summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2021-10-13rtw89: add Realtek 802.11ax driverPing-Ke Shih
This driver named rtw89, which is the next generation of rtw88, supports Realtek 8852AE 802.11ax 2x2 chip whose new features are OFDMA, DBCC, Spatial reuse, TWT and BSS coloring; now some of them aren't implemented though. The chip architecture is entirely different from the chips supported by rtw88 like RTL8822CE 802.11ac chip. First of all, register address ranges are totally redefined, so it's impossible to reuse register definition. To communicate with firmware, new H2C/C2H format is proposed. In order to have better utilization, TX DMA flow is changed to two stages DMA. To provide rich RX status information, additional RX PPDU packets are added. Since there are so many differences mentioned above, we decide to propose a new driver. It has many authors, they are listed in alphabetic order: Chin-Yen Lee <timlee@realtek.com> Ping-Ke Shih <pkshih@realtek.com> Po Hao Huang <phhuang@realtek.com> Tzu-En Huang <tehuang@realtek.com> Vincent Fann <vincent_fann@realtek.com> Yan-Hsuan Chuang <tony0620emma@gmail.com> Zong-Zhe Yang <kevin_yang@realtek.com> Tested-by: Aaron Ma <aaron.ma@canonical.com> Tested-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211008035627.19463-1-pkshih@realtek.com
2021-10-11b43: fix a lower bounds testDan Carpenter
The problem is that "channel" is an unsigned int, when it's less 5 the value of "channel - 5" is not a negative number as one would expect but is very high positive value instead. This means that "start" becomes a very high positive value. The result of that is that we never enter the "for (i = start; i <= end; i++) {" loop. Instead of storing the result from b43legacy_radio_aci_detect() it just uses zero. Fixes: ef1a628d83fc ("b43: Implement dynamic PHY API") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Michael Büsch <m@bues.ch> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211006073621.GE8404@kili
2021-10-11b43legacy: fix a lower bounds testDan Carpenter
The problem is that "channel" is an unsigned int, when it's less 5 the value of "channel - 5" is not a negative number as one would expect but is very high positive value instead. This means that "start" becomes a very high positive value. The result of that is that we never enter the "for (i = start; i <= end; i++) {" loop. Instead of storing the result from b43legacy_radio_aci_detect() it just uses zero. Fixes: 75388acd0cd8 ("[B43LEGACY]: add mac80211-based driver for legacy BCM43xx devices") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Michael Büsch <m@bues.ch> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211006073542.GD8404@kili
2021-10-10octeontx2-pf: Simplify the receive buffer size calculationSubbaraya Sundeep
This patch separates the logic of configuring hardware maximum transmit frame size and receive frame size. This simplifies the logic to calculate receive buffer size and using cqe descriptor of different size. Also additional size of skb_shared_info structure is allocated for each receive buffer pointer given to hardware which is not necessary. Hence change the size calculation to remove the size of skb_shared_info. Add a check for array out of bounds while adding fragments to the network stack. Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-10ethernet: Remove redundant 'flush_workqueue()' callsChristophe JAILLET
'destroy_workqueue()' already drains the queue before destroying it, so there is no need to flush it explicitly. Remove the redundant 'flush_workqueue()' calls. This was generated with coccinelle: @@ expression E; @@ - flush_workqueue(E); destroy_workqueue(E); Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> #mlx* Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-10virtio_net: skip RCU read lock by checking xdp_enabled of viLi RongQing
networking benchmark shows that __rcu_read_lock and __rcu_read_unlock takes some cpu cycles, and we can avoid calling them partially in virtio rx path by check xdp_enabled of vi, and xdp is disabled most of time Signed-off-by: Li RongQing <lirongqing@baidu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-10net: phy: at803x: better describe debug regsAnsuel Smith
Give a name to known debug regs from Documentation instead of using unknown hex values. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-10net: phy: at803x: enable prefer master for 83xx internal phyAnsuel Smith
From original QCA source code the port was set to prefer master as port type in 1000BASE-T mode. Apply the same settings also here. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-10net: phy: at803x: add DAC amplitude fix for 8327 phyAnsuel Smith
QCA8327 internal phy require DAC amplitude adjustement set to +6% with 100m speed. Also add additional define to report a change of the same reg in QCA8337. (different scope it does set 1000m voltage) Add link_change_notify function to set the proper amplitude adjustement on PHY_RUNNING state and disable on any other state. Fixes: b4df02b562f4 ("net: phy: at803x: add support for qca 8327 A variant internal phy") Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-10net: phy: at803x: fix resume for QCA8327 phyAnsuel Smith
