| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull the second batch of irqchip updates for 4.15 from marc Zyngier:
- A number of MIPS GIC updates and cleanups
- One GICv4 update
- Another firmware workaround for GICv2
- Support for Mason8 GPIOs
- Tiny documentation fix
|
|
We have 2 bitmaps used to keep track of interrupts dedicated to IPIs in
the MIPS GIC irqchip driver. These bitmaps are only used from the one
compilation unit of that driver, and so can be made static. Do so in
order to avoid polluting the symbol table & global namespace.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The gic_set_type() function included writes to the MIPS GIC polarity,
trigger & dual-trigger registers in each case of a switch statement
determining the IRQs type. This is all well & good when we only have a
single cluster & thus a single GIC whose register we want to update. It
will lead to significant duplication once we have multi-cluster support
& multiple GICs to update.
Refactor this such that we determine values for the polarity, trigger &
dual-trigger registers and then have a single set of register writes
following the switch statement. This will allow us to write the same
values to each GIC in a multi-cluster system in a later patch, rather
than needing to duplicate more register writes in each case.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Following the past few patches nothing uses the gic_vpes variable any
longer. Remove the dead code.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Reserving a number of IPIs based upon the number of VPs reported by the
GIC makes little sense for a few reasons:
- The kernel may have been configured with NR_CPUS less than the number
of VPs in the cluster, in which case using gic_vpes causes us to
reserve more interrupts for IPIs than we will possibly use.
- If a kernel is configured without support for multi-threading & runs
on a system with multi-threading & multiple VPs per core then we'll
similarly reserve more interrupts for IPIs than we will possibly use.
- In systems with multiple clusters the GIC can only provide us with
the number of VPs in its cluster, not across all clusters. In this
case we'll reserve fewer interrupts for IPIs than we need.
Fix these issues by using num_possible_cpus() instead, which in all
cases is actually indicative of how many IPIs we may need.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Rather than configuring EIC mode for all CPUs during boot, configure it
locally on each when they come online. This will become important with
multi-cluster support, since clusters may be powered on & off (for
example via hotplug) and would lose the EIC configuration when powered
off.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
We currently walk through the range 0..gic_vpes-1, expecting these
values all to be valid Linux CPU numbers to provide to mips_cm_vp_id(),
and masking all routable local interrupts during boot. This approach has
a few drawbacks:
- In multi-cluster systems we won't have access to all CPU's GIC local
registers when the driver is probed, since clusters (and their GICs)
may be powered down at this point & only brought online later.
- In multi-cluster systems we may power down clusters at runtime, for
example if we offline all CPUs within it via hotplug, and the
cluster's GIC may lose state. We therefore need to reinitialise it
when powering back up, which this approach does not take into
account.
- The range 0..gic_vpes-1 may not all be valid Linux CPU numbers, for
example if we run a kernel configured to support fewer CPUs than the
system it is running on actually has. In this case we'll get garbage
values from mips_cm_vp_id() as we read past the end of the cpu_data
array.
Fix this and simplify the code somewhat by writing an all-bits-set
value to the VP-local reset mask register when a CPU is brought online,
before any local interrupts are configured for it. This removes the need
for us to access all CPUs during driver probe, removing all of the
problems described above.
In the name of simplicity we drop the checks for routability of
interrupts and simply clear the mask bits for all interrupts. Bits for
non-routable local interrupts will have no effect so there's no point
performing extra work to avoid modifying them.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The gic_all_vpes_local_irq_controller chip currently attempts to operate
on all CPUs/VPs in the system when masking or unmasking an interrupt.
This has a few drawbacks:
- In multi-cluster systems we may not always have access to all CPUs in
the system. When all CPUs in a cluster are powered down that
cluster's GIC may also power down, in which case we cannot configure
its state.
- Relatedly, if we power down a cluster after having configured
interrupts for CPUs within it then the cluster's GIC may lose state &
we need to reconfigure it. The current approach doesn't take this
into account.
- It's wasteful if we run Linux on fewer VPs than are present in the
system. For example if we run a uniprocessor kernel on CPU0 of a
system with 16 CPUs then there's no point in us configuring CPUs
1-15.
- The implementation is also lacking in that it expects the range
0..gic_vpes-1 to represent valid Linux CPU numbers which may not
always be the case - for example if we run on a system with more VPs
than the kernel is configured to support.
