| Age | Commit message (Collapse) | Author |
|---|
|
The report descriptor for the HOLTEK USB ID 04d9:a0c2 (ETEKCITY Scroll
T-140 Gaming Mouse) is set to a very large amount of consumer usages
(2^16), exceeding HID_MAX_USAGES. Added id, bindings and comments for
the mouse, added to hid_have_special_driver, and reduced the usage and
logical maximums to 0x2fff, consistent with the other mice in the
category. Tested on the hardware.
Signed-off-by: John C. DeSilva <desilvjo@umich.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Hans Petter Selasky <hps@selasky.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch adds a seperate hid-penmount driver to work
around an issue with the HID report descriptor. The
descriptor does not contain the ContactID usage and as
result the touchscreen is represented as normal mouse
to the system.
This driver maps the button 0 emitted by the touchscreen
to BTN_TOUCH. This makes it possible to use touch events
in userspace.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
thingm_remove_rgb() needs to flush the workqueue after all the LED classes
have been unregistered, otherwise the removal might race with another LED
event coming, causing thingm_led_set() to schedule additional work after
thingm_remove_rgb() has flushed it. This obviously causes oops later, as
the scheduled work has been freed in the meantime.
In addition to that, move the hid_hw_stop() to an earlier place, so that
dmesg is not polluted by failure messages about not being able to write
the LED while the device is being shut down.
Reported-and-tested-by: Dylan Alex Simon <dylan-kernel@dylex.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch changes the way usbhid carries out Clear-Halt and reset.
Currently, after a Clear-Halt on the interrupt-IN endpoint, the driver
immediately restarts the interrupt URB, even if the Clear-Halt failed.
This doesn't work out well when the reason for the failure was that
the device was disconnected (when a low- or full-speed device is
connected through a hub to an EHCI controller, transfer errors caused
by disconnection are reported as stalls by the hub). Instead now the
driver will attempt a reset after a failed Clear-Halt.
The way resets are carried out is also changed. Now the driver will
call usb_queue_reset_device() instead of calling usb_reset_device()
directly. This avoids a deadlock that would arise when a device is
unplugged: The hid_reset() routine runs as a workqueue item, a reset
attempt after the device has been unplugged will fail, failure will
cause usbhid to be unbound, and the disconnect routine will try to do
cancel_work_sync(). The usb_queue_reset_device() implementation is
carefully written to handle scenarios like this one properly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Atmel 840B digitizer presents a stylus interface which reports twice
the X coordinate and then twice the Y coordinate. In its current
implementation, hid-input assign the first X to X, then the second to Y,
then the first Y to Z, then the second one to RX.
This is wrong, and X should always be mapped to X, no matter what.
A solution consists in forcing X, Y, Z, RX, RY, RZ to be mapped to their
correct user space counter part.
Reported-by: Éric Brunet <Eric.Brunet@lps.ens.fr>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- fixes for a couple potential memory corruption problems (the HW would
have to be manufactured to be deliberately evil to trigger those)
found by Ben Hawkes
- fix for potential infinite loop when using sysfs interface of
logitech driver, from Simon Wood
- a couple more simple driver fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: fix a couple of off-by-ones
HID: logitech: perform bounds checking on device_id early enough
HID: logitech: fix bounds checking on LED report size
HID: logitech: Prevent possibility of infinite loop when using /sys interface
HID: rmi: print an error if F11 is not found instead of stopping the device
HID: hid-sensor-hub: use devm_ functions consistently
HID: huion: Use allocated buffer for DMA
HID: huion: Fail on parameter retrieval errors
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Here is the fixup for the 'lowlight' of my last pull request. I2C is
not selected anymore by I2C_ACPI. Instead, the code in question now
depends on I2C=y.