From Documentation phy resume triggers phy reset and restart auto-negotiation. Add a dedicated function to wait reset to finish as it was notice a regression where port sometime are not reliable after a suspend/resume session. The reset wait logic is copied from phy_poll_reset. Add dedicated suspend function to use genphy_suspend only with QCA8337 phy and set only additional debug settings for QCA8327. With more test it was reported that QCA8327 doesn't proprely support this mode and using this cause the unreliability of the switch ports, especially the malfunction of the port0. Fixes: 15b9df4ece17 ("net: phy: at803x: add resume/suspend function to qca83xx phy") Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-10hv_netvsc: use netif_is_bond_master() instead of open codeJuhee Kang
Use netif_is_bond_master() function instead of open code, which is ((event_dev->priv_flags & IFF_BONDING) && (event_dev->flags & IFF_MASTER)). This patch doesn't change logic. Signed-off-by: Juhee Kang <claudiajkang@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-10bnxt: use netif_is_rxfh_configured instead of open codeJuhee Kang
The open code which is dev->priv_flags & IFF_RXFH_CONFIGURED is defined as a helper function on netdevice.h. So use netif_is_rxfh_configured() function instead of open code. This patch doesn't change logic. Signed-off-by: Juhee Kang <claudiajkang@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-10ionic: tame the filter no space messageShannon Nelson
Override the automatic AdminQ error message in order to capture the potential No Space message when we hit the max vlan limit, and add additional messaging to detail what filter failed. Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-10ionic: allow adminq requests to override default error messageShannon Nelson
The AdminQ handler has an error handler that automatically prints an error message when the request has failed. However, there are situations where the caller can expect that it might fail and has an alternative strategy, thus may not want the error message sent to the log, such as hitting -ENOSPC when adding a new vlan id. We add a new interface to the AdminQ API to allow for override of the default behavior, and an interface to the use standard error message formatting. Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-10ionic: handle vlan id overflowShannon Nelson
Add vlans to the existing rx_filter_sync mechanics currently used for managing mac filters. Older versions of our firmware had no enforced limits on the number of vlans that the LIF could request, but requesting large numbers of vlans caused issues in FW memory management, so an arbitrary limit was added in the FW. The FW now returns -ENOSPC when it hits that limit, which the driver needs to handle. Unfortunately, the FW doesn't advertise the vlan id limit, as it does with mac filters, so the driver won't know the limit until it bumps into it. We'll grab the current vlan id count and use that as the limit from there on and thus prevent getting any more -ENOSPC errors. Just as is done for the mac filters, the device puts the device into promiscuous mode when -ENOSPC is seen for vlan ids, and the driver will track the vlans that aren't synced to the FW. When vlans are removed, the driver will retry the un-synced vlans. If all outstanding vlans are synced, the promiscuous mode will be disabled. Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-10ionic: generic filter deleteShannon Nelson
Similar to the filter add, make a generic filter delete. Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-10ionic: generic filter addShannon Nelson
In preparation for adding vlan overflow management, rework the ionic_lif_addr_add() function to something a little more generic that can be used for other filter types. Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-10ionic: add generic filter searchShannon Nelson
In preparation for enhancing vlan filter management, add a filter search routine that can figure out for itself which type of filter search is needed. Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-10ionic: remove mac overflow flagsShannon Nelson
The overflow flags really aren't useful and we don't need lif struct elements to track them. Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-10ionic: move lif mac address functionsShannon Nelson
The routines that add and delete mac addresses from the firmware really should be in the file with the rest of the filter management. This simply moves the functions with no logic changes. Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-10ionic: add filterlist to debugfsShannon Nelson
Dump the filter list to debugfs - includes the device-assigned filter id and the sync'd-to-hardware status. Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-09net: use dev_addr_set()Jakub Kicinski
