponding node by it, this is prepare for the next patch.
Link: https://lkml.kernel.org/r/20211216112359.103822-3-wangkefeng.wang@huawei.com
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As reported by sparse: In the remove path, the driver would attempt to
unmap its own priv pointer - instead of the io memory that it mapped
in probe.
Fixes: 9f35a7342cff ("net/fsl: introduce Freescale 10G MDIO driver")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Once an MDIO read transaction is initiated, we must read back the data
register within 16 MDC cycles after the transaction completes. Outside
of this window, reads may return corrupt data.
Therefore, disable local interrupts in the critical section, to
maximize the probability that we can satisfy this requirement.
Fixes: d55ad2967d89 ("powerpc/mpc85xx: Create dts components for the FSL QorIQ DPAA FMan")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Clang static analysis reports this issue
ocelot_flower.c:563:8: warning: 1st function call argument
is an uninitialized value
!is_zero_ether_addr(match.mask->dst)) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The variable match is used before it is set. So move the
block.
Fixes: 75944fda1dfe ("net: mscc: ocelot: offload ingress skbedit and vlan actions to VCAP IS1")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On a setup with KSZ9131 and MACB drivers it happens on suspend path, from
time to time, that the PHY interrupt arrives after PHY and MACB were
suspended (PHY via genphy_suspend(), MACB via macb_suspend()). In this
case the phy_read() at the beginning of kszphy_handle_interrupt() will
fail (as MACB driver is suspended at this time) leading to phy_error()
being called and a stack trace being displayed on console. To solve this
.suspend/.resume functions for all KSZ devices implementing
.handle_interrupt were replaced with kszphy_suspend()/kszphy_resume()
which disable/enable interrupt before/after calling
genphy_suspend()/genphy_resume().
The fix has been adapted for all KSZ devices which implements
.handle_interrupt but it has been tested only on KSZ9131.
Fixes: 59ca4e58b917 ("net: phy: micrel: implement generic .handle_interrupt() callback")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both versions of the CPSW driver declare a CPSW_HEADROOM_NA macro that
takes NET_IP_ALIGN into account, but fail to use it appropriately when
storing incoming packets in memory. This results in the IPv4 source and
destination addresses to appear misaligned in memory, which causes
aligment faults that need to be fixed up in software.
So let's switch from CPSW_HEADROOM to CPSW_HEADROOM_NA where needed.
This gets rid of any alignment faults on the RX path on a Beaglebone
White.
Fixes: 9ed4050c0d75 ("net: ethernet: ti: cpsw: add XDP support")
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With previous changes to make the driver handle the TX ring size more
correctly, the default TX ring size of 64 appears to significantly
bottleneck TX performance to around 600 Mbps on a 1 Gbps link on ZynqMP.
Increasing this to 128 seems to bring performance up to near line rate and
shouldn't cause excess bufferbloat (this driver doesn't yet support modern
byte-based queue management).
Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Network driver documentation indicates we should be avoiding returning
NETDEV_TX_BUSY from ndo_start_xmit in normal cases, since it requires
the packets to be requeued. Instead the queue should be stopped after
a packet is added to the TX ring when there may not be enough room for an
additional one. Also, when TX ring entries are completed, we should only
wake the queue if we know there is room for another full maximally
fragmented packet.
Print a warning if there is insufficient space at the start of start_xmit,
since this should no longer happen.
Combined with increasing the default TX ring size (in a subsequent
patch), this appears to recover the TX performance lost by previous changes
to actually manage the TX ring state properly.
Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The check for the number of available TX ring slots was off by 1 since a
slot is required for the skb header as well as each fragment. This could
result in overwriting a TX ring slot that was still in use.
Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The check for whether a TX ring slot was available was incorrect,
since a slot which had been loaded with transmit data but the device had
not started transmitting would be treated as available, potentially
causing non-transmitted slots to be overwritten. The control field in
the descriptor should be checked, rather than the status field (which may
only be updated when the device completes the entry).
Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver will not work properly if the TX ring size is set to below
MAX_SKB_FRAGS + 1 since it needs to hold at least one full maximally
fragmented packet in the TX ring. Limit setting the ring size to below
this value.
Fixes: 8b09ca823ffb4 ("net: axienet: Make RX/TX ring sizes configurable")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver was missing some required memory barriers:
Use dma_rmb to ensure we see all updates to the descriptor after we see
that an entry has been completed.
Use wmb and rmb to avoid stale descriptor status between the TX path and
TX complete IRQ path.
Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some cases where the Xilinx Ethernet core was used in 1000Base-X or
SGMII modes, which use the internal PCS/PMA PHY, and the MGT
transceiver clock source for the PCS was not running at the time the
FPGA logic was loaded, the core would come up in a state where the
PCS could not be found on the MDIO bus. To fix this, the Ethernet core
(including the PCS) should be reset after enabling the clocks, prior to
attempting to access the PCS using of_mdio_find_device.
Fixes: 1a02556086fc (net: axienet: Properly handle PCS/PMA PHY for 1000BaseX mode)
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When resetting the device, wait for the PhyRstCmplt bit to be set
in the interrupt status register before continuing initialization, to
ensure that the core is actually ready. When using an external PHY, this
also ensures we do not start trying to access the PHY while it is still
in reset. The PHY reset is initiated by the core reset which is
triggered just above, but remains asserted for 5ms after the core is
reset according to the documentation.
The MgtRdy bit could also be waited for, but unfortunately when using
7-series devices, the bit does not appear to work as documented (it
seems to behave as some sort of link state indication and not just an
indication the transceiver is ready) so it can't really be relied on for
this purpose.
Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The previous timeout of 1ms was too short to handle some cases where the
core is reset just after the input clocks were started, which will
be introduced in an upcoming patch. Increase the timeout to 50ms. Also
simplify the reset timeout checking to use read_poll_timeout.
Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Add new kconfig target 'make mod2noconfig', which will be useful to
speed up the build and test iteration.
- Raise the minimum supported version of LLVM to 11.0.0
- Refactor certs/Makefile
- Change the format of include/config/auto.conf to stop double-quoting
string type CONFIG options.
- Fix ARCH=sh builds in dash
- Separate compression macros for general purposes (cmd_bzip2 etc.) and
the ones for decompressors (cmd_bzip2_with_size etc.)
- Misc Makefile cleanups
* tag 'kbuild-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (34 commits)
kbuild: add cmd_file_size
arch: decompressor: remove useless vmlinux.bin.all-y
kbuild: rename cmd_{bzip2,lzma,lzo,lz4,xzkern,zstd22}
kbuild: drop $(size_append) from cmd_zstd
sh: rename suffix-y to suffix_y
doc: kbuild: fix default in `imply` table
microblaze: use built-in function to get CPU_{MAJOR,MINOR,REV}
certs: move scripts/extract-cert to certs/
kbuild: do not quote string values in include/config/auto.conf
kbuild: do not include include/config/auto.conf from shell scripts
certs: simplify $(srctree)/ handling and remove config_filename macro
kbuild: stop using config_filename in scripts/Makefile.modsign
certs: remove misleading comments about GCC PR
certs: refactor file cleaning
certs: remove unneeded -I$(srctree) option for system_certificates.o
certs: unify duplicated cmd_extract_certs and improve the log
certs: use $< and $@ to simplify the key generation rule
kbuild: remove headers_check stub
kbuild: move headers_check.pl to usr/include/
certs: use if_changed to re-generate the key when the key type is changed
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull random number generator fixes from Jason Donenfeld:
- Some Kconfig changes resulted in BIG_KEYS being unselectable, which
Justin sent a patch to fix.
- Geert pointed out that moving to BLAKE2s bloated vmlinux on little
machines, like m68k, so we now compensate for this.
