| Age | Commit message (Collapse) | Author |
|---|
|
The driver forgets to call pci_release_regions() in remove like that
in probe failure.
Add the missed call to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refer to the databook of DesignWare Cores Ethernet MAC Universal:
6.2.1.5 Register 4 (Transmit Descriptor List Address Register
If this register is not changed when the ST bit is set to 0, then
the DMA takes the descriptor address where it was stopped earlier.
The stmmac_tx_err() does zero indices to Tx descriptors, but does
not reset HW current Tx descriptor address. To fix inconsistency,
the base address of the Tx descriptors should be rewritten before
restarting Tx.
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The EEE support has not been enabled on ENETC, but it may connect
to a PHY which supports EEE and advertises EEE by default, while
its link partner also advertises EEE. If this happens, the PHY enters
low power mode when the traffic rate is low and causes packet loss.
This patch disables EEE advertisement by default for any PHY that
ENETC connects to, to prevent the above unwanted outcome.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sock_fprog_kern::len is in units of struct sock_filter, not bytes.
Fixes: 3e859adf3643 ("compat_ioctl: unify copy-in of ppp filters")
Reported-by: syzbot+eb853b51b10f1befa0b7@syzkaller.appspotmail.com
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, when set VF VLAN with command "ip link set <pf name>
vf <vf id> vlan <vlan id>", the VF ID 0 is handled as PF incorrectly,
which should be the first VF. This patch fixes it.
Fixes: 21e043cd8124 ("net: hns3: fix set port based VLAN for PF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, hns3_nic_maybe_stop_tx() uses skb_copy() to linearize a
SKB if the BD num required by the SKB does not meet the hardware
limitation, and it linearizes the SKB by allocating a new linearized SKB
and freeing the old SKB, if hns3_nic_maybe_stop_tx() returns -EBUSY
because there are no enough space in the ring to send the linearized
skb to hardware, the sch_direct_xmit() still hold reference to old SKB
and try to retransmit the old SKB when dev_hard_start_xmit() return
TX_BUSY, which may cause use after freed problem.
This patch fixes it by using __skb_linearize() to linearize the
SKB in hns3_nic_maybe_stop_tx().
Fixes: 51e8439f3496 ("net: hns3: add 8 BD limit for tx flow")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is timing window between ring_space checking and
netif_stop_subqueue when transmiting a SKB, and the TX BD
cleaning may be executed during the time window, which may
caused TX queue not restarted problem.
This patch fixes it by rechecking the ring_space after
netif_stop_subqueue to make sure TX queue is restarted.
Also, the ring->next_to_clean is updated even when pkts is
zero, because all the TX BD cleaned may be non-SKB, so it
needs to check if TX queue need to be restarted.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
for NET_SWITCHDEV
Replace "select NET_SWITCHDEV" vs "depends on NET_SWITCHDEV" to fix Kconfig
warning with CONFIG_COMPILE_TEST=y
WARNING: unmet direct dependencies detected for NET_SWITCHDEV
Depends on [n]: NET [=y] && INET [=n]
Selected by [y]:
- TI_CPSW_SWITCHDEV [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_TI [=y] && (ARCH_DAVINCI || ARCH_OMAP2PLUS || COMPILE_TEST [=y])
because TI_CPSW_SWITCHDEV blindly selects NET_SWITCHDEV even though
INET is not set/enabled, while NET_SWITCHDEV depends on INET.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: ed3525eda4c4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cio layer's intparm logic does not align itself well with how qeth
manages cmd IOs. When an active IO gets terminated via halt/clear, the
corresponding IRQ's intparm does not reflect the cmd buffer but rather
the intparm that was passed to ccw_device_halt() / ccw_device_clear().
This behaviour was recently clarified in
commit b91d9e67e50b ("s390/cio: fix intparm documentation").
As a result, qeth_irq() currently doesn't cancel a cmd that was
terminated via halt/clear. This primarily causes us to leak
card->read_cmd after the qeth device is removed, since our IO path still
holds a refcount for this cmd.
For qeth this means that we need to keep track of which IO is pending on
a device ('active_cmd'), and use this as the intparm when calling
halt/clear. Otherwise qeth_irq() can't match the subsequent IRQ to its
cmd buffer.
Since we now keep track of the _expected_ intparm, we can also detect
any mismatch; this would constitute a bug somewhere in the lower layers.
In this case cancel the active cmd - we effectively "lost" the IRQ and
should not expect any further notification for this IO.
Fixes: 405548959cc7 ("s390/qeth: add support for dynamically allocated cmds")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the RX path builds non-linear skbs, the packet headers can
currently spill over into page fragments. Depending on the packet type
and what fields we need to access in the headers, this could cause us
to go past the end of skb->data.
So for non-linear packets, copy precisely the length of the necessary
headers ('linear_len') into skb->data.
And don't copy more, upper-level protocols will peel whatever additional
packet headers they need.
Fixes: 4a71df50047f ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Depending on a packet's type, the RX path needs to access fields in the
packet headers and thus requires a minimum packet length.
Enforce this length when building the skb.
On the other hand a single runt packet is no reason to drop the whole
RX buffer. So just skip it, and continue processing on the next packet.
Fixes: 4a71df50047f ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 2b3e88ea6528 ("net: phy: improve phy state checking")
phy_start_aneg() expects phy state to be >= PHY_UP. Call phy_start()
before calling phy_start_aneg() during probe so that autonegotiation
is initiated.
As phy_start() takes care of calling phy_start_aneg(), drop the explicit
call to phy_start_aneg().
Network fails without this patch on Octeon TX.
Fixes: 2b3e88ea6528 ("net: phy: improve phy state checking")
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The referenced commit below allowed more than one hwmon device to be
created per SFP, which is definitely not what we want. Avoid this by
only creating the hwmon device just as we transition to WAITDEV state.
Fixes: 139d3a212a1f ("net: sfp: allow modules with slow diagnostics to probe")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When unbinding, we don't correctly tear down the module state, leaving
(for example) the hwmon registration behind. Ensure everything is
properly removed by sending a remove event at unbind.
Fixes: 6b0da5c9c1a3 ("net: sfp: track upstream's attachment state in state machine")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the user has specified their own RSS hash key, don't
lose it across queue resets such as DOWN/UP, MTU change,
and number of channels change. This is fixed by moving
the key initialization to a little earlier in the lif
creation.
Also, let's clean up the RSS config a little better on
the way down by setting it all to 0.
Fixes: aa3198819bea ("ionic: Add RSS support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ipv6_stub uses the ip6_dst_lookup function to allow other modules to
perform IPv6 lookups. However, this function skips the XFRM layer
entirely.
