| Age | Commit message (Collapse) | Author |
|---|
|
A use-after-free was found using KASAN. In brcmf_p2p_del_if() the virtual
interface is removed using call to brcmf_remove_interface(). After that
the virtual interface instance has been freed and should not be referenced.
Solve this by storing the nl80211 iftype in local variable, which is used
in a couple of places anyway.
Cc: stable@vger.kernel.org # 4.10.x, 4.9.x
Reported-by: Daniel J Blueman <daniel@quora.org>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Following commit cceb0a597320 ("rtlwifi: Add work queue for c2h cmd."),
the following BUG is reported when rtl8723be is used:
BUG: sleeping function called from invalid context at mm/slab.h:432
in_atomic(): 1, irqs_disabled(): 1, pid: 0, name: swapper/0
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W O 4.11.0-rc3-wl+ #276
Hardware name: TOSHIBA TECRA A50-A/TECRA A50-A, BIOS Version 4.50 09/29/2014
Call Trace:
<IRQ>
dump_stack+0x63/0x89
___might_sleep+0xe9/0x130
__might_sleep+0x4a/0x90
kmem_cache_alloc_trace+0x19f/0x200
? rtl_c2hcmd_enqueue+0x3e/0x110 [rtlwifi]
rtl_c2hcmd_enqueue+0x3e/0x110 [rtlwifi]
rtl8723be_c2h_packet_handler+0xac/0xc0 [rtl8723be]
rtl8723be_rx_command_packet+0x37/0x5c [rtl8723be]
_rtl_pci_rx_interrupt+0x200/0x6b0 [rtl_pci]
_rtl_pci_interrupt+0x20c/0x5d0 [rtl_pci]
__handle_irq_event_percpu+0x3f/0x1d0
handle_irq_event_percpu+0x23/0x60
handle_irq_event+0x3c/0x60
handle_fasteoi_irq+0xa2/0x170
handle_irq+0x20/0x30
do_IRQ+0x48/0xd0
common_interrupt+0x89/0x89
...
Although commit cceb0a597320 converted most c2h commands to use a work
queue, the Bluetooth coexistence routines can be in atomic mode when
they execute such a call.
Fixes: cceb0a597320 ("rtlwifi: Add work queue for c2h cmd.")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Allow working IBSS also when working in DQA mode.
This is done by setting it to treat the queues the
same as a BSS AP treats the queues.
Fixes: 7948b87308a4 ("iwlwifi: mvm: enable dynamic queue allocation mode")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This is a static analysis fix. The warning is:
drivers/net/wireless/intel/iwlwifi/mvm/fw-dbg.c:912 iwl_mvm_fw_dbg_collect()
warn: integer overflows 'sizeof(*desc) + len'
I guess this code is supposed to take a NUL character, but if we write
zero bytes then it tries to write -1 characters and crashes.
Fixes: c91b865cb14d ("iwlwifi: mvm: support description for user triggered fw dbg collection")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Access should be by rcu_dereference. Issue was found by sparse.
Fixes: 65e254821cee ("iwlwifi: mvm: use firmware station PM notification for AP_LINK_PS")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In the 'commit ebee76f7fa46 ("ath10k: allow setting coverage class")',
it inherits the design and the address offset from ath9k, but the address
is not applicable to QCA6174, which leads to a random crash while doing the
resume() operation, since the set_coverage_class.ops will be called from
ieee80211_reconfig() when resume() (if the wow is not configured).
Fix the incorrect address offset here to avoid the random crash.
Verified on QCA6174/hw3.0 with firmware WLAN.RM.4.4-00022-QCARMSWPZ-2.
kvalo: this also seems to fix a regression with firmware restart.
Fixes: ebee76f7fa46 ("ath10k: allow setting coverage class")
Cc: <stable@vger.kernel.org> # v4.10
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
We manually init wakeup info, but we don't detach it on device removal.
This means that if we (for example) rmmod + modprobe the driver, the
device framework might return -EEXIST the second time, and we'll
complain in the logs:
[ 839.311881] mwifiex_pcie 0000:01:00.0: fail to init wakeup for mwifiex
AFAICT, there's no other negative effect.