- Numerous style and house cleaning fixes, meant to have a cleaner base
for future changes.
* 'random-5.17-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
random: simplify arithmetic function flow in account()
random: selectively clang-format where it makes sense
random: access input_pool_data directly rather than through pointer
random: cleanup fractional entropy shift constants
random: prepend remaining pool constants with POOL_
random: de-duplicate INPUT_POOL constants
random: remove unused OUTPUT_POOL constants
random: rather than entropy_store abstraction, use global
random: remove unused extract_entropy() reserved argument
random: remove incomplete last_data logic
random: cleanup integer types
random: cleanup poolinfo abstraction
random: fix typo in comments
lib/crypto: sha1: re-roll loops to reduce code size
lib/crypto: blake2s: move hmac construction into wireguard
lib/crypto: add prompts back to crypto libraries
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux
Pull hwspinlock updates from Bjorn Andersson:
"This contains a change to the stm32 hwspinlock driver to ensure that
the hardware is operational even without CONFIG_PM"
* tag 'hwlock-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux:
hwspinlock: stm32: enable clock at probe
|
|
Now that have_bytes is never modified, we can simplify this function.
First, we move the check for negative entropy_count to be first. That
ensures that subsequent reads of this will be non-negative. Then,
have_bytes and ibytes can be folded into their one use site in the
min_t() function.
Suggested-by: Dominik Brodowski <linux@dominikbrodowski.net>
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
This is an old driver that has seen a lot of different eras of kernel
coding style. In an effort to make it easier to code for, unify the
coding style around the current norm, by accepting some of -- but
certainly not all of -- the suggestions from clang-format. This should
remove ambiguity in coding style, especially with regards to spacing,
when code is being changed or amended. Consequently it also makes code
review easier on the eyes, following one uniform style rather than
several.
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
This gets rid of another abstraction we no longer need. It would be nice
if we could instead make pool an array rather than a pointer, but the
latent entropy plugin won't be able to do its magic in that case. So
instead we put all accesses to the input pool's actual data through the
input_pool_data array directly.
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
The entropy estimator is calculated in terms of 1/8 bits, which means
there are various constants where things are shifted by 3. Move these
into our pool info enum with the other relevant constants. While we're
at it, move an English assertion about sizes into a proper BUILD_BUG_ON
so that the compiler can ensure this invariant.
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
The other pool constants are prepended with POOL_, but not these last
ones. Rename them. This will then let us move them into the enum in the
following commit.
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
We already had the POOL_* constants, so deduplicate the older INPUT_POOL
ones. As well, fold EXTRACT_SIZE into the poolinfo enum, since it's
related.
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
We no longer have an output pool. Rather, we have just a wakeup bits
threshold for /dev/random reads, presumably so that processes don't
hang. This value, random_write_wakeup_bits, is configurable anyway. So
all the no longer usefully named OUTPUT_POOL constants were doing was
setting a reasonable default for random_write_wakeup_bits. This commit
gets rid of the constants and just puts it all in the default value of
random_write_wakeup_bits.
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Originally, the RNG used several pools, so having things abstracted out
over a generic entropy_store object made sense. These days, there's only
one input pool, and then an uneven mix of usage via the abstraction and
usage via &input_pool. Rather than this uneasy mixture, just get rid of
the abstraction entirely and have things always use the global. This
simplifies the code and makes reading it a bit easier.
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
This argument is always set to zero, as a result of us not caring about
keeping a certain amount reserved in the pool these days. So just remove
it and cleanup the function signatures.
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
There were a few things added under the "if (fips_enabled)" banner,
which never really got completed, and the FIPS people anyway are
choosing a different direction. Rather than keep around this halfbaked
code, get rid of it so that we can focus on a single design of the RNG
rather than two designs.
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Rather than using the userspace type, __uXX, switch to using uXX. And
rather than using variously chosen `char *` or `unsigned char *`, use
`u8 *` uniformly for things that aren't strings, in the case where we
are doing byte-by-byte traversal.