Fix all of these issues by only configuring the affected interrupts for
CPUs which are online at the time, and recording the configuration in a
new struct gic_all_vpes_chip_data for later use by CPUs being brought
online. We register a CPU hotplug state (reusing
CPUHP_AP_IRQ_GIC_STARTING which the ARM GIC driver uses, and which seems
suitably generic for reuse with the MIPS GIC) and execute
irq_cpu_online() in order to configure the interrupts on the newly
onlined CPU.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The gic_local_irq_domain_map() function has only one callsite in
gic_irq_domain_map(), and the split between the two functions makes it
unclear that they duplicate calculations & checks.
Inline gic_local_irq_domain_map() into gic_irq_domain_map() in order to
clean this up. Doing this makes the following small issues obvious, and
the patch tidies them up:
- Both functions used GIC_HWIRQ_TO_LOCAL() to convert a hwirq number to
a local IRQ number. We now only do this once. Although the compiler
ought to have optimised this away before anyway, the change leaves us
with less duplicate code.
- gic_local_irq_domain_map() had a check for invalid local interrupt
numbers (intr > GIC_LOCAL_INT_FDC). This condition can never occur
because any hwirq higher than those used for local interrupts is a
shared interrupt, which gic_irq_domain_map() already handles
separately. We therefore remove this check.
- The decision of whether to map the interrupt to gic_cpu_pin or
timer_cpu_pin can be handled within the existing switch statement in
gic_irq_domain_map(), shortening the code a little.
The change additionally prepares us nicely for the following patch of
the series which would otherwise need to duplicate the check for whether
a local interrupt should be percpu_devid or just percpu (ie. the switch
statement from gic_irq_domain_map()) in gic_local_irq_domain_map().
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Meson8 uses the same GPIO interrupt controller IP block as the other
Meson SoCs. A total of 134 pins can be spied on, which is the sum of:
- 22 pins on bank GPIOX
- 17 pins on bank GPIOY
- 30 pins on bank GPIODV
- 10 pins on bank GPIOH
- 15 pins on bank GPIOZ
- 7 pins on bank CARD
- 19 pins on bank BOOT
- 14 pins in the AO domain
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
There is a lot of broken firmware out there that don't really
expose the information the kernel requires when it comes with dealing
with GICv2:
(1) Firmware that only describes the first 4kB of GICv2
(2) Firmware that describe 128kB of CPU interface, while
the usable portion of the address space is between
60 and 68kB
So far, we only deal with (2). But we have platforms exhibiting
behaviour (1), resulting in two sub-cases:
(a) The GIC is occupying 8kB, as required by the GICv2 architecture
(b) It is actually spread 128kB, and this is likely to be a version
of (2)
This patch tries to work around both (a) and (b) by poking at
the outside of the described memory region, and try to work out
what is actually there. This is of course unsafe, and should
only be enabled if there is no way to otherwise fix the DT provided
by the firmware (we provide a "irqchip.gicv2_force_probe" option
to that effect).
Note that for the time being, we restrict ourselves to GICv2
implementations provided by ARM, since there I have no knowledge
of an alternative implementations. This could be relaxed if such
an implementation comes to light on a broken platform.
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
So far, we require the hypervisor to update the VLPI properties
once the the VLPI mapping has been established. While this
makes it easy for the ITS driver, it creates a window where
an incoming interrupt can be delivered with an unknown set
of properties. Not very nice.
Instead, let's add a "properties" field to the mapping structure,
and use that to configure the VLPI before it actually gets mapped.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Required merge to get mainline irqchip updates.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The driver fails to compile with CONFIG_COMPILE_TEST=y on x86:
irq-meson-gpio.c: In function ‘meson_gpio_irq_parse_dt’:
irq-meson-gpio.c:343:8: error: implicit declaration of function
‘of_property_read_variable_u32_array’
ret = of_property_read_variable_u32_array(node,
Adding COMPILE_TEST to a driver requires at least compile testing it for
x86....
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
|
|
In case of error, the function of_iomap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test..
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Add support for the interrupt gpio controller found on Amlogic's meson
SoC family.
This controller is a separate controller from the gpio controller. It is
able to spy on the SoC pad. It is essentially a 256 to 8 router with a
filtering block to select level or edge and polarity. The number of actual
mappable inputs depends on the SoC.
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
When setting the affinity of a VPE (either because we map or move
it), make sure the effective affinity is correctly reported back
to the core kernel.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Sending VINVALL to all ITSs is completely pointless, as all
we're trying to achieve is to tell the redistributor that
the property table for this VPE should be invalidated.
