| Age | Commit message (Collapse) | Author |
|---|
|
The GART aperture size can be bigger than 4GB. Therefore the offset
used in amdgpu_gart_bind and amdgpu_gart_unbind must be 64-bit.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Remove the hcd after checking for the xhci last quirks, not before.
This caused a hang on a Alpine Ridge xhci based maching which remove
the whole xhci controller when unplugging the last usb device
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After a device is disconnected, xhci_stop_device() will be invoked
in xhci_bus_suspend().
Also the "disconnect" IRQ will have ISR to invoke
xhci_free_virt_device() in this sequence.
xhci_irq -> xhci_handle_event -> handle_cmd_completion ->
xhci_handle_cmd_disable_slot -> xhci_free_virt_device
If xhci->devs[slot_id] has been assigned to NULL in
xhci_free_virt_device(), then virt_dev->eps[i].ring in
xhci_stop_device() may point to an invlid address to cause kernel
panic.
virt_dev = xhci->devs[slot_id];
:
if (virt_dev->eps[i].ring && virt_dev->eps[i].ring->dequeue)
[] Unable to handle kernel paging request at virtual address 00001a68
[] pgd=ffffffc001430000
[] [00001a68] *pgd=000000013c807003, *pud=000000013c807003,
*pmd=000000013c808003, *pte=0000000000000000
[] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[] CPU: 0 PID: 39 Comm: kworker/0:1 Tainted: G U
[] Workqueue: pm pm_runtime_work
[] task: ffffffc0bc0e0bc0 ti: ffffffc0bc0ec000 task.ti:
ffffffc0bc0ec000
[] PC is at xhci_stop_device.constprop.11+0xb4/0x1a4
This issue is found when running with realtek ethernet device
(0bda:8153).
Signed-off-by: Jim Lin <jilin@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Enqueue the first TRB even if full_len is zero.
Without this "adb install <apk>" freezes the system.
Signed-off-by: Alban Browaeys <alban.browaeys@gmail.com>
Fixes: 86065c2719a5 ("xhci: don't rely on precalculated value of needed trbs in the enqueue loop")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix "Command completion event does not match command" errors by always
handling the command ring stopped events.
The command ring stopped event is generated as a result of aborting
or stopping the command ring with a register write. It is not caused
by a command in the command queue, and thus won't have a matching command
in the comman list.
Solve it by handling the command ring stopped event before checking for a
matching command.
In most command time out cases we abort the command ring, and get
a command ring stopped event. The events command pointer will point at
the current command ring dequeue, which in most cases matches the timed
out command in the command list, and no error messages are seen.
If we instead get a command aborted event before the command ring stopped
event, the abort event will increse the command ring dequeue pointer, and
the following command ring stopped events command pointer will point at the
next, not yet queued command. This case triggered the error message
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
device pointers passed to DMA API
Runtime warning occurs if DMA-API debug feature is enabled that would be
raised by pointers passed to DMA API as arguments to inconsistent struct
device objects, so that the patch makes them usage aligned between DMA
operations such as dma_map_*() and dma_unmap_*() to eliminate the warning.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
enabled properly
Commit 08ef55c6f257acf3bdc6940813f80e8f0f5d90ec
("net-next: mediatek: fix gigabit and flow control advertisement")
had supported proper flow control settings for GMAC1. But for GMAC0,
1.GMAC0 shares the common logic with GMAC1 inside mtk_phy_link_adjust()
to adapt various settings for the target phy.
2.GMAC0 uses fixed-phy to connect to a builtin gigabit switch with
fixed link speed as commit 0c72c50f6f93b0c3daa9ea35d89ab3a933c7b5a0
("net-next: mediatek: add fixed-phy support") describes.
3.However, fixed-phy doesn't enable SUPPORTED_Pause & SUPPORTED_Asym_Pause
supported flag on default that would cause mtk_phy_link_adjust() not to
enable flow control setting on GMAC0 properly and cause packet dropped
when high traffic.
Due to these reasons, the patch adds SUPPORTED_Pause & SUPPORTED_Asym_Pause
supported flags on fixed-phy used by the driver to have proper handling on
the both GMAC with the shared common logic.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch fixes up the incorrect setup of reduced MII (RMII) on GMAC
and adds the supplement for the setup of reverse MII (REVMII) on GMAC
, and rearranges the error handling for invalid PHY argument.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add missing platform_set_drvdata() in tps65217_charger_probe(), otherwise
calling platform_get_drvdata() in remove returns NULL.