But we can fix this by disabling wakeup on remove, similar to what a few
other drivers do (e.g., the power supply framework).
This code (and bug) has existed on SDIO for a while, but it got moved
around and enabled for PCIe with commit 853402a00823 ("mwifiex: Enable
WoWLAN for both sdio and pcie").
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The mwifiex_dbg() log handler utilizes the struct device in
adapter->dev. Without it, it decides not to print anything.
As of commit 2e02b5814217 ("mwifiex: Allow mwifiex early access to device
structure"), we started assigning that pointer only after we finished
mwifiex_register() -- this effectively neuters any mwifiex_dbg() logging
done before this point.
Let's move the device assignment into mwifiex_register().
Fixes: 2e02b5814217 ("mwifiex: Allow mwifiex early access to device structure")
Cc: Rajat Jain <rajatja@google.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When PCIe FLR support was added, much of the remove/release code for
PCIe was migrated to ->down_dev(), but ->down_dev() is never called for
device removal. Let's refactor the cleanup to be done in both cases.
Also, drop the comments above mwifiex_cleanup_pcie(), because they were
clearly wrong, and it's better to have clear and obvious code than to
detail the code steps in comments anyway.
Fixes: 4c5dae59d2e9 ("mwifiex: add PCIe function level reset support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When a station is asleep, the fw will set it as "asleep".
All queues that are used only by one station will be stopped by
the fw.
In pre-DQA mode this was relevant for aggregation queues. However,
in DQA mode a queue is owned by one station only, so all queues
will be stopped.
As a result, we don't expect to get filtered frames back to
mac80211 and don't have to maintain the entire pending_frames
state logic, the same way as we do in aggregations.
The correct behavior is to align DQA behavior with the aggregation
queue behaviour pre-DQA:
- Don't count pending frames.
- Let mac80211 know we have frames in these queues so that it can
properly handle trigger frames.
When a trigger frame is received, mac80211 tells the driver to send
frames from the queues using release_buffered_frames.
The driver will tell the fw to let frames out even if the station
is asleep. This is done by iwl_mvm_sta_modify_sleep_tx_count.
Reported-and-tested-by: Jens Axboe <axboe@kernel.dk>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Newer hardware does not provide a cumulative payload length when multiple
descriptors are needed to handle the data. Once the MTU increases beyond
the size that can be handled by a single descriptor, the SKB does not get
built properly by the driver.
The driver will now calculate the size of the data buffers used by the
hardware. The first buffer of the first descriptor is for packet headers
or packet headers and data when the headers can't be split. Subsequent
descriptors in a multi-descriptor chain will not use the first buffer. The
second buffer is used by all the descriptors in the chain for payload data.
Based on whether the driver is processing the first, intermediate, or last
descriptor it can calculate the buffer usage and build the SKB properly.
Tested and verified on both old and new hardware.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Suspending the PHY would be putting it in a low power state where it
may no longer allow us to do Wake-on-LAN.
Fixes: cc013fb48898 ("net: bcmgenet: correctly suspend and resume PHY device")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes netdev->features for Extended Socket network device.
Currently Extended Socket network device's netdev->feature claims
NETIF_F_HW_CSUM, however this is completely wrong. There's no feature
of checksum offloading.
That causes invalid TCP/UDP checksum and packet rejection when IP
forwarding from Extended Socket network device to other network device.
NETIF_F_HW_CSUM should be omitted.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a rather large set of fixes. The bulk are for lpfc correcting
a lot of issues in the new NVME driver code which just went in in the
merge window.