Let's issue the command on the first valid ITS and be done with it.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
So far, we map all VPEs on all ITSs. While this is not wrong,
this is quite a big hammer, as moving a VPE around requires
all ITSs to be synchronized. Needles to say, this is an
expensive proposition.
Instead, let's switch to a mode where we issue VMAPP commands
only on ITSs that are actually involved in reporting interrupts
to the given VM.
For that purpose, we refcount the number of interrupts are are
mapped for this VM on each ITS, performing the map/unmap
operations as required. It then allows us to use this refcount
to only issue VMOVP to the ITSs that need to know about this
VM.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Currently, its_send_vmapp operates on all ITSs. As we're about
to try and limit the amount of commands we send to ITSs that are
not involved in dealing with a given VM, let's redefine that
primitive so that it takes a target ITS as a parameter.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Currently, its_send_vinvall operates on all ITSs. As we're about
to try and limit the amount of commands we send to ITSs that are
not involved in dealing with a given VM, let's redefine that
primitive so that it takes a target ITS as a parameter.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
As we're about to make use of the maximum number of ITSs in
a GICv4 system, let's make this value global (and rename it to
GICv4_ITS_LIST_MAX).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
At boot time, we enumerate all the GICv4-capable ITSs, and build
a mask of the available ITSs. Take this opportunity to store
the ITS number in the its_node structure so that we can use it
at a later time.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The ITSes on the Hip07 (as present in the Huawei D05) are broken when
it comes to addressing the redistributors, and need to be explicitely
told to address the VLPI page instead of the redistributor base address.
So let's add yet another quirk, fixing up the target address
in the command stream.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
In order to be able to issue command variants depending on
how broken an ITS is, let's pass the its pointer to all
command building primitives.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
If the ITS stops processing commands, we're pretty much toasted
as we cannot update the configuration anymore (and we're not
even sure that the ITS still translates interrups).
If that happens, let's dump some basic information about the
state of affairs before moving on.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The Socionext Synquacer SoC's implementation of GICv3 has a so-called
'pre-ITS', which maps 32-bit writes targeted at a separate window of
size '4 << device_id_bits' onto writes to GITS_TRANSLATER with device
ID taken from bits [device_id_bits + 1:2] of the window offset.
Writes that target GITS_TRANSLATER directly are reported as originating
from device ID #0.
So add a workaround for this. Given that this breaks isolation, clear
the IRQ_DOMAIN_FLAG_MSI_REMAP flag as well.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
As it turns out, the IIDR is not sufficient to distinguish between GICv3
implementations when it comes to enabling quirks. So update the prototype
of the init() hook to return a bool, and interpret a 'false' return value
as no match, in which case the 'enabling workaround' log message should
not be printed.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Before adding another SoC whose device ID space deviates from the
value presented in the GIC ID registers, let's slightly refactor
the code so that the ID registers are probed before that quirks
handling executes. This allows us to move the device ID override
into the quirk handler itself.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
A new feature Range Selector (RS) has been added to GIC specification
in order to support more than 16 CPUs at affinity level 0. New fields
are introduced in SGI system registers (ICC_SGI0R_EL1, ICC_SGI1R_EL1
and ICC_ASGI1R_EL1) to relax an artificial limit of 16 at level 0.
- A new RSS field in ICC_CTLR_EL3, ICC_CTLR_EL1 and ICV_CTLR_EL1:
[18] - Range Selector Support (RSS)
0b0 = Targeted SGIs with affinity level 0 values of 0-15 are supported.
0b1 = Targeted SGIs with affinity level 0 values of 0-255 are supported.
- A new RS field in ICC_SGI0R_EL1, ICC_SGI1R_EL1 and ICC_ASGI1R_EL1:
[47:44] - RangeSelector (RS) which group of 16 TargetList[n] field
TargetList[n] represents aff0 value ((RS*16)+n)
When ICC_CTLR_EL3.RSS==0 or ICC_CTLR_EL1.RSS==0, RS is RES0.
- A new RSS field in GICD_TYPER:
[26] - Range Selector Support (RSS)
0b0 = Targeted SGIs with affinity level 0 values of 0-15 are supported.
0b1 = Targeted SGIs with affinity level 0 values of 0-255 are supported.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Add the initialization of the generic irq chip for the BCM7271 L2
interrupt controller. This controller only supports level
interrupts and uses the "brcm,bcm7271-l2-intc" compatibility
string.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Added register block offsets to the brcmstb_l2_intc_data structure
for the status and mask registers to support reading the active
interupts in an abstracted way. It seems like an irq_chip method
should have been provided for this, but it's not there yet.