Also, Mika has agreed to support me and be the maintainer for I2C-ACPI
related patches. Finally, a new-ID-patch came along last week"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: add maintainer for ACPI parts of I2C
i2c: i801: Add PCI ID for Intel Braswell
i2c: rework kernel config I2C_ACPI
|
|
There are a few very theoretical off-by-one bugs in report descriptor size
checking when performing a pre-parsing fixup. Fix those.
Cc: stable@vger.kernel.org
Reported-by: Ben Hawkes <hawkes@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
device_index is a char type and the size of paired_dj_deivces is 7
elements, therefore proper bounds checking has to be applied to
device_index before it is used.
We are currently performing the bounds checking in
logi_dj_recv_add_djhid_device(), which is too late, as malicious device
could send REPORT_TYPE_NOTIF_DEVICE_UNPAIRED early enough and trigger the
problem in one of the report forwarding functions called from
logi_dj_raw_event().
Fix this by performing the check at the earliest possible ocasion in
logi_dj_raw_event().
Cc: stable@vger.kernel.org
Reported-by: Ben Hawkes <hawkes@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The check on report size for REPORT_TYPE_LEDS in logi_dj_ll_raw_request()
is wrong; the current check doesn't make any sense -- the report allocated
by HID core in hid_hw_raw_request() can be much larger than
DJREPORT_SHORT_LENGTH, and currently logi_dj_ll_raw_request() doesn't
handle this properly at all.
Fix the check by actually trimming down the report size properly if it is
too large.
Cc: stable@vger.kernel.org
Reported-by: Ben Hawkes <hawkes@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Pull x86 platform driver revert from Matthew Garrett:
"This clearly shouldn't have been merged. No excuse on my part"
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
Revert "platform/x86/toshiba-apci.c possible bad if test?"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"These are the two bug fixes I mentioned in the final merge window
pull. One is a reversed logic check in the device busy tests which
can cause a nasty hang and another crash seen in the new SCSI pool
support if the use count ever goes to zero"
[ The device busy test already got merged from a patch earlier, so is
now duplicated. ]
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] save command pool address of Scsi_Host
[SCSI] fix qemu boot hang problem
|
|
This reverts commit bdc3ae7221213963f438faeaa69c8b4a2195f491.
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
|
|
The latest kernel fails to boot qemu arm images when using scsi
for disk access. Boot gets stuck after the following messages.
brd: module loaded
sym53c8xx 0000:00:0c.0: enabling device (0100 -> 0103)
sym0: <895a> rev 0x0 at pci 0000:00:0c.0 irq 93
sym0: No NVRAM, ID 7, Fast-40, LVD, parity checking
sym0: SCSI BUS has been reset.
scsi host0: sym-2.2.3
Bisect points to commit 71e75c97f97a ("scsi: convert device_busy to
atomic_t"). Code inspection shows the following suspicious change
in scsi_request_fn.
out_delay:
- if (sdev->device_busy == 0 && !scsi_device_blocked(sdev))
+ if (atomic_read(&sdev->device_busy) && !scsi_device_blocked(sdev))
blk_delay_queue(q, SCSI_QUEUE_DELAY);
}
'sdev->device_busy == 0' was replaced with 'atomic_read(&sdev->device_busy)',
meaning the logic was reversed. Changing this expression to
'!atomic_read(&sdev->device_busy)' fixes the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
Reviewed-by: Webb Scales <webbnh@hp.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The SMBus host controller is the same as used in Baytrail so add the new
PCI ID to the driver's list of supported IDs.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Commit da3c6647(I2C/ACPI: Clean up I2C ACPI code and Add CONFIG_I2C_ACPI
config) adds a new kernel config I2C_ACPI and make I2C core built in
when the config is selected. This is wrong because distributions
etc generally compile I2C as a module and the commit broken that.
This patch is to rename I2C_ACPI to ACPI_I2C_OPREGION. New config
only controls ACPI I2C operation region code and depends on I2C=y.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[wsa: removed unrelated change for Kconfig]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Pull md bugfixes from Neil Brown:
"Here are the bug-fixes I promised :-)
Funny how you start looking for one and other start appearing.