The others are:
- fix a hang in the vmware paravirt driver caused by incorrect
handling of the new MSI vector allocation
- long standing bug in storvsc, which recent block changes turned
from being a harmless annoyance into a hang
- yet more fallout (in mpt3sas) from the changes to device blocking
The remainder are small fixes and updates"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (34 commits)
scsi: lpfc: Add shutdown method for kexec
scsi: storvsc: Workaround for virtual DVD SCSI version
scsi: lpfc: revise version number to 11.2.0.10
scsi: lpfc: code cleanups in NVME initiator discovery
scsi: lpfc: code cleanups in NVME initiator base
scsi: lpfc: correct rdp diag portnames
scsi: lpfc: remove dead sli3 nvme code
scsi: lpfc: correct double print
scsi: lpfc: Rename LPFC_MAX_EQ_DELAY to LPFC_MAX_EQ_DELAY_EQID_CNT
scsi: lpfc: Rework lpfc Kconfig for NVME options
scsi: lpfc: add transport eh_timed_out reference
scsi: lpfc: Fix eh_deadline setting for sli3 adapters.
scsi: lpfc: add NVME exchange aborts
scsi: lpfc: Fix nvme allocation bug on failed nvme_fc_register_localport
scsi: lpfc: Fix IO submission if WQ is full
scsi: lpfc: Fix NVME CMD IU byte swapped word 1 problem
scsi: lpfc: Fix RCTL value on NVME LS request and response
scsi: lpfc: Fix crash during Hardware error recovery on SLI3 adapters
scsi: lpfc: fix missing spin_unlock on sql_list_lock
scsi: lpfc: don't dereference dma_buf->iocbq before null check
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
- self-test failure of crc32c on powerpc
- regressions of ecb(aes) when used with xts/lrw in s5p-sss
- a number of bugs in the omap RNG driver
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: s5p-sss - Fix spinlock recursion on LRW(AES)
hwrng: omap - Do not access INTMASK_REG on EIP76
hwrng: omap - use devm_clk_get() instead of of_clk_get()
hwrng: omap - write registers after enabling the clock
crypto: s5p-sss - Fix completing crypto request in IRQ handler
crypto: powerpc - Fix initialisation of crc32c context
|
|
Pull networking fixes from David Miller:
1) Ensure that mtu is at least IPV6_MIN_MTU in ipv6 VTI tunnel driver,
from Steffen Klassert.
2) Fix crashes when user tries to get_next_key on an LPM bpf map, from
Alexei Starovoitov.
3) Fix detection of VLAN fitlering feature for bnx2x VF devices, from
Michal Schmidt.
4) We can get a divide by zero when TCP socket are morphed into
listening state, fix from Eric Dumazet.
5) Fix socket refcounting bugs in skb_complete_wifi_ack() and
skb_complete_tx_timestamp(). From Eric Dumazet.
6) Use after free in dccp_feat_activate_values(), also from Eric
Dumazet.
7) Like bonding team needs to use ETH_MAX_MTU as netdev->max_mtu, from
Jarod Wilson.
8) Fix use after free in vrf_xmit(), from David Ahern.
9) Don't do UDP Fragmentation Offload on IPComp ipsec packets, from
Alexey Kodanev.
10) Properly check napi_complete_done() return value in order to decide
whether to re-enable IRQs or not in amd-xgbe driver, from Thomas
Lendacky.
11) Fix double free of hwmon device in marvell phy driver, from Andrew
Lunn.
12) Don't crash on malformed netlink attributes in act_connmark, from
Etienne Noss.
13) Don't remove routes with a higher metric in ipv6 ECMP route replace,
from Sabrina Dubroca.
14) Don't write into a cloned SKB in ipv6 fragmentation handling, from
Florian Westphal.
15) Fix routing redirect races in dccp and tcp, basically the ICMP
handler can't modify the socket's cached route in it's locked by the
user at this moment. From Jon Maxwell.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (108 commits)
qed: Enable iSCSI Out-of-Order
qed: Correct out-of-bound access in OOO history
qed: Fix interrupt flags on Rx LL2
qed: Free previous connections when releasing iSCSI
qed: Fix mapping leak on LL2 rx flow
qed: Prevent creation of too-big u32-chains
qed: Align CIDs according to DORQ requirement
mlxsw: reg: Fix SPVMLR max record count
mlxsw: reg: Fix SPVM max record count
net: Resend IGMP memberships upon peer notification.
dccp: fix memory leak during tear-down of unsuccessful connection request
tun: fix premature POLLOUT notification on tun devices
dccp/tcp: fix routing redirect race
ucc/hdlc: fix two little issue
vxlan: fix ovs support
net: use net->count to check whether a netns is alive or not
bridge: drop netfilter fake rtable unconditionally
ipv6: avoid write to a possibly cloned skb
net: wimax/i2400m: fix NULL-deref at probe
isdn/gigaset: fix NULL-deref at probe
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Three libata fixes:
- fix for a circular reference bug in sysfs code which prevented
pata_legacy devices from being released after probe failure, which
in turn prevented devres from releasing the associated resources.