All users of ipv6_stub->ip6_dst_lookup use ip_route_output_flow (via the
ip_route_output_key and ip_route_output helpers) for their IPv4 lookups,
which calls xfrm_lookup_route(). This patch fixes this inconsistent
behavior by switching the stub to ip6_dst_lookup_flow, which also calls
xfrm_lookup_route().
This requires some changes in all the callers, as these two functions
take different arguments and have different return types.
Fixes: 5f81bd2e5d80 ("ipv6: export a stub for IPv6 symbols used by vxlan")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently a switch driver deinit frees the regmaps, but the PTP clock is
still out there, available to user space via /dev/ptpN. Any PTP
operation is a ticking time bomb, since it will attempt to use the freed
regmaps and thus trigger kernel panics:
[ 4.291746] fsl_enetc 0000:00:00.2 eth1: error -22 setting up slave phy
[ 4.291871] mscc_felix 0000:00:00.5: Failed to register DSA switch: -22
[ 4.308666] mscc_felix: probe of 0000:00:00.5 failed with error -22
[ 6.358270] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000088
[ 6.367090] Mem abort info:
[ 6.369888] ESR = 0x96000046
[ 6.369891] EC = 0x25: DABT (current EL), IL = 32 bits
[ 6.369892] SET = 0, FnV = 0
[ 6.369894] EA = 0, S1PTW = 0
[ 6.369895] Data abort info:
[ 6.369897] ISV = 0, ISS = 0x00000046
[ 6.369899] CM = 0, WnR = 1
[ 6.369902] user pgtable: 4k pages, 48-bit VAs, pgdp=00000020d58c7000
[ 6.369904] [0000000000000088] pgd=00000020d5912003, pud=00000020d5915003, pmd=0000000000000000
[ 6.369914] Internal error: Oops: 96000046 [#1] PREEMPT SMP
[ 6.420443] Modules linked in:
[ 6.423506] CPU: 1 PID: 262 Comm: phc_ctl Not tainted 5.4.0-03625-gb7b2a5dadd7f #204
[ 6.431273] Hardware name: LS1028A RDB Board (DT)
[ 6.435989] pstate: 40000085 (nZcv daIf -PAN -UAO)
[ 6.440802] pc : css_release+0x24/0x58
[ 6.444561] lr : regmap_read+0x40/0x78
[ 6.448316] sp : ffff800010513cc0
[ 6.451636] x29: ffff800010513cc0 x28: ffff002055873040
[ 6.456963] x27: 0000000000000000 x26: 0000000000000000
[ 6.462289] x25: 0000000000000000 x24: 0000000000000000
[ 6.467617] x23: 0000000000000000 x22: 0000000000000080
[ 6.472944] x21: ffff800010513d44 x20: 0000000000000080
[ 6.478270] x19: 0000000000000000 x18: 0000000000000000
[ 6.483596] x17: 0000000000000000 x16: 0000000000000000
[ 6.488921] x15: 0000000000000000 x14: 0000000000000000
[ 6.494247] x13: 0000000000000000 x12: 0000000000000000
[ 6.499573] x11: 0000000000000000 x10: 0000000000000000
[ 6.504899] x9 : 0000000000000000 x8 : 0000000000000000
[ 6.510225] x7 : 0000000000000000 x6 : ffff800010513cf0
[ 6.515550] x5 : 0000000000000000 x4 : 0000000fffffffe0
[ 6.520876] x3 : 0000000000000088 x2 : ffff800010513d44
[ 6.526202] x1 : ffffcada668ea000 x0 : ffffcada64d8b0c0
[ 6.531528] Call trace:
[ 6.533977] css_release+0x24/0x58
[ 6.537385] regmap_read+0x40/0x78
[ 6.540795] __ocelot_read_ix+0x6c/0xa0
[ 6.544641] ocelot_ptp_gettime64+0x4c/0x110
[ 6.548921] ptp_clock_gettime+0x4c/0x58
[ 6.552853] pc_clock_gettime+0x5c/0xa8
[ 6.556699] __arm64_sys_clock_gettime+0x68/0xc8
[ 6.561331] el0_svc_common.constprop.2+0x7c/0x178
[ 6.566133] el0_svc_handler+0x34/0xa0
[ 6.569891] el0_sync_handler+0x114/0x1d0
[ 6.573908] el0_sync+0x140/0x180
[ 6.577232] Code: d503201f b00119a1 91022263 b27b7be4 (f9004663)
[ 6.583349] ---[ end trace d196b9b14cdae2da ]---
[ 6.587977] Kernel panic - not syncing: Fatal exception
[ 6.593216] SMP: stopping secondary CPUs
[ 6.597151] Kernel Offset: 0x4ada54400000 from 0xffff800010000000
[ 6.603261] PHYS_OFFSET: 0xffffd0a7c0000000
[ 6.607454] CPU features: 0x10002,21806008
[ 6.611558] Memory Limit: none
And now that ocelot->ptp_clock is checked at exit, prevent a potential
error where ptp_clock_register returned a pointer-encoded error, which
we are keeping in the ocelot private data structure. So now,
ocelot->ptp_clock is now either NULL or a valid pointer.
Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As per linux can framework, driver not allowed to touch the skb memory
after can_put_echo_skb() call.
This patch fixes the same.
https://www.spinics.net/lists/linux-can/msg02199.html
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Reviewed-by: Appana Durga Kedareswara Rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When the CAN bus clock is provided from the clock wizard, clock wizard
driver may not be available when can driver probes resulting to the
error message "bus clock not found error".
As this error message is not very useful to the end user, skip printing
in the case of deferred probe.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Appana Durga Kedareswara Rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
USB completion handlers are called in atomic context and must
specifically not allocate memory using GFP_KERNEL.
Fixes: 9f2d3eae88d2 ("can: ucan: add driver for Theobroma Systems UCAN devices")
Cc: stable <stable@vger.kernel.org> # 4.19
Cc: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Cc: Martin Elshuber <martin.elshuber@theobroma-systems.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Slcan_open doesn't clean-up device which registration failed from the
slcan_devs device list. On next open this list is iterated and freed
device is accessed. Fix this by calling slc_free_netdev in error path.