- raid6 data corruption during recovery
- raid6 livelock
- raid10 memory leaks"
* tag 'md/3.17-fixes' of git://neil.brown.name/md:
md/raid10: always initialise ->state on newly allocated r10_bio
md/raid10: avoid memory leak on error path during reshape.
md/raid10: Fix memory leak when raid10 reshape completes.
md/raid10: fix memory leak when reshaping a RAID10.
md/raid6: avoid data corruption during recovery of double-degraded RAID6
md/raid5: avoid livelock caused by non-aligned writes.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Marvell MVEBU
- Remove ARCH_KIRKWOOD dependency (Andrew Lunn)
NVIDIA Tegra
- Add debugfs support (Thierry Reding)
Synopsys DesignWare
- Look for configuration space in 'reg', not 'ranges' (Kishon Vijay Abraham I)
- Program ATU with untranslated address (Kishon Vijay Abraham I)
- Add config access-related pcie_host_ops for v3.65 hardware (Murali Karicheri)
- Add MSI-related pcie_host_ops for v3.65 hardware (Murali Karicheri)
TI DRA7xx
- Add TI DR7xx PCIe driver (Kishon Vijay Abraham I)"
* tag 'pci-v3.17-changes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: designware: Add MSI-related pcie_host_ops for v3.65 hardware
PCI: designware: Add config access-related pcie_host_ops for v3.65 hardware
PCI: dra7xx: Add TI DRA7xx PCIe driver
PCI: designware: Program ATU with untranslated address
PCI: designware: Look for configuration space in 'reg', not 'ranges'
PCI: tegra: Add debugfs support
PCI: mvebu: Remove ARCH_KIRKWOOD dependency
|
|
Pull devicetree fixes from Grant Likely:
"Three more commits needed for v3.17: A bug fix for reserved regions
based at address zero, a clarification on how to interpret existence
of both interrupts and interrupts-extended properties, and a fix to
allow device tree testcases to run on any platform"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
of/irq: Fix lookup to use 'interrupts-extended' property first
Enabling OF selftest to run without machine's devicetree
of: Allow mem_reserve of memory with a base address of zero
|
|
Most places which allocate an r10_bio zero the ->state, some don't.
As the r10_bio comes from a mempool, and the allocation function uses
kzalloc it is often zero anyway. But sometimes it isn't and it is
best to be safe.
I only noticed this because of the bug fixed by an earlier patch
where the r10_bios allocated for a reshape were left around to
be used by a subsequent resync. In that case the R10BIO_IsReshape
flag caused problems.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
If raid10 reshape fails to find somewhere to read a block
from, it returns without freeing memory...
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
When a raid10 commences a resync/recovery/reshape it allocates
some buffer space.
When a resync/recovery completes the buffer space is freed. But not
when the reshape completes.
This can result in a small memory leak.
There is a subtle side-effect of this bug. When a RAID10 is reshaped
to a larger array (more devices), the reshape is immediately followed
by a "resync" of the new space. This "resync" will use the buffer
space which was allocated for "reshape". This can cause problems
including a "BUG" in the SCSI layer. So this is suitable for -stable.
Cc: stable@vger.kernel.org (v3.5+)
Fixes: 3ea7daa5d7fde47cd41f4d56c2deb949114da9d6
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
raid10 reshape clears unwanted bits from a bio->bi_flags using
a method which, while clumsy, worked until 3.10 when BIO_OWNS_VEC
was added.
Since then it clears that bit but shouldn't. This results in a
memory leak.
So change to used the approved method of clearing unwanted bits.
As this causes a memory leak which can consume all of memory
the fix is suitable for -stable.
Fixes: a38352e0ac02dbbd4fa464dc22d1352b5fbd06fd
Cc: stable@vger.kernel.org (v3.10+)
Reported-by: mdraid.pkoch@dfgh.net (Peter Koch)
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
During recovery of a double-degraded RAID6 it is possible for
some blocks not to be recovered properly, leading to corruption.