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Now that we're only using one polynomial, we can cleanup its
representation into constants, instead of passing around pointers
dynamically to select different polynomials. This improves the codegen
and makes the code a bit more straightforward.
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
s/or/for
Signed-off-by: Schspa Shi <schspa@gmail.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Basically nobody should use blake2s in an HMAC construction; it already
has a keyed variant. But unfortunately for historical reasons, Noise,
used by WireGuard, uses HKDF quite strictly, which means we have to use
this. Because this really shouldn't be used by others, this commit moves
it into wireguard's noise.c locally, so that kernels that aren't using
WireGuard don't get this superfluous code baked in. On m68k systems,
this shaves off ~314 bytes.
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"A bunch of new support and few updates to drivers:
New support:
- DMA_MEMCPY_SG support is bought back as we have a user in Xilinx
driver
- Support for TI J721S2 SoC in k3-udma driver
- Support for Ingenic MDMA and BDMA in the JZ4760
- Support for Renesas r8a779f0 dmac
Updates:
- We are finally getting rid of slave_id, so this brings in the
changes across tree for that
- updates for idxd driver
- at_xdmac driver cleanup"
* tag 'dmaengine-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (60 commits)
dt-bindings: dma-controller: Split interrupt fields in example
dmaengine: pch_dma: Remove usage of the deprecated "pci-dma-compat.h" API
dmaengine: at_xdmac: Fix race over irq_status
dmaengine: at_xdmac: Remove a level of indentation in at_xdmac_tasklet()
dmaengine: at_xdmac: Fix at_xdmac_lld struct definition
dmaengine: at_xdmac: Fix lld view setting
dmaengine: at_xdmac: Remove a level of indentation in at_xdmac_advance_work()
dmaengine: at_xdmac: Fix concurrency over xfers_list
dmaengine: at_xdmac: Move the free desc to the tail of the desc list
dmaengine: at_xdmac: Fix race for the tx desc callback
dmaengine: at_xdmac: Fix concurrency over chan's completed_cookie
dmaengine: at_xdmac: Print debug message after realeasing the lock
dmaengine: at_xdmac: Start transfer for cyclic channels in issue_pending
dmaengine: at_xdmac: Don't start transactions at tx_submit level
dmaengine: idxd: deprecate token sysfs attributes for read buffers
dmaengine: idxd: change bandwidth token to read buffers
dmaengine: idxd: fix wq settings post wq disable
dmaengine: idxd: change MSIX allocation based on per wq activation
dmaengine: idxd: fix descriptor flushing locking
dmaengine: idxd: embed irq_entry in idxd_wq struct
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ATA updates from Damien Le Moal:
"A larger than usual set of changes for this cycle. The bulk of the
changes are part of a rework of libata messages and debugging features
from Hannes. In more detail, the changes are as follows.
- Small code cleanups in the pata_ali driver (unnecessary variable
initialization and simplified return statement, from Jason and
Colin.
- Switch to using struct_group() in the sata_fsl driver, from Kees.
- Convert many sysfs attribute show functions to use sysfs_emit()
instead of snprintf(), from me.
- sata_dwc_460ex driver code cleanups, from Andy.
- Improve DMA setup and remove superfluous error message in
libahci_platform, from Andy
- A small code cleanup in libata to use min() instead of open coding
test, from Changcheng.
- Rework of libata messages from Hannes. This is especially focused
on replacing compile time defined debugging messages (DPRINTK() and
VPRINTK()) with regular dynamic debugging messages (pr_debug()) and
traceipoint events. Both libata-core and many drivers are updated
to have a consistent debugging level control for all drivers.
- Extend compile test support to as many drivers as possible in ATA
Kconfig to improve compile test coverage, from me.
- Fixes to avoid compile time warnings (W=1) and sparse warnings in
sata_fsl and ahci_xgene drivers, from me.