Driver/net/can/slcan.c is derived from slip.c. Use-after-free error was
identified in slip_open by syzboz. Same bug is in slcan.c. Here is the
trace from the Syzbot slip report:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x197/0x210 lib/dump_stack.c:118
print_address_description.constprop.0.cold+0xd4/0x30b mm/kasan/report.c:374
__kasan_report.cold+0x1b/0x41 mm/kasan/report.c:506
kasan_report+0x12/0x20 mm/kasan/common.c:634
__asan_report_load8_noabort+0x14/0x20 mm/kasan/generic_report.c:132
sl_sync drivers/net/slip/slip.c:725 [inline]
slip_open+0xecd/0x11b7 drivers/net/slip/slip.c:801
tty_ldisc_open.isra.0+0xa3/0x110 drivers/tty/tty_ldisc.c:469
tty_set_ldisc+0x30e/0x6b0 drivers/tty/tty_ldisc.c:596
tiocsetd drivers/tty/tty_io.c:2334 [inline]
tty_ioctl+0xe8d/0x14f0 drivers/tty/tty_io.c:2594
vfs_ioctl fs/ioctl.c:46 [inline]
file_ioctl fs/ioctl.c:509 [inline]
do_vfs_ioctl+0xdb6/0x13e0 fs/ioctl.c:696
ksys_ioctl+0xab/0xd0 fs/ioctl.c:713
__do_sys_ioctl fs/ioctl.c:720 [inline]
__se_sys_ioctl fs/ioctl.c:718 [inline]
__x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718
do_syscall_64+0xfa/0x760 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fixes: ed50e1600b44 ("slcan: Fix memory leak in error path")
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: David Miller <davem@davemloft.net>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.4
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Merge updates from Andrew Morton:
"Incoming:
- a small number of updates to scripts/, ocfs2 and fs/buffer.c
- most of MM
I still have quite a lot of material (mostly not MM) staged after
linux-next due to -next dependencies. I'll send those across next week
as the preprequisites get merged up"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (135 commits)
mm/page_io.c: annotate refault stalls from swap_readpage
mm/Kconfig: fix trivial help text punctuation
mm/Kconfig: fix indentation
mm/memory_hotplug.c: remove __online_page_set_limits()
mm: fix typos in comments when calling __SetPageUptodate()
mm: fix struct member name in function comments
mm/shmem.c: cast the type of unmap_start to u64
mm: shmem: use proper gfp flags for shmem_writepage()
mm/shmem.c: make array 'values' static const, makes object smaller
userfaultfd: require CAP_SYS_PTRACE for UFFD_FEATURE_EVENT_FORK
fs/userfaultfd.c: wp: clear VM_UFFD_MISSING or VM_UFFD_WP during userfaultfd_register()
userfaultfd: wrap the common dst_vma check into an inlined function
userfaultfd: remove unnecessary WARN_ON() in __mcopy_atomic_hugetlb()
userfaultfd: use vma_pagesize for all huge page size calculation
mm/madvise.c: use PAGE_ALIGN[ED] for range checking
mm/madvise.c: replace with page_size() in madvise_inject_error()
mm/mmap.c: make vma_merge() comment more easy to understand
mm/hwpoison-inject: use DEFINE_DEBUGFS_ATTRIBUTE to define debugfs fops
autonuma: reduce cache footprint when scanning page tables
autonuma: fix watermark checking in migrate_balanced_pgdat()
...
|
|
Pull networking fixes from David Miller:
1) Fix several scatter gather list issues in kTLS code, from Jakub
Kicinski.
2) macb driver device remove has to kill the hresp_err_tasklet. From
Chuhong Yuan.
3) Several memory leak and reference count bug fixes in tipc, from Tung
Nguyen.
4) Fix mlx5 build error w/o ipv6, from Yue Haibing.
5) Fix jumbo frame and other regressions in r8169, from Heiner
Kallweit.
6) Undo some BUG_ON()'s and replace them with WARN_ON_ONCE and proper
error propagation/handling. From Paolo Abeni.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (24 commits)
openvswitch: remove another BUG_ON()
openvswitch: drop unneeded BUG_ON() in ovs_flow_cmd_build_info()
net: phy: realtek: fix using paged operations with RTL8105e / RTL8208
r8169: fix resume on cable plug-in
r8169: fix jumbo configuration for RTL8168evl
net: emulex: benet: indent a Kconfig depends continuation line
selftests: forwarding: fix race between packet receive and tc check
net: sched: fix `tc -s class show` no bstats on class with nolock subqueues
net: ethernet: ti: ale: ensure vlan/mdb deleted when no members
net/mlx5e: Fix build error without IPV6
selftests: pmtu: use -oneline for ip route list cache
tipc: fix duplicate SYN messages under link congestion
tipc: fix wrong timeout input for tipc_wait_for_cond()
tipc: fix wrong socket reference counter after tipc_sk_timeout() returns
tipc: fix potential memory leak in __tipc_sendmsg()
net: macb: add missed tasklet_kill
selftests: bpf: correct perror strings
selftests: bpf: test_sockmap: handle file creation failures gracefully
net/tls: use sg_next() to walk sg entries
net/tls: remove the dead inplace_crypto code
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Various fixes:
- Fix the PAT performance regression that downgraded write-combining
device memory regions to uncached.
- There's been a number of bugs in 32-bit double fault handling -
hopefully all fixed now.
- Fix an LDT crash
- Fix an FPU over-optimization that broke with GCC9 code
optimizations.
- Misc cleanups"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/pat: Fix off-by-one bugs in interval tree search
x86/ioperm: Save an indentation level in tss_update_io_bitmap()
x86/fpu: Don't cache access to fpu_fpregs_owner_ctx
x86/entry/32: Remove unused 'restore_all_notrace' local label
x86/ptrace: Document FSBASE and GSBASE ABI oddities
x86/ptrace: Remove set_segment_reg() implementations for current
x86/traps: die() instead of panicking on a double fault
x86/doublefault/32: Rewrite the x86_32 #DF handler and unify with 64-bit
x86/doublefault/32: Move #DF stack and TSS to cpu_entry_area
x86/doublefault/32: Rename doublefault.c to doublefault_32.c
x86/traps: Disentangle the 32-bit and 64-bit doublefault code
lkdtm: Add a DOUBLE_FAULT crash type on x86
selftests/x86/single_step_syscall: Check SYSENTER directly
x86/mm/32: Sync only to VMALLOC_END in vmalloc_sync_all()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- updates to Ilitech driver to support ILI2117
- face lift of st1232 driver to support MT-B protocol
- a new driver for i.MX system controller keys
- mpr121 driver now supports polling mode
- various input drivers have been switched away from input_polled_dev
to use polled mode of regular input devices
- other assorted cleanups and fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (70 commits)
Input: synaptics-rmi4 - fix various V4L2 compliance problems in F54
Input: synaptics - switch another X1 Carbon 6 to RMI/SMbus
Input: fix Kconfig indentation
Input: imx_sc_key - correct SCU message structure to avoid stack corruption
Input: ili210x - optionally show calibrate sysfs attribute
Input: ili210x - add resolution to chip operations structure
Input: ili210x - do not retrieve/print chip firmware version
Input: mms114 - use device_get_match_data
Input: ili210x - remove unneeded suspend and resume handlers
Input: ili210x - do not unconditionally mark touchscreen as wakeup source
Input: ili210x - define and use chip operations structure
Input: ili210x - do not set parent device explicitly
Input: ili210x - handle errors from input_mt_init_slots()
Input: ili210x - switch to using threaded IRQ
Input: ili210x - add ILI2117 support
dt-bindings: input: touchscreen: ad7879: generic node names in example
Input: ar1021 - fix typo in preprocessor macro name
Input: synaptics-rmi4 - simplify data read in rmi_f54_work
Input: kxtj9 - switch to using polled mode of input devices
Input: kxtj9 - switch to using managed resources
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"The highlight this cycle is continuing integration fixes for PowerPC
and some resulting optimizations.