If a write happens to one block in a stripe that would be written to a
missing device, and at the same time that stripe is recovering data
to the other missing device, then that recovered data may not be written.
This patch skips, in the double-degraded case, an optimisation that is
only safe for single-degraded arrays.
Bug was introduced in 2.6.32 and fix is suitable for any kernel since
then. In an older kernel with separate handle_stripe5() and
handle_stripe6() functions the patch must change handle_stripe6().
Cc: stable@vger.kernel.org (2.6.32+)
Fixes: 6c0069c0ae9659e3a91b68eaed06a5c6c37f45c8
Cc: Yuri Tikhonov <yur@emcraft.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Reported-by: "Manibalan P" <pmanibalan@amiindia.co.in>
Tested-by: "Manibalan P" <pmanibalan@amiindia.co.in>
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1090423
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
|
|
If a stripe in a raid6 array received a write to each data block while
the array is degraded, and if any of these writes to a missing device
are not page-aligned, then a live-lock happens.
In this case the P and Q blocks need to be read so that the part of
the missing block which is *not* being updated by the write can be
constructed. Due to a logic error, these blocks are not loaded, so
the update cannot proceed and the stripe is 'handled' repeatedly in an
infinite loop.
This bug is unlikely as most writes are page aligned. However as it
can lead to a livelock it is suitable for -stable. It was introduced
in 3.16.
Cc: stable@vger.kernel.org (v3.16)
Fixed: 67f455486d2ea20b2d94d6adf5b9b783d079e321
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Pull x86 platform driver updates from Matthew Garrett:
"A moderate number of changes, but nothing awfully significant.
A lot of const cleanups, some reworking and additions to the rfkill
quirks in the asus driver, a new driver for generating falling laptop
events on Toshibas and some misc fixes.
Maybe vendors have stopped inventing things"
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86: (41 commits)
platform/x86: Enable build support for toshiba_haps
Documentation: Add file about toshiba_haps module
platform/x86: Toshiba HDD Active Protection Sensor
asus-nb-wmi: Add wapf4 quirk for the U32U
alienware-wmi: make hdmi_mux enabled on case-by-case basis
ideapad-laptop: Constify DMI table and other r/o variables
asus-nb-wmi.c: Rename x401u quirk to wapf4
compal-laptop: correct invalid hwmon name
toshiba_acpi: Add Qosmio X75-A to the alt keymap dmi list
toshiba_acpi: Add extra check to backlight code
Fix log message about future removal of interface
ideapad-laptop: Disable touchpad interface on Yoga models
asus-nb-wmi: Add wapf4 quirk for the X550CC
intel_ips: Make ips_mcp_limits variables static
thinkpad_acpi: Mark volume_alsa_control_{vol,mute} as __initdata
fujitsu-laptop: Mark fujitsu_dmi_table[] DMI table as __initconst
hp-wmi: Add missing __init annotations to initialization code
hp_accel: Constify ACPI and DMI tables
fujitsu-tablet: Mark DMI callbacks as __init code
dell-laptop: Mark dell_quirks[] DMI table as __initconst
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull idle update from Len Brown:
"Two Intel-platform-specific updates to intel_idle, and a cosmetic
tweak to the turbostat utility"
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: tweak whitespace in output format
intel_idle: Broadwell support
intel_idle: Disable Baytrail Core and Module C6 auto-demotion
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/amit/virtio
Pull virtio-rng update from Amit Shah:
"Add derating factor for use by hwrng core
Sending directly to you with the commit log changes Ted Ts'o pointed
out. Not sure if Rusty's back after his travel, but this already has
his s-o-b"
* 'rng-queue' of git://git.kernel.org/pub/scm/linux/kernel/git/amit/virtio:
virtio: rng: add derating factor for use by hwrng core
|
|
Makefile and Kconfig build support patch for the newly introduced
kernel module toshiba_haps.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
|
|
This driver adds support for the built-in accelereometer found
on recent Toshiba laptops with HID TOS620A.