- Fix the interface of the read_id() port operation method to clarify
that the data buffer passed as an argument is little endian. This
avoids sparse warnings in the pata_netcell, pata_it821x,
ahci_xgene, ahci_cevaxi and ahci_brcm drivers. From me.
- Small code cleanup in the pata_octeon_cf driver, from Minghao.
- Improved IRQ configuration code in pata_of_platform, from Lad.
- Simplified implementation of __ata_scsi_queuecmd(), from Wenchao.
- Debounce delay flag renaming, from Paul.
- Add support for AMD A85 FCH (Hudson D4) AHCI adapters, from Paul"
* tag 'ata-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata: (106 commits)
ata: pata_ali: remove redundant return statement
ata: ahci: Add support for AMD A85 FCH (Hudson D4)
ata: libata: Rename link flag ATA_LFLAG_NO_DB_DELAY
ata: libata-scsi: simplify __ata_scsi_queuecmd()
ata: pata_of_platform: Use platform_get_irq_optional() to get the interrupt
ata: pata_samsung_cf: add compile test support
ata: pata_pxa: add compile test support
ata: pata_imx: add compile test support
ata: pata_ftide010: add compile test support
ata: pata_cs5535: add compile test support
ata: pata_octeon_cf: remove redundant val variable
ata: fix read_id() ata port operation interface
ata: ahci_xgene: use correct type for port mmio address
ata: sata_fsl: fix cmdhdr_tbl_entry and prde struct definitions
ata: sata_fsl: fix scsi host initialization
ata: pata_bk3710: add compile test support
ata: ahci_seattle: add compile test support
ata: ahci_xgene: add compile test support
ata: ahci_tegra: add compile test support
ata: ahci_sunxi: add compile test support
...
|
|
Pull virtio updates from Michael Tsirkin:
"virtio,vdpa,qemu_fw_cfg: features, cleanups, and fixes.
- partial support for < MAX_ORDER - 1 granularity for virtio-mem
- driver_override for vdpa
- sysfs ABI documentation for vdpa
- multiqueue config support for mlx5 vdpa
- and misc fixes, cleanups"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (42 commits)
vdpa/mlx5: Fix tracking of current number of VQs
vdpa/mlx5: Fix is_index_valid() to refer to features
vdpa: Protect vdpa reset with cf_mutex
vdpa: Avoid taking cf_mutex lock on get status
vdpa/vdpa_sim_net: Report max device capabilities
vdpa: Use BIT_ULL for bit operations
vdpa/vdpa_sim: Configure max supported virtqueues
vdpa/mlx5: Report max device capabilities
vdpa: Support reporting max device capabilities
vdpa/mlx5: Restore cur_num_vqs in case of failure in change_num_qps()
vdpa: Add support for returning device configuration information
vdpa/mlx5: Support configuring max data virtqueue
vdpa/mlx5: Fix config_attr_mask assignment
vdpa: Allow to configure max data virtqueues
vdpa: Read device configuration only if FEATURES_OK
vdpa: Sync calls set/get config/status with cf_mutex
vdpa/mlx5: Distribute RX virtqueues in RQT object
vdpa: Provide interface to read driver features
vdpa: clean up get_config_size ret value handling
virtio_ring: mark ring unused on error
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux
Pull remoteproc updates from Bjorn Andersson:
"This introduces support for controlling the Cortex R7 co-processor in
Renesas Gen3, support for R5F clusters and C71x DSPs on TI J721S2 and
compute, audio and modem subsystems on Qualcomm SM6350.
It fixes a couple of sparse errors related to memcpy_to/fromio and
corrects the kerneldoc spelling of "Return:".