- drop spurious WARN in the command issue path which can be triggered
by a legitimate passthrough command.
- an ahci_qoriq specific fix"
* 'for-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: qoriq: correct the sata ecc setting error
libata: drop WARN from protocol error in ata_sff_qc_issue()
libata: transport: Remove circular dependency at free time
|
|
Missing in the initial submission, qed fails to propagate qedi's
request to enable OOO to firmware.
Fixes: fc831825f99e ("qed: Add support for hardware offloaded iSCSI")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Need to set the number of entries in database, otherwise the logic
would quickly surpass the array.
Fixes: 1d6cff4fca43 ("qed: Add iSCSI out of order packet handling")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before iterating over the the LL2 Rx ring, the ring's
spinlock is taken via spin_lock_irqsave().
The actual processing of the packet [including handling
by the protocol driver] is done without said lock,
so qed releases the spinlock and re-claims it afterwards.
Problem is that the final spin_lock_irqrestore() at the end
of the iteration uses the original flags saved from the
initial irqsave() instead of the flags from the most recent
irqsave(). So it's possible that the interrupt status would
be incorrect at the end of the processing.
Fixes: 0a7fb11c23c0 ("qed: Add Light L2 support");
CC: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes: fc831825f99e ("qed: Add support for hardware offloaded iSCSI")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When receiving an Rx LL2 packet, qed fails to unmap the previous buffer.
Fixes: 0a7fb11c23c0 ("qed: Add Light L2 support");
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current Logic would allow the creation of a chain with U32_MAX + 1
elements, when the actual maximum supported by the driver infrastructure
is U32_MAX.
Fixes: a91eb52abb50 ("qed: Revisit chain implementation")
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Doorbell HW block can be configured at a granularity
of 16 x CIDs, so we need to make sure that the actual number
of CIDs configured would be a multiplication of 16.
Today, when RoCE is enabled - given that the number is unaligned,
doorbelling the higher CIDs would fail to reach the firmware and
would eventually timeout.
Fixes: dbb799c39717 ("qed: Initialize hardware for new protocols")
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The num_rec field is 8 bit, so the maximal count number is 255.
This fixes vlans learning not being enabled for wider ranges than 255.
Fixes: a4feea74cd7a ("mlxsw: reg: Add Switch Port VLAN MAC Learning register definition")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The num_rec field is 8 bit, so the maximal count number is 255. This
fixes vlans not being enabled for wider ranges than 255.
Fixes: b2e345f9a454 ("mlxsw: reg: Add Switch Port VID and Switch Port VLAN Membership registers definitions")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
aszlig observed failing ssh tunnels (-w) during initialization since
commit cc9da6cc4f56e0 ("ipv6: addrconf: use stable address generator for
ARPHRD_NONE"). We already had reports that the mentioned commit breaks
Juniper VPN connections. I can't clearly say that the Juniper VPN client
has the same problem, but it is worth a try to hint to this patch.
Because of the early generation of link local addresses, the kernel now
can start asking for routers on the local subnet much earlier than usual.
Those router solicitation packets arrive inside the ssh channels and
should be transmitted to the tun fd before the configuration scripts
might have upped the interface and made it ready for transmission.
ssh polls on the interface and receives back a POLL_OUT. It tries to send
the earily router solicitation packet to the tun interface. Unfortunately
it hasn't been up'ed yet by config scripts, thus failing with -EIO. ssh
doesn't retry again and considers the tun interface broken forever.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=121131
Fixes: cc9da6cc4f56 ("ipv6: addrconf: use stable address generator for ARPHRD_NONE")
Cc: Bjørn Mork <bjorn@mork.no>
Reported-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Reported-by: Jonas Lippuner <jonas@lippuner.ca>
Cc: Jonas Lippuner <jonas@lippuner.ca>
Reported-by: aszlig <aszlig@redmoonstudios.org>
Cc: aszlig <aszlig@redmoonstudios.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. modify bd_status from u32 to u16 in function hdlc_rx_done,
because bd_status register is 16bits
2. write bd_length register before writing bd_status register
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull some more powerpc fixes from Michael Ellerman:
"The main item is the addition of the Power9 Machine Check handler.