Abstracted the implementation of the handler, suspend, and resume
functions to not use any hard coded register offsets.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Saving the generic chip pointer in the brcmstb_l2_intc_data prevents
the need to call irq_get_domain_generic_chip(). Also don't need to
save parent_irq and base there since local variables in the
brcmstb_l2_intc_of_init() function are just as good.
The handle_edge_irq flow or chained_irq_enter takes care of the
acknowledgment of the interrupt so it is redundant to clear it in
brcmstb_l2_intc_irq_handle().
irq_linear_revmap() is a fast path equivalent of irq_find_mapping()
that is appropriate to use for domain controllers of this type.
Defining irq_mask_ack is slightly more efficient than just
implementing irq_mask and irq_ack separately.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Use the of_device_get_match_data() helper instead of open coding.
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Add a menu for IRQ chip drivers. This makes the Device drivers menu be more
consistent (listing "subsystems" instead of specific options) and makes the
IRQCHIP options be listed in expected places for 'make menu|xconfig'.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: https://lkml.kernel.org/r/3db7385a-c6a1-5c93-0797-6f4b6b2b2cde@infradead.org
|
|
omap_nr_pending and omap_nr_irqs variables are initialized
right at the beginning of intc_of_init function, so there's
no need to statically initialize them.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: https://lkml.kernel.org/r/20171016161303.veumgcd3xom5c54r@lenoch
|
|
All mach-omap2 variants are device tree only now, so this function is dead
code. Remove it.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-omap@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: https://lkml.kernel.org/r/20171016160422.uu2i7vvrgy7cc4aw@lenoch
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"This contains the following fixes and improvements:
- Avoid dereferencing an unprotected VMA pointer in the fault signal
generation code
- Fix inline asm call constraints for GCC 4.4
- Use existing register variable to retrieve the stack pointer
instead of forcing the compiler to create another indirect access
which results in excessive extra 'mov %rsp, %<dst>' instructions
- Disable branch profiling for the memory encryption code to prevent
an early boot crash
- Fix a sparse warning caused by casting the __user annotation in
__get_user_asm_u64() away
- Fix an off by one error in the loop termination of the error patch
in the x86 sysfs init code
- Add missing CPU IDs to various Intel specific drivers to enable the
functionality on recent hardware
- More (init) constification in the numachip code"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm: Use register variable to get stack pointer value
x86/mm: Disable branch profiling in mem_encrypt.c
x86/asm: Fix inline asm call constraints for GCC 4.4
perf/x86/intel/uncore: Correct num_boxes for IIO and IRP
perf/x86/intel/rapl: Add missing CPU IDs
perf/x86/msr: Add missing CPU IDs
perf/x86/intel/cstate: Add missing CPU IDs
x86: Don't cast away the __user in __get_user_asm_u64()
x86/sysfs: Fix off-by-one error in loop termination
x86/mm: Fix fault error path using unsafe vma pointer
x86/numachip: Add const and __initconst to numachip2_clockevent
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
- Add a missing NULL pointer check in free_irq()
- Fix a memory leak/memory corruption in the generic irq chip
- Add missing rcu annotations for radix tree access
- Use ffs instead of fls when extracting data from a chip register in
the MIPS GIC irq driver
- Fix the unmasking of IPI interrupts in the MIPS GIC driver so they
end up at the target CPU and not at CPU0
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irq/generic-chip: Don't replace domain's name
irqdomain: Add __rcu annotations to radix tree accessors
irqchip/mips-gic: Use effective affinity to unmask
irqchip/mips-gic: Fix shifts to extract register fields
genirq: Check __free_irq() return value for NULL
|
|
Pull mtd fixes from Boris Brezillon:
- Fix partition alignment check in mtdcore.c
- Fix a buffer overflow in the Atmel NAND driver
* tag 'mtd/fixes-for-4.14-rc3' of git://git.infradead.org/linux-mtd:
mtd: nand: atmel: fix buffer overflow in atmel_pmecc_user
mtd: Fix partition alignment check on multi-erasesize devices
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Eight mostly minor fixes for recently discovered issues in drivers"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ILLEGAL REQUEST + ASC==27 => target failure
scsi: aacraid: Add a small delay after IOP reset
scsi: scsi_transport_fc: Also check for NOTPRESENT in fc_remote_port_add()
scsi: scsi_transport_fc: set scsi_target_id upon rescan
scsi: scsi_transport_iscsi: fix the issue that iscsi_if_rx doesn't parse nlmsg properly
scsi: aacraid: error: testing array offset 'bus' after use
scsi: lpfc: Don't return internal MBXERR_ERROR code from probe function
scsi: aacraid: Fix 2T+ drives on SmartIOC-2000
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform drivers fix from Darren Hart:
"Newly discovered species of fujitsu laptops break some assumptions
about ACPI device pairings.