Summary:
- Updates to better support vmalloc space restrictions on PowerPC
platforms.
- Cleanups to move common sysfs attributes to core 'struct
device_type' objects.
- Export the 'target_node' attribute (the effective numa node if pmem
is marked online) for regions and namespaces.
- Miscellaneous fixups and optimizations"
* tag 'libnvdimm-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (21 commits)
MAINTAINERS: Remove Keith from NVDIMM maintainers
libnvdimm: Export the target_node attribute for regions and namespaces
dax: Add numa_node to the default device-dax attributes
libnvdimm: Simplify root read-only definition for the 'resource' attribute
dax: Simplify root read-only definition for the 'resource' attribute
dax: Create a dax device_type
libnvdimm: Move nvdimm_bus_attribute_group to device_type
libnvdimm: Move nvdimm_attribute_group to device_type
libnvdimm: Move nd_mapping_attribute_group to device_type
libnvdimm: Move nd_region_attribute_group to device_type
libnvdimm: Move nd_numa_attribute_group to device_type
libnvdimm: Move nd_device_attribute_group to device_type
libnvdimm: Move region attribute group definition
libnvdimm: Move attribute groups to device type
libnvdimm: Remove prototypes for nonexistent functions
libnvdimm/btt: fix variable 'rc' set but not used
libnvdimm/pmem: Delete include of nd-core.h
libnvdimm/namespace: Differentiate between probe mapping and runtime mapping
libnvdimm/pfn_dev: Don't clear device memmap area during generic namespace probe
libnvdimm: Trivial comment fix
...
|
|
git://git.linaro.org/landing-teams/working/fujitsu/integration
Pull mailbox updates from Jassi Brar:
- omap : misc - catch error returned from pm_runtime_put_sync
- hisi : misc - drop .owner from platform_driver
- stm : change how wakeup is handled
- imx : fix - bailout on error and nuke correct irq
- imx : add support for imx7ulp platform
* tag 'mailbox-v5.5' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: imx: add support for imx v1 mu
dt-bindings: mailbox: imx-mu: add imx7ulp MU support
mailbox: imx: Clear the right interrupts at shutdown
mailbox: imx: Fix Tx doorbell shutdown path
mailbox: stm32-ipcc: Update wakeup management
mailbox: no need to set .owner platform_driver_register
mailbox/omap: Handle if CONFIG_PM is disabled
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc
Pull hwspinlock updates from Bjorn Andersson:
"This contains a number of cleanups to the core and several drivers, in
particular removing the requirement for drivers to implement
pm_runtime.
It also udpates the location of the git tree in MAINTAINERS"
* tag 'hwlock-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc:
hwspinlock: u8500_hsem: Remove redundant PM runtime implementation
hwspinlock: sprd: Remove redundant PM runtime implementation
hwspinlock: Let the PM runtime can be optional
hwspinlock: Remove BUG_ON() from the hwspinlock core
hwspinlock: sprd: Use devm_hwspin_lock_register() to register hwlock controller
hwspinlock: sprd: Use devm_add_action_or_reset() for calls to clk_disable_unprepare()
hwspinlock: sprd: Check the return value of clk_prepare_enable()
hwspinlock: sprd: Change to use devm_platform_ioremap_resource()
hwspinlock: u8500_hsem: Use devm_hwspin_lock_register() to register hwlock controller
hwspinlock: u8500_hsem: Use devm_kzalloc() to allocate memory
hwspinlock: u8500_hsem: Change to use devm_platform_ioremap_resource()
MAINTAINERS: hwspinlock: update git tree location
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc
Pull rpmsg updates from Bjorn Andersson:
"This contains a number of bug fixes to the GLINK transport driver, an
off-by-one in the GLINK smem driver and a memory leak fix in the rpmsg
char driver"
* tag 'rpmsg-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc:
rpmsg: Fix Kconfig indentation
rpmsg: char: Simplify 'rpmsg_eptdev_release()'
rpmsg: glink: Free pending deferred work on remove
rpmsg: glink: Don't send pending rx_done during remove
rpmsg: glink: Fix rpmsg_register_device err handling
rpmsg: glink: Put an extra reference during cleanup
rpmsg: glink: Fix use after free in open_ack TIMEOUT case
rpmsg: glink: Fix reuse intents memory leak issue
rpmsg: glink: Set tail pointer to 0 at end of FIFO
rpmsg: char: release allocated memory
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This adds support for booting the modem processor on Qualcomm MSM8998
and carries some cleanup up and bug fixes to the framework and the
stm32 driver"
* tag 'rproc-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc:
Revert "dt-bindings: remoteproc: stm32: add wakeup-source"
remoteproc: stm32: fix probe error case
remoteproc: stm32: wakeup the system by wdg irq
dt-bindings: remoteproc: stm32: add wakeup-source
remoteproc: Fix wrong rvring index computation
remoteproc: stm32: use workqueue to treat mailbox callback
remoteproc: fix argument 2 of rproc_mem_entry_init
remoteproc: qcom_q6v5_mss: Add support for MSM8998
dt-bindings: remoteproc: qcom: Add Q6v5 Modem PIL binding for MSM8998
remoteproc: debug: Remove unneeded NULL check
remoteproc: remove useless typedef
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"I2C has mostly driver updates this time.
The few noteworthy changes are: the core has now support for analog
and digital filters with at91 being the first user, a core addition to
replace the NULL returning i2c_new_probed_device() with an ERR_PTR
variant, and the pxa driver has finally being moved to use the generic
I2C slave interface. We have quite a significant number of reviews per
patch this time, so thank you to all involved!"