Use dev_addr_set() instead of writing directly to netdev->dev_addr in various misc and old drivers. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-09ethernet: 8390: remove direct netdev->dev_addr writesJakub Kicinski
8390 contains a lot of loops assigning netdev->dev_addr byte by byte. Convert what's possible directly to eth_hw_addr_set(), use local buf in other places. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-09ethernet: sun: remove direct netdev->dev_addr writesJakub Kicinski
Consify temporary variables pointing to netdev->dev_addr. A few places need local storage but pretty simple conversion over all. Note that macaddr[] is an array of ints, so we need to keep the loops. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-09ethernet: tulip: remove direct netdev->dev_addr writesJakub Kicinski
Consify the casts of netdev->dev_addr. Convert pointless to eth_hw_addr_set() where possible. Use local buffers in a number of places. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-09ethernet: tg3: remove direct netdev->dev_addr writesJakub Kicinski
tg3 does various forms of direct writes to netdev->dev_addr. Use a local buffer. Make sure local buffer is aligned since eth_platform_get_mac_address() may call ether_addr_copy(). tg3_get_device_address() returns whenever it finds a method that found a valid address. Instead of modifying all the exit points pass the buffer from the outside and commit the address in the caller. Constify the argument of the set addr helper. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-09ethernet: forcedeth: remove direct netdev->dev_addr writesJakub Kicinski
forcedeth writes to dev_addr byte by byte, make it use a local buffer instead. Commit the changes with eth_hw_addr_set() at the end. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Zhu Yanjun <zyjzyj2000@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-08mlxsw: item: Annotate item helpers with '__maybe_unused'Ido Schimmel
mlxsw is using helpers to get / set fields in messages exchanged with the device. It is possible that some fields are only set or only get. This causes LLVM to emit warnings such as the following when building with W=1 [1]: drivers/net/ethernet/mellanox/mlxsw/core_acl_flex_actions.c:2022:1: warning: unused function 'mlxsw_afa_sampler_mirror_agent_get' The fact that some fields are only set or only get is very much intentional and not indicative of functions that need to be removed. Therefore, annotate the item helpers with '__maybe_unused' to suppress these warnings. [1] https://lkml.org/lkml/2021/9/29/685 Cc: Nathan Chancellor <nathan@kernel.org> Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Link: https://lore.kernel.org/r/20211008132315.90211-1-idosch@idosch.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-08net: tg3: fix redundant check of true expressionJean Sacren
Remove the redundant check of (tg3_asic_rev(tp) == ASIC_REV_5705) after it is checked to be true. Signed-off-by: Jean Sacren <sakiwit@gmail.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/20211008063147.1421-1-sakiwit@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-08qed: Fix compilation for CONFIG_QED_SRIOV undefined scenarioPrabhakar Kushwaha
This patch fixes below compliation error in case CONFIG_QED_SRIOV not defined. drivers/net/ethernet/qlogic/qed/qed_dev.c: In function ‘qed_fw_err_handler’: drivers/net/ethernet/qlogic/qed/qed_dev.c:2390:3: error: implicit declaration of function ‘qed_sriov_vfpf_malicious’; did you mean ‘qed_iov_vf_task’? [-Werror=implicit-function-declaration] qed_sriov_vfpf_malicious(p_hwfn, &data->err_data); ^~~~~~~~~~~~~~~~~~~~~~~~ qed_iov_vf_task drivers/net/ethernet/qlogic/qed/qed_dev.c: In function ‘qed_common_eqe_event’: drivers/net/ethernet/qlogic/qed/qed_dev.c:2410:10: error: implicit declaration of function ‘qed_sriov_eqe_event’; did you mean ‘qed_common_eqe_event’? [-Werror=implicit-function-declaration] return qed_sriov_eqe_event(p_hwfn, opcode, echo, data, ^~~~~~~~~~~~~~~~~~~ qed_common_eqe_event Fixes: fe40a830dcde ("qed: Update qed_hsi.h for fw 8.59.1.0") Reported-by: Linux Kernel Functional Testing <lkft@linaro.org> Cc: Naresh Kamboju <naresh.kamboju@linaro.org> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: Shai Malin <smalin@marvell.com> Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com> Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-08net: phy: micrel: ksz9131 led errata workaroundFrancesco Dolcini
Micrel KSZ9131 PHY LED behavior is not correct when configured in Individual Mode, LED1 (Activity LED) is in the ON state when there is no-link. Workaround this by setting bit 9 of register 0x1e after verifying that the LED configuration is Individual Mode. This issue is described in KSZ9131RNX Silicon Errata DS80000693B [*] and according to that it will not be corrected in a future silicon revision. [*] https://ww1.microchip.com/downloads/en/DeviceDoc/KSZ9131RNX-Silicon-Errata-and-Data-Sheet-Clarification-80000863B.pdf Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-08ppp: use the correct function to check if a netdev name is in useAntoine Tenart