fujitsu-laptop: Don't oops when FUJ02E3 is not present"
* tag 'platform-drivers-x86-v4.14-2' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: fujitsu-laptop: Don't oops when FUJ02E3 is not presnt
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED fixes from Jacek Anaszewski:
"Four fixes for the as3645a LED flash controller and one update to
MAINTAINERS"
* tag 'led_fixes-4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
MAINTAINERS: Add entry for MediaTek PMIC LED driver
as3645a: Unregister indicator LED on device unbind
as3645a: Use integer numbers for parsing LEDs
dt: bindings: as3645a: Use LED number to refer to LEDs
as3645a: Use ams,input-max-microamp as documented in DT bindings
|
|
Pull MD fixes from Shaohua Li:
"A few fixes for MD. Mainly fix a problem introduced in 4.13, which we
retry bio for some code paths but not all in some situations"
* tag 'md/4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md/raid5: cap worker count
dm-raid: fix a race condition in request handling
md: fix a race condition for flush request handling
md: separate request handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- fix CONFIG_PCI=n build error (introduced in v4.14-rc1) (Geert
Uytterhoeven)
- fix a race in sysfs driver_override store/show (Nicolai Stange)
* tag 'pci-v4.14-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Fix race condition with driver_override
PCI: Add dummy pci_acs_enabled() for CONFIG_PCI=n build
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Regular fixes pull, some amdkfd, amdgpu, etnaviv, sun4i, qxl, tegra
fixes.
I've got an outstanding pull for i915 but it wasn't on an rc2 base so
I wanted to ship these out first, I might get to it before rc3 or I
might not"
* tag 'drm-fixes-for-v4.14-rc3' of git://people.freedesktop.org/~airlied/linux:
drm/tegra: trace: Fix path to include
qxl: fix framebuffer unpinning
drm/sun4i: cec: Enable back CEC-pin framework
drm/amdkfd: Print event limit messages only once per process
drm/amdkfd: Fix kernel-queue wrapping bugs
drm/amdkfd: Fix incorrect destroy_mqd parameter
drm/radeon: disable hard reset in hibernate for APUs
drm/amdgpu: revert tile table update for oland
etnaviv: fix gem object list corruption
etnaviv: fix submit error path
qxl: fix primary surface handling
drm/amdkfd: check for null dev to avoid a null pointer dereference
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- A comment fix for 'struct iommu_ops'
- Format string fixes for AMD IOMMU, unfortunatly I missed that during
review.
- Limit mediatek physical addresses to 32 bit for v7s to fix a warning
triggered in io-page-table code.
- Fix dma-sync in io-pgtable-arm-v7s code
* tag 'iommu-fixes-v4.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu: Fix comment for iommu_ops.map_sg
iommu/amd: pr_err() strings should end with newlines
iommu/mediatek: Limit the physical address in 32bit for v7s
iommu/io-pgtable-arm-v7s: Need dma-sync while there is no QUIRK_NO_DMA
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- avoid a warning when compiling with clang
- consider read-only bits in xen-pciback when writing to a BAR
- fix a boot crash of pv-domains
* tag 'for-linus-4.14c-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/mmu: Call xen_cleanhighmap() with 4MB aligned for page tables mapping
xen-pciback: relax BAR sizing write value check
x86/xen: clean up clang build warning
|
|
git://anongit.freedesktop.org/git/drm-misc into drm-fixes
Driver Changes:
- qxl: fix primary surface and fb unpinning (Gerd)
- sun41: fix CEC_PIN config gate now that media has been merged (Hans)
- tegra: fix TRACE_INCLUDE_PATH (Thierry)
Cc: Thierry Reding <treding@nvidia.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Gerd Hoffmann <kraxel@redhat.com>
* tag 'drm-misc-fixes-2017-09-28-1' of git://anongit.freedesktop.org/git/drm-misc:
drm/tegra: trace: Fix path to include
qxl: fix framebuffer unpinning
drm/sun4i: cec: Enable back CEC-pin framework
qxl: fix primary surface handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"This fixes an APEI problem that may cause a reported error to be
missed due to a race condition"
* tag 'acpi-4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / APEI: clear error status before acknowledging the error
|