This was delayed to make sure some details were correct, and is as
minimal as possible.
The rest is small fixes, two for the Power9 PMU, two dealing with
obscure toolchain problems, two for the PowerNV IOMMU code (used by
VFIO), and one to fix a crash on 32-bit machines with macio devices
due to missing dma_ops.
Thanks to:
Alexey Kardashevskiy, Cyril Bur, Larry Finger, Madhavan Srinivasan,
Nicholas Piggin"
* tag 'powerpc-4.11-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: POWER9 machine check handler
powerpc/64s: allow machine check handler to set severity and initiator
powerpc/64s: fix handling of non-synchronous machine checks
powerpc/pmac: Fix crash in dma-mapping.h with NULL dma_ops
powerpc/powernv/ioda2: Update iommu table base on ownership change
powerpc/powernv/ioda2: Gracefully fail if too many TCE levels requested
selftests/powerpc: Replace stxvx and lxvx with stxvd2x/lxvd2x
powerpc/perf: Handle sdar_mode for marked event in power9
powerpc/perf: Fix perf_get_data_addr() for power9 DD1
powerpc/boot: Fix zImage TOC alignment
|
|
The required changes in the function vxlan_dev_create() were missing
in commit 8bcdc4f3a20b.
The vxlan device is not registered anymore after this patch and the error
path causes an stack dump:
WARNING: CPU: 3 PID: 1498 at net/core/dev.c:6713 rollback_registered_many+0x9d/0x3f0
Fixes: 8bcdc4f3a20b ("vxlan: add changelink support")
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"Asus fixes for the airplane LED and a long awaited fujitsu cleanup.
asus-wmi:
- Remove quirk_no_rfkill
- Detect quirk_no_rfkill from the DSDT
fujitsu-laptop:
- remove redundant MODULE_ALIAS entries
- autodetect LCD interface on all models
- simplify acpi_bus_register_driver() error handling
- remove redundant forward declarations
- replace numeric values with constants
- rename FUNC_RFKILL to FUNC_FLAGS
- make platform-related variables match naming convention
- replace "hotkey" with "laptop" in symbol names
- clearly denote backlight-related symbols"
* tag 'platform-drivers-x86-v4.11-2' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: asus-wmi: Remove quirk_no_rfkill
platform/x86: asus-wmi: Detect quirk_no_rfkill from the DSDT
platform/x86: fujitsu-laptop: remove redundant MODULE_ALIAS entries
platform/x86: fujitsu-laptop: autodetect LCD interface on all models
platform/x86: fujitsu-laptop: simplify acpi_bus_register_driver() error handling
platform/x86: fujitsu-laptop: remove redundant forward declarations
platform/x86: fujitsu-laptop: replace numeric values with constants
platform/x86: fujitsu-laptop: rename FUNC_RFKILL to FUNC_FLAGS
platform/x86: fujitsu-laptop: make platform-related variables match naming convention
platform/x86: fujitsu-laptop: replace "hotkey" with "laptop" in symbol names
platform/x86: fujitsu-laptop: clearly denote backlight-related symbols
|
|
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
The endpoints are specifically dereferenced in the i2400m_bootrom_init
path during probe (e.g. in i2400mu_tx_bulk_out).
Fixes: f398e4240fce ("i2400m/USB: probe/disconnect, dev init/shutdown
and reset backends")
Cc: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: cf7776dc05b8 ("[PATCH] isdn4linux: Siemens Gigaset drivers -
direct USB connection")
Cc: stable <stable@vger.kernel.org> # 2.6.17
Cc: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some cases during XenBus disconnect event handling and subsequent
queue resource release there may be some TX handlers active on
other processors. Use RCU in order to synchronize with them.