A new helper to detect if a net device name is in use was added. Use it here as the return reference from __dev_get_by_name was discarded. Signed-off-by: Antoine Tenart <atenart@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-08bonding: use the correct function to check for netdev name collisionAntoine Tenart
A new helper to detect if a net device name is in use was added. Use it here as the return reference from __dev_get_by_name was discarded. Signed-off-by: Antoine Tenart <atenart@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-08net: enetc: add support for software TSOIoana Ciornei
This patch adds support for driver level TSO in the enetc driver using the TSO API. Beside using the usual tso_build_hdr(), tso_build_data() this specific implementation also has to compute the checksum, both IP and L4, for each resulted segment. This is because the ENETC controller does not support Tx checksum offload which is needed in order to take advantage of TSO. With the workaround for the ENETC MDIO erratum in place the Tx path of the driver is forced to lock/unlock for each skb sent. This is why, even though we are computing the checksum by hand we see the following improvement in TCP termination on the LS1028A SoC, on a single A72 core running at 1.3GHz: before: 1.63 Gbits/sec after: 2.34 Gbits/sec Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-08net: enetc: declare NETIF_F_HW_CSUM and do it in softwareIoana Ciornei
This is just a preparation patch for software TSO in the enetc driver. Unfortunately, ENETC does not support Tx checksum offload which would normally render TSO, even software, impossible. Declare NETIF_F_HW_CSUM as part of the feature set and do it at driver level using skb_csum_hwoffload_help() so that we can move forward and also add support for TSO in the next patch. Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-08ath11k: fix m68k and xtensa build failure in ath11k_peer_assoc_h_smps()Kalle Valo
Stephen reported that ath11k was failing to build on m68k and xtensa: In file included from <command-line>:0:0: In function 'ath11k_peer_assoc_h_smps', inlined from 'ath11k_peer_assoc_prepare' at drivers/net/wireless/ath/ath11k/mac.c:2362:2: include/linux/compiler_types.h:317:38: error: call to '__compiletime_assert_650' declared with attribute error: FIELD_GET: type of reg too small for mask _compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__) ^ include/linux/compiler_types.h:298:4: note: in definition of macro '__compiletime_assert' prefix ## suffix(); \ ^ include/linux/compiler_types.h:317:2: note: in expansion of macro '_compiletime_assert' _compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__) ^ include/linux/build_bug.h:39:37: note: in expansion of macro 'compiletime_assert' #define BUILD_BUG_ON_MSG(cond, msg) compiletime_assert(!(cond), msg) ^ include/linux/bitfield.h:52:3: note: in expansion of macro 'BUILD_BUG_ON_MSG' BUILD_BUG_ON_MSG((_mask) > (typeof(_reg))~0ull, \ ^ include/linux/bitfield.h:108:3: note: in expansion of macro '__BF_FIELD_CHECK' __BF_FIELD_CHECK(_mask, _reg, 0U, "FIELD_GET: "); \ ^ drivers/net/wireless/ath/ath11k/mac.c:2079:10: note: in expansion of macro 'FIELD_GET' smps = FIELD_GET(IEEE80211_HE_6GHZ_CAP_SM_PS, Fix the issue by using le16_get_bits() to specify the size explicitly. Fixes: 6f4d70308e5e ("ath11k: support SMPS configuration for 6 GHz") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Tested-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-08net: phylib: ensure phy device drivers do not match by DTRussell King (Oracle)
PHYLIB device drivers must match by either numerical PHY ID or by their .match_phy_device method. Matching by DT is not permitted. Link: https://lore.kernel.org/r/2b1dc053-8c9a-e3e4-b450-eecdfca3fe16@gmail.com Tested-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-08net: mdio: ensure the type of mdio devices match mdio driversRussell King (Oracle)
On the MDIO bus, we have PHYLIB devices and drivers, and we have non- PHYLIB devices and drivers. PHYLIB devices are MDIO devices that are wrapped with a struct phy_device. Trying to bind a MDIO device with a PHYLIB driver results in out-of- bounds accesses as we attempt to access struct phy_device members. So, let's prevent this by ensuring that the type of the MDIO device (indicated by the MDIO_DEVICE_FLAG_PHY flag) matches the type of the MDIO driver (indicated by the MDIO_DEVICE_IS_PHY flag.) Link: https://lore.kernel.org/r/2b1dc053-8c9a-e3e4-b450-eecdfca3fe16@gmail.com Tested-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-08qed: Initialize debug string arrayTim Gardner