* 'i2c/for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (37 commits)
video: fbdev: matrox: convert to i2c_new_scanned_device
i2c: icy: convert to i2c_new_scanned_device
i2c: replace i2c_new_probed_device with an ERR_PTR variant
i2c: Fix Kconfig indentation
i2c: smbus: Don't filter out duplicate alerts
i2c: i801: Correct Intel Jasper Lake SOC naming
i2c: i2c-stm32f7: fix 10-bits check in slave free id search loop
i2c: iproc: Add i2c repeated start capability
i2c: remove helpers for ref-counting clients
i2c: tegra: Use dma_request_chan() directly for channel request
i2c: sh_mobile: Use dma_request_chan() directly for channel request
i2c: qup: Use dma_request_chan() directly for channel request
i2c: at91: Use dma_request_chan() directly for channel request
i2c: rcar: Remove superfluous call to clk_get_rate()
i2c: pxa: remove unused i2c-slave APIs
i2c: pxa: migrate to new i2c_slave APIs
i2c: cros-ec-tunnel: Make the device acpi compatible
i2c: stm32f7: report dma error during probe
i2c: icy: no need to populate address for scanned device
i2c: xiic: Fix kerneldoc warnings
...
|
|
Pull block fixes from Jens Axboe:
"I wasn't going to send this one off so soon, but unfortunately one of
the fixes from the previous pull broke the build on some archs. So I'm
sending this sooner rather than later. This contains:
- Add highmem.h include for io_uring, because of the kmap() additions
from last round. For some reason the build bot didn't spot this
even though it sat for days.
- Three minor ';' removals
- Add support for the Beurer CD-on-a-chip device
- Make io_uring work on MMU-less archs"
* tag 'for-linus-20191129' of git://git.kernel.dk/linux-block:
io_uring: fix missing kmap() declaration on powerpc
ataflop: Remove unneeded semicolon
block: sunvdc: Remove unneeded semicolon
drbd: Remove unneeded semicolon
io_uring: add mapping support for NOMMU archs
sr_vendor: support Beurer GL50 evo CD-on-a-chip devices.
cdrom: respect device capabilities during opening action
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Andy Shevchenko:
- New bootctl driver for Mellanox BlueField SoC.
- New driver to support System76 laptops.
- Temperature monitoring and fan control on Acer Aspire 7551 is now
supported.
- Previously the Huawei driver handled only hotkeys. After the
conversion to WMI it has been expanded to support newer laptop
models.
- Big refactoring of intel-speed-select tools allows to use it on Intel
CascadeLake-N systems.
- Touchscreen support for ezpad 6 m4 and Schneider SCT101CTM tablets
- Miscellaneous clean ups and fixes here and there.
* tag 'platform-drivers-x86-v5.5-1' of git://git.infradead.org/linux-platform-drivers-x86: (59 commits)
platform/x86: hp-wmi: Fix ACPI errors caused by passing 0 as input size
platform/x86: hp-wmi: Fix ACPI errors caused by too small buffer
platform/x86: intel_pmc_core: Add Comet Lake (CML) platform support to intel_pmc_core driver
platform/x86: intel_pmc_core: Fix the SoC naming inconsistency
platform/mellanox: Fix Kconfig indentation
tools/power/x86/intel-speed-select: Display TRL buckets for just base config level
tools/power/x86/intel-speed-select: Ignore missing config level
platform/x86: touchscreen_dmi: Add info for the ezpad 6 m4 tablet
tools/power/x86/intel-speed-select: Increment version
tools/power/x86/intel-speed-select: Use core count for base-freq mask
tools/power/x86/intel-speed-select: Support platform with limited Intel(R) Speed Select
tools/power/x86/intel-speed-select: Use Frequency weight for CLOS
tools/power/x86/intel-speed-select: Make CLOS frequency in MHz
tools/power/x86/intel-speed-select: Use mailbox for CLOS_PM_QOS_CONFIG
tools/power/x86/intel-speed-select: Auto mode for CLX
tools/power/x86/intel-speed-select: Correct CLX-N frequency units
tools/power/x86/intel-speed-select: Change display of "avx" to "avx2"
tools/power/x86/intel-speed-select: Extend command set for perf-profile
Add touchscreen platform data for the Schneider SCT101CTM tablet
platform/x86: intel_int0002_vgpio: Pass irqchip when adding gpiochip
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID updates from Jiri Kosina:
- Support for Logitech G15 (Hans de Goede)
- HID parser improvements, improving support for some devices; e.g.
Windows Precision Touchpad, products from Primax, etc. (Blaž
Hrastnik, Candle Sun)
- robustification of tablet mode support in google-whiskers driver
(Dmitry Torokhov)
- assorted small fixes, device-specific quirks and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (23 commits)
HID: rmi: Check that the RMI_STARTED bit is set before unregistering the RMI transport device
HID: quirks: remove hid-led devices from hid_have_special_driver
HID: Improve Windows Precision Touchpad detection.
HID: i2c-hid: Reset ALPS touchpads on resume
HID: i2c-hid: fix no irq after reset on raydium 3118
HID: logitech-hidpp: Silence intermittent get_battery_capacity errors
HID: i2c-hid: remove orphaned member sleep_delay
HID: quirks: Add quirk for HP MSU1465 PIXART OEM mouse
HID: core: check whether Usage Page item is after Usage ID items
HID: intel-ish-hid: Spelling s/diconnect/disconnect/
HID: google: Detect base folded usage instead of hard-coding whiskers
HID: logitech: Add depends on LEDS_CLASS to Logitech Kconfig entry
HID: lg-g15: Add support for the G510's M1-M3 and MR LEDs
HID: lg-g15: Add support for controlling the G510's RGB backlight
HID: lg-g15: Add support for the G510 keyboards' gaming keys
HID: lg-g15: Add support for the M1-M3 and MR LEDs
HID: lg-g15: Add keyboard and LCD backlight control
HID: Add driver for Logitech gaming keyboards (G15, G15 v2)
Input: Add event-codes for macro keys found on various keyboards
HID: hidraw: replace printk() with corresponding pr_xx() variant
...
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- support for NCT6116D
- several small fixes and improvements
* tag 'linux-watchdog-5.5-rc1' of git://www.linux-watchdog.org/linux-watchdog: (24 commits)
watchdog: jz4740: Drop dependency on MACH_JZ47xx
watchdog: jz4740: Use regmap provided by TCU driver
watchdog: jz4740: Use WDT clock provided by TCU driver
dt-bindings: watchdog: sama5d4_wdt: add microchip,sam9x60-wdt compatible
watchdog: sama5d4_wdt: cleanup the bit definitions
watchdog: sprd: Fix the incorrect pointer getting from driver data
watchdog: aspeed: Fix clock behaviour for ast2600
watchdog: imx7ulp: Fix reboot hang
watchdog: make nowayout sysfs file writable
watchdog: prevent deferral of watchdogd wakeup on RT
watchdog: imx7ulp: Use definitions instead of magic values
watchdog: imx7ulp: Remove inline annotations
watchdog: imx7ulp: Remove unused structure member
watchdog: imx7ulp: Pass the wdog instance inimx7ulp_wdt_enable()
watchdog: wdat_wdt: Spelling s/configrable/configurable/
watchdog: bd70528: Trivial function documentation fix
watchdog: cadence: Do not show error in case of deferred probe
watchdog: Fix the race between the release of watchdog_core_data and cdev
watchdog: sbc7240_wdt: Fix yet another -Wimplicit-fallthrough warning
watchdog: intel-mid_wdt: Add WATCHDOG_NOWAYOUT support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.5 kernel cycle
Core changes:
- Expose pull up/down flags for the GPIO character device to
userspace.