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the send indirection table from the inner device (netvsc)
to the network device context.
It is possible that netvsc_device is not present (remove in progress).
This solves potential use after free issues when packet is being
created during MTU change, shutdown, or queue count changes.
Fixes: d8e18ee0fa96 ("netvsc: enhance transmit select_queue")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a network interface controlled by the aquantia ethernet driver is brought
down a warning is output in dmesg (see below).
The problem is that aq_pci_func_free_irqs() is calling free_irq() before it is
calling irq_set_affinity_hint().
WARNING: CPU: 4 PID: 10068 at kernel/irq/manage.c:1503 __free_irq+0x24d/0x2b0
<snip>
Call Trace:
dump_stack+0x63/0x87
__warn+0xd1/0xf0
warn_slowpath_null+0x1d/0x20
__free_irq+0x24d/0x2b0
free_irq+0x39/0x90
aq_pci_func_free_irqs+0x52/0xa0 [atlantic]
aq_nic_stop+0xca/0xd0 [atlantic]
aq_ndev_close+0x1d/0x40 [atlantic]
__dev_close_many+0x99/0x100
__dev_close+0x67/0xb0
<snip>
Fixes: 36a4a50f4048 ("net: ethernet: aquantia: switch to pci_alloc_irq_vectors")
Cc: Christoph Hellwig <hch@lst.de>
Cc: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David Arcari <darcari@redhat.com>
Tested-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the detection introduced in the previous patches, we don't need
these static DMI-based quirks anymore.
This reverts the following commits:
56a37a72002b "asus-wmi: Add quirk_no_rfkill_wapf4 for the Asus X456UA"
a961a285b479 "asus-wmi: Add quirk_no_rfkill_wapf4 for the Asus X456UF"
6b7ff2af5286 "asus-wmi: Add quirk_no_rfkill for the Asus Z550MA"
02db9ff7af18 "asus-wmi: Add quirk_no_rfkill for the Asus U303LB"
2d735244b798 "asus-wmi: Add quirk_no_rfkill for the Asus N552VW"
a977e59c0c67 "asus-wmi: Create quirk for airplane_mode LED"
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[dvhart: minor commit message corrections]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
- a workaround for a GIC erratum
- a missing stub function for CONFIG_IRQDOMAIN=n
- fixes for a couple of type inconsistencies
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/crossbar: Fix incorrect type of register size
irqchip/gicv3-its: Add workaround for QDF2400 ITS erratum 0065
irqdomain: Add empty irq_domain_check_msi_remap
irqchip/crossbar: Fix incorrect type of local variables
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random updates from Ted Ts'o:
"Change get_random_{int,log} to use the CRNG used by /dev/urandom and
getrandom(2). It's faster and arguably more secure than cut-down MD5
that we had been using.
Also do some code cleanup"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: move random_min_urandom_seed into CONFIG_SYSCTL ifdef block
random: convert get_random_int/long into get_random_u32/u64
random: use chacha20 for get_random_int/long
random: fix comment for unused random_min_urandom_seed
random: remove variable limit
random: remove stale urandom_init_wait
random: remove stale maybe_reseed_primary_crng
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes frpm Greg KH:
"Here are two bugfixes for tty stuff for 4.11-rc2.
One of them resolves the pretty bad bug in the n_hdlc code that
Alexander Popov found and fixed and has been reported everywhere. The
other just fixes a samsung serial driver issue when DMA fails on some
systems.
Both have been in linux-next with no reported issues"
* tag 'tty-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: samsung: Continue to work if DMA request fails
tty: n_hdlc: get rid of racy n_hdlc.tbuf
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are two small build warning fixes for some staging drivers that
Arnd has found on his valiant quest to get the kernel to build
properly with no warnings.
Both of these have been in linux-next this week and resolve the
reported issues"
* tag 'staging-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: octeon: remove unused variable
staging/vc04_services: add CONFIG_OF dependency
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here is a number of different USB fixes for 4.11-rc2.