Coverity complains of an uninitialized variable. CID 120847 (#1 of 1): Uninitialized scalar variable (UNINIT) 3. uninit_use_in_call: Using uninitialized value *sw_platform_str when calling qed_dump_str_param. [show details] 1344 offset += qed_dump_str_param(dump_buf + offset, 1345 dump, "sw-platform", sw_platform_str); Fix this by removing dead code that references sw_platform_str. Fixes: 6c95dd8f0aa1d ("qed: Update debug related changes") Cc: Ariel Elior <aelior@marvell.com> Cc: GR-everest-linux-l2@marvell.com Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Shai Malin <smalin@marvell.com> Cc: Omkar Kulkarni <okulkarni@marvell.com> Cc: Prabhakar Kushwaha <pkushwaha@marvell.com> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org (open list) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-08net: dsa: rtl8366rb: remove unneeded semicolonYang Li
Eliminate the following coccicheck warning: ./drivers/net/dsa/rtl8366rb.c:1348:2-3: Unneeded semicolon Reported-by: Abaci Robot <abaci@linux.alibaba.com> Signed-off-by: Yang Li <yang.lee@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-08ethernet: use platform_get_ethdev_address()Jakub Kicinski
Use the new platform_get_ethdev_address() helper for the cases where dev->dev_addr is passed in directly as the destination. @@ expression dev, net; @@ - eth_platform_get_mac_address(dev, net->dev_addr) + platform_get_ethdev_address(dev, net) Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-08Merge branch '100GbE' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue Tony Nguyen says: ==================== 100GbE Intel Wired LAN Driver Updates 2021-10-07 Michal Swiatkowski says: The following patch series introduces basic switchdev model support in ice driver. Implement the following blocks of switchdev framework: - VF port representors creation - control plane VSI definition - exception path (a. k. a. "slow-path") - to allow a virtual switch or linux bridge to receive any packet that doesn't match any hw filter - link state management of virtual ports - query virtual port statistics Hardware offload support in switchdev mode is out of scope of this patchset. Devlink interface is used to toggle between switchdev and legacy (the default) modes of the driver. --- Note: This series includes the use enum ice_status, however, we have patches in our queue to remove it from the driver [1]. We are working through the patches that precede the removal series. [1] https://patchwork.ozlabs.org/project/intel-wired-lan/list/?series=265957 ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-07Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski
No conflicts. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-07Merge tag 'armsoc-fixes-5.15' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC fixes from Arnd Bergmann: "This is a larger than normal update for Arm SoC specific code, most of it in device trees, but also drivers and the omap and at91/sama7 platforms: - There are four new entries to the MAINTAINERS file: Sven Peter and Alyssa Rosenzweig for Apple M1, Romain Perier for Mstar/sigmastar, and Vignesh Raghavendra for TI K3 - Build fixes to address randconfig warnings in sharpsl, dove, omap1, and qcom platforms as well as the scmi and op-tee subsystems - Regression fixes for missing CONFIG_FB and other options for several defconfigs - Several bug fixes for the newly added Microchip SAMA7 platform, mostly regarding power management - Missing SMP barriers to protect accesses to SCMI virtio device - Regression fixes for TI OMAP, including a boot-time hang on am335x. - Lots of bug fixes for NXP i.MX, mostly addressing incorrect settings in devicetree files, and one revert for broken suspend. - Fixes for ARM Juno/Vexpress devicetree files, addressing a couple of schema warnings. - Regression fixes for qualcomm SoC specific drivers and devicetree files, reverting an mdt_loader change and at least pastially reverting some of the 5.15 DTS changes, plus some minor bugfixes" * tag 'armsoc-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (64 commits) MAINTAINERS: Add Sven Peter as ARM/APPLE MACHINE maintainer MAINTAINERS: Add Alyssa Rosenzweig as M1 reviewer firmware: arm_scmi: Add proper barriers to scmi virtio device firmware: arm_scmi: Simplify spinlocks in virtio transport ARM: dts: omap3430-sdp: Fix NAND device node bus: ti-sysc: Use CLKDM_NOAUTO for dra7 dcan1 for errata i893 ARM: sharpsl_param: work around -Wstringop-overread warning ARM: defconfig: gemini: Restore framebuffer ARM: dove: mark 'putc' as inline ARM: omap1: move omap15xx local bus handling to usb.c MAINTAINERS: Add Vignesh to TI K3 platform maintainership arm64: dts: imx8m*-venice-gw7902: fix M2_RST# gpio ARM: imx6: disable the GIC CPU interface before calling stby-poweroff sequence arm64: dts: ls1028a: fix eSDHC2 node arm64: dts: imx8mm-kontron-n801x-som: do not allow to switch off buck2 ARM: dts: at91: sama7g5ek: to not touch slew-rate for SDMMC pins ARM: dts: at91: sama7g5ek: use proper slew-rate settings for GMACs ARM: at91: pm: preload base address of controllers in tlb ARM: at91: pm: group constants and addresses loading ARM: dts: at91: sama7g5ek: add suspend voltage for ddr3l rail ...