This is detected by Coccinelle semantic patch.
Fixes: 3636859b280c ("power_supply: Add support for tps65217-charger")
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Bonding driver sets IFF_BONDING on both master (the bonding device) and
slave (the real NIC) devices and in netvsc_netdev_event() we want to skip
master devices only. Currently, there is an uncertainty when a slave
interface is removed: if bonding module comes first in netdev_chain it
clears IFF_BONDING flag on the netdev and netvsc_netdev_event() correctly
handles NETDEV_UNREGISTER event, but in case netvsc comes first on the
chain it sees the device with IFF_BONDING still attached and skips it. As
we still hold vf_netdev pointer to the device we crash on the next inject.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We're not guaranteed to see NETDEV_REGISTER/NETDEV_UNREGISTER notifications
only once per VF but we increase/decrease module refcount unconditionally.
Check vf_netdev to make sure we don't take/release it twice. We presume
that only one VF per netvsc device may exist.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We reset vf_inject on VF going down (netvsc_vf_down()) but we don't on
VF removal (netvsc_unregister_vf()) so vf_inject stays 'true' while
vf_netdev is already NULL and we're trying to inject packets into NULL
net device in netvsc_recv_callback() causing kernel to crash.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Here is a deadlock scenario:
- netvsc_vf_up() schedules netvsc_notify_peers() work and quits.
- netvsc_vf_down() runs before netvsc_notify_peers() gets executed. As it
is being executed from netdev notifier chain we hold rtnl lock when we
get here.
- we enter while (atomic_read(&net_device_ctx->vf_use_cnt) != 0) loop and
wait till netvsc_notify_peers() drops vf_use_cnt.
- netvsc_notify_peers() starts on some other CPU but netdev_notify_peers()
will hang on rtnl_lock().
- deadlock!
Instead of introducing additional synchronization I suggest we drop
gwrk.dwrk completely and call NETDEV_NOTIFY_PEERS directly. As we're
acting under rtnl lock this is legitimate.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
struct netvsc_device is not suitable for storing VF information as this
structure is being destroyed on MTU change / set channel operation (see
rndis_filter_device_remove()). Move all VF related stuff to struct
net_device_context which is persistent.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- Some functions defined in a header file for the mediatek driver were
not marked inline. Fix that oversight.
- Fix a potential crash in the ARM64 dma-mapping code when freeing a
partially initialized domain.
- Another fix for ARM64 dma-mapping to respect IOMMU mapping
constraints when allocating IOVA addresses.
* tag 'iommu-fixes-v4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/dma: Respect IOMMU aperture when allocating
iommu/dma: Don't put uninitialised IOVA domains
iommu/mediatek: Mark static functions in headers inline
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC fix from Borislav Petkov:
"A fix to sb_edac correcting channel reporting on Knights Landing"
* tag 'edac_fixes_for_4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC, sb_edac: Fix channel reporting on Knights Landing
|
|
The called of_graph_get_next_endpoint() already decrements the refcount
of the prev node, so it is wrong to do it again in the calling function.
Use the for_each_endpoint_of_node() helper to interate through the
endpoint OF nodes, which already does the right thing and simplifies
the code a bit.
Fixes: 8ccd0d0ca041
(of: add helper for getting endpoint node of specific identifiers)
Cc: stable@vger.kernel.org
Reported-by: David Jander <david@protonic.nl>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
This fixes the "BOGUS urb xfer" warning logged by usb_submit_urb().
Signed-off-by: Gavin Li <git@thegavinli.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Increase mempool size from 16 to 64 entries. This increase improves
swap on dm-crypt performance.
When swapping to dm-crypt, all available memory is temporarily exhausted
and dm-crypt can only use the mempool reserve.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Use local_irq_save() to disable preemption before calling
this_cpu_ptr().
Reported-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Fixes: b0b477c7e0dd ("dm round robin: use percpu 'repeat_count' and 'current_path'")
Cc: stable@vger.kernel.org # 4.6+
Suggested-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Both the fence and event alloc are safe to be done without holding the GPU
lock, as they either don't need any locking (fences) or are protected by
their own lock (events).