Seems like there were a lot of unresolved issues that people have been
finding for this subsystem, and a bunch of good security auditing
happening as well from Johan Hovold. There's the usual batch of gadget
driver fixes and xhci issues resolved as well.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (35 commits)
usb: host: xhci-plat: Fix timeout on removal of hot pluggable xhci controllers
usb: host: xhci-dbg: HCIVERSION should be a binary number
usb: xhci: remove dummy extra_priv_size for size of xhci_hcd struct
usb: xhci-mtk: check hcc_params after adding primary hcd
USB: serial: digi_acceleport: fix OOB-event processing
MAINTAINERS: usb251xb: remove reference inexistent file
doc: dt-bindings: usb251xb: mark reg as required
usb: usb251xb: dt: add unit suffix to oc-delay and power-on-time
usb: usb251xb: remove max_{power,current}_{sp,bp} properties
usb-storage: Add ignore-residue quirk for Initio INIC-3619
USB: iowarrior: fix NULL-deref in write
USB: iowarrior: fix NULL-deref at probe
usb: phy: isp1301: Add OF device ID table
usb: ohci-at91: Do not drop unhandled USB suspend control requests
USB: serial: safe_serial: fix information leak in completion handler
USB: serial: io_ti: fix information leak in completion handler
USB: serial: omninet: drop open callback
USB: serial: omninet: fix reference leaks at open
USB: serial: io_ti: fix NULL-deref in interrupt callback
usb: dwc3: gadget: make to increment req->remaining in all cases
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"Two smaller pin control fixes for the v4.11 series:
- Add a get_direction() function to the qcom driver
- Fix two pin names in the uniphier driver"
* tag 'pinctrl-v4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: uniphier: change pin names of aio/xirq for LD11
pinctrl: qcom: add get_direction function
|
|
Pull ceph fixes from Ilya Dryomov:
- a fix for the recently discovered misdirected requests bug present in
jewel and later on the server side and all stable kernels
- a fixup for -rc1 CRUSH changes
- two usability enhancements: osd_request_timeout option and
supported_features bus attribute.
* tag 'ceph-for-4.11-rc2' of git://github.com/ceph/ceph-client:
libceph: osd_request_timeout option
rbd: supported_features bus attribute
libceph: don't set weight to IN when OSD is destroyed
libceph: fix crush_decode() for older maps
|
|
Change packet type handler to ETH_P_IP instead of ETH_P_ALL
since we are already expecting an IP packet.
Also, using ETH_P_ALL will cause the loopback test packet type handler
to be called on all outgoing packets, especially our own self loopback
test SKB, which will be validated on xmit as well, and we don't want that.
Tested with:
ethtool -t ethX
validated that the loopback test passes.
Fixes: 0952da791c97 ('net/mlx5e: Add support for loopback selftest')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When deleting offloaded TC flows, we must correctly identify E-switch
rules. The current check could get us wrong w.r.t to rules set on the
PF. Since it's possible to set NIC rules on the PF, switch to SRIOV
offloads mode and then attempt to delete a NIC rule.
To solve that, we add a flags field to offloaded rules, set it on
creation time and use that over the code where currently needed.
Fixes: 8b32580df1cb ('net/mlx5e: Add TC vlan action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the function setdcbx fails if the request dcbx mode
is either IEEE or CEE. We remove the IEEE/CEE mode check because
we support both IEEE and CEE interfaces.
Fixes: 3a6a931dfb8e ("net/mlx5e: Support DCBX CEE API")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a PCI error is detected the PCI state could be corrupt, don't save
it in that flow. Save the state after initialization. After restoring the
PCI state during slot reset save it again, restoring the state destroys
the previously saved state info.
Fixes: 05ac2c0b7438 ('net/mlx5: Fix race between PCI error handlers and
health work')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The autogroups list is a list of non overlapping group boundaries
sorted by their start index. If the autogroups list wasn't empty
and an empty group slot was found at the start of the list,
the new group was added to the end of the list instead of the
beginning, as the prev initializer was incorrect.
When this was repeated, it caused multiple groups to have
overlapping boundaries.
Fixed that by correctly initializing the prev pointer to the
start of the list.
Fixes: eccec8da3b4e ('net/mlx5: Keep autogroups list ordered')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