2021-10-07Merge tag 'scmi-fixes-5.15' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes SCMI fixes for v5.15 A few fixes addressing: - Kconfig dependency between VIRTIO and ARM_SCMI_PROTOCOL - Link-time error with __exit annotation for virtio_scmi_exit - Unnecessary nested irqsave/irqrestore spinlocks in virtio transport - Missing SMP barriers to protect accesses to SCMI virtio device * tag 'scmi-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux: firmware: arm_scmi: Add proper barriers to scmi virtio device firmware: arm_scmi: Simplify spinlocks in virtio transport firmware: arm_scmi: Remove __exit annotation firmware: arm_scmi: Fix virtio transport Kconfig dependency Link: https://lore.kernel.org/r/20211007102822.27886-1-sudeep.holla@arm.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-10-07Merge tag 'omap-for-v5.15/fixes-rc4' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes Fixes for omaps for v5.15 Few regression fixes for omaps for the v5.15-rc cycle. There is a fix for boot time hangs that can happen on some am335x devices that started when the pruss devicetree nodes were added. The other fixes are less critical: - Fix compiler warning for sysc_init_soc() that got recently introduced - Fix external abort for am335x pruss as otherwise some am335x will hang - Use CLKDM_NOAUTO quirk also for dra7 dcan1 - Fix older NAND device node regression for omap3-sdp * tag 'omap-for-v5.15/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: dts: omap3430-sdp: Fix NAND device node bus: ti-sysc: Use CLKDM_NOAUTO for dra7 dcan1 for errata i893 soc: ti: omap-prm: Fix external abort for am335x pruss bus: ti-sysc: Add break in switch statement in sysc_init_soc() Link: https://lore.kernel.org/r/pull-1633609552-789682@atomide.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-10-07ice: add port representor ethtool ops and statsWojciech Drewek
Introduce the following ethtool operations for VF's representor: -get_drvinfo -get_strings -get_ethtool_stats -get_sset_count -get_link In all cases, existing operations were used with minor changes which allow us to detect if ethtool op was called for representor. Only VF VSI stats will be available for representor. Implement ndo_get_stats64 for port representor. This will update VF VSI stats and read them. Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-10-07ice: switchdev slow pathGrzegorz Nitka
Slow path means allowing packet to go from uplink to representor and from representor to correct VF on Rx site and from VF to representor and to uplink on Tx site. To accomplish this driver, has to set correct Tx descriptor. When packet is sent from representor to VF, destination should be set to VF VSI. When packet is sent from uplink port destination should be uplink to bypass switch infrastructure and send packet outside. On Rx site driver should check source VSI field from Rx descriptor and based on that forward packed to correct netdev. To allow this there is a target netdevs table in control plane VSI struct. Co-developed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-10-07ice: rebuild switchdev when resetting all VFsGrzegorz Nitka
As resetting all VFs behaves mostly like creating new VFs also eswitch infrastructure has to be recreated. The easiest way to do that is to rebuild eswitch after resetting VFs. Implement helper functions to start and stop all representors queues. This is used to disable traffic on port representors. In rebuild path: - NAPI has to be disabled - eswitch environment has to be set up - new port representors have to be created, because the old one had pointer to not existing VFs - new control plane VSI ring should be remapped - NAPI hast to be enabled - rxdid has to be set to FLEX_NIC_2, because this descriptor id support source_vsi, which is needed on control plane VSI queues - port representors queues have to be started Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-10-07ice: enable/disable switchdev when managing VFsGrzegorz Nitka
Only way to enable switchdev is to create VFs when the eswitch mode is set to switchdev. Check if correct mode is set and enable switchdev in function which creating VFs. Disable switchdev when user change number of VFs to 0. Changing eswitch mode back to legacy when VFs are created in switchdev mode isn't allowed. As switchdev takes care of managing filter rules, adding new rules on VF is blocked. In case of resetting VF driver has to update pointer in ice_repr struct, because after reset VSI related things can change. Co-developed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
generated by cgit (git 2.34.1) at 2025-04-16 16:17:25 +0000