The stm32 driver no longer attempts to communicate with the remote
after the firmware has crashed"
* tag 'rproc-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: (22 commits)
remoteproc: stm32: Improve crash recovery time
remoteproc: rcar_rproc: Remove trailing semicolon
remoteproc: rcar_rproc: Fix pm_runtime_get_sync error check
remoteproc: qcom: pas: Add SM6350 CDSP support
remoteproc: qcom: pas: Add SM6350 ADSP support
remoteproc: qcom: pas: Add SM6350 MPSS support
dt-bindings: remoteproc: qcom: pas: Add SM6350 adsp, cdsp & mpss
remoteproc: qcom: pas: Add missing power-domain "mxc" for CDSP
remoteproc: imx_rproc: correct firmware reload
remoteproc: qcom: pil_info: Don't memcpy_toio more than is provided
remoteproc: Add Renesas rcar driver
dt-bindings: remoteproc: Add Renesas R-Car
remoteproc: Fix remaining wrong return formatting in documentation
MAINTAINERS: Removing Ohad from remoteproc/rpmsg maintenance
remoteproc: ingenic: Request IRQ disabled
remoteproc: k3-r5: Extend support for R5F clusters on J721S2 SoCs
remoteproc: k3-dsp: Extend support for C71x DSPs on J721S2 SoCs
dt-bindings: remoteproc: k3-dsp: Update bindings for J721S2 SoCs
dt-bindings: remoteproc: k3-r5f: Update bindings for J721S2 SoCs
remoteproc: coredump: Correct argument 2 type for memcpy_fromio
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux
Pull rpmsg updates from Bjorn Andersson:
"This adds pr_fmt for the rpmsg_char driver, fixes error handling in
rpmsg_dev_probe() and corrects the spelling of "Return:" in various
places, in order to fix kerneldoc"
* tag 'rpmsg-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux:
rpmsg: core: Clean up resources on announce_create failure.
rpmsg: Fix documentation return formatting
rpmsg: char: Add pr_fmt() to prefix messages
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"This is a continuation of the rework of device power management macros
used for declaring device power management callbacks (Paul Cercueil)"
* tag 'pm-5.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
iio: pressure: bmp280: Use new PM macros
PM: runtime: Add EXPORT[_GPL]_RUNTIME_DEV_PM_OPS macros
PM: runtime: Add DEFINE_RUNTIME_DEV_PM_OPS() macro
PM: core: Add EXPORT[_GPL]_SIMPLE_DEV_PM_OPS macros
PM: core: Remove static qualifier in DEFINE_SIMPLE_DEV_PM_OPS macro
PM: core: Remove DEFINE_UNIVERSAL_DEV_PM_OPS() macro
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"The most significant item here is the Platform Firmware Runtime Update
and Telemetry (PFRUT) support designed to allow certain pieces of the
platform firmware to be updated on the fly, among other things.
Also important is the e820 handling change on x86 that should work
around PCI BAR allocation issues on some systems shipping since 2019.
The rest is just a handful of assorted fixes and cleanups on top of
the ACPI material merged previously.
Specifics:
- Add support for the the Platform Firmware Runtime Update and
Telemetry (PFRUT) interface based on ACPI to allow certain pieces
of the platform firmware to be updated without restarting the
system and to provide a mechanism for collecting platform firmware
telemetry data (Chen Yu, Dan Carpenter, Yang Yingliang).
- Ignore E820 reservations covering PCI host bridge windows on
sufficiently recent x86 systems to avoid issues with allocating PCI
BARs on systems where the E820 reservations cover the entire PCI
host bridge memory window returned by the _CRS object in the
system's ACPI tables (Hans de Goede).
- Fix and clean up acpi_scan_init() (Rafael Wysocki).
- Add more sanity checking to ACPI SPCR tables parsing (Mark
Langsdorf).
- Fix up ACPI APD (AMD Soc) driver initialization (Jiasheng Jiang).