After clear input from the RaspberryPi and Beagle communities, it
has been established that prototyping, industrial automation and
make communities strongly need this feature, and as we want people
to use the character device, we have implemented the simple pull
up/down interface for GPIO lines.
This means we can specify that a (chip-specific) pull up/down
resistor can be enabled, but does not offer fine-grained control
such as cases where the resistance of the same pull resistor can be
controlled (yet).
- Introduce devm_fwnode_gpiod_get_index() and start to phase out the
old symbol devm_fwnode_get_index_gpiod_from_child().
- A bit of documentation clean-up work.
- Introduce a define for GPIO line directions and deploy it in all
GPIO drivers in the drivers/gpio directory.
- Add a special callback to populate pin ranges when cooperating with
the pin control subsystem and registering ranges as part of adding
a gpiolib driver and a gpio_irq_chip driver at the same time. This
is also deployed in the Intel Merrifield driver.
New drivers:
- RDA Micro GPIO controller.
- XGS-iproc GPIO driver.
Driver improvements:
- Wake event and debounce support on the Tegra 186 driver.
- Finalize the Aspeed SGPIO driver.
- MPC8xxx uses a normal IRQ handler rather than a chained handler"
* tag 'gpio-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (64 commits)
gpio: Add TODO item for regmap helper
Documentation: gpio: driver.rst: Fix warnings
gpio: of: Fix bogus reference to gpiod_get_count()
gpiolib: Grammar s/manager/managed/
gpio: lynxpoint: Setup correct IRQ handlers
MAINTAINERS: Replace my email by one @kernel.org
gpiolib: acpi: Make acpi_gpiochip_alloc_event always return AE_OK
gpio/mpc8xxx: fix qoriq GPIO reading
gpio: mpc8xxx: Don't overwrite default irq_set_type callback
gpiolib: acpi: Print pin number on acpi_gpiochip_alloc_event errors
gpiolib: fix coding style in gpiod_hog()
drm/bridge: ti-tfp410: switch to using fwnode_gpiod_get_index()
gpio: merrifield: Pass irqchip when adding gpiochip
gpio: merrifield: Add GPIO <-> pin mapping ranges via callback
gpiolib: Introduce ->add_pin_ranges() callback
gpio: mmio: remove untrue leftover comment
gpio: em: Use platform_get_irq() to obtain interrupts
gpio: tegra186: Add debounce support
gpio: tegra186: Program interrupt route mapping
gpio: tegra186: Derive register offsets from bank/port
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Add support for a "resource managed strongly uncachable ioremap"
call
- Provide a collection of MFD helper macros
- Remove mfd_clone_cell() from MFD core
- Add NULL de-reference protection in MFD core
- Remove superfluous function fd_platform_add_cell() from MFD core
- Honour Device Tree's request to disable a device
New Drivers:
- Add support for MediaTek MT6323 PMIC
New Device Support:
- Add support for Gemini Lake to Intel LPSS PCI
- Add support for Cherry Trail Crystal Cover PMIC to Intel SoC PMIC
CRC
- Add support for PM{I}8950 to Qualcomm SPMI PMIC
- Add support for U8420 to ST-Ericsson DB8500
- Add support for Comet Lake PCH-H to Intel LPSS PCI
New Functionality:
- Add support for requested supply clocks; madera-core
Fix-ups:
- Lower interrupt priority; rk808
- Use provided helpers (macros, group functions, defines); rk808,
ipaq-micro, ab8500-core, db8500-prcmu, mt6397-core, cs5535-mfd
- Only allocate IRQs on request; max77620
- Use simplified API; arizona-core
- Remove redundant and/or duplicated code; wm8998-tables, arizona,
syscon
- Device Tree binding fix-ups; madera, max77650, max77693
- Remove mfd_cell->id abuse hack; cs5535-mfd
- Remove only user of mfd_clone_cell(); cs5535-mfd
- Make resources static; rohm-bd70528
Bug Fixes:
- Fix product ID for RK818; rk808
- Fix Power Key; rk808
- Fix booting on the BananaPi; mt6397-core
- Endian fix-ups; twl.h
- Fix static error checker warnings; ti_am335x_tscadc"
* tag 'mfd-next-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (47 commits)
Revert "mfd: syscon: Set name of regmap_config"
mfd: ti_am335x_tscadc: Fix static checker warning
mfd: bd70528: Staticize bit value definitions
mfd: mfd-core: Honour Device Tree's request to disable a child-device
dt-bindings: mfd: max77693: Fix missing curly brace
mfd: intel-lpss: Add Intel Comet Lake PCH-H PCI IDs
mfd: db8500-prcmu: Support U8420-sysclk firmware
dt-bindings: mfd: max77650: Convert the binding document to yaml
mfd: mfd-core: Move pdev->mfd_cell creation back into mfd_add_device()
mfd: mfd-core: Remove usage counting for .{en,dis}able() call-backs
x86: olpc-xo1-sci: Remove invocation of MFD's .enable()/.disable() call-backs
x86: olpc-xo1-pm: Remove invocation of MFD's .enable()/.disable() call-backs
mfd: mfd-core: Remove mfd_clone_cell()
mfd: mfd-core: Protect against NULL call-back function pointer
mfd: cs5535-mfd: Register clients using their own dedicated MFD cell entries
mfd: cs5535-mfd: Request shared IO regions centrally
mfd: cs5535-mfd: Remove mfd_cell->id hack
mfd: cs5535-mfd: Use PLATFORM_DEVID_* defines and tidy error message
mfd: intel_soc_pmic_crc: Add "cht_crystal_cove_pmic" cell to CHT cells
mfd: madera: Add support for requesting the supply clocks
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"New Functionality:
- Add support for an enable GPIO; lm3630a_bl
- Add support for short circuit handling; qcom-wled
- Add support for automatic string detection; qcom-wled
Fix-ups:
- Update Device Tree bindings; lm3630a-backlight, led-backlight,
qcom-wled
- Constify; ipaq_micro_bl
- Optimise for CPU cycles; pwm_bl
- Coding style fix-ups; pwm_bl
- Trivial fix-ups (white space, comments, renaming); pwm_bl,
gpio_backlight, qcom-wled
- Kconfig dependency hacking; LCD_HP700
- Rename, refactor and add peripherals; pm8941-wled => qcom-wled
- Make use of GPIO look-up tables; tosa_bl, tosa_lcd
- Remove superfluous code; gpio_backlight
- Adapt GPIO direction handling; gpio_backlight
- Remove legacy use of platform data; gpio_backlight
Bug Fixes:
- Provide modules aliases; lm3630a_bl"
* tag 'backlight-next-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight: (32 commits)
backlight: qcom-wled: Fix spelling mistake "trigged" -> "triggered"
backlight: gpio: Pull gpio_backlight_initial_power_state() into probe
backlight: gpio: Use a helper variable for &pdev->dev
backlight: gpio: Remove unused fields from platform data
sh: ecovec24: don't set unused fields in platform data
backlight: gpio: Simplify the platform data handling