This solves a bad locking interaction between the submit path and the
recover worker. If userspace manages to exhaust all available events while
the GPU is hung, the submit will wait for events to become available
holding the GPU lock. The recover worker waits for this lock to become
available before trying to recover the GPU which frees up the allocated
events. Essentially both paths are deadlocked until the submit path
times out waiting for available events, failing the submit that could
otherwise be handled just fine if the recover worker had the chance to
bring the GPU back in a working state.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
|
|
git://git.pengutronix.de/git/pza/linux into drm-fixes
mediatek-drm build dependency fixes
- add COMMON_CLK dependency for mipi-tx PLL
- add OF dependency for mtk_drm_drv
- add ARM_SMCCC dependency for mtk-hdmi
* tag 'mediatek-drm-fixes-2016-08-12' of git://git.pengutronix.de/git/pza/linux:
drm/mediatek: add ARM_SMCCC dependency
drm/mediatek: add CONFIG_OF dependency
drm/mediatek: add COMMON_CLK dependency
|
|
In mlxsw_sp_router_fib4_add_info_destroy(), the fib_entry pointer is used
after it has been freed by mlxsw_sp_fib_entry_destroy(). Use a temporary
variable to fix this.
Fixes: 61c503f976b5449e ("mlxsw: spectrum_router: Implement fib4 add/del switchdev obj ops")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal updates from Zhang Rui:
- Fix a race condition when updating cooling device, which may lead to
a situation where a thermal governor never updates the cooling
device. From Michele Di Giorgio.
- Fix a zero division error when disabling the forced idle injection
from the intel powerclamp. From Petr Mladek.
- Add suspend/resume callback for intel_pch_thermal thermal driver.
From Srinivas Pandruvada.
- Another two fixes for clocking cooling driver and hwmon sysfs I/F.
From Michele Di Giorgio and Kuninori Morimoto.
[ Hmm. That suspend/resume callback for intel_pch_thermal doesn't look
like a fix, but I'm letting it slide.. - Linus ]
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: clock_cooling: Fix missing mutex_init()
thermal: hwmon: EXPORT_SYMBOL_GPL for thermal hwmon sysfs
thermal: fix race condition when updating cooling device
thermal/powerclamp: Prevent division by zero when counting interval
thermal: intel_pch_thermal: Add suspend/resume callback
|
|
There is only one waiter for the completion, therefore there
is no need to use complete_all(). Let's make that clear by
using complete() instead of complete_all().
The usage pattern of the completion is:
meson_i2c_xfer_msg()
reinit_completion()
...
/* Start the transfer */
...
wait_for_completion_timeout()
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
There is only one waiter for the completion, therefore there
is no need to use complete_all(). Let's make that clear by
using complete() instead of complete_all().
The usage pattern of the completion is:
brcmstb_send_i2c_cmd()
reinit_completion()
...
/* initiate transfer by setting iic_enable */
...
brcmstb_i2c_wait_for_completion()
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Reviewed-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
There is only one waiter for the completion, therefore there
is no need to use complete_all(). Let's make that clear by
using complete() instead of complete_all().
The usage pattern of the completion is:
bcm_kona_send_i2c_cmd()
reinit_completion()
...
bcm_kona_i2c_send_cmd_to_ctrl()
...
wait_for_completion_timeout()
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Tim Kryger <tim.kryger@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
There is only one waiter for the completion, therefore there
is no need to use complete_all(). Let's make that clear by
using complete() instead of complete_all().
The usage pattern of the completion is:
bcm_iproc_i2c_xfer_single_msg()
reinit_completion()
...
(activate the transfer)
...
wait_for_completion_timeout()
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The "alternative command" feature was introduced with sama5d2 SoCs.
Its purpose is to let the hardware i2c controller automatically send the
STOP condition on the i2c bus at the end of a data transfer.
Without this feature, the i2c driver has to write the 'STOP' bit into the
Control Register so the hardware i2c controller is triggered to send the
STOP condition on the bus.
Using the "alternative command" feature requires to set the transfer data
length into the 8bit DATAL field of the Alternative Command Register.
Hence only data transfers up to 255 bytes can take advantage of the
"alternative command" feature. For greater data transfer sizes, the driver
should use the previous implementation, when the "alternative command"
support was not implemented yet.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
clk_disable_unprepare() is missed on failure paths in ocores_i2c_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
cros_ec_cmd_xfer returns success status if the command transport
completes successfully, but the execution result is incorrectly ignored.
In many cases, the execution result is assumed to be successful, leading
to ignored errors and operating on uninitialized data.
We've recently introduced the cros_ec_cmd_xfer_status() helper to avoid these
problems. Let's use it.