This driver receives ACPI notify events 0x80 when the sensor
detects a sudden move or a harsh vibration, as well as an
ACPI notify event 0x81 whenever the movement or vibration has
been stabilized.
Also provides sysfs entries to get/set the desired protection
level and reseting the HDD protection interface.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
|
|
As reported here: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1173681
the U32U needs wapf=4 too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
|
|
Not all HW supporting WMAX method will support the HDMI mux feature.
Explicitly quirk the HW that does support it.
Signed-off-by: Mario Limonciello <mario_limonciello@dell.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
|
|
Constify the rfkill_blacklist[] DMI table, the ideapad_rfk_data[] table
and the ideapad_attribute_group attribute group. There's no need to have
them writeable during runtime.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Ike Panhc <ike.pan@canonical.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
|
|
The actual x401u does not use the so named x401u quirk but the x55u quirk.
All that the x401u quirk does it setting wapf to 4, so rename it to wapf4 to
stop the confusion.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
|
|
Change the name of the hwmon interface from "compal-laptop" to "compal".
A dash is an invalid character for a hwmon name and caused the call to
hwmon_device_register_with_groups() to fail.
Signed-off-by: Roald Frederickx <roald.frederickx@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
|
|
The Toshiba Qosmio X75-A series models also come with
the new keymap layout.
This patch adds this model to the alt_keymap_dmi list,
along with an extra key found on these models.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
|
|
Some Toshiba models (most notably Qosmios) come with an
incomplete backlight method where the AML code doesn't
check for write or read commands and always returns
HCI_SUCCESS and the actual brightness (and in some
cases the max brightness), thus allowing the backlight
interface to be registered without write support.
This patch changes the set_lcd_brightness function,
checking the returned values for values greater than
zero to avoid registering a broken backlight interface.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
|
|
If this is going away, it won't be in 2012.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
|
|
Yoga models don't offer touchpad ctrl through the ideapad interface, causing
ideapad_sync_touchpad_state to send wrong touchpad enable/disable events.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
|
|
As reported here: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1173681
the X550CC needs wapf=4 too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
|
|
These variables don't need to be visible outside of this compilation
unit, make them static.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
|
|
Mark volume_alsa_control_vol and volume_alsa_control_mute as __initdata,
as snd_ctl_new1() will copy the relevant parts, so there is no need to
keep the master copies around after initialization.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Henrique de Moraes Holschuh <ibm-acpi@hmh.eng.br>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
|
|
The DMI table is only ever used during initialization. Mark it as
__initconst so its memory can be released afterwards -- roughly 1.5 kB.
In turn, the callback functions can be marked with __init, too.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
|
|
These functions are only called from other initialization routines, so
can be marked __init, too.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
|
|
Constify the lis3lv02d_device_ids[] ACPI and the lis3lv02d_dmi_ids[] DMI
tables. There's no need to have them writeable during runtime.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
|
|
The DMI table is already marked as __initconst, so can be the callback
functions as they're only used in that context.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Robert Gerlach <khnz@gmx.de>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
|
|
The dell_quirks[] DMI table is only ever used during initialization.
Mark it as __initconst so its memory can be released afterwards --
roughly 5.7 kB. In turn, the callback function can be marked with
__init, too.
Also the touchpad_led_init() function can be marked __init as it's only
referenced from dell_init() -- an __init function.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
|
|
Constify the asus_quirks[] DMI table. There's no need to have it
writeable during runtime.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
|
|
Quite a lot of code and data of acer-wmi.c is only ever used during
initialization. Mark those accordingly -- and constify, where
appropriate -- so the memory can be released afterwards.
All in all those changes move ~10 kB of code and data to the .init
sections, marking them for release after initialization has finished.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: "Lee, Chun-Yi" <jlee@suse.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
|