sh: ecovec24: add additional properties to the backlight device
backlight: gpio: Explicitly set the direction of the GPIO
backlight: gpio: Remove stray newline
backlight: gpio: Remove unneeded include
video: backlight: tosa: Use GPIO lookup table
backlight: qcom-wled: Add auto string detection logic
backlight: qcom-wled: Add support for short circuit handling
backlight: qcom-wled: Add support for WLED4 peripheral
backlight: qcom-wled: Restructure the driver for WLED3
backlight: qcom-wled: Rename PM8941* to WLED3
backlight: qcom-wled: Add new properties for PMI8998
backlight: qcom-wled: Restructure the qcom-wled bindings
backlight: qcom-wled: Rename pm8941-wled.c to qcom-wled.c
dt-bindings: backlight: lm3630a: Fix missing include
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fix from Linus Walleij:
"A oneliner fix adding the license to the new Intel pin controller,
avoiding a build-time warning"
* tag 'pinctrl-v5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: Fix warning by adding missing MODULE_LICENSE
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds
Pull LED updates from Pavel Machek:
"This contains usual small updates to drivers, and removal of PAGE_SIZE
limits on /sys/class/leds/<led>/trigger.
We should not be really having that many triggers; but with cpu
activity triggers we do, and we'll eventually need to fix it, but...
remove the limit for now"
* tag 'leds-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds: (26 commits)
leds: trigger: netdev: fix handling on interface rename
leds: an30259a: add a check for devm_regmap_init_i2c
leds: mlxreg: Fix possible buffer overflow
leds: pca953x: Use of_device_get_match_data()
leds: core: Fix leds.h structure documentation
leds: core: Fix devm_classdev_match to reference correct structure
leds: core: Remove extern from header
leds: lm3601x: Convert class registration to device managed
leds: flash: Add devm_* functions to the flash class
leds: flash: Remove extern from the header file
leds: flash: Convert non extended registration to inline
leds: Kconfig: Be consistent with the usage of "LED"
leds: remove PAGE_SIZE limit of /sys/class/leds/<led>/trigger
leds: tlc591xx: update the maximum brightness
leds: lm3692x: Use flags from LM3692X_BRT_CTRL
leds: lm3692x: Use flags from LM3692X_BOOST_CTRL
leds: lm3692x: Handle failure to probe the regulator
leds: lm3692x: Don't overwrite return value in error path
leds: lm3692x: Print error value on dev_err
leds: tlc591xx: use devm_led_classdev_register_ext()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This merge window we have one small clk provider API in the core
framework and then a bunch of driver updates and a handful of new
drivers. In terms of diffstat the Qualcomm and Amlogic drivers are
high up there because of all the clk data introcued by new drivers.
The Nvidia Tegra driver had a lot of work done this cycle too to
support suspend/resume and memory controllers. And the OMAP clk driver
got proper clk and reset handling in place.
Rounding out the patches are various updates to remove unused data,
mark things static, correct incorrect data in drivers, etc. All the
little things that improve drivers and maintain code health. I will
point out that there's a patch in here for the GPIO clk driver, that
almost nobody uses, which changes behavior and causes clk_set_rate()
to try to change the GPIO gate clk's parent. Other than that things
are fairly well SoC specific here.
Core:
- Add a clk provider API to get current parent index
- Plug a memory leak in clk_unregister() path
New Drivers:
- CGU in Ingenix X1000
- Bitmain BM1880 clks
- Qualcomm MSM8998 GPU clk controllers
- Qualcomm SC7180 GCC and RPMH clk controllers
- Qualcomm QCS404 Q6SSTOP clk controllers
- Add support for the Renesas R-Car M3-W+ (r8a77961) SoC
- Add support for the Renesas RZ/G2N (r8a774b1) SoC
- Add Tegra20/30 External Memory Clock (EMC) support
Updates:
- Make gpio gate clks propagate rate setting up to parent
- Prepare Armada 3700 for suspend to RAM by moving PCIe
suspend/resume priority
- Drop unused variables, enums, etc. in various clk drivers
- Convert various drivers to use devm_platform_ioremap_resource()
- Use struct_size() some more in various clk drivers
- Improve Rockchip px30 clk tree
- Add suspend/resume support to Tegra210 clk driver
- Reimplement SOR clks on earlier Tegra SoCs, helping HDMI and DP
- Allwinner DT exports and H6 clk tree fixes
- Proper clk and reset handling for OMAP SoCs
- Revamped TI divider clk to clamp max divider
- Make 1443X/1416X PLL clock structure common for reusing among i.MX8
SoCs
- Drop IMX7ULP_CLK_MIPI_PLL clock, it shouldn't be used
- Add VIDEO2_PLL clock for imx8mq
- Add missing gate clock for pll1/2 fixed dividers on i.MX8 SoCs
- Add sm1 support in the Amlogic audio clock controller
- Switch some clocks on R-Car Gen2/3 to .determine_rate()
- Remove Renesas R-Car Gen2 legacy DT clock support
- Improve arithmetic divisions on Renesas R-Car Gen2 and Gen3
- Improve Renesas R-Car Gen3 SD clock handling
- Add rate table for Samsung exynos542x GPU and VPLL clks
- Fix potential CPU performance degradation after system
suspend/resume cycle on exynos542x SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (160 commits)
clk: aspeed: Add RMII RCLK gates for both AST2500 MACs
MAINTAINERS: Add entry for BM1880 SoC clock driver
clk: Add common clock driver for BM1880 SoC
dt-bindings: clock: Add devicetree binding for BM1880 SoC
clk: Add clk_hw_unregister_composite helper function definition
clk: Zero init clk_init_data in helpers
clk: ingenic: Allow drivers to be built with COMPILE_TEST
MAINTAINERS: Update section for Ux500 clock drivers
clk: mark clk_disable_unused() as __init
clk: Fix memory leak in clk_unregister()
clk: Ingenic: Add CGU driver for X1000.
dt-bindings: clock: Add X1000 bindings.
clk: tegra: Use match_string() helper to simplify the code
clk: pxa: fix one of the pxa RTC clocks
clk: sprd: Use IS_ERR() to validate the return value of syscon_regmap_lookup_by_phandle()
clk: armada-xp: remove unused code
clk: tegra: Fix build error without CONFIG_PM_SLEEP
clk: tegra: Add missing stubs for the case of !CONFIG_PM_SLEEP
clk: tegra: Optimize PLLX restore on Tegra20/30
clk: tegra: Add suspend and resume support on Tegra210
...
|
|
git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground
Pull removal of most of fs/compat_ioctl.c from Arnd Bergmann:
"As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need
support for time64_t.