[Regarding the 'Fixes' tag; there is significant refactoring since the driver's
introduction, but the underlying logical error exists throughout I believe]
Fixes: 9d230c9e4f4e ("i2c: ChromeOS EC tunnel driver")
Cc: <stable@vger.kernel.org> # 9798ac6d32c1 mfd: cros_ec: Add cros_ec_cmd_xfer_status() helper
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
We also need to revert the dynamic OF change, so we get a consistent
state again. Otherwise, we might have two devices enabled e.g. after
pinctrl setup fails.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- support for nr_cpus= command line argument (maxcpus was previously
changed to allow secondary CPUs to be hot-plugged)
- ARM PMU interrupt handling fix
- fix potential TLB conflict in the hibernate code
- improved handling of EL1 instruction aborts (better error reporting)
- removal of useless jprobes code for stack saving/restoring
- defconfig updates
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: defconfig: enable CONFIG_LOCALVERSION_AUTO
arm64: defconfig: add options for virtualization and containers
arm64: hibernate: handle allocation failures
arm64: hibernate: avoid potential TLB conflict
arm64: Handle el1 synchronous instruction aborts cleanly
arm64: Remove stack duplicating code from jprobes
drivers/perf: arm-pmu: Fix handling of SPI lacking "interrupt-affinity" property
drivers/perf: arm-pmu: convert arm_pmu_mutex to spinlock
arm64: Support hard limit of cpu count by nr_cpus
|
|
The idea for type_check in dev_get_nest_level() was to count the number
of nested devices of the same type (currently, only macvlan or vlan
devices).
This prevented the false positive lockdep warning on configurations such
as:
eth0 <--- macvlan0 <--- vlan0 <--- macvlan1
However, this doesn't prevent a warning on a configuration such as:
eth0 <--- macvlan0 <--- vlan0
eth1 <--- vlan1 <--- macvlan1
In this case, all the locks end up with a nesting subclass of 1, so
lockdep thinks that there is still a deadlock:
- in the first case we have (macvlan_netdev_addr_lock_key, 1) and then
take (vlan_netdev_xmit_lock_key, 1)
- in the second case, we have (vlan_netdev_xmit_lock_key, 1) and then
take (macvlan_netdev_addr_lock_key, 1)
By removing the linktype check in dev_get_nest_level() and always
incrementing the nesting depth, lockdep considers this configuration
valid.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, trying to setup a vlan over a macsec device, or other
combinations of devices, triggers a lockdep warning.
Use netdev_lockdep_set_classes and ndo_get_lock_subclass, similar to
what macvlan does.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the missing of_node_put() after finishing the usage
of of_parse_phandle() or of_node_get() used by fixed_phy.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To fix runtime warning with lockdep is enabled due that u64_stats_sync
is not initialized well, so add it.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull block fixes from Jens Axboe:
- an NVMe fix from Gabriel, fixing a suspend/resume issue on some
setups
- addition of a few missing entries in the block queue sysfs
documentation, from Joe
- a fix for a sparse shadow warning for the bvec iterator, from
Johannes
- a writeback deadlock involving raid issuing barriers, and not
flushing the plug when we wakeup the flusher threads. From
Konstantin
- a set of patches for the NVMe target/loop/rdma code, from Roland and
Sagi
* 'for-linus' of git://git.kernel.dk/linux-block:
bvec: avoid variable shadowing warning
doc: update block/queue-sysfs.txt entries
nvme: Suspend all queues before deletion
mm, writeback: flush plugged IO in wakeup_flusher_threads()
nvme-rdma: Remove unused includes
nvme-rdma: start async event handler after reconnecting to a controller
nvmet: Fix controller serial number inconsistency
nvmet-rdma: Don't use the inline buffer in order to avoid allocation for small reads
nvmet-rdma: Correctly handle RDMA device hot removal
nvme-rdma: Make sure to shutdown the controller if we can
nvme-loop: Remove duplicate call to nvme_remove_namespaces
nvme-rdma: Free the I/O tags when we delete the controller
nvme-rdma: Remove duplicate call to nvme_remove_namespaces
nvme-rdma: Fix device removal handling
nvme-rdma: Queue ns scanning after a sucessful reconnection
nvme-rdma: Don't leak uninitialized memory in connect request private data
|
|
When CONFIG_NET_DSA_HWMON is disabled, we get warnings about two unused
functions whose only callers are all inside of an #ifdef:
drivers/net/dsa/mv88e6xxx.c:3257:12: 'mv88e6xxx_mdio_page_write' defined but not used [-Werror=unused-function]
drivers/net/dsa/mv88e6xxx.c:3244:12: 'mv88e6xxx_mdio_page_read' defined but not used [-Werror=unused-function]
This adds another ifdef around the function definitions. The warnings
appeared after the functions were marked 'static', but the problem
was already there before that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 57d3231057e9 ("net: dsa: mv88e6xxx: fix style issues")
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull VFIO fix from Alex Williamson:
"Fix oops when dereferencing empty data (Alex Williamson)"
* tag 'vfio-v4.8-rc2' of git://github.com/awilliam/linux-vfio:
vfio/pci: Fix NULL pointer oops in error interrupt setup handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"Two hibernation fixes allowing it to work with the recently added
randomization of the kernel identity mapping base on x86-64 and one
cpufreq driver regression fix.