- Drop unnecessary "static" from the ACPI PCC address space handling
driver added recently (kernel test robot)"
* tag 'acpi-5.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: PCC: pcc_ctx can be static
ACPI: scan: Rename label in acpi_scan_init()
ACPI: scan: Simplify initialization of power and sleep buttons
ACPI: scan: Change acpi_scan_init() return value type to void
ACPI: SPCR: check if table->serial_port.access_width is too wide
ACPI: APD: Check for NULL pointer after calling devm_ioremap()
x86/PCI: Ignore E820 reservations for bridge windows on newer systems
ACPI: pfr_telemetry: Fix info leak in pfrt_log_ioctl()
ACPI: pfr_update: Fix return value check in pfru_write()
ACPI: tools: Introduce utility for firmware updates/telemetry
ACPI: Introduce Platform Firmware Runtime Telemetry driver
ACPI: Introduce Platform Firmware Runtime Update device driver
efi: Introduce EFI_FIRMWARE_MANAGEMENT_CAPSULE_HEADER and corresponding structures
|
|
Merge support for the Platform Firmware Runtime Update and Telemetry
interface based on ACPI.
The interface provided here allows updating certain pieces of the
platform firmware without restarting the system and collecting
platform firmware telemetry data.
This also includes a utility for accesing the new interface from user
space.
* acpi-pfrut:
ACPI: pfr_telemetry: Fix info leak in pfrt_log_ioctl()
ACPI: pfr_update: Fix return value check in pfru_write()
ACPI: tools: Introduce utility for firmware updates/telemetry
ACPI: Introduce Platform Firmware Runtime Telemetry driver
ACPI: Introduce Platform Firmware Runtime Update device driver
efi: Introduce EFI_FIRMWARE_MANAGEMENT_CAPSULE_HEADER and corresponding structures
|
|
Merge additional ACPI-related updates for 5.17-rc1:
- Ignore E820 reservations covering PCI host bridge windows on
sufficiently recent x86 systems to avoid issues with allocating
PCI BARs on systems where the E820 reservations cover the entire
PCI host bridge memory window returned by the _CRS object in the
system's ACPI tables (Hans de Goede).
- Add more sanity checking to ACPI SPCR tables parsing (Mark
Langsdorf).
- Fix up ACPI APD (AMD Soc) driver initialization (Jiasheng Jiang).
- Drop unnecessary "static" from the ACPI PCC address space handling
driver added recently (kernel test robot).
* acpi-x86:
x86/PCI: Ignore E820 reservations for bridge windows on newer systems
* acpi-tables:
ACPI: SPCR: check if table->serial_port.access_width is too wide
* acpi-soc:
ACPI: APD: Check for NULL pointer after calling devm_ioremap()
* acpi-pcc:
ACPI: PCC: pcc_ctx can be static
|
|
Commit 7cfa9c92d0a3 ("net: sfp: avoid power switch on address-change
modules") unintetionally changed the semantics for high power modules
without the digital diagnostics monitoring. We repeatedly attempt to
read the power status from the non-existing 0xa2 address in a futile
hope this failure is temporary:
[ 8.856051] sfp sfp-eth3: module NTT 0000000000000000 rev 0000 sn 0000000000000000 dc 160408
[ 8.865843] mvpp2 f4000000.ethernet eth3: switched to inband/1000base-x link mode
[ 8.873469] sfp sfp-eth3: Failed to read EEPROM: -5
[ 8.983251] sfp sfp-eth3: Failed to read EEPROM: -5
[ 9.103250] sfp sfp-eth3: Failed to read EEPROM: -5
We previosuly assumed such modules were powered up in the correct mode,
continuing without further configuration as long as the required power
class was supported by the host.
Restore this behaviour, while preserving the intent of subsequent
patches to avoid the "Address Change Sequence not supported" warning
if we are not going to be accessing the DDM address.
Fixes: 7cfa9c92d0a3 ("net: sfp: avoid power switch on address-change modules")
Reported-by: 照山周一郎 <teruyama@springboard-inc.jp>
Tested-by: 照山周一郎 <teruyama@springboard-inc.jp>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