In completely unrelated work, I spent time on cleaning up parts of
this file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the
rest of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which
is the scsi ioctl handlers. I have patches for those as well, but they
need more testing or possibly a rewrite"
* tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground: (42 commits)
scsi: sd: enable compat ioctls for sed-opal
pktcdvd: add compat_ioctl handler
compat_ioctl: move SG_GET_REQUEST_TABLE handling
compat_ioctl: ppp: move simple commands into ppp_generic.c
compat_ioctl: handle PPPIOCGIDLE for 64-bit time_t
compat_ioctl: move PPPIOCSCOMPRESS to ppp_generic
compat_ioctl: unify copy-in of ppp filters
tty: handle compat PPP ioctls
compat_ioctl: move SIOCOUTQ out of compat_ioctl.c
compat_ioctl: handle SIOCOUTQNSD
af_unix: add compat_ioctl support
compat_ioctl: reimplement SG_IO handling
compat_ioctl: move WDIOC handling into wdt drivers
fs: compat_ioctl: move FITRIM emulation into file systems
gfs2: add compat_ioctl support
compat_ioctl: remove unused convert_in_user macro
compat_ioctl: remove last RAID handling code
compat_ioctl: remove /dev/raw ioctl translation
compat_ioctl: remove PCI ioctl translation
compat_ioctl: remove joystick ioctl translation
...
|
|
It was reported [0] that since the referenced commit a warning is
triggered in phylib that complains about paged operations being used
with a PHY driver that doesn't support this. The commit isn't wrong,
just for one chip version (RTL8105e) no dedicated PHY driver exists
yet. So add the missing PHY driver.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=202103
Fixes: 3a129e3f9ac4 ("r8169: switch to phylib functions in more places")
Reported-by: jhdskag3 <jhdskag3@tutanota.com>
Tested-by: jhdskag3 <jhdskag3@tutanota.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was reported [0] that network doesn't wake up on cable plug-in with
certain chip versions. Reason is that on these chip versions the PHY
doesn't detect cable plug-in when being in power-down mode. So prevent
the PHY from powering down if WoL is enabled.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=202103
Fixes: 95fb8bb3181b ("net: phy: force phy suspend when calling phy_stop")
Reported-by: jhdskag3 <jhdskag3@tutanota.com>
Tested-by: jhdskag3 <jhdskag3@tutanota.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alan reported [0] that network is broken since the referenced commit
when using jumbo frames. This commit isn't wrong, it just revealed
another issue that has been existing before. According to the vendor
driver the RTL8168e-specific jumbo config doesn't apply for RTL8168evl.
[0] https://lkml.org/lkml/2019/11/30/119
Fixes: 4ebcb113edcc ("r8169: fix jumbo packet handling on resume from suspend")
Reported-by: Alan J. Wylie <alan@wylie.me.uk>
Tested-by: Alan J. Wylie <alan@wylie.me.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__online_page_set_limits() is a dummy function - remove it and all
callers.
Link: http://lkml.kernel.org/r/8e1bc9d3b492f6bde16e95ebc1dee11d6aefabd7.1567889743.git.jrdr.linux@gmail.com
Link: http://lkml.kernel.org/r/854db2cf8145d9635249c95584d9a91fd774a229.1567889743.git.jrdr.linux@gmail.com
Link: http://lkml.kernel.org/r/9afe6c5a18158f3884a6b302ac2c772f3da49ccc.1567889743.git.jrdr.linux@gmail.com
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The mem_sysfs_mutex isn't really helpful. Also, it's not really clear
what the mutex protects at all.
The device lists of the memory subsystem are protected separately. We
don't need that mutex when looking up. creating, or removing
independent devices. find_memory_block_by_id() will perform locking on
its own and grab a reference of the returned device.
At the time memory_dev_init() is called, we cannot have concurrent
hot(un)plug operations yet - we're still fairly early during boot. We
don't need any locking.
The creation/removal of memory block devices should be protected on a
higher level - especially using the device hotplug lock to avoid
documented issues (see Documentation/core-api/memory-hotplug.rst) - or
if that is reworked, using similar locking.
Protecting in the context of these functions only doesn't really make
sense. Especially, if we would have a situation where the same memory
blocks are created/deleted at the same time, there is something horribly
going wrong (imagining adding/removing a DIMM at the same time from two
call paths) - after the functions succeeded something else in the
callers would blow up (e.g., create_memory_block_devices() succeeded but
there are no memory block devices anymore).
All relevant call paths (except when adding memory early during boot via
ACPI, which is now documented) hold the device hotplug lock when adding
memory, and when removing memory. Let's document that instead.
Add a simple safety net to create_memory_block_devices() in case we
would actually remove memory blocks while adding them, so we'll never
dereference a NULL pointer. Simplify memory_dev_init() now that the
lock is gone.
Link: http://lkml.kernel.org/r/20190925082621.4927-1-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Oscar Salvador <osalvador@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Let's use the generic onlining function - which will now also take care
of calling kernel_map_pages().
Link: http://lkml.kernel.org/r/20190909114830.662-3-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Sasha Levin <sashal@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Oscar Salvador <osalvador@suse.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Qian Cai <cai@lca.pw>
Cc: Wei Yang <richard.weiyang@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently soft_offline_page() receives struct page, and its sibling
memory_failure() receives pfn. This discrepancy looks weird and makes
precheck on pfn validity tricky. So let's align them.
Link: http://lkml.kernel.org/r/20191016234706.GA5493@www9186uo.sakura.ne.jp
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Cc: David Hildenbrand <david@redhat.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Oscar Salvador <osalvador@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There is a version 1.0 MU on i.MX7ULP platform.
One new version ID register is added, and it's offset is 0.
TRn registers are defined at the offset 0x20 ~ 0x2C.
RRn registers are defined at the offset 0x40 ~ 0x4C.
SR/CR registers are defined at 0x60/0x64.
Extend this driver to support it.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Suggested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