Specifics:
- Fix the x86 identity mapping creation helpers to avoid the
assumption that the base address of the mapping will always be
aligned at the PGD level, as it may be aligned at the PUD level if
address space randomization is enabled (Rafael Wysocki).
- Fix the hibernation core to avoid executing tracing functions
before restoring the processor state completely during resume
(Thomas Garnier).
- Fix a recently introduced regression in the powernv cpufreq driver
that causes it to crash due to an out-of-bounds array access
(Akshay Adiga)"
* tag 'pm-4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / hibernate: Restore processor state before using per-CPU variables
x86/power/64: Always create temporary identity mapping correctly
cpufreq: powernv: Fix crash in gpstate_timer_handler()
|
|
|
|
Currently we free the resources backing the enclosure device before we
call device_unregister(). This is racy: during rmmod of low-level SCSI
drivers that hook into enclosure, we end up with a small window of time
during which writing to /sys can OOPS. Example trace with mpt3sas:
general protection fault: 0000 [#1] SMP KASAN
Modules linked in: mpt3sas(-) <...>
RIP: [<ffffffffa0388a98>] ses_get_page2_descriptor.isra.6+0x38/0x220 [ses]
Call Trace:
[<ffffffffa0389d14>] ses_set_fault+0xf4/0x400 [ses]
[<ffffffffa0361069>] set_component_fault+0xa9/0xf0 [enclosure]
[<ffffffff8205bffc>] dev_attr_store+0x3c/0x70
[<ffffffff81677df5>] sysfs_kf_write+0x115/0x180
[<ffffffff81675725>] kernfs_fop_write+0x275/0x3a0
[<ffffffff8151f810>] __vfs_write+0xe0/0x3e0
[<ffffffff8152281f>] vfs_write+0x13f/0x4a0
[<ffffffff81526731>] SyS_write+0x111/0x230
[<ffffffff828b401b>] entry_SYSCALL_64_fastpath+0x13/0x94
Fortunately the solution is extremely simple: call device_unregister()
before we free the resources, and the race no longer exists. The driver
core holds a reference over ->remove_dev(), so AFAICT this is safe.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Reviewed-by: James Bottomley <jejb@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Ingo Molnar:
"Misc fixes: a /dev/rtc regression fix, two APIC timer period
calibration fixes, an ARM clocksource driver fix and a NOHZ
power use regression fix"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/hpet: Fix /dev/rtc breakage caused by RTC cleanup
x86/timers/apic: Inform TSC deadline clockevent device about recalibration
x86/timers/apic: Fix imprecise timer interrupts by eliminating TSC clockevents frequency roundoff error
timers: Fix get_next_timer_interrupt() computation
clocksource/arm_arch_timer: Force per-CPU interrupt to be level-triggered
|
|
* pm-sleep:
PM / hibernate: Restore processor state before using per-CPU variables
x86/power/64: Always create temporary identity mapping correctly
* pm-cpufreq:
cpufreq: powernv: Fix crash in gpstate_timer_handler()
|
|
Free memory mapping, if probe is not successful.
Fixes: 4a9b37371822 ("power: reset: move hisilicon reboot code")
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
commit 4fcd504edbf7 ("power: reset: add reboot mode driver") uses api from
syscon, and syscon uses ioremap/iounmap which depends on HAS_IOMEM, so
let's depend on MFD_SYSCON instead of selecting it directly to avoid the
um-allyesconfig like build error on archs that without iomem:
drivers/mfd/syscon.c: In function 'of_syscon_register':
drivers/mfd/syscon.c:67:9: error: implicit declaration of function 'ioremap' [-Werror=implicit-function-declaration]
base = ioremap(res.start, resource_size(&res));
^
drivers/mfd/syscon.c:67:7: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
base = ioremap(res.start, resource_size(&res));
^
drivers/mfd/syscon.c:109:2: error: implicit declaration of function 'iounmap' [-Werror=implicit-function-declaration]
iounmap(base);
^
Reported-by: Kbuild test robot <fengguang.wu@intel.com>
Fixes: 4fcd504edbf7("power: reset: add reboot mode driver")
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
The device's model download function returns the model data as
an array of u32s, which is later compared to the reference
model data. However, since the latter is an array of u16s,
the comparison does not happen correctly, and model verification
fails. This in turn breaks the POR initialization sequence.
Fixes: 39e7213edc4f3 ("max17042_battery: Support regmap to access device's registers")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sven Van Asbroeck <TheSven73@googlemail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
mpt3sas crashes on resume after suspend with WarpDrive flash cards. The
reply_post_host_index array is not set back up after the resume, and we
deference a stale pointer in _base_interrupt().
[ 47.309711] BUG: unable to handle kernel paging request at ffffc90001f8006c
[ 47.318289] IP: [<ffffffffc00863ef>] _base_interrupt+0x49f/0xa30 [mpt3sas]
[ 47.326749] PGD 41ccaa067 PUD 41ccab067 PMD 3466c067 PTE 0
[ 47.333848] Oops: 0002 [#1] SMP
...
[ 47.452708] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.7.0 #6
[ 47.460506] Hardware name: Dell Inc. OptiPlex 990/06D7TR, BIOS A18 09/24/2013
[ 47.469629] task: ffffffff81c0d500 ti: ffffffff81c00000 task.ti: ffffffff81c00000
[ 47.479112] RIP: 0010:[<ffffffffc00863ef>] [<ffffffffc00863ef>] _base_interrupt+0x49f/0xa30 [mpt3sas]
[ 47.490466] RSP: 0018:ffff88041d203e30 EFLAGS: 00010002
[ 47.497801] RAX: 0000000000000001 RBX: ffff880033f4c000 RCX: 0000000000000001
[ 47.506973] RDX: ffffc90001f8006c RSI: 0000000000000082 RDI: 0000000000000082
[ 47.516141] RBP: ffff88041d203eb0 R08: ffff8804118e2820 R09: 0000000000000001
[ 47.525300] R10: 0000000000000001 R11: 00000000100c0000 R12: 0000000000000000
[ 47.534457] R13: ffff880412c487e0 R14: ffff88041a8987d8 R15: 0000000000000001
[ 47.543632] FS: 0000000000000000(0000) GS:ffff88041d200000(0000) knlGS:0000000000000000
[ 47.553796] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 47.561632] CR2: ffffc90001f8006c CR3: 0000000001c06000 CR4: 00000000000406f0
[ 47.570883] Stack:
[ 47.575015] 000000001d211228 ffff88041d2100c0 ffff8800c47d8130 0000000000000100
[ 47.584625] ffff8804100c0000 100c000000000000 ffff88041a8992a0 ffff88041a8987f8
[ 47.594230] ffff88041d203e00 ffffffff81111e55 000000000000038c ffff880414ad4280
[ 47.603862] Call Trace:
[ 47.608474] <IRQ>
[ 47.610413] [<ffffffff81111e55>] ? call_timer_fn+0x35/0x120
[ 47.620539] [<ffffffff81100a1f>] handle_irq_event_percpu+0x7f/0x1c0
[ 47.629061] [<ffffffff81100b8c>] handle_irq_event+0x2c/0x50
[ 47.636859] [<ffffffff81103fff>] handle_edge_irq+0x6f/0x130
[ 47.644654] [<ffffffff8102fbf3>] handle_irq+0x73/0x120
[ 47.652011] [<ffffffff810c6ada>] ? atomic_notifier_call_chain+0x1a/0x20
[ 47.660854] [<ffffffff817e374b>] do_IRQ+0x4b/0xd0
[ 47.667777] [<ffffffff817e160c>] common_interrupt+0x8c/0x8c
[ 47.675635] <EOI>
Move the reply_post_host_index array setup into
mpt3sas_base_map_resources(), which is also in the resume path.
Cc: stable@vger.kernel.org
Signed-off-by: Greg Edwards <gedwards@fireweed.org>
Acked-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
